MultiFacility CNC Fabrication Process Equipment

MARKFORGED SINTER II FURNACE - SINTER OVEN 2 FOR THE MARKFORGED METAL X 3D PRINTER WITH A HUGE ACTIVE HOT ZONE (18,356 CUBIC CENTIMETERS), THE SINTERING FURNACE-2 FITS THE FULL VOLUME OF THE METAL X. ITS THE PERFECT SOLUTION FOR LARGER PARTS OR MASS PRODUCTION. THIS FURNACE SINTERS THE ENTIRE RANGE OF COMMERCIAL METALS FROM THEIR BROWN (WASHED) CONDITION TO FULLY DENSE METAL PARTS. THE SINTERING FURNACE CAN BE CONTROLLED VIA USB, NETWORK CONNECTION. THE DATA FOR SINTERING IS ALSO DETERMINED BY THE EIGER SOFTWARE. MACHINE SIZE: 1,200 X 700 X 1,500 MM SINTER CAPACITY: CYLINDRICAL 305MM ID X 305 L SINTERING VOLUME: 22,283 CUBIC CM

2007 FREIGHTLINER M2 BUSINESS CLASS FLATBED WITH STAKE SIDES & LIFTGATE. CONVENTIONAL DAY CAB, SINGLE AXLE. FLATBED WITH STAKE SIDES AND HEAVY-DUTY REAR HYDRAULIC RAIL LIFTGATE. INCLUDES STEEL UNDER-BODY TOOL/STORAGE BOX. HAZARDOUS MATERIAL PLACARD HOLDERS. MILEAGE: ~330,000 MILES. TYPICAL RUST, SURFACE WEAR, AND WEATHERING CONSISTENT WITH AGE AND COMMERCIAL USE.

2007 ATRUMP AONE-3VKNC 3 AXIS CNC MILLING MACHINE - VERY LOW HOURS, WAS USED FOR PRIVATE MANUFACTURING OF ALUMINUM PARTS. PURCHASED NEW, NEVER BEEN USED AS A JOB SHOP MACHINE. CENTROID CONTROLLER. COMES WITH 2 INSTALLED KURT VISES. POWERED UP AND RUNNING FOR INSPECTION.

MINSTER P2-100-54 PIECE-MAKER 100 TON FLYWHEEL STRAIGHT SIDE PRESS. MANUFACTURER: THE MINSTER MACHINE COMPANY SERIES: P2-100-60 PIECE-MAKER TYPE: FLYWHEEL STRAIGHT SIDE / PIECE-MAKER TONNAGE RATING: 100 TONS BOLSTER SIZE (L.R. X F.B.): 54" X 31" STROKES PER MINUTE: 0 - 100 SPM STROKE OF SLIDE: 4" MAXIMUM ADJUSTMENT OF SLIDE: 4" SHUTHEIGHT TO BOLSTER: 19" SHUTHEIGHT TO BED: 24" SLIDE ADJUSTMENT RANGE: 11.000" TO 15.000" DIE CUSHION CAPACITY: 9.6 TONS CUSHION STROKE: 2" COUNTERBALANCE CYLINDER EFFECTIVE AREA: 97 SQ. IN. CLUTCH AIR PRESSURE: 60 LBS. MAIN ELECTRIC POWER SUPPLY: 480 V / 3 PH / 60 HZ CLUTCH CONTROL VOLTAGE: 110 V / 1 PH / 60 HZ DRIVE MOTOR FULL LOAD CURRENT: 22 AMPS CONTROL FULL LOAD CURRENT: 4 AMPS CONTROL TRANSFORMER CAPACITY: 750 VA CONTROL VOLTAGE: 120 VOLTS CONTROL DIAGRAM: V-FMH-62-19 A CLUTCH SERIES/TYPE: MAIN SHAFT LOCATION / 126-GC (2 DISCS, 0.073" LEFT/RIGHT SIDE SHRINKAGE) TIE ROD HEATER SIZE: 480 V - 4002 W - 1900 W LUBRICATION SYSTEM: MONITORFLOW CONTINUOUS PRESSURE RE-CIRCULATING SYSTEM EQUIPPED WITH: LITTELL STRAIGHTENER / FEEDER MACHINE ASSEMBLY UNIT (FEED SN: 85583-83) WELDOTRON SAFE-T-LITE SAFETY LIGHT CURTAIN SYSTEM BARS & PANELS DIPRO 1500 WINTRISS DIE PROTECTION CONTROL SYSTEM WINTRISS BRAKE MONITOR CONTROLS (HONEYWELL) STAND-ALONE OPERATOR COMMAND CONSOLE ENCLOSURE WITH RUN/INCH CONTROLS ORIGINAL MINSTER PRESSES SERVICE & OPERATING MANUAL DOCUMENTATION PACK S/N: P2-100-25467

