Precision CNC Machinery Surplus from a Mechanical Seals Manufacturer

2018 OKUMA MULTUS U4000 BB/SB-2SW/1500 CNC MULTI-TASKING TURNING CENTER, EXCELLENT LOW-USE CONDITION W/ TWIN TURRETS, RENISHAW PROBE, ROYAL FILTERMIST, H/P COOLANT. SPECIFICATIONS: MODEL: MULTUS U4000 2SW SWING OVER BED: 25.59 INCH DISTANCE BETWEEN CENTERS: 73.70 INCH / 93.39 INCH MAX. TURNING DIAMETER: 25.59 INCH MAX WORKPIECE WEIGHT SUPPORT BETWEEN CENTERS: 1,760 LB MAX WORKPIECE WEIGHT ONE-SIDE SUPPORT: 506 LB LEFT SIDE SPINDLE NOSE: A2-11 LEFT SIDE SPINDLE BORE DIAMETER: 4.41 INCH LEFT SIDE SPINDLE SPEED RANGE: 30 TO 3,000 RPM LEFT SIDE SPINDLE DRIVE MOTOR: 42.7/30 HP RIGHT SIDE SPINDLE NOSE: A2-8 RIGHT SIDE SPINDLE BORE DIAMETER: 3.58 INCH RIGHT SIDE SPINDLE SPEED RANGE: 38 TO 3,800 RPM RIGHT SIDE SPINDLE DRIVE MOTOR: 30/20 HP X-AXIS TRAVEL: 27.36 INCH X-AXIS RAPID TRAVERSE: 1,968.50 IPM Y-AXIS TRAVEL: 11.81 INCH [-5.91 TO +5.91 INCH] Y-AXIS RAPID TRAVERSE: 1,574.80 IPM Z-AXIS TRAVEL (ZA / ZB): 62.99 INCH / 82.68 INCH Z-AXIS RAPID TRAVERSE (ZA / ZB): 1,968.50 IPM / 1,574.80 IPM W-AXIS TRAVEL: 61.18 INCH / 80.87 INCH W-AXIS RAPID TRAVERSE: 1,181.10 IPM C-AXIS CONTROL ANGLE: 360 (MIN. CONTROL ANGLE 0.001) C-AXIS RAPID TRAVERSE: 200 MIN-1 B-AXIS INDEX RANGE: -30 TO 210 DEGREE B-AXIS INDEX ANGLE: 0.001 DEGREE UPPER TURRET TYPE: H1 UPPER TURRET NUMBER OF TOOLS: 1 L OR M TOOL ATC MAGAZINE TOOL SHANK: CAPTO C6 ATC MAGAZINE STORAGE CAPACITY: 80 TOOLS MAX. TOOL MASS: 22 LB MAX. TOOL LENGTH: 15.75 INCH (EXCEPT SHANK PART) MAX. TOOL DIAMETER (WITH ADJACENT TOOLS): 3.54 INCH MAX. TOOL DIAMETER (WITHOUT ADJACENT TOOLS): 5.12 INCH MILLING TOOL SPINDLE SPEED: 12,000 RPM MILLING TOOL SPINDLE MAX. TORQUE: 120/80/60 N-M MILLING TOOL SPINDLE DRIVE: 30/20/15 HP LOWER TURRET TYPE: V12 TURRET W-AXIS FEED MOTOR: 6.13 HP X-AXIS FEED MOTOR: 6.93 HP Y-AXIS FEED MOTOR: 4.67 HP Z-AXIS FEED MOTOR: 6.13 HP / 6.93 HP TA-AXIS FEED MOTOR: 4.00 HP HYDRAULIC PUMP MOTOR: 3 HP LUBRICATION PUMP MOTOR: 0.0227 HP COOLANT PUMP MOTOR: 1.07 HP MAGAZINE ROTATION MOTOR: 2.27 HP ATC MOTOR: 2.27 HP GENERAL POWER DBC 1500/2000: 57.5 KVA / 57.6 KVA VOLTAGE: 200 V PRIMARY VOLTAGE TAP OF THE TRANSFORMER SUPPLIED FROM OKUMA: 220/240/380/415/440/480 V FREQUENCY: 50/60 HZ PROTECT LEVEL FOR CONTROL CABINET: IEC IP54 GENERAL POWER (MACHINE PLATE): 90 KVA SUPPLY VOLTAGE: 220/480 V PHASE: 3 P FULL LOAD CURRENT: 236.2/108.3 A LARGEST MOTOR RATING: 203 A INTERRUPTING CAPACITY: 36/5 KA SCCR OF CONTROL PANEL: 10 KA MACHINE HEIGHT: 119.29 INCH REQUIRED FLOOR SPACE DBC 1500/2000: 5,425 X 3,082 MM / 6,175 X 3,082 MM NET MASS DBC 1500/2000: 41,800 LB DATE OF MANUFACTURE: DECEMBER 2018 COUNTRY OF MANUFACTURE: MADE IN JAPAN MACHINE RUN HOURS: RUNNING TIME: 16,514:57 HRS OPERATING TIME: 6,226:30:04 HRS CUTTING TIME: 5,440:36:56 HRS SPINDLE RUN TIME: 3,787:27:05 HRS EQUIPPED WITH: OKUMA OSP P300 CNC CONTROL TWIN WORKHOLDING PACKAGE: SPINDLE 1 & SPINDLE 2 COMPLETE CHUCKING PACKAGES TWO (2) SMW AUTOBLOK KNCS-2G 400-128 3-JAW POWER CHUCKS 80-STATION AUTOMATIC TOOL CHANGER (ATC) MAGAZINE LEFT SIDE SPINDLE BIG BORE (BB) OPTION (4.41 INCH BORE / A2-11 SPINDLE NOSE) RIGHT SIDE SPINDLE STANDARD BORE (SB) (3.58 INCH BORE / A2-8 SPINDLE NOSE) DUAL TURRET CONFIGURATION: UPPER H1 (0.001 DEGREE MILLING/TURNING) & LOWER V12 TURRET AUTOMATIC TOUCHSETTER RENISHAW RMP 600 GAUGING / 3D TOUCH PROBE RENISHAW RMI-Q RADIO MACHINE INTERFACE / RECEIVER MP SYSTEMS VR8 PROGRAMMABLE 1000 PSI HIGH PRESSURE COOLANT SYSTEM MP SYSTEMS RC-36 480V COOLANT TEMPERATURE CONTROL / CHILLER UNIT HAKUSAN KIKO CO. CHIP CONVEYOR, HIGH FILTER 1500BCD & COOLANT UNIT ROYAL FILTERMIST FX-1200 MIST COLLECTOR UNIT (MODEL FX-1200) AUTO DOOR W/ DUAL CYCLE START PREP FOR MIST 6 INCH STD LATHE RAPID TRAVERSE OVERRIDE SWITCH SPARE M-CODES, 8 SETS SHOWER COOLANT NIAGARA B TYPE LATHE TOOL INDEX FUNCTION - MULTI EDGE GRADING OVER THE CHIP CONVEYOR S/N: 218923

2019 OKUMA MULTUS U4000 BB/SB-2SW/1500 CNC MULTI-TASKING TURNING CENTER, EXCELLENT LOW-USE CONDITION W/ TWIN TURRETS, RENISHAW PROBE, ROYAL FILTERMIST, H/P COOLANT. SPECIFICATIONS: MODEL: MULTUS U4000 2SW SWING OVER BED: 650 (25.59 INCH) DISTANCE BETWEEN CENTERS: 1,872 (73.70 INCH) / 2,372 (93.39 INCH) MAX. TURNING DIAMETER: 650 (25.59 INCH) MAX WORKPIECE WEIGHT SUPPORT BETWEEN CENTERS: 800 KG (1,760 LB) MAX WORKPIECE WEIGHT ONE-SIDE SUPPORT: 230 KG (506 LB) LEFT SIDE SPINDLE NOSE: A2-11 LEFT SIDE SPINDLE BORE DIAMETER: 4.41 INCH LEFT SIDE SPINDLE SPEED RANGE: 30 TO 3,000 RPM LEFT SIDE SPINDLE DRIVE MOTOR: VAC 32/22 KW (42.7/30 HP) (20 MIN/CONT.) RIGHT SIDE SPINDLE NOSE: A2-8 RIGHT SIDE SPINDLE BORE DIAMETER: 3.58 INCH RIGHT SIDE SPINDLE SPEED RANGE: 38 TO 3,800 RPM RIGHT SIDE SPINDLE DRIVE MOTOR: VAC 22/15 KW (30/20 HP) (30 MIN/CONT.) X-AXIS TRAVEL: 695 (27.36 INCH) X-AXIS RAPID TRAVERSE: 50,000 MM/MIN (1,968.50 IPM) Y-AXIS TRAVEL: 300 (11.81 INCH) [-150 (5.91 INCH) TO +150 (5.91 INCH)] Y-AXIS RAPID TRAVERSE: 40,000 MM/MIN (1,574.80 IPM) Z-AXIS TRAVEL (ZA / ZB): 1,600 (62.99 INCH) / 2,100 (82.68 INCH) Z-AXIS RAPID TRAVERSE (ZA / ZB): 50,000 MM/MIN (1,968.50 IPM) / 40,000 MM/MIN (1,574.80 IPM) W-AXIS TRAVEL: 1,554 (61.18 INCH) / 2,054 (80.87 INCH) W-AXIS RAPID TRAVERSE: 30,000 MM/MIN (1,181.10 IPM) C-AXIS CONTROL ANGLE: 360 (MIN. CONTROL ANGLE 0.001) C-AXIS RAPID TRAVERSE: 200 MIN-1 B-AXIS INDEX RANGE: -30 TO 210 DEGREE B-AXIS INDEX ANGLE: 0.001 DEGREE UPPER TURRET TYPE: H1 UPPER TURRET NUMBER OF TOOLS: 1 L OR M TOOL ATC MAGAZINE TOOL SHANK: CAPTO C6 ATC MAGAZINE STORAGE CAPACITY: 80 TOOLS MAX. TOOL MASS: 10 KG (22 LB) MAX. TOOL LENGTH: 400 (15.75 INCH) MAX. TOOL DIAMETER (WITH ADJACENT TOOLS): 90 (3.54 INCH) MAX. TOOL DIAMETER (WITHOUT ADJACENT TOOLS): 130 (5.12 INCH) MILLING TOOL SPINDLE SPEED: 12,000 RPM MILLING TOOL SPINDLE MAX. TORQUE: 120/80/60 N-M [3 MIN/15 MIN/CONT.] MILLING TOOL SPINDLE DRIVE: 22/15/11 KW (30/20/15 HP) [3 MIN/15 MIN/CONT.] LOWER TURRET TYPE: V12 TURRET W-AXIS FEED MOTOR: 4.6 KW (6.13 HP) X-AXIS FEED MOTOR: 5.2 KW (6.93 HP) Y-AXIS FEED MOTOR: 3.5 KW (4.67 HP) Z-AXIS FEED MOTOR: 4.6 KW (6.13 HP) / 5.2 KW (6.93 HP) TA-AXIS FEED MOTOR: 3.0 KW (4.00 HP) HYDRAULIC PUMP MOTOR: 2.2 KW (3 HP) LUBRICATION PUMP MOTOR: 0.017 KW (0.0227 HP) COOLANT PUMP MOTOR: 0.8 KW (1.07 HP) MAGAZINE ROTATION MOTOR: 1.7 KW (2.27 HP) ATC MOTOR: 1.7 KW (2.27 HP) GENERAL POWER DBC 1500/2000: 57.5 KVA (OP. 77.3) / 57.6 KVA (OP. 77.5) VOLTAGE: 200 V PRIMARY VOLTAGE TAP OF THE TRANSFORMER SUPPLIED FROM OKUMA: 220/240/380/415/440/480 V FREQUENCY: 50/60 HZ PROTECT LEVEL FOR CONTROL CABINET: IEC IP54 GENERAL POWER (MACHINE PLATE): 90 KVA SUPPLY VOLTAGE: 220/480 V PHASE: 3 P FULL LOAD CURRENT: 236.2/108.3 A LARGEST MOTOR RATING: 203 A INTERRUPTING CAPACITY: 36/5 KA SCCR OF CONTROL PANEL: 10 KA DIAGRAM NO: W5201-218-924 MACHINE HEIGHT: 3,030 (119.29 INCH) REQUIRED FLOOR SPACE DBC 1500/2000: 5,425 X 3,082 MM / 6,175 X 3,082 MM NET MASS DBC 1500/2000: 19,000 KG (41,800 LB) DATE OF MANUFACTURE: 2019.01 (JANUARY 2019) COUNTRY OF MANUFACTURE: MADE IN JAPAN MACHINE RUN HOURS: RUNNING TIME: 16,330:21 HRS OPERATING TIME: 6,187:35:37 HRS CUTTING TIME: 5,162:45:43 HRS SPINDLE RUN TIME: 3,506:09:33 HRS EQUIPPED WITH: OKUMA OSP P300 CNC CONTROL TWIN WORKHOLDING PACKAGE: SPINDLE 1 & SPINDLE 2 COMPLETE CHUCKING PACKAGES TWO (2) SMW AUTOBLOK KNCS-2G 400-128 3-JAW POWER CHUCKS (MADE IN GERMANY) 80-STATION AUTOMATIC TOOL CHANGER (ATC) MAGAZINE LEFT SIDE SPINDLE BIG BORE (BB) OPTION (4.41 INCH BORE / A2-11 SPINDLE NOSE) RIGHT SIDE SPINDLE STANDARD BORE (SB) (3.58 INCH BORE / A2-8 SPINDLE NOSE) DUAL TURRET CONFIGURATION: UPPER H1 (0.001 DEGREE MILLING/TURNING) & LOWER V12 TURRET AUTOMATIC TOUCHSETTER RENISHAW RMP 600 GAUGING / 3D TOUCH PROBE RENISHAW RMI-Q RADIO MACHINE INTERFACE / RECEIVER MP SYSTEMS VR8 PROGRAMMABLE 1000 PSI HIGH PRESSURE COOLANT SYSTEM MP SYSTEMS RC-36 480V COOLANT TEMPERATURE CONTROL / CHILLER UNIT HAKUSAN KIKO CO. CHIP CONVEYOR, HIGH FILTER 1500BCD & COOLANT UNIT (ISHIKAWA, JAPAN) ROYAL FILTERMIST FX-1200 MIST COLLECTOR UNIT (MODEL FX-1200) AUTO DOOR W/ DUAL CYCLE START PREP FOR MIST 6 INCH STD LATHE RAPID TRAVERSE OVERRIDE SWITCH SPARE M-CODES, 8 SETS SHOWER COOLANT NIAGARA B TYPE LATHE TOOL INDEX FUNCTION - MULTI EDGE GRADING OVER THE CHIP CONVEYOR S/N: 218924