2002 HAAS SL-30 SWING / CAPACITY SWING OVER FRONT APRON: 30" (762MM) SWING OVER CROSS SLIDE: 14.5" (368MM) MAX CUTTING DIAMETER: 17" (368MM) MAX CUTTING LENGTH: 34" (864MM) DISTANCE BETWEEN CENTERS: 39" (991MM) CHUCK SIZE: 10" (STANDARD) / UP TO 15" (OPTIONAL) SPINDLE BORE: 3.5" (76.2MM) DRAW TUBE BORE: 3.03" (65.0MM) MAX BAR CAPACITY: 3" (64MM) AXIS TRAVELS X-AXIS TRAVEL: 11.3" (287MM) Z-AXIS TRAVEL: 34" (864MM) FEEDS & RAPIDS RAPID TRAVERSE (X/Z): 710 IPM AXIS MOTOR MAX THRUST: 15,124 N SPINDLE MAX SPINDLE SPEED: 3,400 RPM SPINDLE MOTOR: 30 HP PEAK (22 KW) TORQUE: 300 FT-LBS (407 NM) @ 700 RPM SPINDLE NOSE: A2-6 DRIVE: AC BRUSHLESS SERVO TURRET TURRET POSITIONS: 12 STATIONS TOOL HOLE IN TURRET: 2" (50.8MM) OD TURNING TOOL SIZE: 1" INDEX TIME (ONE TOOL): 1 SECOND BORING BAR REAR CLEARANCE: 4.25" (108MM) ACCURACY POSITIONING: .0002" (.0051MM) REPEATABILITY: .0001" (.0025MM) UTILITIES POWER REQUIREMENT: 26 KVA VOLTAGE: 200-250 VAC, 3-PHASE, 60 HZ AIR REQUIREMENT: 1.42 LPS @ 100 PSI (6.9 BAR) COOLANT TANK CAPACITY: 50 GAL (189 L) MACHINE DIMENSIONS & WEIGHT DIMENSIONS (L X W X H): 161" X 77" X 74" (APPROX.) MACHINE WEIGHT: 14,000-16,000 LBS (6,350 KG)

HSK 63 HEAT SHRINK TOOL HOLDERS - VARIOUS SIZES AND LENGTHS

2013 MAZAK OPTIPLEX 3015 4.0KW LASER & EMC 3015 AUTOMATION CELL. 2D FLYING OPTICS LASER CUTTING MACHINE WITH AUTOMATED STORAGE & MATERIAL HANDLING TOWER. LASER POWER: 4.0 KW (4,000 WATTS) CO2 RESONATOR. CNC CONTROL: MAZATROL PREVIEW 2 TOUCHSCREEN INTERFACE. X-AXIS TRAVEL: 3,100 MM (122.05"). Y-AXIS TRAVEL: 1,595 MM (62.20"). Z-AXIS TRAVEL: 150 MM (5.91"). MAX. RAPID FEED RATE (X/Y): 2,362 IPM. ACCELERATION: 1.2G. POSITIONING ACCURACY: +/-0.05 MM / 1020 MM. REPEATABILITY: +/-0.03 MM. EQUIPPED WITH ATC (AUTOMATIC TORCH & NOZZLE CHANGER) MULTI-POSITION AUTOMATED CAROUSEL FOR UNATTENDED NOZZLE/TORCH REPLACEMENT BETWEEN MATERIAL CHANGES. INTELLIGENT MONITORING AND INTEGRATED EXHAUST/DUST COLLECTION CONTROL FUNCTIONS. DUAL-PALLET SYSTEM INTEGRATION FOR AUTOMATED CELL TRANSFER. MAXIMUM CUTTING CAPACITIES: MILD STEEL: 25 MM (1.00"), STAINLESS STEEL: 15 MM (0.60"), ALUMINUM: 12 MM (0.50"). MAZAK EXTENSIBLE MANUFACTURING CELL (EMC 3015) AUTOMATED MATERIAL LOAD/UNLOAD STORAGE TOWER SYSTEM. TOTAL SYSTEM WEIGHT: 15,000 KG (APPROX. 33,000 LBS). MATERIAL HANDLING LIMITS: MAX. SHEET WIDTH (W): 1,540 MM (60.6"), MAX. SHEET LENGTH (L): 3,080 MM (121.2"), MAX. SHEET THICKNESS (T): 25 MM (0.98"), MAX. SHEET WEIGHT/MASS (M): 1,000 KG (2,204 LBS) PER SHEET LOAD. ELECTRICAL SPECIFICATIONS: MAIN VOLTAGE: 3-PHASE AC 460V @ 50/60 HZ. MAX CURRENT (MAIN): 7.8 A. CONTROL BOX INPUT: 3-PHASE AC 200V @ 50/60 HZ. CONTROL CIRCUITRY: AC 100V / DC 24V. MAIN MOTOR CURRENT: MAX 36 A @ 200V. RATED CAPACITY: 3 KVA. S/N: 245185 / 245163

2011 TRUMPF TRULASER CELL 3010 FIBER LASER TABLE SIZE: 43.3" X 26" MAX OUTPUT POWER: 2,000 WATTS X-AXIS TRAVELS: 39.4" Y-AXIS TRAVELS: 19.7" Z-AXIS TRAVELS: 15.7" B-AXIS: 120 C-AXIS: CONTINUOUS POSITIONING ACCURACY: 0.0006" ELECTRICAL: 460V, 3-PHASE APPROXIMATE MACHINE WEIGHT: 5,291 LBS APPROXIMATE MACHINE DIMENSIONS: 146" X 110" X 95"