2012 OKUMA SPACE TURN LB4000 EX /750 CNC TURNING CENTER W/ ROYAL QUICK-CHANGE CHUCK. MODEL: LB4000 EX X750 (HIGH-TORQUE 2-AXIS VARIANT). CONTROL TYPE: OKUMA OSP-P200LA. MAXIMUM SWING OVER BED: 26.38" (670 MM). MAXIMUM SWING OVER CROSS SLIDE: 23.62" (600 MM). MAXIMUM TURNING DIAMETER: 18.90" (480 MM). MAX TURNING LENGTH (750 BED VARIANT): 29.53" (750 MM). SPINDLE SPEED RANGE: 42 ~ 4,200 RPM. SPINDLE NOSE CONFIGURATION: JIS A2-8. THROUGH-SPINDLE HOLE DIAMETER: 3.54" (90 MM). STANDARD BAR CAPACITY PROFILE: 3.15" (80 MM). MAIN SPINDLE MOTOR POWER (30 MIN): 40 HP (30 KW). TURRET CAPACITY: 12-STATION RADIAL V12 DISK TURRET. X-AXIS TRAVEL: 11.81" (300 MM). Z-AXIS TRAVEL: 33.07" (840 MM). X-AXIS RAPID TRAVERSE RATE: 984 IPM (25 M/MIN). Z-AXIS RAPID TRAVERSE RATE: 1,181 IPM (30 M/MIN). SUPPLY VOLTAGE CONNECTION: 220 / 480 V, 3-PHASE, 60 HZ. RATED POWER CAPACITY: 49.6 KVA. FULL LOAD CURRENT: 130.2 / 59.7 A. LARGEST MOTOR DRAW RATING: 219 A. SHORT-CIRCUIT INTERRUPTING CAPACITY: 30 / 10 KA. NET MASS OF MACHINE: APPROX 14,800 LBS TO 16,000 LBS. COUNTRY OF MANUFACTURE: MADE IN JAPAN. MACHINE OPERATING PERIOD DIAGNOSTICS: RUNNING LOG TIME: 35,717 HOURS, 30 MINUTES. OPERATING LOG TIME: 11,009 HOURS, 07 MINUTES. ACTIVE TOOL CUTTING TIME: 10,584 HOURS, 44 MINUTES. SETUP MODE INTERVAL: 24,707 HOURS, 58 MINUTES. SPINDLE ROTATION RUNNING TIME COUNTER: 11,506 HOURS, 15 MINUTES. EQUIPPED WITH: OKUMA OSP-P200LA CNC COLOR DISPLAY CONSOLE TERMINAL WITH INTEGRATED ALPHA-NUMERIC KEYBOARD & DIAL JOG PULSE WHEEL. FORKARDT / ROHM 15" HEAVY-DUTY QUICK-CHANGE 3-JAW POWER CHUCK (MODEL: KNCS-N-400-128, MAX 3500 MIN1). HEAVY-DUTY FULLY PROGRAMMABLE HYDRAULIC CARRIAGE DRAG TAILSTOCK BASE WITH QUILL LIVE SPINDLE CENTER. ROYAL FILTERMIST CENTRIFUGAL OIL MIST AIR COLLECTOR UNIT (MODEL FX-550, SERIAL NO: 002452). DAIKIN INDUSTRIAL OIL COOLING TEMPERATURE REGULATION UNIT (MODEL: AKZ149, RATED 0.90KW, R410A REFRIGERANT LOOP SYSTEM). S/N: 163347

1999 MORI SEIKI SL-400BMC/2000 CNC TURNING CENTER W/ LIVE TOOLING & SMW STEADY REST SN: 269 MODEL: SL-400BMC/2000 (MILLING VARIANT / EXTENDED BED CONFIGURATION) DATE OF MFG: 11 / 1999 CONTROL TYPE: MORI SEIKI MSC SERIES (FANUC BASED) SWING OVER BED: 36.8" (935 MM) MAX. TURNING DIAMETER: 25.4" (645 MM) MAX. TURNING LENGTH: EXTENDED 2,000MM BED CONFIGURATION (APPROX. 80" TO 84.9" MAX) MAX. BAR CAPACITY: 4.33" TO 5.11" X-AXIS TRAVEL: 11.3" Z-AXIS TRAVEL: EXTENDED BED-LENGTH STROKE MATCHING 2,000MM ARCHITECTURE MAIN SPINDLE SPEED RANGE: 10 - 2,400 RPM MAIN SPINDLE MOTOR: 40 HP MILLING MOTOR POWER (LIVE TOOLING): 15 HP SPINDLE NOSE TAPER: A2-11 TURRET CAPACITY: 12-STATION TURRET (SUPPORTS TURNING AND LIVE MILLING) SUPPLY VOLTAGE: 220 V AC, 3-PHASE, 60 HZ FULL LOAD CURRENT: 234 A CURRENT RATING OF SPINDLE MOTOR: 139 A INTERRUPTING CAPACITY: 5 KA RATED POWER: 81 KVA MASS OF MACHINE: 16,500 KG (36,376 LBS) ELECTRICAL DIAGRAM NO.: AFJ0210 COUNTRY OF MANUFACTURE: MADE IN JAPAN (YAMATOKORIYAMA CITY, NARA) STEADY REST SPECIFICATIONS: MANUFACTURER: SMS AMERICA INC. (SMW AUTOBLOK) STEADY REST MODEL: SLU-5.0/Z STEADY REST SERIAL NUMBER: 2744 MAXIMUM CLAMPING DIAMETER: 12.205" MINIMUM CLAMPING DIAMETER: 1.772" MAXIMUM OPERATING PRESSURE: 1,160 PSI PISTON AREA: 12.17 SQ IN GREASE SYSTEM REQUIREMENT: MOBIL MOBILITH 220 OIL SYSTEM REQUIREMENT: MOBIL DTE 25 MACHINE OPERATING METRICS: RUN TIME: 24,143 HOURS, 50 MINUTES PART COUNT: 3,807 PARTS EQUIPPED WITH: SMW AUTOBLOK SLU-5.0/Z HYDRAULIC SELF-CENTERING STEADY REST FRAME ASSEMBLY KITAGAWA 18" 3-JAW HYDRAULIC CHUCK (MODEL B-18, SERIAL: E6184, MADE IN JAPAN) ROYAL FILTERMIST F1200 MIST COLLECTOR / AIR FILTRATION SYSTEM (MODEL F1200, SERIAL: 12-4048) FANUC CNC INTELLIGENCE INTERNAL POWER CABINET SYSTEM (EQUIPPED WITH FANUC SERVO/SPINDLE MODULES) HEAVY-DUTY VARIABLE TAILSTOCK SYSTEM W/ LIVE QUILL TAPER SPINDLE HEAD

2006 OKUMA MU-400VA CNC MACHINING CENTER W/ RENISHAW NC4TX, FILTERMIST FX-575, CONSEP CONVEYOR S/N: 126734 SPECIFICATIONS: MODEL: MU-400VA (UNIVERSAL CENTER) PRODUCED/DATE OF MFG: 2006.10 CONTROL TYPE: OKUMA OSP-P200M X-AXIS TRAVEL: 30.0" (762 MM) Y-AXIS TRAVEL: 18.11" (460 MM) Z-AXIS TRAVEL: 18.11" (460 MM) A-AXIS TRAVEL (TILT): +20 TO -110 DEGREES C-AXIS TRAVEL (ROTATION): 360 DEGREES TABLE SIZE: 15.75" DIAMETER (400 MM) WORKING AREA: 15.75" X 15.75" (400 MM X 400 MM) FLOOR TO TABLE UPPER FACE DISTANCE: 41.34" (1,050 MM) MAX. TABLE LOADING CAPACITY: 660 LBS (300 KG) MAX. SPINDLE SPEED: 8,000 RPM TAPERED BORE: 7/24 TAPER NO. 40 BEARING ID: 2.76" (70 MM) RAPID TRAVERSE RATES (X, Y, Z): X, Y: 1574.80 IPM (40 M/MIN) / Z: 1259.84 IPM (32 M/MIN) CUTTING FEEDRATES (X, Y, Z): X, Y, Z: 1259.84 IPM (32 M/MIN) SPINDLE DRIVE MOTOR (10 MIN/CONT): 15 / 11 KW (20 / 15 HP) AXIS FEED MOTOR (X, Y, Z): X, Y: 4.0 KW (5.4 HP) / Z: 4.3 KW (5.7 HP) TOOL STORAGE CAPACITY: 20 TOOLS (ATC) MAX. TOOL DIAMETER (WITH ADJACENT TOOLS): 3.54" (90 MM) MAX. TOOL DIAMETER (WITHOUT ADJACENT TOOLS): 4.92" (125 MM) MAX. TOOL LENGTH: 9.45" (240 MM) MAX. TOOL WEIGHT: 17.6 LBS (8 KG) MACHINE HEIGHT: 116.14" (2,950 MM) REQUIRED FLOOR SPACE (WIDTH X DEPTH): 85.04" X 106.89" (2,160 MM X 2,715 MM) MACHINE WEIGHT: 16,940 LBS (7,700 KG) GUIDEWAY TYPE: X-AXIS SADDLE FEED RAM TYPE / 3-AXIS LINEAR GUIDE COOLANT TANK CAPACITY: 100 GALLONS (370 L) POWER CAPACITY REQUIREMENTS: 220/480V, 60HZ, 3-PHASE, 39 KVA CONTINUOUS MACHINE OPERATING METRICS: RUNNING TIME: 67,256 HOURS OPERATING TIME: 27,368 HOURS CUTTING TIME: 24,309 HOURS SPINDLE RUN TIME: 26,779 HOURS EQUIPPED WITH: OKUMA OSP-P200M WINDOWS-BASED CNC CONTROL UNIT W/ COLOR LCD MONITOR TRUNNION-STYLE INTEGRATED A/C AXIS ROTARY TILT TABLE 20-STATION AUTOMATIC TOOL CHANGER DRUM ASSEMBLY RENISHAW NC4TX LASER TOOL SETTER PROBE SYSTEM RENISHAW "IN ACTION" PROBE SOFTWARE SYSTEM CONNECTION INTERFACE ROYAL FILTERMIST FX-575 CENTRIFUGAL MIST COLLECTOR / AIR FILTRATION UNIT (MODEL FX-575, SERIAL: 57FX003493) TSUBAKI-MAYFRAN INC. CONSEP 2000 SEPARATION & HINGED BELT CHIP CONVEYOR SYSTEM (MODEL CONSEP 2000)

2011 HAAS VF-2 CNC VERTICAL MACHINING CENTER W/ RENISHAW SN: 1085994 SPECIFICATIONS: MODEL: VF-2 DATE OF MFG: 06 / 11 CONTROL TYPE: HAAS CNC CONTROL INTERFACE X-AXIS TRAVEL: 30 INCH (762 MM) Y-AXIS TRAVEL: 16 INCH (406 MM) Z-AXIS TRAVEL: 20 INCH (508 MM) SPINDLE NOSE TO TABLE DISTANCE: 4 TO 24 INCH (102 TO 610 MM) TABLE SIZE: 36 INCH X 14 INCH (914 MM X 356 MM) MAXIMUM WEIGHT ON TABLE (BALANCED): 3,000 LBS (1,361 KG) MAX SPINDLE SPEED: 8,100 RPM SPINDLE MOTOR MAX RATING: 20 HP VECTOR DRIVE MAXIMUM TORQUE: 90 FT-LB @ 2,000 RPM SPINDLE TAPER: CAT 40 TOOL CHANGER CAPACITY: 20-STATION CAROUSEL TYPE MAX CUTTING FEEDRATE: 650 IPM (16.5 M/MIN) RAPID TRAVERSE RATES (X/Y/Z): 1,000 IPM (25.4 M/MIN) VOLTAGE CONFIGURATION: 195 - 260 VAC PHASE: 3-PHASE FREQUENCY: 50 / 60 HZ FULL LOAD AMPERAGE: 40 AMPS LARGEST LOAD AMPERAGE: 35 AMPS SHORT CIRCUIT INTERRUPTING CAPACITY: 10,000 AMPS AIR REQUIRED: 100 PSI CONTINUOUS @ 4 SCFM MACHINE DIMENSIONS (APPROX): 101 INCH L X 99 INCH W X 101 INCH H MACHINE WEIGHT: APPROXIMATELY 7,800 LBS (3,538 KG) COUNTRY OF MANUFACTURE: MADE IN U.S.A. (OXNARD, CA) MACHINE RUN HOURS: POWER ON TIME: 23,834 HOURS, 25 MINUTES CYCLE START TIME: 2,686 HOURS, 25 MINUTES FEED CUTTING TIME: 2,229 HOURS, 19 MINUTES EQUIPPED WITH: RENISHAW OMP40-2 WIRELESS OPTICAL MACHINE WORKPIECE PROBE UNIT RENISHAW OTS WIRELESS OPTICAL TABLE TOOL SETTER PROBE HAAS VECTOR DRIVE CLOSED LOOP MODULE SYSTEM (20/15 HP CLASS) 20-SLOT RADIAL CAROUSEL STYLE AUTOMATIC TOOL CHANGER RING RIGID TAPPING OPTION SOFTWARE SET COORDINATE ROTATION AND SCALING CONTROL OPTION INTEGRATION FRONT ACCESS DOUBLE SLIDE DOOR SAFETY ENCLOSURE ARCHITECTURE SIDE-MOUNTED STORAGE ORGANIZER TRAYS (ATTACHED TO LEFT COLUMN BODY) (NOTE: 4TH AXIS ROTARY TABLE DEVICE SHOWN IS EXCLUDED FROM LOT)

2006 MAZAK QTN 450-II CNC LATHE W/ MAZATROL MATRIX, SMW AUTOBLOK CHUCK. SPECIFICATIONS: MODEL NAME: QUICK TURN NEXUS 450-II DATE OF MFG: 09 / 2006 CONTROL TYPE: MAZATROL MATRIX NEXUS CNC SYSTEM MAXIMUM SWING DIAMETER: 33.268" (845 MM) STANDARD MACHINING DIAMETER: 13.228" (336 MM) MAXIMUM MACHINING DIAMETER: 22.835" (580 MM) DISTANCE BETWEEN SPINDLE END AND TURRET FACE: 6.664" TO 48.994" (178 MM TO 1243 MM) MAX. SUPPORT WEIGHT (CHUCK WORK ONLY): 2,205 LBS (1000 KG) MAX. SUPPORT WEIGHT (SHAFT WORK W/ TAILSTOCK SUPPORT): 2,923 LBS (1326 KG) MAIN SPINDLE SPEED RANGE: UP TO 2,000 RPM NUMBER OF TURRET TOOL POCKETS: 12 POSITION INDEXING TURRET DISC ARRAY OUTSIDE TURNING TOOL SHANK SIZE: 1.26" SQUARE (32 MM) INSIDE TURNING TOOL BORE SIZE: 2.0" (50 MM) TAILSTOCK CENTER BORE TAPER: BUILT-IN CENTER NO. 5 TAILSTOCK QUILL TOTAL TRAVEL STROKE: 40.354" (1025 MM) TAILSTOCK MAXIMUM CONTINUOUS THRUST CAPACITY: 2,923 LBF (13000 N) X-AXIS TRAVEL STROKE: 13.375" (340 MM) X-AXIS RAPID TRAVERSE RATE: 1,181 IPM (30 M/MIN) Z-AXIS TRAVEL STROKE (1000 BED VARIANT): 42.125" (1070 MM) Z-AXIS RAPID TRAVERSE RATE: 1,181 IPM (30 M/MIN) COOLANT TANK BASE FLUID CAPACITY: 84.5 GALLONS (320 LITERS) MAIN UTILITY POWER INPUT REQUIREMENTS: 3-PHASE AC, 208V, 50/60 HZ RATED CONTINUOUS POWER CAPACITY: 60 KVA (166 AMPS CIRCUIT BREAKER LOAD PROTECTION) C.B. RATING: 50 / 25 KA INTERRUPTING CAPACITY MACHINE FOOTPRINT DIMENSIONS (APPROX. LENGTH X WIDTH): 174.29" X 93.94" (4427 MM X 2386 MM) MACHINE OPERATIONAL STRUCTURAL HEIGHT: 80.41" (2042.3 MM) NET BASE STRUCTURAL MACHINE MASS / WEIGHT: 22,220 LBS (10100 KG) COUNTRY OF MANUFACTURE: MADE IN U.S.A. (FLORENCE, KY) EQUIPPED WITH: MAZATROL MATRIX NEXUS CNC GRAPHIC COMMAND DISPLAY CONTROL CONSOLE DASHBOARD PANEL SMW AUTOBLOK 15" HEAVY-DUTY QUICK-CHANGE 3-JAW POWER CHUCK (MODEL: KNCS-N-400-128, ID NO: 410055, MAX 3500 MIN1, MADE IN GERMANY) 12-POCKET HIGH-RIGIDITY RADIAL TOOL INDEXING BLOCK TURRET FACE ASSEMBLY RENTSCHLER-REVEN LUFTUNGSSYSTEME GMBH REVEN MIST FILTER / INDUSTRIAL AIR CLEANER COLLECTOR UNIT JORGENSEN CONVEYORS INC HEAVY-DUTY HINGED STEEL BELT CHIP CONVEYOR (SERIAL NO: A-061000-4, DATE: 09-14-06) HEAVY-DUTY PROGRAM-DRIVEN PROGRAMMABLE WORKPIECE SLANTED LATHE TAILSTOCK UNIT ASSEMBLY S/N: 189111

2007 OKUMA CAPTAIN L470BBM CNC TURNING CENTER W/ TURBO CONVEYOR & ROYAL FILTERMIST SN: 129082 SPECIFICATIONS: MODEL: CAPTAIN-L470 CONFIGURATION VARIANT: BBM (BIG BORE, LIVE MILLING, C-AXIS) SPECIFICATION TABLE VARIANT: C-SPEC. (BETWEEN-CENTER DISTANCE: 650) NO. OF CONTROLLED AXES: 2 (3:M TYPE) SWING OVER BED: 620 MM (24.41 IN.) SWING OVER CARRIAGE: 620 MM (24.41 IN.) SWING OVER CROSS-SLIDE: 480 MM (18.90 IN.) DISTANCE BETWEEN CENTERS: 670 MM (26.38 IN.) MAX. TURNING DIAMETER X LENGTH: 420 X 650 MM (16.54 X 25.59 IN.) M TYPE SPINDLE NOSE TYPE: JIS A2-11 SPINDLE SPEED: 30 - 3,000 MIN-1 SPINDLE DIAMETER: 150 MM (5.91 IN.) TAPER HOLE: 120 MM (4.72 IN.) X 1/10 THROUGH-SPINDLE HOLE: 110 MM (4.33 IN.) DRAWTUBE / BAR CAPACITY: APPROX. 3.62 TO 4.0 IN. NO. OF SPINDLE SPEED RANGES: 1 STEP CARRIAGE (Z-AXIS) AXIS TRAVEL: 675 MM (26.57 IN.) CARRIAGE (Z-AXIS) FEED RATE: 0.001 - 1,000.00 MM/REV (0.00001 - 39.37 IPR) CARRIAGE (Z-AXIS) RAPID FEED RATE: 25,000 MM/MIN (984.25 IPM) CROSS-SLIDE (X-AXIS) AXIS TRAVEL: 300 MM (11.81 IN.) [90 + 210 (3.54 + 8.27)] CROSS-SLIDE (X-AXIS) FEED RATE: 0.001 - 1,000.00 MM/REV (0.00001 - 39.37 IPR) CROSS-SLIDE (X-AXIS) RAPID FEED RATE: 20,000 MM/MIN (787.25 IPM) TURRET TYPE: V12 TURRET NO. OF TOOLS: 12 TOOL SIZE OD TURNING TOOLS: 25 X 25 MM (1 X 1 IN.) TOOL SIZE ID TURNING TOOLS: 40 MM (1 1/2 IN.) ROTARY TOOL SPINDLE SPINDLE SPEED: 200 MIN-1 ROTARY TOOL SPINDLE NO. OF SPEED RANGES: INFINITELY VARIABLE C-AXIS CONTROL ANGLE: 360 DEGREE (INCREMENT: 0.001) C-AXIS RAPID TRAVERSE: 200 MIN-1 TAILSTOCK SPINDLE DIAMETER: 100 MM (3.94 IN.) TAILSTOCK SPINDLE TAPER HOLE: MT NO. 5 TAILSTOCK SPINDLE TRAVEL: 150 MM (5.91 IN.) SPINDLE DRIVE MOTOR: 22/15 KW (30/20 HP) (20 MIN/CONT.) CARRIAGE FEED (Z-AXIS) MOTOR: 6 KW (8 HP) CROSS-SLIDE FEED (X-AXIS) MOTOR: 4 KW (5.3 HP) HYDRAULIC POWER UNIT PUMP MOTOR: 2.2 KW (3 HP) GUIDEWAY LUBRICATION PUMP MOTOR: 0.018 KW (0.024 HP) COOLANT PUMP MOTOR: 0.25 KW (0.333 HP) FOR SIDE DISPOSAL TYPE, 0.8 (1.067 HP) FOR REAR DISPOSAL TYPE SUPPLY VOLTAGE: 220/480 V PHASE: 3 P FREQUENCY: 60 HZ RATED CAPACITY: 27.7 KVA FULL LOAD CURRENT: 72.7 / 33.4 A LARGEST MOT. RATE: 114 A INTERRUP. CAP.: 25/10 KA DIAGRAM NO.: W5201-129-082 MACHINE HEIGHT: 1,885 MM (74.21 IN.) FLOOR SPACE REQUIRED: 2,700 X 1,900 MM (106.30 X 74.80 IN.) NET MASS: 5,400 KG (11,880 LB) M TYPE COUNTRY OF MANUFACTURE: MADE IN JAPAN DATE OF MANUFACTURE: 04/2007 MACHINE RUN HOURS: RUNNING TIME: 44,039:38 HRS OPERATING TIME: 11,985:35 HRS CUTTING TIME: 10,853:22 HRS NOT OPERATING: 32,053:30 HRS IN-PRO SETUP: 32,053:30 HRS EQUIPPED WITH: OKUMA OSP CNC CONTROL M-FUNCTION CONFIGURATION (LIVE TOOLING/MILLING CAPABILITIES) FULL C-AXIS SPINDLE INDEXING (0.001 DEGREE) BIG BORE (BB) FACTORY OPTION PACKAGE (4.33" SPINDLE BORE) SMW ULTIMATE CHUCK (NCSE 315-104, MADE IN GERMANY) TURBO SYSTEMS INCORPORATED CHIP CONVEYOR (MODEL 5475-8760) ROYAL FILTERMIST FX-900 MIST COLLECTOR UNIT (MODEL FX-900) FOOT SWITCH OPERATION

2008 OKUMA LU300-M TWIN-TURRET CNC LATHE W/ LIVE TOOLING, ATS CHUCK & MAYFRAN CONVEYOR. MODEL: LU300-M2SC600 (4-AXIS TWIN-TURRET LIVE TOOLING VARIANT). PRODUCED / DATE OF MFG: 2008.09. CONTROL TYPE: OKUMA OSP SERIES. NO. OF CONTROLLED AXES: 4. SWING OVER BED: 20.87" (530 MM). SWING OVER SADDLE (UPPER TURRET): 16.14" (410 MM). SWING OVER SADDLE (LOWER TURRET): 12.60" (320 MM). DISTANCE BETWEEN CENTERS: 23.62" (600 MM). MAX. TURNING DIAMETER X LENGTH: 13.39" X 23.62" (340 MM X 600 MM). SPINDLE NOSE TYPE: JIS A2-8. THROUGH-SPINDLE HOLE DIAMETER: 3.14" (80 MM). SPINDLE BEARING INNER DIAMETER: 4.72" (120 MM). SPINDLE SPEED RANGE: 45 - 4,500 MIN1 (INFINITELY VARIABLE). X-AXIS TRAVEL (UPPER TURRET): 10.24" [70 MM + 190 MM] (260 MM). X-AXIS TRAVEL (LOWER TURRET): 5.51" [30 MM + 110 MM] (140 MM). Z-AXIS TRAVEL (UPPER TURRET): 25.20" (640 MM). Z-AXIS TRAVEL (LOWER TURRET): 24.21" (615 MM). TURRET TYPE (UPPER / LOWER): TWIN TURRET SETUP (V12 UPPER / V8 LOWER). NUMBER OF TOTAL TOOL STATIONS: 20 STATIONS (12 UPPER / 8 LOWER). OD TURNING TOOL SHANK SIZE: 1" X 1" (25 MM X 25 MM). ID TURNING TOOL BORE SIZE: 1-1/2" (40 MM DIAMETER). ROTARY TOOL SPINDLE SPEED RANGE: 45 - 4,500 MIN1. SPINDLE DRIVE MOTOR (30 MIN / CONT): VAC 22 / 15 KW (30 / 20 HP). UPPER TURRET AXIS FEED MOTORS: X: 4.0 KW (5.3 HP) / Z: 4.0 KW (5.3 HP). LOWER TURRET AXIS FEED MOTORS: X: 2.2 KW (3.0 HP) / Z: 4.0 KW (5.3 HP). COOLANT PUMP MOTOR: 0.8 KW (1.067 HP). HYDRAULIC POWER UNIT PUMP MOTOR: 2.2 KW (3.0 HP). GUIDEWAY LUBRICATION PUMP MOTOR: 0.018 KW (0.024 HP). REQUIRED MACHINE HEIGHT: 85.67" (2,176 MM). FLOOR SPACE REQUIRED (WIDTH X DEPTH): 155.51" X 89.76" (3,950 MM X 2,280 MM). NET MASS OF MACHINE: 14,960 LBS (6,800 KG). SUPPLY VOLTAGE: 220 / 480 V, 3-PHASE, 60 HZ. RATED CAPACITY: 29.9 KVA. FULL LOAD CURRENT: 78.5 / 36.4 A. LARGEST MOTOR AMPERAGE RATE: 96 A. SHORT-CIRCUIT INTERRUPTING CAPACITY: 30 / 10 KA. ELECTRICAL DIAGRAM NO: W5201-142-264. MACHINE OPERATING METRICS: RUNNING TIME: 55,031 HOURS, 09 MINUTES. OPERATING TIME: 13,149 HOURS, 14 MINUTES. CUTTING TIME: 11,951 HOURS, 15 MINUTES. SPINDLE RUN TIME: 11,598 HOURS, 09 MINUTES. EQUIPPED WITH: OKUMA OSP CNC MAIN OPERATOR DISPLAY INTERFACE W/ MANUAL PULSE GENERATOR JOG WHEEL DIAL. SIMULTANEOUS 4-AXIS TWIN-TURRET CONFIGURATION (UPPER V12 STATION & LOWER V8 STATION). LIVE MILLING AXIS DRIVE CAPABILITIES (M-AXIS INTEGRATION). ATS SYSTEMS ULTIMATE CHUCK UNIT ASSEMBLY (NCSE 265-77, ID.NR. 429360/1 0834, MADE IN GERMANY). RENTSCHLER-REVEN LUFTUNGSSYSTEME GMBH RECOJET MIST FILTER / OIL SEPARATOR COLLECTOR (TYPE: RECOJET 1). MAYFRAN INTERNATIONAL CHIP-TOTE HINGED STEEL BELT CHIP CONVEYOR (MAYFRAN SERIAL NO: KMP-1926-01, MAYFRAN NO: 08M4014). S/N: 142264

2006 MAZAK QTN 450-II CNC TURNING CENTER W/ MAZATROL MATRIX NEXUS CONTROL & JORGENSEN CONVEYOR. SPECIFICATIONS: MODEL: QTN 450-II M [1000U]. CONTROL TYPE: MAZATROL MATRIX NEXUS. CHUCK SIZE CAPABILITY: 12" TO 18". MAXIMUM SWING DIAMETER: 33.268" (845 MM). STANDARD MACHINING DIAMETER: 13.228" (336 MM). MAXIMUM MACHINING DIAMETER: 22.835" (580 MM). BAR WORK CAPACITY: UP TO 4.016" (102 MM). DISTANCE BETWEEN SPINDLE END AND TURRET FACE: 6.664" TO 48.994" (178 MM TO 1243 MM). MAX. SUPPORT WEIGHT (CHUCK WORK): 2,205 LBS (1000 KG). MAX. SUPPORT WEIGHT (SHAFT WORK W/ TAILSTOCK): 2,923 LBS (1326 KG). SPINDLE SPEED RANGE: UP TO 2,000 RPM. NUMBER OF TOOL STATIONS: 12 POSITION INDEXING TURRET. OUTSIDE TURNING TOOL SHANK SIZE: 1.26" SQUARE (32 MM). INSIDE TURNING TOOL BORE SIZE: 2.0" (50 MM). BORING BAR TAPER ID: TOOL I/F MAS BT40 / CAT40. TAILSTOCK CENTER BORE TAPER: BUILT-IN CENTER NO. 5. TAILSTOCK TOTAL TRAVEL STROKE: 40.354" (1025 MM). TAILSTOCK MAXIMUM THRUST CAPACITY: 2,923 LBF (13000 N). X-AXIS TRAVEL STROKE: 13.375" (340 MM). X-AXIS RAPID TRAVERSE RATE: 1,181 IPM (30 M/MIN). Z-AXIS TRAVEL STROKE (1000 BED OPTION): 42.125" (1070 MM). Z-AXIS RAPID TRAVERSE RATE: 1,181 IPM (30 M/MIN). COOLANT TANK CAPACITY: 84.5 GALLONS (320 LITERS). MAIN INPUT VOLTAGE: 3-PHASE AC, 208V, 50/60 HZ. RATED POWER CAPACITY: 60 KVA. MACHINE FOOTPRINT DIMENSIONS (APPROX. LENGTH X WIDTH): 174.29" X 93.94" (4427 MM X 2386 MM). MACHINE OPERATIONAL STRUCTURAL HEIGHT: 80.41" (2042.3 MM). NET BASE MACHINE MASS / WEIGHT: 22,220 LBS (10100 KG). COUNTRY OF MANUFACTURE: MADE IN U.S.A. (FLORENCE, KY). EQUIPPED WITH: MAZATROL MATRIX NEXUS CNC GRAPHIC COMMAND DISPLAY CONTROL CONSOLE DASHBOARD TERMINAL, 12-POCKET HIGH-RIGIDITY RADIAL TOOL INDEXING BLOCK TURRET FACE ASSEMBLY, RENTSCHLER-REVEN LUFTUNGSSYSTEME GMBH REVEN MIST FILTER / INDUSTRIAL AIR CLEANER COLLECTOR UNIT, JORGENSEN CONVEYORS INC HEAVY-DUTY HINGED STEEL BELT CHIP CONVEYOR (SERIAL NO: A-061000-4, DATE: 09-14-06), HEAVY-DUTY PROGRAM-DRIVEN PROGRAMMABLE WORKPIECE SLANTED LATHE TAILSTOCK UNIT ASSEMBLY, INTEGRATED HIGH-FLOW FLUID HEAT TRANSFER EXCHANGER COOLANT TANK RESERVOIR SUBASSEMBLY. S/N: 189113