SPOT WELDER # AN4763

OR LASER ECO 100 INDUSTRIAL LASER WELDING MACHINE TRAVEL MOTION: MOTORIZED X, Y, AND Z-AXES X-AXIS TRAVEL: ~90 MM TO 150 MM Y-AXIS TRAVEL: ~210 MM Z-AXIS TRAVEL: ~300 MM MAX WORKPIECE / TABLE LOAD: 120 KG TO 150 KG AXIS CONTROL: INTEGRATED MULTI-FUNCTION JOYSTICK WITH VARIABLE POSITIONING SPEEDS LASER SOURCE: ND:YAG (FLASHLAMP-PUMPED) WAVELENGTH: 1064 NM AVERAGE LASER POWER: 100 WATTS PULSE PEAK POWER: UP TO ~7.5 KW 9 KW MAX PULSE ENERGY: ~60 J TO 100 J PULSE DURATION: 0.2 MS 20 MS PULSE FREQUENCY (REPETITION RATE): 0.5 HZ 20 HZ FOCAL SPOT DIAMETER: 0.2 MM 2.0 MM (CONTINUOUSLY ADJUSTABLE)

OPEX PERFECT PICK IBOT #00476 PAYLOAD CAPACITY: 60 LBS INCLUDING TRAY/TOTE MAX SPEED: UP TO 75 INCHES PER SECOND ACCELERATION: CONFIGURABLE BY TOTE, UP TO 1/2 G POWER: ONBOARD ULTRACAPACITORS (REGENERATIVE CHARGING WHILE TRAVELING, NO REMOVABLE BATTERIES) WIRELESS COMMS: 2.4 GHZ OPERATING ENVIRONMENT: 50F-90F, 0-95% RH, NON-CONDENSING BRAKING: DUAL FAIL-SAFE BRAKING SYSTEMS THROUGHPUT: UP TO 1,000 DUAL CYCLES/HOUR PER IBOT (SYSTEM-DEPENDENT) TRAFFIC CONTROL: CENTRALIZED "SAFE MOVE ONLY" CONTROL SYSTEM MOVEMENT: BI-DIRECTIONAL HORIZONTAL AND VERTICAL WITHIN THE AISLE, FULL ACCESS TO ALL STORAGE LOCATIONS

20XX TOYOTA 30-7FBCU25 CLAMP TRUCK WITH CHARGER. 36-VOLT ELECTRIC (EE RATING). FACTORY-RATED PAPER ROLL CLAMP. FSV (3-STAGE / TRIPLE MAST). MAX LIFT HEIGHT: 189" (15.75 FT / 4,800 MM). RATED CAPACITY: 2,200 LBS @ 25.5" LOAD CENTER (AT MAX LIFT). BACK TILT: 5. SOLID CUSHION TIRES. FRONT TIRES: 21 X 7 X 15. REAR TIRES: 16 X 5 X 12.5. TRUCK WEIGHT (W/O BATTERY): 8,638 LBS. BATTERY WEIGHT RANGE: 2,400 LBS - 3,154 LBS. MAX BATTERY CAPACITY: 1,320 AH (TYPE EO). INCLUDED: BATTERY CHARGER. S/N: 60191

OPEX PERFECT PICK IBOT #00829 PAYLOAD CAPACITY: 60 LBS INCLUDING TRAY/TOTE MAX SPEED: UP TO 75 INCHES PER SECOND ACCELERATION: CONFIGURABLE BY TOTE, UP TO 1/2 G POWER: ONBOARD ULTRACAPACITORS (REGENERATIVE CHARGING WHILE TRAVELING, NO REMOVABLE BATTERIES) WIRELESS COMMS: 2.4 GHZ OPERATING ENVIRONMENT: 50F-90F, 0-95% RH, NON-CONDENSING BRAKING: DUAL FAIL-SAFE BRAKING SYSTEMS THROUGHPUT: UP TO 1,000 DUAL CYCLES/HOUR PER IBOT (SYSTEM-DEPENDENT) TRAFFIC CONTROL: CENTRALIZED "SAFE MOVE ONLY" CONTROL SYSTEM MOVEMENT: BI-DIRECTIONAL HORIZONTAL AND VERTICAL WITHIN THE AISLE, FULL ACCESS TO ALL STORAGE LOCATIONS

OPEX PERFECT PICK IBOT #00830 PAYLOAD CAPACITY: 60 LBS INCLUDING TRAY/TOTE MAX SPEED: UP TO 75 INCHES PER SECOND ACCELERATION: CONFIGURABLE BY TOTE, UP TO 1/2 G POWER: ONBOARD ULTRACAPACITORS (REGENERATIVE CHARGING WHILE TRAVELING, NO REMOVABLE BATTERIES) WIRELESS COMMS: 2.4 GHZ OPERATING ENVIRONMENT: 50F-90F, 0-95% RH, NON-CONDENSING BRAKING: DUAL FAIL-SAFE BRAKING SYSTEMS THROUGHPUT: UP TO 1,000 DUAL CYCLES/HOUR PER IBOT (SYSTEM-DEPENDENT) TRAFFIC CONTROL: CENTRALIZED "SAFE MOVE ONLY" CONTROL SYSTEM MOVEMENT: BI-DIRECTIONAL HORIZONTAL AND VERTICAL WITHIN THE AISLE, FULL ACCESS TO ALL STORAGE LOCATIONS