2007 OKUMA L-470 CNC TURNING CENTER W/ ROYAL FILTERMIST, TURBO CHIP CONVEYOR SN: 130565 SPECIFICATIONS: MODEL: TYPE L-470 (C-SPEC BETWEEN-CENTER DISTANCE: 650) PRODUCED / DATE OF MFG: 07 / 2007 CONTROL TYPE: OKUMA OSP-E100L NO. OF CONTROLLED AXES: 2 (3:M TYPE) SWING OVER BED: 24.41 INCH (620 MM) SWING OVER CROSS-SLIDE: 18.90 INCH (480 MM) DISTANCE BETWEEN CENTERS: 25.59 INCH (650 MM) MAX. TURNING DIAMETER X LENGTH: 16.54 INCH X 25.59 INCH (420 MM X 650 MM) SPINDLE SPEED: 30 - 3,000 MIN1 (1 STEP) SPINDLE NOSE TYPE: JIS A2-11 THROUGH-SPINDLE HOLE DIAMETER: 4.33 INCH (110 MM) SPINDLE BEARING DIAMETER: 5.91 INCH (150 MM) AXIS TRAVEL - X-AXIS: 11.81 INCH (300 MM) [90 MM + 210 MM] AXIS TRAVEL - Z-AXIS: 26.57 INCH (675 MM) FEEDRATE MM/REV (IPR): 0.001 - 1,000.00 (0.00001 - 39.37) RAPID FEEDRATE MM/MIN (IPM) - X-AXIS: 20,000 (787.25) RAPID FEEDRATE MM/MIN (IPM) - Z-AXIS: 25,000 (984.25) TURRET TYPE: V12 NUMBER OF TOOLS: 12 TOOL SIZE - OD TURNING TOOLS: 25 MM X 25 MM (1 INCH X 1 INCH) TOOL SIZE - ID TURNING TOOLS: 40 MM DIAMETER (1-1/2 INCH) ROTARY TOOL SPINDLE SPEED: 200 MIN1 (INFINITELY VARIABLE) SPINDLE DRIVE MOTOR: VAC 22/15 KW (30/20 HP) [30 MIN/CONT.] CARRIAGE FEED MOTOR (Z-AXIS): 6 KW (8 HP) CROSS-SLIDE FEED MOTOR (X-AXIS): 4 KW (5.3 HP) HYDRAULIC POWER UNIT PUMP MOTOR: 2.2 KW (3 HP) GUIDEWAY LUBRICATION PUMP MOTOR: 0.018 KW (0.024 HP) COOLANT PUMP MOTOR: 0.25 KW (0.333 HP) MACHINE HEIGHT: 74.21 INCH (1,885 MM) FLOOR SPACE REQUIRED (WIDTH X DEPTH): 106.30 INCH X 74.80 INCH (2,700 MM X 1,900 MM) NET MASS: 11,880 LBS (5,400 KG) SUPPLY VOLTAGE: 220 / 480 V, 3-PHASE, 60 HZ RATED CAPACITY: 27.7 KVA FULL LOAD CURRENT: 72.7 / 33.4 A LARGEST MOTOR RATE: 114 A INTERRUPTING CAPACITY: 25 / 10 KA DIAGRAM NO: W5201-130-565 MACHINE OPERATING METRICS: RUNNING TIME: 57,704 HOURS OPERATING TIME: 7,264 HOURS CUTTING TIME: 5,663 HOURS SPINDLE RUN TIME: 6,203 HOURS EQUIPPED WITH: OKUMA OSP-E100L CNC CONTROL DASHBOARD WITH INTEGRATED PULSE HANDLE MANUAL DIAL SMX ULTIMATE CHUCK MODULE (NCSE 315-104, ID.NR. 433858/1 0737, MADE IN GERMANY) TURBO SYSTEMS INCORPORATED HINGED BELT STEEL CHIP CONVEYOR (MODEL 5475-8760, SERIAL NO. 376352, MADE IN USA)

2008 OKUMA LU300 M TWIN-TURRET CNC LATHE W/ ATS ULTIMATE CHUCK & REVEN MIST FILTER. MODEL: LU300-M (4-AXIS LIVE TOOLING VARIANT). CONTROL TYPE: OKUMA OSP SERIES. NO. OF CONTROLLED AXES: 4. SWING OVER BED: 20.87" (530 MM). SWING OVER SADDLE (UPPER TURRET): 16.14" (410 MM). SWING OVER SADDLE (LOWER TURRET): 12.60" (320 MM). DISTANCE BETWEEN CENTERS: 23.62" (600 MM). MAX. TURNING DIAMETER X LENGTH: 13.39" X 23.62" (340 MM X 600 MM). SPINDLE NOSE TYPE: JIS A2-8. THROUGH-SPINDLE HOLE DIAMETER: 3.14" (80 MM). SPINDLE BEARING INNER DIAMETER: 4.72" (120 MM). SPINDLE SPEED RANGE: 45 - 4,500 MIN1 (INFINITELY VARIABLE). X-AXIS TRAVEL (UPPER TURRET): 10.24" [70 MM + 190 MM] (260 MM). X-AXIS TRAVEL (LOWER TURRET): 5.51" [30 MM + 110 MM] (140 MM). Z-AXIS TRAVEL (UPPER TURRET): 25.20" (640 MM). Z-AXIS TRAVEL (LOWER TURRET): 24.21" (615 MM). TURRET TYPE (UPPER / LOWER): V12 / V8. NUMBER OF TOTAL TOOL STATIONS: 20 STATIONS (12 UPPER / 8 LOWER). OD TURNING TOOL SHANK SIZE: 1" X 1" (25 MM X 25 MM). ID TURNING TOOL BORE SIZE: 1-1/2" (40 MM DIAMETER). ROTARY TOOL SPINDLE SPEED RANGE: 45 - 4,500 MIN1. SPINDLE DRIVE MOTOR (30 MIN / CONT): VAC 22 / 15 KW (30 / 20 HP). UPPER TURRET AXIS FEED MOTORS: X: 4.0 KW (5.3 HP) / Z: 4.0 KW (5.3 HP). LOWER TURRET AXIS FEED MOTORS: X: 2.2 KW (3.0 HP) / Z: 4.0 KW (5.3 HP). COOLANT PUMP MOTOR: 0.8 KW (1.067 HP). HYDRAULIC POWER UNIT PUMP MOTOR: 2.2 KW (3.0 HP). GUIDEWAY LUBRICATION PUMP MOTOR: 0.018 KW (0.024 HP). REQUIRED MACHINE HEIGHT: 85.67" (2,176 MM). FLOOR SPACE PROFILE (WIDTH X DEPTH): 155.51" X 89.76" (3,950 MM X 2,280 MM). NET MASS OF MACHINE: 14,960 LBS (6,800 KG). SUPPLY VOLTAGE: 220 / 480 V, 3-PHASE, 60 HZ. RATED CAPACITY: 29.9 KVA. FULL LOAD CURRENT: 78.5 / 36.4 A. LARGEST MOTOR AMPERAGE RATE: 96 A. SHORT-CIRCUIT INTERRUPTING CAPACITY: 30 / 10 KA. ELECTRICAL DIAGRAM NO: W5201-139-373. MACHINE OPERATING METRICS: RUNNING TIME: 56,475 HOURS, 46 MINUTES. OPERATING TIME: 12,756 HOURS, 00 MINUTES. CUTTING TIME: 11,771 HOURS, 17 MINUTES. SPINDLE RUN TIME: 11,971 HOURS, 16 MINUTES. EQUIPPED WITH: OKUMA OSP CNC MAIN DISPLAY DASHBOARD TERMINAL W/ MANUAL PULSE GENERATOR HANDWHEEL DIAL. SIMULTANEOUS 4-AXIS TWIN-TURRET CONFIGURATION (UPPER V12 STATION & LOWER V8 STATION). LIVE MILLING AXIS DRIVE CAPABILITIES (M-AXIS INTEGRATION). ATS SYSTEMS ULTIMATE CHUCK UNIT ASSEMBLY (NCSE 265-77, ID.NR. 429360/1 0827, MADE IN GERMANY). RENTSCHLER-REVEN LUFTUNGSSYSTEME GMBH RECOJET MIST FILTER / OIL SEPARATOR COLLECTOR (TYPE: RECOJET 1). S/N: 139373

2005 HAAS VF-3SS SUPER SPEED CNC VMC W/ 12,000 RPM SPINDLE, TSC, PROGRAMMABLE COOLANT. SPECIFICATIONS: MODEL: VF-3SS (SUPER SPEED) DATE OF MFG: 09 / 05 CONTROL TYPE: HAAS AUTOMATION CNC CONTROL X-AXIS TRAVEL: 40.0" (1016 MM) Y-AXIS TRAVEL: 20.0" (508 MM) Z-AXIS TRAVEL: 25.0" (635 MM) SPINDLE NOSE TO TABLE (MIN - MAX): 4.2" - 29.2" (107 MM - 742 MM) TABLE LENGTH: 48.0" (1219 MM) TABLE WIDTH: 18.0" (457 MM) MAX WEIGHT ON TABLE (EQUALLY DISTRIBUTED): 1,750 LBS (794 KG) T-SLOTS WIDTH: 5/8" (16 MM) T-SLOTS CENTER DISTANCE: 4.92" (125 MM) MAX SPINDLE SPEED: 12,000 RPM DRIVE SYSTEM: INLINE DIRECT-DRIVE SPINDLE MOTOR MAX RATING: 30.0 HP (22.4 KW) VECTOR DRIVE MAX TORQUE: 90 FT-LB @ 2,000 RPM SPINDLE TAPER: CAT 40 RAPID TRAVERSE (X, Y, Z AXES): 1,400 IPM (35.6 M/MIN) MAX CUTTING FEEDRATE: 833 IPM (21.2 M/MIN) AXIS THRUST (X, Y AXES): 3,085 LBF (13,723 N) AXIS THRUST (Z AXIS): 3,923 LBF (17,450 N) TOOL CHANGER CAPACITY: 40-STATION CAROUSEL DRUM TYPE MAX TOOL DIAMETER (FULL): 3.0" (76 MM) MAX TOOL WEIGHT: 12 LBS (5.4 KG) TOOL-TO-TOOL TIME (AVERAGE): 1.6 - 2.8 SECONDS CHIP-TO-CHIP TIME (AVERAGE): 2.2 - 3.6 SECONDS VOLTAGE: 208 / 230 VAC PHASE: 3 FREQUENCY: 50 / 60 HZ FULL LOAD AMPERAGE: 80 AMPS LARGEST LOAD AMPERAGE: 70 AMPS SHORT CIRCUIT INTERRUPTING CAPACITY: 10,000 AMPS WIRING DIAGRAM: 93-8100 AIR REQUIRED: 4 SCFM @ 100 PSI (113 L/MIN @ 6.9 BAR) COOLANT CAPACITY: 55 GALLON (208 LITERS) MACHINE WEIGHT: APPROX. 12,500 LBS (5,670 KG) COUNTRY OF MANUFACTURE: MADE IN U.S.A. MACHINE RUN HOURS: SERVO TIME: 12330:55:37 HOURS MOTION TIME: 6769:09:19 HOURS SPINDLE TIME: 7544:16:20 HOURS EQUIPPED WITH: HAAS CNC CONTROL CONSOLE W/ MONITOR SCREEN & MANUAL JOG CONTROL WHEEL THROUGH-SPINDLE COOLANT (TSC) DELIVERY SYSTEM OPTIONS STACK 40-POCKET PERIMETER HIGH-CAPACITY CAROUSEL AUTOMATIC TOOL CHANGER GENUINE HAAS PROGRAMMABLE COOLANT NOZZLE ASSEMBLY HAAS VECTOR DRIVE 40/30 HP CLOSED LOOP POWER MODULE (MODEL: 20-7052) FRONT DOOR SAFETY VIEWING ENCLOSURE SHIELDING EXTERNAL MACHINE STATUS INDICATOR LAMP COLUMN TOWER SIDE-MOUNTED STORAGE ORGANIZER TRAYS (FITTED TO LEFT STRUCTURAL CABINET SHELL) INTERNAL ENCLOSURE MAINTENANCE SAFETY WORK LIGHT BAR S/N: 44029

2006 MAZAK INTEGREX 400-IV MULTI-TASKING LATHE W/ 5-AXIS MILLING HEAD & SUB-SPINDLE SN: 187980 MODEL VARIANT ON PLATE: INTE400-4T CONTROL TYPE: MAZATROL MATRIX SYSTEM INTERFACE DATE OF MFG / ASSEMBLY: 2006-07 MAIN CIRCUIT CONFIGURATION: 3AC 400 V, 50/60 HZ CONTROL CIRCUIT CONFIGURATION: AC 100 V / DC 24 V RATED CAPACITY: 69.3 KVA MACHINE WEIGHT (MASS): 13,100 KG (28,820 LBS) COUNTRY OF MANUFACTURE: MADE IN JAPAN (OGUCHI-CHO, AICHI PREF.) ELEMENTARY DIAGRAM REFERENCE: DD374080002 GENERAL ENVELOPE & AXIS CAPABILITIES: B-AXIS HEAD ROTATION INDEXING RANGE: CONTINUOUS CONTOURING & POSITIONING TILT UPPER MILLING SPINDLE SPINDLE TAPER: CAPTO C6 UPPER MILLING SPINDLE CARRIAGE: FULLY PROGRAMMABLE X, Y, AND Z LINEAR MATRIX LOWER TOOL TURRET: 9-STATION RADIAL DRUM INDEXING CONFIGURATION FOR SIMULTANEOUS TURNING OPERATIONS MAIN LEFT SPINDLE CHUCK BASE: FULL C-AXIS PROGRAMMABLE SPINDLE INDEXING CONFIGURATION RIGHT SUB-SPINDLE CHUCK BASE: FULL PROGRAMMATIC SYNCHRONOUS CONTOUR/TRANSFER CONFIGURATION EQUIPPED WITH: MAZATROL MATRIX CNC GRAPHIC COMMAND DISPLAY CONTROL CONSOLE DASHBOARD TERMINAL HEAVY-DUTY TILTING/LOCKING 5-AXIS B-AXIS ROTARY DRIVEN MILLING SPINDLE HEAD ASSEMBLY LOWER 9-STATION SECONDARY DRUM TURRET BLOCK ASSEMBLY NCSE 315-91 12" HEAVY-DUTY POWER CHUCK ASSEMBLY FRAME (ID.NR. 429366/1 U07, MADE IN GERMANY W/ SAFE JAWS) PROGRAMMABLE RIGHT-SIDE HEAVY-DUTY AUXILIARY SUB-SPINDLE WORKHEAD ALIGNMENT BASE RENISHAW ENCLOSURE INTERIOR MULTI-STATUS OPTICAL WORKPIECE/TOOL RECEIVER SENSING UNIT MAYFRAN CONSEP EXTERNAL MANAGED CONVEYOR & COOLANT FILTRATION SYSTEM (SERIAL NO: 06A3997, SPEC: B6255-08-01-E, VOLTS: 230/460V, 3-PHASE, 60HZ) REAR MOUNTED DUAL HIGH-FLOW FLUID HEAT TRANSFER EXCHANGER COOLANT CIRCULATION PUMP PACKAGE

2007 HAAS TL-15B CNC TURNING CENTER W/ LIVE TOOLING, FULL C-AXIS, TAILSTOCK. MODEL: TL-15 (BIG BORE / LIVE TOOLING / TAILSTOCK CONFIGURATION). MAX SWING OVER SADDLE: 21.65" (550 MM). MAX TURNING DIAMETER: 8.2" (208 MM). MAX TURNING LENGTH: 17.5" (445 MM). MAIN SPINDLE POWER: 30 HP VECTOR DUAL DRIVE SPINDLE SYSTEM. MAIN SPINDLE MAX SPEED: 3,400 RPM. MAIN SPINDLE NOSE: A2-6. BAR CAPACITY: 3.0" (76 MM) "BIG BORE" SPINDLE OPTION. TURRET TYPE: AXIAL INDEXING DISK TYPE TURRET. CAPACITY: 8 STATIONS (SUPPORTS TURNING AND LIVE MILLING DRIVEN TOOLS). LIVE TOOLING SPEED RANGE: 30 - 3,000 RPM. LIVE TOOLING POWER: 5 HP (3.7 KW). X-AXIS TRAVEL: 7.5" (191 MM). Z-AXIS TRAVEL: 17.5" (445 MM). TAILSTOCK CONFIGURATION: PROGRAMMABLE HYDRAULIC POSITIONING BASE WITH QUILL. RAPID TRAVERSE RATES: 710 IPM (18.0 M/MIN). INPUT VOLTAGE REQUIREMENTS: 208 / 230 VAC. PHASE: 3-PHASE. FREQUENCY: 50 / 60 HZ. APPROXIMATE MACHINE WEIGHT: 11,000 LBS (4,990 KG). COUNTRY OF MANUFACTURE: MADE IN U.S.A. (OXNARD, CA). MACHINE RUN HOURS: POWER ON TIME: 11,895 HOURS, 00 MINUTES. CYCLE START TIME: 4,026 HOURS, 45 MINUTES. FEED CUTTING TIME: 2,415 HOURS, 06 MINUTES. M30 TOTAL CYCLE COUNT: 3,133 CYCLES. EQUIPPED WITH: HAAS MAIN OPERATOR CONTROL CONSOLE WITH MANUAL PULSE GENERATOR JOG HANDLE WHEEL DIAL. MUNK POWER CHUCK UNIT ASSEMBLY (MODEL: ZA6-10-75B-02G, SERIAL NO: 113952, CE CERTIFIED). PROGRAMMABLE HYDRAULIC TAILSTOCK. CASTING BED ALIGNMENT ARM. HENNIG MACHINE PROTECTION TELESCOPIC STEEL WAY COVERS (HENNIG JOB NO: 101569, DATE: 4/22). HAAS CLOSED-LOOP VECTOR DUAL DRIVE 40 HP POWER AMPLIFIER MODULE UNIT. AUTOMATIC PARTS CATCHING TRAY RECEIVER DROP ARM MECHANISM ASSEMBLY. S/N: 3078536

2007 HAAS VF-3B CNC VERTICAL MACHINING CENTER W/ GEARED HEAD & RENISHAW PROBING. X-AXIS TRAVEL: 40.0 INCH Y-AXIS TRAVEL: 20.0 INCH Z-AXIS TRAVEL: 25.0 INCH SPINDLE NOSE TO TABLE (MIN-MAX): 4.0 INCH TO 29.0 INCH TABLE SIZE: 48.0 INCH X 18.0 INCH T-SLOT WIDTH: 5/8 INCH MAXIMUM WEIGHT ON TABLE: 3,500 LBS SPINDLE TAPER: CAT 40 SPINDLE SPEED: 0 TO 7,500 RPM DRIVE SYSTEM: 2-SPEED GEARED HEAD SPINDLE MOTOR MAX RATING: 20 HP HAAS VECTOR DRIVE MAX SPINDLE TORQUE: 250 FT-LB @ 450 RPM RAPID TRAVERSE RATE (X/Y/Z): 1,000 IPM MAX CUTTING FEEDRATE: 650 IPM TOOL CHANGER CAPACITY: 40+1 POCKET SIDE-MOUNT TWIN-ARM CHANGER (SMTC) MAX TOOL DIAMETER (FULL POCKETS): 3.5 INCH MAX TOOL WEIGHT: 12 LBS SUPPLY VOLTAGE: 360 - 480 VAC PHASE: 3-PHASE FREQUENCY: 50 / 60 HZ FULL LOAD AMPERAGE: 20 AMPS LARGEST LOAD AMPERAGE: 35 AMPS SHORT CIRCUIT INTERRUPTING CAPACITY: 10,000 AMPS WIRING DIAGRAM NO: 96-0284 AIR REQUIREMENT: 100 PSI @ 4 SCFM MACHINE DIMENSIONS (APPROX): 120 INCH L X 110 INCH W X 105 INCH H MACHINE WEIGHT: APPROXIMATELY 12,500 LBS COUNTRY OF MANUFACTURE: MADE IN U.S.A. POWER ON TIME: 11,962 HOURS, 37 MINUTES CYCLE START TIME: 8,959 HOURS, 44 MINUTES FEED CUTTING TIME: 6,731 HOURS, 32 MINUTES M30 TOTAL CYCLE COUNT: 43,749 CYCLES RIGID TAPPING ENABLED, ENABLE ROTATION AND SCALING ENABLED, THROUGH-SPINDLE COOLANT ENABLED, ENABLE MACRO ENABLED, M19 SPINDLE ORIENTATION ENABLED, ENABLE DNC ENABLED. EQUIPPED WITH: HIGH-CAPACITY 40+1 POCKET SIDE-MOUNT TWIN-ARM AUTOMATIC TOOL CHANGER ASSEMBLY (SMTC), RENISHAW OMP400 WIRELESS WORKPIECE PROBE ASSEMBLY, RENISHAW OMI-SSR OPTICAL MACHINE INTERFACE RECEIVER MODULE, INTEGRATED HIGH-TORQUE 2-SPEED HEADSTOCK GEARBOX ASSEMBLY, THROUGH-SPINDLE COOLANT (TSC) DELIVERY SYSTEM, HAAS VECTOR DRIVE CLOSED-LOOP POWER AMPLIFIER CHASSIS SYSTEM (MODEL 20-HP CLASS), PROGRAMMABLE POSITION MULTI-SEGMENT FLUID COOLANT DELIVERY NOZZLE, SIDE-MOUNTED STORAGE TOOLING ORGANIZER RACK ARRAY. S/N: 1056592

2018 UNIVERSAL LASER SYSTEMS ILS12 PLATFORM CNC LASER CUTTER / ENGRAVER WITH UAC 4000 AIR FILTRATION UNIT S/N: ILS12750DX050718117881 (LASER SYSTEM), UAC4000XXX040118122643 (AIR FILTRATION UNIT) SPECIFICATIONS: LASER MATERIAL PROCESSING AREA: 48" X 24" (1219 X 610 MM) MAXIMUM PART SIZE (W X D X H): 52.5" X 30" X 12" (1334 X 762 X 305 MM) MOTORIZED Z-AXIS TABLE LIFT CAPACITY: 60 LBS (27 KG) ROTARY CAPACITY: 10.25" (260 MM) MAXIMUM DIAMETER OVERALL LASER SYSTEM FOOTPRINT (W X D X H): 69" X 44" X 46" (1753 X 1118 X 1168 MM) LASER SYSTEM WEIGHT: APPROX. 430 LBS (195 KG) CLASS 4 PASS-THROUGH WORK AREA: 24" X INFINITE LENGTH OPEN SIDE PORT ENTRY CLEARANCE: 23.75" X 8" RESOLUTION SELECTION: UP TO 1000 DPI / LPI OPTICS & MOTION: DIGITAL STEPPER MOTORS, ENCLOSED V-GROOVE RAILS, KEVLAR STRUCTURAL BELTS LASER POWER CONFIGURATION: SUPPORTS SINGLE (10 TO 75 WATTS) OR DUAL (UP TO 150 WATTS) LASER CARTRIDGES (RAPID RECONFIGURATIONTM) ELECTRICAL POWER REQUIREMENTS: SINGLE-PHASE 220V240V AC, 50/60 HZ, 1016 AMPS EXHAUST COLLECTOR PORTS: DUAL 4" OD FITTINGS ON REAR CHASSIS LASER MANUFACTURE DATE: MAY 2018 EQUIPPED WITH: UNIVERSAL LASER SYSTEMS UAC 4000 ADVANCED AIR FILTRATION UNIT (SN: UAC4000XXX040118122643, MANUFACTURED: APRIL 2018, 4-STAGE ACTIVE FILTRATION SYSTEM, MOBILE ON CASTERS)

ASSORTED CAPTO C6 TOOL HOLDERS & BORING BARS

2013 BROWN & SHARPE GLOBAL PERFORMANCE 5-7-5 COORDINATE MEASURING MACHINE, RENISHAW PH10M PROBING. X-AXIS MEASURING RANGE (STROKES): 500 MM (19.7 IN) Y-AXIS MEASURING RANGE (STROKES): 700 MM (27.6 IN) Z-AXIS MEASURING RANGE (STROKES): 500 MM (19.7 IN) OVERALL WIDTH: 1,024 MM (40.3 IN) OVERALL LENGTH: 1,455 MM (57.3 IN) OVERALL HEIGHT: 2,540 MM (100.0 IN) MAXIMUM PART WEIGHT CAPACITY: 625 KG (1,377 LBS) APPROXIMATE MACHINE WEIGHT: 800 KG (1,763 LBS) MAXIMUM 3D POSITIONING SPEED: 520 MM/S MAXIMUM 3D ACCELERATION: 1,730 MM/S2 VOLUMETRIC ACCURACY FORMULA: 2.5 + (3.3L / 1000) MICRONS OPTIMAL OPERATING TEMPERATURE: 18C TO 22C (20C +/- 2C BASELINE) MINIMUM AIR SUPPLY PRESSURE: 5.5 BAR (APPROX. 80 PSI) AIR CONSUMPTION: 73.5 NL/MIN EQUIPPED WITH: HEXAGON MANUAL JOGBOX CONTROLLER RENISHAW PH10M MOTORIZED PROBE HEAD SYSTEM S/N: 0613-1133 UA