SULLAIR LS-100 AIR COMPRESSOR

GRIEVE 84-500 150" X 82" X 79" NATURAL GAS INDUSTRIAL BATCH OVEN. MAXIMUM TEMPERATURE CAPACITY: 500F. GAS HEAT INPUT RATING: 500,000 BTU/HR. OVEN INSIDE DIMENSIONS: 150" L X 82" W X 79" H. INTERNAL VOLUME: 562 CUBIC FEET. GROSS PROCESSING MATERIAL CAPACITY: 1,500 LBS. BAKING CYCLE TIME (BATCH OVEN): 8 TO 10 HOURS. FRESH AIR INTAKE VOLUME: 417 CFM AT 70F. PURGING INTERVAL CONTROL: 10 MINUTES. MAIN ELECTRICAL POWER: 208V / 3 PHASE / 60 HZ / 10 AMPS. CIRCULATION FAN MOTOR: 5 HP. CONTROL POWER VOLTAGE: 120V / 1 PHASE / 60 HZ. BURNER MODEL: INCINOMITE MODEL 121-3. EQUIPPED WITH: HONEYWELL TRULINE CIRCULAR CHART RECORDER (MODEL DR4500 / DR45AT), HONEYWELL DIGITAL CONTROL SYSTEM WITH DIAGNOSTIC DISPLAY LIGHTS, HONEYWELL FLUID POWER GAS SAFETY VALVE SYSTEM, HONEYWELL BURNER CONTROL BOX CONTROLLER, HONEYWELL MODUTROL IV MOTOR VALVE ACTUATOR (MODEL M7284C1000), RED LION CONTROLS DIGITAL TIMER UNIT. COMPLETE ORIGINAL PAPER FACTORY OPERATING AND INSTALLATION MANUAL BINDER DOCUMENTATION STACK. DOUBLE-DOOR WALK-IN FRONT ACCESS ENTRY SYSTEM WITH COMPRESSION DOOR LATCHES. S/N: 411110

NISSAN CSP01L15S ELECTRIC FORKLIFT WITH CHARGER - 12,969 HOURS - MAKE: NISSAN FORKLIFT CORPORATION MODEL VARIATION: CSP01L15S CHASSIS NO.: CSP01-9A2372 HOURS: 12,969 HOURS TYPE SAFETY RATING: ES ATTACHMENT: FORKS S/S (SIDE SHIFT) 55FSSA074 MAST: N3F515 TIRE TREAD: STANDARD TREAD MAX LIFT HEIGHT: 203 INCH (APPROX. 16.9 FT) CAPACITY RATINGS (VERTICAL MAST): 2,150 LBS @ 24 IN LOAD CENTER 1,900 LBS @ 28 IN LOAD CENTER 1,695 LBS @ 32 IN LOAD CENTER WEIGHTS & BATTERY SPECIFICATIONS: TRUCK WEIGHT (WITHOUT BATTERY): 5,420 LBS MIN BATTERY WEIGHT: 1,840 LBS MAX BATTERY WEIGHT: 2,535 LBS BATTERY TYPE: EO INCLUDED: BATTERY CHARGER S/N: CSP01-9A2372

(4,000 LBS. ALLOWABLE STATIC LOAD CAPACITY) AWP INDUSTRIES INDUSTRIAL WIRE BASKETS WITH FRONT DROP-GATE DESIGN AND LOCKING CORNER STACK FEET. EXTERIOR DIMENSIONS: 39" L X 32" W X 39" D. MAX STACKING HEIGHT: 4 HIGH. OKAY STAINLESS STEEL MESH STRAINER CAGES. DIMENSIONS: 14" L X 18" W X 10" D. FINE STAINLESS WIRE MESH BODY CONSTRUCTION WITH SOLID REINFORCING PERIMETER BANDS AND DUAL SWING CARRYING HANDLES. PLASTIC STACKING TOTES. TOP DIMENSIONS: 26" L X 18" W. HEAVY-DUTY NESTING AND STACKING INDUSTRIAL PLASTIC DESIGN.