2004 OKUMA CAPTAIN-L470 CNC TURNING CENTER W/ ROYAL FILTERMIST & SCHUNK CHUCK. SPECIFICATIONS : MODEL: CAPTAIN-L470 DATE OF MFG: 12 / 2004 CONTROL TYPE: OKUMA OSP-E100L CORE INTERFACE NUMBER OF CONTROLLED AXES: 2-AXIS TURNING PLATFORM ARCHITECTURE SWING OVER BED: 24.41" (620 MM) SWING OVER CROSS-SLIDE: 18.90" (480 MM) MAXIMUM TURNING DIAMETER X LENGTH ENVELOPE: 16.54" X 12.99" (420 MM X 330 MM) SPINDLE NOSE TYPE: JIS A2-11 THROUGH-SPINDLE HOLE DIAMETER: 4.33" (110 MM) SPINDLE BEARING INSIDE DIAMETER: 5.91" (150 MM) SPINDLE TAPER HOLE PROFILE: MT NO. 5 SPINDLE SPEED RANGE: 30 ~ 3,000 RPM (INFINITELY VARIABLE 1-STEP SETUP) NUMBER OF TURRET TOOL POSITIONS: 12-STATION V12 DISK TURRET OD TURNING TOOL SHANK SIZE: 1.0" SQUARE (25 MM X 25 MM) ID TURNING TOOL BORE SIZE: 1.50" (40 MM) X-AXIS TRAVEL STROKE: 11.81" [90 MM + 210 MM] (300 MM) X-AXIS FEEDRATE COMMAND INCREMENTS: 0.001 TO 1,000.00 MM/REV X-AXIS RAPID TRAVERSE RATE: 787.25 IPM (20,000 MM/MIN) Z-AXIS TRAVEL STROKE (650 BED OPTION): 26.57" (675 MM) Z-AXIS FEEDRATE COMMAND INCREMENTS: 0.001 TO 1,000.00 MM/REV Z-AXIS RAPID TRAVERSE RATE: 984.25 IPM (25,000 MM/MIN) TAILSTOCK QUILL INTERNAL TAPER PROFILE: MT NO. 5 (MORSE TAPER 5) TAILSTOCK QUILL TRAVEL / STROKE: 5.91" (150 MM) TAILSTOCK BODY TOTAL TRAVEL: 20.28" (515 MM) MAIN SPINDLE DRIVE MOTOR (20 MIN/CONTINUOUS RATING): 30 / 20 HP (22 / 15 KW) X-AXIS FEED DRIVE MOTOR: 4 HP (3.0 KW) Z-AXIS FEED DRIVE MOTOR: 5.3 HP (4.0 KW) HYDRAULIC POWER UNIT PUMP MOTOR: 3 HP (2.2 KW) GUIDEWAY LUBRICATION PUMP MOTOR: 0.024 HP (0.018 KW) COOLANT PUMP MOTOR: 0.333 HP (0.25 KW) FOR SIDE DISPOSAL SETUP SUPPLY CONNECTION CONFIGURATION: 220 / 480 V, 3-PHASE, 60 HZ RATED POWER CAPACITY: 29.5 KVA FULL LOAD CURRENT LOAD: 77.5 / 35.5 A LARGEST MOTOR AMPERAGE DRAW: 114 A SHORT-CIRCUIT INTERRUPTING CAPACITY: 25 / 10 KA ELECTRICAL DIAGRAM SHEET REFERENCE: W5201-112-611 MACHINE BASE PHYSICAL HEIGHT: 74.21" (1,885 MM) FLOOR SPACE REQUIREMENT DIMENSIONS (LENGTH X WIDTH): 106.30" X 74.80" (2,700 MM X 1,900 MM) NET BASE MACHINE STRUCTURAL WEIGHT: 11,440 LBS (5,200 KG) COUNTRY OF MANUFACTURE: MADE IN JAPAN (OKUMA CORPORATION, AICHI PREFECTURE) MACHINE OPERATING HOUR DIAGNOSTICS (LOGGED VIA OSP-E100L OPERATING REPORT HMI PANEL): TOTAL RUNNING LOG COUNTER: 74,640 HOURS, 40 MINUTES ACTIVE PRODUCTION OPERATING TIME: 29,140 HOURS, 22 MINUTES ACTIVE CUTTING FEED INTERVAL: 26,771 HOURS, 23 MINUTES NON-OPERATIONAL/SETUP IDLE PERIOD: 45,500 HOURS, 18 MINUTES SPINDLE ROTATION RUNNING LOG TIME: 26,774 HOURS, 42 MINUTES EQUIPPED WITH: OKUMA OSP-E100L CNC CONTROL DASHBOARD WITH CRT GRAPHIC LAYOUT AND FULL ALPHANUMERIC INPUT KEYPAD SCHUNK 12" 3-JAW QUICK-CHANGE POWER CHUCK (MODEL: NCSE 315-91, ID.NR. 429368/1 T06, MADE IN GERMANY) 12-STATION HIGH-RIGIDITY V12 AXIAL TOOL TURRET HEAD ASSEMBLY ROYAL FILTERMIST CENTRIFUGAL OIL MIST AIR COLLECTOR UNIT (MODEL: FX-900, SERIAL NO: FX900-001877) TURBO SYSTEMS INCORPORATED HEAVY-DUTY HINGED BELT LIFT-UP CHIP CONVEYOR SYSTEM (MODEL: 5475-8760, SERIAL NO: 36725) S/N: 112611

2004 HAAS VF-3SS SUPER SPEED CNC VERTICAL MACHINING CENTER W/ 12,000 RPM, TSC. X-AXIS TRAVEL: 40.0" (1016 MM) Y-AXIS TRAVEL: 20.0" (508 MM) Z-AXIS TRAVEL: 25.0" (635 MM) SPINDLE NOSE TO TABLE (MIN - MAX): 4.2" - 29.2" (107 MM - 742 MM) TABLE LENGTH: 48.0" (1219 MM) TABLE WIDTH: 18.0" (457 MM) MAX WEIGHT ON TABLE (EQUALLY DISTRIBUTED): 1,750 LBS (794 KG) T-SLOTS WIDTH: 5/8" (16 MM) T-SLOTS CENTER DISTANCE: 4.92" (125 MM) MAX SPINDLE SPEED: 12,000 RPM DRIVE SYSTEM: INLINE DIRECT-DRIVE SPINDLE MOTOR MAX RATING: 30.0 HP (22.4 KW) HAAS VECTOR DRIVE MAX TORQUE: 90 FT-LB @ 2,000 RPM SPINDLE TAPER: CAT 40 RAPID TRAVERSE (X, Y, Z AXES): 1,400 IPM (35.6 M/MIN) MAX CUTTING FEEDRATE: 833 IPM (21.2 M/MIN) AXIS THRUST (X, Y AXES): 3,085 LBF (13,723 N) AXIS THRUST (Z AXIS): 3,923 LBF (17,450 N) TOOL CHANGER CAPACITY: 24+1 POSITION SIDE-MOUNT TOOL CHANGER (SMTC) MAX TOOL DIAMETER (FULL): 3.0" (76 MM) MAX TOOL WEIGHT: 12 LBS (5.4 KG) TOOL-TO-TOOL TIME (AVERAGE): 1.6 - 2.8 SECONDS CHIP-TO-CHIP TIME (AVERAGE): 2.2 - 3.6 SECONDS VOLTAGE INPUT: 208 / 230 VAC PHASE: 3-PHASE FREQUENCY: 50 / 60 HZ FULL LOAD AMPERAGE: 80 AMPS LARGEST LOAD AMPERAGE: 70 AMPS SHORT CIRCUIT INTERRUPTING CAPACITY: 10,000 AMPS WIRING DIAGRAM NO: 93-8100 AIR REQUIRED: 4 SCFM @ 100 PSI (113 L/MIN @ 6.9 BAR) COOLANT TANK CAPACITY: 55 GALLON (208 LITERS) MACHINE WEIGHT: APPROX. 12,500 LBS (5,670 KG) COUNTRY OF MANUFACTURE: MADE IN U.S.A. (OXNARD, CA) MACHINE OPERATING METRICS: SERVO TIME: 21,961 HOURS, 58 MINUTES MOTION TIME: 12,685 HOURS, 14 MINUTES SPINDLE TIME: 12,023 HOURS, 48 MINUTES EQUIPPED WITH: HAAS CNC CONTROL INTERFACE CONSOLE WITH MANUAL JOG DIAL WHEEL THROUGH-SPINDLE COOLANT (TSC) SYSTEM UPGRADES ARRAY 24+1 POCKET SIDE-MOUNT HIGH-SPEED AUTOMATIC TOOL CHANGER CAROUSEL HAAS VECTOR DRIVE CLOSED-LOOP POWER AMPLIFIER MODULE (40/30 HP PEAK, MODEL 20-7052) PROGRAMMABLE COOLANT NOZZLE ADJUSTMENT BLOCK ASSEMBLY HEAVY-DUTY SIDE STORAGE ORGANIZATIONAL SHELVING (MOUNTED ON LEFT SIDE PANEL) DUAL FRONT SLIDING ACCESS DOORS WITH SAFETY POLYCARBONATE ENCLOSURE WINDOWS INTERIOR ENCLOSURE SAFETY HALOGEN/LED WORK LIGHT ASSEMBLY EXTERNAL ELECTRICAL DISCONNECT SWITCH HUB FRAME MOUNT (480 VOLTS PANEL RATED COMPONENT) S/N: 36021

2005 HAAS VF-3SS SUPER SPEED CNC VERTICAL MILL W/ SIDE-MOUNT TOOL CHANGER & ACCU-LUBE. SPECIFICATIONS: MODEL: VF-3SS (SUPER SPEED) DATE OF MFG: 11 / 05 X-AXIS TRAVEL: 40.0" (1016 MM) Y-AXIS TRAVEL: 20.0" (508 MM) Z-AXIS TRAVEL: 25.0" (635 MM) SPINDLE NOSE TO TABLE (MIN - MAX): 4.2" - 29.2" (107 MM - 742 MM) TABLE LENGTH: 48.0" (1219 MM) TABLE WIDTH: 18.0" (457 MM) MAX WEIGHT ON TABLE (EQUALLY DISTRIBUTED): 1,750 LBS (794 KG) T-SLOTS WIDTH: 5/8" (16 MM) T-SLOTS CENTER DISTANCE: 4.92" (125 MM) MAX SPINDLE SPEED: 12,000 RPM DRIVE SYSTEM: INLINE DIRECT-DRIVE SPINDLE MOTOR MAX RATING: 30.0 HP (22.4 KW) VECTOR DRIVE MAX TORQUE: 90 FT-LB @ 2,000 RPM SPINDLE TAPER: CAT 40 RAPID TRAVERSE (X, Y, Z AXES): 1,400 IPM (35.6 M/MIN) MAX CUTTING FEEDRATE: 833 IPM (21.2 M/MIN) AXIS THRUST (X, Y AXES): 3,085 LBF (13,723 N) AXIS THRUST (Z AXIS): 3,923 LBF (17,450 N) TOOL CHANGER CAPACITY: 24+1 POSITION SIDE-MOUNT (SMTC) MAX TOOL DIAMETER (FULL): 3.0" (76 MM) MAX TOOL WEIGHT: 12 LBS (5.4 KG) TOOL-TO-TOOL TIME (AVERAGE): 1.6 - 2.8 SECONDS CHIP-TO-CHIP TIME (AVERAGE): 2.2 - 3.6 SECONDS VOLTAGE: 208 / 230 VAC PHASE: 3 FREQUENCY: 50 / 60 HZ FULL LOAD AMPERAGE: 80 AMPS LARGEST LOAD AMPERAGE: 70 AMPS SHORT CIRCUIT INTERRUPTING CAPACITY: 10,000 AMPS WIRING DIAGRAM: 93-8100 AIR REQUIRED: 4 SCFM @ 100 PSI (113 L/MIN @ 6.9 BAR) COOLANT CAPACITY: 55 GALLON (208 LITERS) MACHINE WEIGHT: APPROX. 12,500 LBS (5,670 KG) COUNTRY OF MANUFACTURE: MADE IN U.S.A. MACHINE RUN HOURS: SERVO TIME: 941:40:50 HOURS MOTION TIME: 151:09:06 HOURS SPINDLE TIME: 135:22:36 HOURS EQUIPPED WITH: HAAS CNC CONTROL PANEL INTERFACE W/ JOG HANDWHEEL 24+1 STATION SIDE-MOUNT AUTOMATIC TOOL CHANGER ASSEMBLY ACCU-LUBE MINIMAL QUANTITY LUBRICATION / PRECISION APPLICATOR SYSTEM ENCLOSED WORK COMPARTMENT LIGHT BAR 4TH AXIS READY (INTERNAL BRUSH-TYPE DRIVE BOARD AND WIRING HARNESS PRE-INSTALLED NOTE: 4TH AXIS ROTARY TABLE UNIT IS NOT INCLUDED) S/N: 45619

2004 OKUMA LB35II-M CNC TURNING CENTER W/ LIVE TOOLING, ROYAL FILTERMIST SN: 113364 SPECIFICATIONS MODEL: LB35II-M (LIVE TOOLING CONFIGURATION) PRODUCED/DATE OF MFG: 2004.12 CONTROL TYPE: OKUMA OSP-P100L SWING OVER BED: 27.56 INCH (700 MM) SWING OVER CARRIAGE: 16.93 INCH (430 MM) DISTANCE BETWEEN CENTERS: 59.05 INCH (1,570 MM) MAX. TURNING DIAMETER X LENGTH: 18.11 INCH X 59.03 INCH (460 MM X 1,500 MM) X-AXIS TRAVEL: 12.99 INCH (330 MM) Z-AXIS TRAVEL: 61.81 INCH (1,570 MM) SPINDLE SPEED RANGE: 14 - 3,200 RPM THROUGH-SPINDLE HOLE DIAMETER: 3.54 INCH (90 MM) SPINDLE BEARING INNER DIAMETER: 5.12 INCH (130 MM) TURRET TYPE: V12 (M-TOOLS) NUMBER OF TOOLS: 12 LIVE TOOLING OD TURNING SHANK SIZE: 1 INCH (25 MM SQUARE) LIVE TOOLING ID TURNING BORE SIZE: 1.97 INCH (50 MM) TURRET INDEX TIME: 0.3 SECONDS / STATION M-TOOL SPINDLE SPEED: INFINITELY VARIABLE UP TO 2,000 RPM RAPID TRAVERSE RATES: X-AXIS: 590.55 IPM (15,000 MM/MIN) / Z-AXIS: 787.40 IPM (20,000 MM/MIN) TAILSTOCK SPINDLE DIAMETER: 4.72 INCH (120 MM) TAILSTOCK SPINDLE TAPER HOLE: MT NO.5 (BUILT-IN) TAILSTOCK SPINDLE TRAVEL: 6.69 INCH (170 MM) SPINDLE DRIVE MOTOR: VAC 30/20 KW (40/27 HP) MACHINE WEIGHT: APPROX. 25,740 LBS (11,700 KG) FLOOR SPACE REQUIRED: 191.54 INCH X 105.51 INCH (4,865 MM X 2,680 MM) ELECTRICAL REQUIREMENTS: 220/480V, 3-PHASE, 60HZ, 38.5 KVA MACHINE OPERATING METRICS: RUNNING TIME: 43,211 HOURS OPERATING TIME: 16,001 HOURS CUTTING TIME: 14,523 HOURS SPINDLE RUN TIME: 4,196 HOURS EQUIPPED WITH: OKUMA OSP-P100L CNC CONTROL PANEL W/ PULSE GENERATOR HANDWHEEL LIVE TOOLING (M-AXIS CAPABILITIES) SMX ULTIMATE CHUCK UNIT (NCSE 400-128, MADE IN GERMANY) ROYAL FILTERMIST FX-1200 CENTRIFUGAL MIST COLLECTOR / AIR FILTRATION UNIT (MODEL FX-1200) ENAMOTO BEA CO. HINGED STEEL BELT CHIP CONVEYOR (MODEL LB35-2-850H, SERIAL: E00532) FOOT SWITCH LATHE CHUCK CONTROLLER PEDAL 3-COLOR STATUS INDICATOR TOWER LIGHT

LARGE QTY ASSORTED LATHE CHUCK JAWS (SCHUNK & OTHER) - BIG LOT OF HARD/SOFT CHUCK JAWS PULLED FROM CNC LATHE TOOLING CRIBS, INCLUDING SCHUNK GBK-630 AND GBK-350 STAMPED JAW SETS WITH ID TAGS. MIXED SIZES AND STYLES