1995 FADAL 4020HT VERTICAL MACHINING CENTER MODEL 906-1 TRAVELS X-AXIS: 40" | Y-AXIS: 20" | Z-AXIS: 20" TABLE TABLE SIZE: 47.94" 20" | MAX WEIGHT ON TABLE: 1,500 LBS FLOOR TO TABLE: 32" | SPINDLE NOSE TO TABLE: 4"24" FEED RATES RAPID TRAVERSE (X, Y, Z): 900 IPM SPINDLE SPINDLE SPEED: 7510,000 RPM | SPINDLE TAPER: CAT-40 | SPINDLE MOTOR: 15 HP TOOL CHANGER 21-POSITION ATC CONTROL FADAL CNC 88HS MACHINE DIMENSIONS & WEIGHT DIMENSIONS: 116" L 87" W 95" H | MACHINE WEIGHT: ~10,100 LBS POWER 230V / 440V, 3-PHASE S/N: 9502935

CHEVALIER SURFACE GRINDER MAGNETIC CHUCK / TABLE SIZE: 12" X 24" (300 MM X 600 MM) MAX. LONGITUDINAL TRAVEL: 25.6" (650 MM) MAX. CROSS TRAVEL: 12" (300 MM) MAX. DISTANCE CENTERLINE SPINDLE TO TABLE: 20" 24" (500 MM 610 MM) MAX. TABLE LOAD (INCLUDING CHUCK): ~920 LBS (420 KG) SPINDLE & GRINDING WHEEL SPINDLE MOTOR: 5 HP (3.7 KW) SPINDLE SPEED: 1,750 RPM @ 60 HZ (3,450 RPM OPTIONAL DEPENDING ON WHEEL SIZE) STANDARD WHEEL SIZE: 12" OD X 1.25" WIDTH X 3" BORE (305 X 32 X 76.2 MM)

WISCONSIN OVEN SDB-8128-12G 1250F NATURAL GAS INDUSTRIAL BATCH OVEN. MAXIMUM TEMPERATURE CAPACITY: 1250F. TYPE OF FUEL: NATURAL GAS. GAS SUPPLY PRESSURE: 2 - 5 PSIG. GAS INPUT RATING: 800,000 BTU/HR (800 SCFH @ 1,000 BTU/SCF). RECIRCULATION AIR FLOW: 10,000 CFM VIA 15 HP CIRCULATION BLOWER. EXHAUST SYSTEM: 6" BLASTGATE VENT. GROSS LOADING CAPACITY: 600 LBS. INTERNAL BASKET/CHAMBER DIMENSIONS: 48" BASKET LENGTH X 48" BASKET WIDTH X 72" BASKET HEIGHT (54" CHAMBER PROFILE). DOOR STYLE: VERTICAL LIFT DOOR WITH AIR-OPERATED SAFETY LATCH AND COUNTERWEIGHTS. ELECTRICAL REQUIREMENTS: 480V / 3 PHASE / 60 HZ. FULL LOAD CURRENT: 23 AMPS (LARGEST MOTOR: 21 AMPS). SHORT CIRCUIT CURRENT RATING: 5 KA RMS SYMMETRICAL AT 480V. MAX OVEN BODY EXTERIOR DIMENSIONS: 105-7/8" SHIPPING WIDTH X 94" SHIPPING LENGTH (10'-11-9/16" OVERALL LENGTH WITH DOOR SWING) X 10'-8-15/16" SHIPPING HEIGHT (15'-7" CEILING CLEARANCE HEIGHT). EQUIPPED WITH: GE CONTROL C-2000 MAIN CONTROL PANEL UNIT, ECLIPSE 236 JIB BURNER ASSEMBLY, HONEYWELL FLUID POWER GAS SAFETY VALVES (MODELS V4055D & V4055A), HONEYWELL INTEGRATED BURNER SAFETY CONTROLS, PNEUMATIC AND GAS FUEL TRAIN PIPING ASSEMBLIES, DOOR HAND-VALVE CONTROL STATION ASSEMBLY, COMPLETE GENERAL ASSEMBLY BLUEPRINTS, SCHEMATICS, AND OPERATIONAL DOCUMENT MANUALS. S/N: 06125A1310

1994 FADAL 4020HT VERTICAL MACHINING CENTER MODEL 906 TRAVELS X-AXIS: 40" | Y-AXIS: 20" | Z-AXIS: 20" TABLE TABLE SIZE: 47.94" 20" | MAX WEIGHT ON TABLE: 1,500 LBS SPINDLE NOSE TO TABLE: 4"24" | FLOOR TO TABLE: 32" FEED RATES RAPID TRAVERSE (X, Y, Z): 900 IPM SPINDLE SPINDLE SPEED: 10,000 RPM | SPINDLE TAPER: CAT-40 | SPINDLE MOTOR: 15 HP HIGH TORQUE TOOL CHANGER 21-POSITION ATC CONTROL FADAL CNC 88 POWER 230V / 440V, 3-PHASE MACHINE WEIGHT ~10,10011,000 LBS DEPENDING ON CONFIGURATION S/N: 31994060403

(4) NIIGATA SPN50-H.O. CNC HORIZONTAL MACHINING CENTER CELL WITH 30-STATION PALLET POOL FMS. NUMBER OF MACHINES: 4 HORIZONTAL MACHINING CENTERS. PALLET POOL CAPACITY: 30 STATIONS. PALLET SIZE: 19.7 X 19.7 INCHES (500 X 500 MM). X-AXIS TRAVEL: 28.7 INCHES (730 MM). Y-AXIS TRAVEL: 28.7 INCHES (730 MM). Z-AXIS TRAVEL: 27.6 INCHES (700 MM). TABLE LOAD CAPACITY: 1,100-1,540 LBS (500-700 KG) PER PALLET. SPINDLE SPEED: 12,000 RPM (OPTIONAL 15,000 / 20,000 RPM). SPINDLE TAPER: CAT 40 / HSK-A63 (OPTIONAL CAT 50 / BT 50). SPINDLE MOTOR: 30 HP / 40 HP. TOOL CHANGER CAPACITY: 60 / 120 / 180 STATIONS PER MACHINE (DEPENDENT ON ATC OPTION). RAPID TRAVERSE (X/Y/Z): 1,968 IPM (50 M/MIN). B-AXIS INDEXING: 0.001 DEGREE (FULL 4TH AXIS CONTOUR).

HAAS VF-4 VERTICAL MACHINING CENTER, VMC X-AXIS TRAVEL: 50 INCHES Y-AXIS TRAVEL: 20 INCHES Z-AXIS TRAVEL: 25 INCHES TABLE SIZE: 52 X 18 INCHES MAXIMUM TABLE LOAD: 3,500 LBS SPINDLE SPEED: 8,100 RPM SPINDLE TAPER: CAT 40 SPINDLE MOTOR: 20 HP / 30 HP VECTOR DRIVE TOOL CHANGER CAPACITY: 20 STATIONS CAROUSEL STYLE MAX TOOL WEIGHT / LENGTH: 12 LBS / 13 INCHES RAPID TRAVERSE (X/Y/Z): 710 IPM MACHINE WEIGHT: APPROX. 13,300-14,500 LBS S/N 10372

CRESS HEAT TREAT OVEN MAXIMUM INTERMITTENT TEMPERATURE: 2250F MAXIMUM CONTINUOUS TEMPERATURE: 2000F TEMPERATURE RANGE: 300F-2250F TEMPERATURE UNIFORMITY: APPROXIMATELY 25F

1 ZEFIRO EV AP 560 PN 5HP, THREE-PHASE, 460V 60HZ, ZONE 22, 6.4HP, 26GALLON CAPACITY, 200MM (8-INCH.) INLET, POLYESTER ANTISTATIC CLASS M CARTRIDGE FILTER, AUTOMATIC PNEUMATIC FILTER CLEANING SYSTEM H H14 HEPA FILTER ARTICULATING SUCTION ARM FOR EV AP D150 - INLET D200 INDUSTRIAL VACUUM

2 VERTICAL STORAGE TANK 4900G, 1.9 SG, 90D X 202H S/N: SII5840000N45

CHICAGO PNEUMATIC C.P.450E COMPRESSION RIVETER WITH LINEMASTER FOOT SWITCH. MANUFACTURER: CHICAGO PNEUMATIC TOOL COMPANY. MODEL NUMBER: C.P.450E. SERIAL NUMBER: H132048 (TAG ALSO SHOWS T9277). EQUIPMENT TYPE: PNEUMATIC COMPRESSION RIVETER / SQUEEZER. FOOT SWITCH MANUFACTURER: LINEMASTER SWITCH CORPORATION. FOOT SWITCH CAT. NO.: 522-B14 (FULL GUARD MODEL). S/N: H132048

CLAUSING COLCHESTER 15X48 ENGINE LATHE - MANUAL ENGINE LATHE SWING OVER BED: 15" DISTANCE BETWEEN CENTERS: 48" HEAVY-DUTY CAST-IRON CONSTRUCTION GEARED HEADSTOCK MANUAL CARRIAGE AND CROSS-SLIDE CONTROLS POWER LONGITUDINAL AND CROSS FEEDS THREADING CAPABILITY LEADSCREW AND FEED ROD ADJUSTABLE TAILSTOCK TAILSTOCK DRILL CHUCK QUICK-CHANGE TOOL POST 3-JAW CHUCK

LINCOLN PRECISION TIG 375 S/N 1030921921

1990 HAAS VF-1 CNC MACHINE CENTER TABLE SIZE: 26" X 14" (660MM X 356MM) MAX. TABLE LOAD: ~750 LBS T-SLOTS: 3 SLOTS, 5/8" WIDE X-AXIS TRAVEL: 20" (508MM) Y-AXIS TRAVEL: 16" (406MM) Z-AXIS TRAVEL: 20" (508MM) SPINDLE NOSE TO TABLE: 4"-24" RAPID TRAVERSE (X/Y/Z): 480 IPM MAX CUTTING FEED RATE: ~200 IPM SPINDLE SPEED: 0-5,000 RPM SPINDLE TAPER: CAT 40 SPINDLE MOTOR: 7.5 HP PEAK DRIVE: BELT DRIVE AXIS DRIVE: BRUSH-TYPE DC SERVOMOTORS (ALL AXES) ATC CAPACITY: 16 TOOLS ATC TYPE: CAROUSEL (UMBRELLA STYLE) HAAS CNC CONTROL (1ST GENERATION) PROGRAM MEMORY: 128K PROCESSING SPEED: ~20 BLOCKS/SECOND INTERFACE: RS-232 POWER: 195-260 VAC, 3-PHASE COOLANT: FLOOD COOLANT SYSTEM MACHINE WEIGHT: APPROX. 7,000 LBS