HAAS HRT210 CNC ROTARY TABLE, 210 MM (8.3") WITH 8" 3-JAW MANUAL SCROLL CHUCK. MODEL: HRT210 (P1 STANDARD BRUSHLESS/BRUSH VARIANT PLATFORM). PLATTER DIAMETER BASE: 8.30" (210 MM). CENTER HEIGHT: 6.00" (152.4 MM). CHUCK SIZE INSTALLED: 8" (200 MM) THREE-JAW SCROLL CHUCK. CHUCK MODEL FAMILY: SANOU K11-200. INTERFACE CABLING: HEAVY-DUTY BRAIDED CONDUIT DUAL-LINE SERVO CABLE HARNESS. CONNECTOR CONFIGURATIONS: STANDARD HAAS MULTI-PIN CIRCULAR MILITARY-STYLE PLASTIC/RUBBER SERVO PLUGS. MADE IN U.S.A. (OXNARD, CA). EQUIPPED WITH: SANOU K11-200 8" 3-JAW MANUAL SCROLL CHUCK WITH REVERSIBLE TOP HARD JAW SEGMENTS, HEAVY-DUTY INTEGRATED T-SLOT INDEXING PLATTER BASE RING, REAR FACE MOTOR HOUSING ENCLOSURE, PROTECTIVE GUARD CASTING BLOCK, DUAL-CONNECTOR COMMUNICATION/POWER CABLING MATRIX FOR MAIN AXIS INTEGRATION. S/N: 227441 P1

2013 NIKKEN 5AX201 CNC 5-AXIS TILTING ROTARY TABLE PRECISION FACEPLATE LAYOUT WITH INTEGRATED ALIGN T-SLOTS DRIVE ARCHITECTURE: HEAVY-DUTY ALPHA SERVO DUAL-AXIS INTEGRATION SYSTEM MADE IN JAPAN S/N: 3651

2002 OKUMA CAPTAIN L370 CNC TURNING CENTER, SMW ULTIMATE CHUCK, ROYAL MIST COLLECTOR, TURBO CONVEYOR S/N: 0486 / 101579 MAX SWING OVER BED: 20.87 INCH (530 MM) MAX SWING OVER CARRIAGE: 20.87 INCH (530 MM) MAX SWING OVER CROSS-SLIDE: 16.54 INCH (420 MM) MAX TURNING DIAMETER: 14.57 INCH (370 MM) / [13.39 INCH (340 MM) M TYPE] MAX TURNING LENGTH: 9.84 INCH (250 MM) SPINDLE NOSE: JIS A2-6 SPINDLE BORE DIAMETER (THROUGH-HOLE): 2.44 INCH (62 MM) SPINDLE TAPER HOLE: 2.75 INCH (70 MM) X 1/10 SPINDLE DIAMETER: 3.94 INCH (100 MM) SPINDLE SPEED RANGE: 45 - 4,500 RPM SPINDLE SPEED RANGES: 1 STEP SPINDLE MOTOR POWER: 20 HP (15 KW) 20 MIN / 15 HP (11 KW) CONTINUOUS X-AXIS TRAVEL (CROSS): 10.24 INCH (260 MM) / [2.95 INCH + 7.28 INCH (75 MM + 185 MM)] Z-AXIS TRAVEL (LONGITUDINAL): 20.47 INCH (520 MM) X-AXIS RAPID TRAVERSE RATE: 787 IPM (20 M/MIN) Z-AXIS RAPID TRAVERSE RATE: 984 IPM (25 M/MIN) CUTTING FEED RANGE (X & Z): 0.00001 - 39.37 IPR (0.001 - 1,000.00 MM/REV) TURRET TYPE: V12 TURRET CAPACITY: 12 STATIONS TOOL SIZE (SQUARE/OD): 1.00 INCH (25 MM) TOOL SIZE (BORING BAR/ID MAX): 1.50 INCH (40 MM) ROTARY TOOL SPINDLE SPEED: 45 - 4,500 RPM (INFINITELY VARIABLE) C-AXIS CONTROL ANGLE: 360 (0.001 INCREMENT) C-AXIS RAPID TRAVERSE RATE: 200 RPM Z-AXIS FEED MOTOR POWER: 5.3 HP (4 KW) X-AXIS FEED MOTOR POWER: 4 HP (3 KW) HYDRAULIC POWER UNIT MOTOR: 3 HP (2.2 KW) GUIDEWAY LUBRICATION PUMP MOTOR: 0.024 HP (0.018 KW) COOLANT PUMP MOTOR: 0.333 HP (0.25 KW) SIDE DISPOSAL / 1.067 HP (0.8 KW) REAR DISPOSAL FLOOR SPACE DIMENSIONS: 86.61"L X 67.72"W X 68.70"H MACHINE NET WEIGHT: 8,800 LBS (4,000 KG) STANDARD / 9,020 LBS (4,100 KG) M TYPE EQUIPPED WITH: OKUMA OSP-E100L SMX ULTIMATE CHUCK 265MM 3 JAW TURBO SYSTEM INCORPORATED CHIP CONVEYOR (SERIAL NO. 359569 / PART NO. 5475-8466) ROYAL PRODUCTS MIST COLLECTOR (SERIAL NO. 6-5048, SERIES 8, PATENT NO. 4,152,128)

2001 HAAS VF-3B VERTICAL MILL W/ 2-SPEED GEARED-HEAD SPINDLE, 20HP VECTOR DRIVE, 40 ATC. SPECIFICATIONS: MODEL: VF-3B X-AXIS TRAVEL: 40" Y-AXIS TRAVEL: 20" Z-AXIS TRAVEL: 25" SPINDLE NOSE TO TABLE SURFACE: 4" - 29" TABLE LENGTH: 48" TABLE WIDTH: 18" MAX WEIGHT ON TABLE: 3,500 LBS T-SLOT WIDTH: 5/8" SPINDLE SPEED: 0 - 7,500 RPM DRIVE SYSTEM: 2-SPEED GEARED-HEAD SPINDLE POWER: 20 HP SPINDLE TAPER: CAT 40 MAX TORQUE: 90 FT-LB @ 450 RPM TOOL CAPACITY: 40-STATION TOOL CHANGER CAROUSEL MAX TOOL DIAMETER: 3.5" MAX TOOL WEIGHT: 12 LBS RAPID TRAVERSE RATES (X/Y/Z): 1,000 IPM MAX CUTTING FEEDRATE: 650 IPM SERIAL NUMBER: 25768 DATE OF MFG: 06 / 01 VOLTAGE: 208/230 PHASE: 3 HERTZ: 50/60 FULL LOAD: 40 AMPS LARGEST LOAD: 30 AMPS SHORT CIRCUIT INTERRUPTING CAPACITY: 10,000 AMPS WIRING DIAGRAM: 968000 MACHINE WEIGHT: APPROX. 12,500 LBS COUNTRY OF MANUFACTURE: MADE IN U.S.A. MACHINE RUN HOURS: SERVO TIME: 19209:03:07 HOURS MOTION TIME: 347:21:40 HOURS SPINDLE TIME: 1850:30:30 HOURS EQUIPPED WITH: HAAS CNC CONTROL PANEL W/ JOG HANDLE FACTORY TWO-SPEED GEARED-HEAD SPINDLE SYSTEM 4TH AXIS READY (INTERNAL BRUSH-TYPE DRIVE BOARD AND WIRING HARNESS PRE-INSTALLED) PROGRAMMABLE COOLANT NOZZLE (P-COOL) BRUSHLESS SERVOS HIGH-SPEED MACHINING (HSM) MACRO CODE COORDINATE SCALING RIGID TAP 1MB EXPANDED MEMORY CONFIGURATION QUICK CODE EGS HEVI-DUTY SHIELDED GENERAL PURPOSE TRANSFORMER (CATALOG NO. T21115S, 15 KVA, 3 PHASE, 60 HERTZ, H.V. 480 DELTA, L.V. 208Y/120, WEIGHT 173 LBS.) CUTLER-HAMMER HEAVY DUTY SAFETY SWITCH DISCONNECT BOX S/N: 25768

2001 HAAS VF-3B VERTICAL MILL W/ 2-SPEED GEARED-HEAD SPINDLE, 20HP VECTOR DRIVE, 40 ATC. SPECIFICATIONS: MODEL: VF-3B X-AXIS TRAVEL: 40" Y-AXIS TRAVEL: 20" Z-AXIS TRAVEL: 25" SPINDLE NOSE TO TABLE SURFACE: 4" - 29" TABLE LENGTH: 48" TABLE WIDTH: 18" MAX WEIGHT ON TABLE: 3,500 LBS T-SLOT WIDTH: 5/8" SPINDLE SPEED: 0 - 7,500 RPM DRIVE SYSTEM: 2-SPEED GEARED-HEAD (HIGH TORQUE VECTOR DRIVE) SPINDLE POWER: 20 HP SPINDLE TAPER: CAT 40 MAX TORQUE: 90 FT-LB @ 450 RPM TOOL CAPACITY: 40-STATION TOOL CHANGER CAROUSEL MAX TOOL DIAMETER: 3.5" MAX TOOL WEIGHT: 12 LBS RAPID TRAVERSE RATES (X/Y/Z): 1,000 IPM MAX CUTTING FEEDRATE: 650 IPM SERIAL NUMBER: 25890 DATE OF MFG: 06 / 01 VOLTAGE: 208/230 PHASE: 3 HERTZ: 50/60 FULL LOAD: 40 AMPS LARGEST LOAD: 30 AMPS SHORT CIRCUIT INTERRUPTING CAPACITY: 10,000 AMPS WIRING DIAGRAM: 968000 MACHINE WEIGHT: APPROX. 12,500 LBS COUNTRY OF MANUFACTURE: MADE IN U.S.A. MACHINE RUN HOURS: SERVO TIME: 21852:19:03 HOURS MOTION TIME: 3366:03:23 HOURS SPINDLE TIME: 3909:35:41 HOURS EQUIPPED WITH: HAAS CNC CONTROL PANEL W/ JOG HANDLE FACTORY TWO-SPEED GEARED-HEAD SPINDLE SYSTEM 4TH AXIS READY (INTERNAL BRUSH-TYPE DRIVE BOARD AND WIRING HARNESS PRE-INSTALLED) PROGRAMMABLE COOLANT NOZZLE (P-COOL) BRUSHLESS SERVOS HIGH-SPEED MACHINING (HSM) MACRO CODE COORDINATE SCALING RIGID TAP 1MB EXPANDED MEMORY CONFIGURATION QUICK CODE EGS HEVI-DUTY SHIELDED GENERAL PURPOSE TRANSFORMER (CATALOG NO. T21115S, 15 KVA, 3 PHASE, 60 HERTZ, H.V. 480 DELTA, L.V. 208Y/120, WEIGHT 173 LBS.) CUTLER-HAMMER HEAVY DUTY SAFETY SWITCH DISCONNECT BOX S/N: 25890

ASSORTED CAPTO C6 TOOL HOLDERS AND TOOLING

DONALDSON TORIT DOWNFLO OVAL DFO2-8QD DUST COLLECTOR - 7.5 HP, 8-FILTER, 1,520 SQ FT MEDIA AREA. BRAND/MANUFACTURER: DONALDSON COMPANY, INC. (TORIT) MODEL NO: DOWNFLO OVAL (DFO2-8QD) EQUIPMENT TYPE: DOWNFLOW CARTRIDGE DUST COLLECTOR MOTOR HORSEPOWER: 7.5 HP ELECTRICAL REQUIREMENTS: 208-460V / 60 HZ / 3-PHASE FILTER TECHNICAL DETAILS: 2 MODULES WIDE CONTAINING A TOTAL OF 8 OVAL CARTRIDGE FILTERS (FILTER PART NO: P191889) FEATURING ULTRA-WEB NANOFIBER TECHNOLOGY. TOTAL FILTER MEDIA AREA: 1,520 SQUARE FEET PERFORMANCE CAPACITY: 760 - 6,380 CFM RANGE CAPACITY (NOMINAL AIRFLOW ~3,000 - 4,000 CFM WITH 7.5 HP MOTOR) CLEANING SYSTEM: AUTOMATIC REVERSE PULSE-JET SYSTEM

HAAS HRT210SHS HIGH-SPEED CNC SERVO ROTARY TABLE, 210 MM (8.27") SPECIFICATIONS: MODEL: HRT210SHS (HIGH-SPEED SERVO VARIANT) PLATTER DIAMETER: 8.30" (210 MM) CENTER HEIGHT: 6.00" (152.4 MM) PLATTER BOLT PATTERN: 6 T-SLOTS ORIENTED AT 60 DEGREES THROUGH-BORE DIAMETER: 2.00" (50.8 MM) INTERNAL MECHANICAL LAYOUT: DIRECT-COUPLED ZERO-BACKLASH HARMONIC DRIVE (NO WORM GEARS) MAXIMUM ROTATION SPEED: UP TO 300 DEGREES / SECOND MINIMUM PROGRAMMABLE STEP RESOLUTION: 0.001 DEGREE MAX ROTATION PER SINGLE MOVE INSTRUCTION: 999.999 DEGREES CONTINUOUS DRIVE TORQUE: 65 FT-LB (88 NM) INTERNAL AIR BRAKE HOLDING TORQUE: 40 FT-LB @ 40 PSI (54 NM @ 2.8 BAR) MAXIMUM PLATTER RADIAL / AXIAL RUNOUT: 0.0005" (0.013 MM) INDEXING ACCURACY: +/-45 ARC-SEC REPEATABILITY: 10 ARC-SEC CHUCK SIZE & ORIGIN: 10" (250 MM) SCROLL CHUCK, STAMPED "MADE IN POLAND" CHUCK MODEL SERIES: 3565-10" CHUCK MAX ROTATION RATING: 2,500 RPM (NMAX = 2500 1/MIN) INTERFACE CABLING: HEAVY-DUTY BRAIDED CONDUIT DUAL-CONNECTOR WIRING HARNESS COUNTRY OF MANUFACTURE: MADE IN U.S.A. (OXNARD, CA) EQUIPPED WITH: MADE IN POLAND 10" 3-JAW MANUAL SCROLL CHUCK WITH REVERSIBLE TOP HARD JAWS INTEGRATED HEAVY-DUTY T-SLOT INDEXING PLATTER BASE RING (6 T-SLOTS AT 60 DEGREES) INTERNAL ZERO-BACKLASH HARMONIC DRIVE SYSTEM INTEGRATION INTEGRATED INTERNAL PNEUMATIC AIR BRAKE CLAMPING ASSEMBLY RIGID REAR FACE MOTOR HOUSING PROTECTIVE GUARD CASTING ENCLOSURE DUAL-LINE CIRCULAR CONTROL INTERFACE SERVO MOTOR COMMUNICATION POWER CABLING S/N: 250059