ROBOVENT PLASER SERIES PL-5000-4 INDUSTRIAL DUST COLLECTOR. 7.5 HP MOTOR, 230 VAC, 3 PHASE, 22 A FULL LOAD AMPS, 5 KA SCCR. FOUR (4) CARTRIDGE FILTER DESIGN, APPROX. 2,048 SQ. FT. TOTAL FILTER MEDIA. AUTOMATIC PULSE-JET FILTER CLEANING SYSTEM, DIFFERENTIAL PRESSURE MONITORING. APPROXIMATE AIRFLOW: 2,500-3,000 CFM. ROBOVENT EPAD TOUCH-CONTROL INTERFACE, AUTOMATIC FILTER PULSE CLEANING, DIFFERENTIAL PRESSURE DISPLAY, INTEGRATED ELECTRICAL CONTROL PANEL, EMERGENCY STOP BUTTON. HEAVY-DUTY WELDED STEEL CABINET, HOPPER-STYLE DUST COLLECTION SECTION, INTEGRATED BLOWER ASSEMBLY, VERTICAL CARTRIDGE FILTER CONFIGURATION. DIMENSIONS: 83 IN. LENGTH, 30 IN. WIDTH, 97 IN. HEIGHT CABINET (APPROXIMATELY 11-12 FT OVERALL WITH BLOWER). ESTIMATED WEIGHT: 1,300-1,700 LBS. APPLICATIONS: LASER CUTTING, PLASMA CUTTING, THERMAL CUTTING, METAL FABRICATION. AUTOMATIC PULSE-CLEANING FILTRATION SYSTEM, TOUCHSCREEN CONTROLLER INSTALLED. S/N: 23054

CAT 50 HEAT SHRINK TOOL HOLDERS - VARIOUS SIZES AND LENGTHS

2000 BRIDGEPORT SERIES I MANUAL VERTICAL KNEE MILLING MACHINE WITH 2J VARIABLE SPEED HEAD. TABLE SIZE 9" X 48" OR 9" X 49". TABLE TRAVEL (X-AXIS) 33" (WITH POWER FEED) TO 36" (MANUAL). SADDLE TRAVEL (Y-AXIS) 12". KNEE TRAVEL (Z-AXIS) 16". QUILL TRAVEL 5". RAM TRAVEL 12". SPINDLE TAPER R-8. SPINDLE MOTOR POWER 2 HP (CONTINUOUS DUTY) / 3 HP (30-MIN DUTY). SPINDLE SPEED RANGE LOW: 60-500 RPM / HIGH: 500-4,200 RPM (INFINITELY VARIABLE).

SPEEDFAM SNG-24BTAW-1188 PRECISION FLAT LAPPING/POLISHING MACHINE LAPPING PLATE DIAMETER: 24 INCHES RETAINING / PRESSURE PLATES: 4 SETS OF PNEUMATIC PRESSURE PLATES DOWN PRESSURE SYSTEM: AIR CYLINDER PNEUMATIC PRESSURE CONTROL MACHINE DIMENSIONS: 1,200 MM WIDTH X 1,240 MM DEPTH X 1,800 MM HEIGHT MACHINE WEIGHT: 1,000 KG (2,200 LBS) S/N: 1188

OKUMA CADET MATE 40X20X20 CNC MILL SPECIFICATIONS: MACHINE MODEL OKUMA CADET MATE 4020 MACHINE TYPE VERTICAL MACHINING CENTER (VMC) CNC CONTROL SYSTEM OKUMA OSP-700M (OR OSP-5020M) TRAVELS (X / Y / Z) X: 40 INCH (1016 MM) / Y: 20 INCH (508 MM) / Z: 20 INCH (508 MM) TABLE DIMENSIONS 47.2 INCH X 20 INCH (1200 MM X 508 MM) MAX TABLE LOAD 1,100-1,500 LBS (~500-680 KG) SPINDLE SPEED RANGE 40 TO 8,000 RPM SPINDLE TAPER CAT 40 SPINDLE MOTOR POWER 15 HP (11.2 KW) AUTOMATIC TOOL CHANGER 20-STATION CAROUSEL / UMBRELLA STYLE RAPID TRAVERSE RATES X/Y: 941 IPM, Z: 475 IPM MACHINE WEIGHT APPROX. 11,000-12,000 LBS (5,000-5,500 KG)