HAAS HRT210 CNC ROTARY TABLE, 210 MM (8.3") W/ 3-JAW CHUCK. MODEL: HRT210 (P1 AC BRUSHLESS SIGMA-1 SYSTEM ARCHITECTURE) PLATTER DIAMETER: 8.30" (210 MM) MAX WEIGHT ON PLATTER (SUPPORTED): 170 LB (77.1 KG) MAX WEIGHT ON PLATTER (UNSUPPORTED): 85 LB (38.6 KG) STANDARD T-SLOTS: 6 POSITIONED AT 60 MAX TORQUE: 210 FT-LB MAX SPEED: 100 / SEC INDEXING ACCURACY: 15 ARC-SEC REPEATABILITY: 10 ARC-SEC BACKLASH: PRECISION WORM GEAR DRIVE WITH MINIMAL PLAY MOTOR CONNECTION: P1 CONFIGURATION (AC BRUSHLESS) BRAKE TYPE: PNEUMATIC CLAMP REQUIRING STANDARD FACTORY AIR LINES (~100 PSI) CHUCK CONFIGURATION: 3-JAW MANUAL SCROLL CHUCK CHUCK JAW STYLE: MACHINE-CONTOURED STEP SOFT JAWS INTERFACE CABLING: HEAVY-DUTY BRAIDED CONDUIT DUAL-LINE SERVO CABLE HARNESS CONNECTOR CONFIGURATIONS: STANDARD HAAS MULTI-PIN CIRCULAR MILITARY-STYLE PLASTIC/RUBBER SERVO PLUGS COUNTRY OF MANUFACTURE: MADE IN U.S.A. (OXNARD, CA) EQUIPPED WITH: 3-JAW MANUAL SCROLL CHUCK FACE-MOUNTED W/ CUSTOM CONTOURED MACHINE SOFT JAWS INTEGRATED HEAVY-DUTY T-SLOT INDEXING PLATTER BASE RING (6 T-SLOTS AT 60 DEGREES) INTEGRATED HIGH-PRESSURE PNEUMATIC MECHANICAL CLAMPING AIR BRAKE SYSTEM RIGID REAR FACE MOTOR HOUSING ENCLOSURE PROTECTIVE GUARD CASTING BLOCK DUAL-CONNECTOR COMMUNICATION/POWER CABLING MATRIX FOR MAIN AXIS INTEGRATION S/N: 237981 P1

HAAS HRT210SH SUPER-HIGH SPEED SERVO ROTARY TABLE W/ BISON 8" 6-JAW CHUCK. PLATTER DIAMETER: 8.30" (210 MM). MAX SPEED: 100 / SECOND. MAX TORQUE (CONTINUOUS): 210 FT-LBF (285 NM). GEAR CONFIGURATION: 90:1 GEAR RATIO. BRAKE SYSTEM: NO CONVENTIONAL AIR BRAKE. MAXIMUM PART WEIGHT (UNSUPPORTED): 40 LBS (18.1 KG). MAXIMUM PART DIAMETER: 8.00" (203 MM). CENTER HEIGHT: 6.000" (152.40 MM). INDEXING ACCURACY: 15 ARC-SEC. REPEATABILITY: 10 ARC-SEC. MAXIMUM RUNOUT: 0.0005" (0.013 MM). STANDARD T-SLOTS: 6 SLOTS SPACED AT 60 DEGREES. CENTER BORE DIAMETER: 2.00" (50.8 MM) THRU-BORE. NET ROTARY UNIT WEIGHT: ~165 LBS (75 KG). CHUCK MODEL VARIANT: BISON SERIES 2635 6-JAW SET-TRU SCROLL STYLE CHUCK. NOMINAL DIAMETER: 8-INCH MODEL (200 MM). CHUCK BODY CONSTRUCTION: HIGH-GRADE FORGED STEEL. CHUCK REPEATABILITY (TIR): 0.0004" (0.010 MM). CHUCK THROUGH-HOLE DIAMETER: 2.165" (55 MM). CHUCK MAXIMUM SPEED: 3,100 RPM. CHUCK CLAMPING FORCE: 31,000 N. CHUCK JAW CONFIGURATION: 2-PIECE REVERSIBLE (6 JAWS). INTERFACE CABLING: HEAVY-DUTY BRAIDED CONDUIT DUAL-LINE SERVO COMMUNICATION HARNESS. CONNECTOR CONFIGURATIONS: STANDARD HAAS MULTI-PIN CIRCULAR MILITARY-STYLE SERVO PLUGS. COUNTRY OF MANUFACTURE: MADE IN U.S.A. (OXNARD, CA). EQUIPPED WITH: BISON 8" 6-JAW SET-TRU HIGH-PRECISION MICRO-ADJUSTABLE FORGED STEEL BODY SCROLL CHUCK. S/N: 218581

2004 BROWN & SHARPE GAGE 2000 COORDINATE MEASURING MACHINE, CMM. MEASURING RANGE (X / Y / Z): 18 TO 60 INCH X 20 INCH X 16 INCH (450 MM X 500 MM X 400 MM). GRANITE TABLE SIZE: 21-7/8 INCH X 29-5/8 INCH. MAXIMUM WORKPIECE WEIGHT CAPACITY: 500 LBS (227 KG). MAIN UNIT DIMENSIONS: 33.00 INCH L X 36.00 INCH W X 63.00 INCH H. TOTAL MACHINE WEIGHT: 500 LBS. ELECTRICAL POWER: 100-250 VAC, SINGLE PHASE, 47-63 HZ, 30 VA. PNEUMATIC / AIR SUPPLY: MINIMUM PRESSURE OF 75 PSI (5.2 BAR) AT 1.13 CFM (31.5 L/MIN). ENVIRONMENTAL TEMPERATURE: OPTIMIZED FOR 20C (68F) WITH A MAXIMUM VARIANCE OF 1C. AXIS MOVEMENT: MANUAL POSITIONING WITH PHYSICAL LOCKS AND FINE-ADJUSTMENT KNOBS FOR X, Y, AND Z AXES. BEARINGS: SPECIALIZED AIR BEARINGS ON AXES. S/N: 0204-1583

ASSORTED CAPTO C6 TOOL HOLDERS AND TOOLING

ASSORTED CAPTO C6 TOOL HOLDERS AND TOOLING

1440G 14 INCH X 40 INCH GEARED HEAD GAP BED LATHE WITH FAGOR INNOVA 2-AXIS DRO. MAX. SWING OVER BED: 14 INCH (360 MM). MAX. SWING OVER CROSS CARRIAGE: 9 INCH (233 MM). MAX. SWING IN GAP (INSERT REMOVED): 21 INCH (538 MM). DISTANCE BETWEEN CENTERS: 40 INCH (1,000 MM). WIDTH OF GAP: 9.8 INCH (250 MM). WIDTH OF BEDWAY: 10 INCH (255 MM). SPINDLE BORE DIAMETER: 1-9/16 INCH (40 MM). SPINDLE NOSE MOUNT: CAMLOCK D1-4 OR D1-5. SPINDLE TAPER: MORSE TAPER #5 (MT5). TAILSTOCK QUILL TAPER: MORSE TAPER #3 (MT3). SPINDLE SPEEDS: 16-STEP GEARED (42 TO 2,000 RPM). IMPERIAL / INCH THREADS: 4 TO 112 TPI (40 VARIANTS). METRIC THREADS: 0.25 TO 6.0 MM PITCH (22 VARIANTS). LONGITUDINAL FEED RANGE: 0.002 INCH TO 0.04 INCH / REV. CROSS FEED RANGE: 0.001 INCH TO 0.02 INCH / REV. MAIN SPINDLE MOTOR: 3 HP (220V/230V). COOLANT PUMP MOTOR: 1/8 HP. NET MACHINE WEIGHT: 2,244 LBS (1,020 KG). PHYSICAL FOOTPRINT (L X W X H): 78 INCH X 30 INCH X 60 INCH. EQUIPPED WITH FAGOR INNOVA 20I-T 2-AXIS DIGITAL READOUT SYSTEM (DRO), 6-JAW SCROLL CHUCK, QUICK-CHANGE TOOL POST WITH (10) ASSORTED TOOL HOLDERS, CHUCK SAFETY GUARD WITH LIMIT SWITCH.

ASSORTED CAPTO C6 TOOL HOLDERS AND TOOLING

ASSORTED CAPTO C6 TOOL HOLDERS AND TOOLING

2001 OKUMA LB35 II M HEAVY-DUTY CNC LATHE W/ ROYAL FILTERMIST & CHIP CONVEYOR. MODEL: LB35II-M (LIVE TOOLING CONFIGURATION). CONTROL TYPE: OKUMA OSP-P200L. SWING OVER BED: 27.56 INCH (700 MM). SWING OVER CARRIAGE: 16.93 INCH (430 MM). DISTANCE BETWEEN CENTERS: 59.05 INCH (1,570 MM). MAX. TURNING DIAMETER X LENGTH: 18.11 INCH X 59.03 INCH (460 MM X 1,500 MM). X-AXIS TRAVEL: 12.99 INCH (330 MM). Z-AXIS TRAVEL: 61.81 INCH (1,570 MM). SPINDLE SPEED RANGE: 14 - 3,200 RPM. THROUGH-SPINDLE HOLE DIAMETER: 3.54 INCH (90 MM). SPINDLE BEARING INNER DIAMETER: 5.12 INCH (130 MM). TURRET TYPE: V12 (M-TOOLS). NUMBER OF TOOLS: 12. LIVE TOOLING OD TURNING SHANK SIZE: 1 INCH (25 MM SQUARE). LIVE TOOLING ID TURNING BORE SIZE: 1.97 INCH (50 MM). TURRET INDEX TIME: 0.3 SECONDS / STATION. M-TOOL SPINDLE SPEED: INFINITELY VARIABLE UP TO 2,000 RPM. RAPID TRAVERSE RATES: X-AXIS: 590.55 IPM (15,000 MM/MIN) / Z-AXIS: 787.40 IPM (20,000 MM/MIN). SPINDLE DRIVE MOTOR: VAC 30/20 KW (40/27 HP) (30 MIN/CONT.). CARRIAGE FEED MOTOR (Z-AXIS): 4.8 KW (6.4 HP). CROSS-SLIDE FEED MOTOR (X-AXIS): 3.6 KW (4.8 HP). COOLANT PUMP MOTOR: 0.25 KW (0.333 HP). COOLANT TANK CAPACITY: 250 L (66.1 GAL). MACHINE HEIGHT: 86.22 INCH (2,190 MM). FLOOR SPACE REQUIRED: 191.54 INCH X 105.51 INCH (4,865 MM X 2,680 MM). NET MASS (W/CNC SYSTEM): 25,740 LBS (11,700 KG). ELECTRICAL POWER REQUIREMENTS: AC 200V +/- 10%, 50/60 HZ, 3-PHASE, 48.8 KVA CONTINUOUS. MACHINE OPERATING METRICS: RUNNING TIME: 2094:56:44 HOURS. OPERATING TIME: 738:47:21 HOURS. CUTTING TIME: 705:14:28 HOURS. SPINDLE RUN TIME: 771:14:05 HOURS. EQUIPPED WITH: OKUMA OSP-P200L CNC CONTROL PANEL W/ PULSE GENERATOR HANDWHEEL. LIVE TOOLING (M-AXIS CAPABILITIES). SMX ULTIMATE CHUCK UNIT (NCSE 400-128, MADE IN GERMANY). ROYAL FILTERMIST FX-900 CENTRIFUGAL MIST COLLECTOR / AIR FILTRATION UNIT (MODEL FX-900). ENAMOTO INDUSTRY CO., LTD. HINGED STEEL BELT CHIP CONVEYOR (MODEL LB35-2-850H, SERIAL: 83755). FOOT SWITCH. LATHE CHUCK CONTROLLER PEDAL. INTEGRATED OVERHEAD RIGGING / CRANE HOIST RAIL ASSEMBLY FRAME. 3-COLOR STATUS INDICATOR TOWER LIGHT. S/N: 1308.0702

1993 WEBB 5VK CHAMP 5 HP VERTICAL KNEE MILLING MACHINE WITH MAGNESCALE DRO & CHUCK. TABLE WORKSPACE SIZE: 10" X 54". LONGITUDINAL TRAVEL (X-AXIS): 32". CROSS TRAVEL (Y-AXIS): 16". KNEE TRAVEL (Z-AXIS MANUAL): 19". QUILL TRAVEL: 6". RAM TRAVEL: 24". T-SLOTS CONFIGURATION: 3 SLOTS ON 2.5" CENTERS (5/8" SLOT SIZE). MAXIMUM WORKPIECE WEIGHT CAPACITY: 750 LBS. SPINDLE MOTOR: 5 HP (3-PHASE, 220V/440V). SPINDLE TAPER: NST #40 / NMTB 40. SPINDLE SPEED RANGE: 60 TO 3,800 RPM (MECHANICAL VARIABLE SPEED). QUILL DIAMETER: 4". THROAT DISTANCE: 4-1/4" MINIMUM TO 28-1/4" MAXIMUM. STRUCTURE CASTING: HEAVILY RIBBED CERTIFIED MEEHANITE CASTINGS. WAY SURFACES: INDUCTION HARDENED AND PRECISION GROUND SLIDE WAYS WITH TURCITE-B ANTI-FRICTION COATING. LUBRICATION: INTEGRATED ONE-SHOT MANUAL SLIDING WAY LUBRICATION BLOCK. FLOOR FOOTPRINT REQUIRED: 7' X 10' AREA. MAXIMUM MACHINE HEIGHT: 96". NET TOOL WEIGHT: 3,900 LBS. EQUIPPED WITH: MAGNESCALE LH70-2 DIGITAL READOUT (DRO) SYSTEM, 3-JAW CHUCK ATTACHMENT, ONE-SHOT MANUAL LUBRICATION BLOCK. S/N: 824321

2-TON HANDLING SYSTEMS INTERNATIONAL (HSI) BRIDGE CRANE WITH 2-TON YALE ELECTRIC HOIST 40FT LENGTH

ASSORTED VDI 40 TOOL HOLDERS & TOOLING - MODULAR QUICK-CHANGE & BORING BARS

ASSORTED CAPTO C6 TOOL HOLDERS AND TOOLING

1600 LB FREE-STANDING JIB CRANE W/ YALE ELECTRIC CHAIN HOIST. HANDLING SYSTEMS INTERNATIONAL HSI CRANE. FREE STANDING PILLAR JIB CRANE. 1600 LBS RATED CRANE STRUCTURE CAPACITY. 117 INCHES VERTICAL MAST HEIGHT. 12 FEET HORIZONTAL BOOM LENGTH. YALE HOISTS HOIST. 1/4 TON 250 KG HOIST CAPACITY RATING. ELECTRIC CHAIN DRIVE HOIST OPERATION. BUDGIT TROLLEY. 1600 LBS LABELED TROLLEY LOAD RATING.

ASSORTED CAPTO C6 ASSORTED MODULAR TOOL HOLDERS - QUICK-CHANGE

ASSORTED CAPTO C6 TOOL HOLDERS AND TOOLING

SANDVIK COROMANT CORODRILL 880 INDEXABLE INSERT DRILLS

SANDVIK COROMANT C6-570-3C 32 159 DAMPED CAPTO BORING BAR DIAMETER: 1.260" COUPLING TYPE: 570 COUPLING PRODUCT LINE: COROTURN SL MATERIAL ID: 3729708 BATCH NUMBER: 10996006 COUNTRY OF MANUFACTURE: NORWAY S/N: 2TES182481