TRINCO 48X48 BEAD BLASTER - SPLIT LEVEL DIRECT PRESSURE CABINET BLASTING AREA OF THIS UNIT IS 48" WIDE AND 48" DEEP SO IT WILL HANDLE ANYTHING FROM SUPER SMALL TO VERY LARGE PIECES. 240 VOLT SINGLE PHASE A TRINCO DIRECT PRESSURE CABINET UTILIZES AN A.S.M.E. CODED PRESSURE POT TO HOLD ABRASIVE MEDIA. WHEN THE FOOT PEDAL CONTROL IS DEPRESSED, AIR PRESSURE IS RELEASED INTO THE PRESSURE POT, PRESSURIZING THE POT AND THEN FORCING THE MEDIA FROM THE POT THROUGH THE BLASTING HOSE TO THE NOZZLE. MOST TRINCO PRESSURE BLAST CLEANING IS DONE AT 40-60 PSI. DUE TO THESE LOWER PRESSURES, ABRASIVE MEDIA BREAKDOWN IS GREATLY REDUCED EVEN THOUGH A HIGH VOLUME OF MEDIA IS BEING DIRECTED AT THE PART TO BE CLEANED. MOST OF THE MEDIA IS RECOVERED THROUGH THE RECYCLING PROCESS. TRINCO DIRECT PRESSURE BLAST CLEANING IS IDEAL FOR THE VERY TOUGH JOBS, FOR APPLICATIONS WHERE LARGE SURFACES MUST BE CLEANED QUICKLY, FOR PRODUCTION BLAST CLEANING OR WHEN THE JOB REQUIRES THE USE OF HEAVY MESH SIZES OF SILICON CARBIDE, ALUMINUM OXIDE, GARNET, ETC. OTHER POPULAR MEDIAS THAT ARE USED IN TRINCO PRESSURE CABINETS ARE GLASS BEADS, TRIN-MIXES, RAD-MIX, AND PLASTIC BLAST CLEANING MEDIA. THIS IS NOT A GENERAL SUCTION SAND BLASTING CABINET. THIS IS A PRESSURIZED, FILTERED AND VACUUM SEPARATED SELF CONTAINED UNIT. IT IS COMMERCIAL GRADE AND WOULD BE AN EXCELLENT ALL-IN-ONE CABINET BLASTING SYSTEM THAT OPERATES ON MULTIPLE MEDIA.

HOT WATER BOILER CAPACITY: 5,000,000 BTU/HR (5 MMBTU), FUEL TYPE: NATURAL GAS. POWER SUPPLY: 460V, 3-PHASE PRIMARY POWER WITH A 120V SINGLE-PHASE CONTROL PANEL. MAX TEMPERATURE: RATED FOR CYCLING CONTROL UP TO 551F

2022 ZHONGCAN TECHNOLOGY ZC-DB-9060 100W LASER ENGRAVING MACHINE W/DUAL HEADS, AIR PURIFIER, AND CHILLER. PROFESSIONAL-GRADE LASER ENGRAVING MACHINE EQUIPPED WITH AN INDUSTRY-STANDARD RUIDA CONTROLLER AND A LARGE WORK AREA, IDEAL FOR PRECISION CUTTING AND DETAILED ENGRAVING ACROSS A WIDE VARIETY OF MATERIALS. SPECIFICATIONS MANUFACTURER: ZHONGCAN TECHNOLOGY CO., LTD. MODEL: ZC-DB-9060 SERIAL NUMBER: ZC202206 PRODUCTION DATE: JUNE 17, 2022 CONTROLLER: RUIDA LASER POWER: 90W WORKING AREA: 900 X 600 MM VOLTAGE: 110V WEIGHT: 500 KG (~1,102 LBS) KEY FEATURES RUIDA CONTROL SYSTEM: OFFERS SEAMLESS COMPATIBILITY WITH POPULAR DESIGN AND LASER SOFTWARE SUCH AS LIGHTBURN AND RDWORKS. GENEROUS WORKSPACE: THE 900 X 600 MM BED PROVIDES AMPLE SPACE FOR MEDIUM-TO-LARGE PROJECTS OR BATCH PROCESSING MULTIPLE SMALLER ITEMS. STANDARD 110V POWER: PLUGS DIRECTLY INTO STANDARD NORTH AMERICAN OUTLETS WITHOUT REQUIRING SPECIAL WIRING UPGRADES. INDUSTRIAL CONSTRUCTION: HEAVY-DUTY FRAME (500 KG) ENSURES MINIMAL VIBRATION AND STABILITY DURING HIGH-SPEED OPERATIONS. CUSTOMIZED UNIT FEATURING DUAL HEADS AND SERVO MOTORS RATHER THAN STANDARD STEPPING MOTORS. IT ALSO INCLUDES AN AIR PURIFIER SYSTEM. S/N: ZC202206

EVAPCO ATC-423B COOLING TOWER. BELT NO.: 4B-158. COIL TEST PRESSURE: 400 PSIG. CONSTRUCTION: G-235 HOT-DIP GALVANIZED STEEL (EVAPCOAT FINISH). S/N: 8-340967

2001 FREIGHTLINER FL70 TRUCK CAT 3126 DIESEL ENGINE 7.2L AIR RIDE DRIVER SEAT 353,000 MILES EATON FULLER MANUAL TRANSMISSION STAKE BED AERO CONESTOGA COVER WORKING - NEEDS MAINTENANCE NEW PARTS: FUEL TANKS 2023 BATTERIES 8-27-25 BRAKE AIR HOSE 8-27-25 BRAKE AIR VALVE 8-27-25 SPARE PARTS: BLOCK HEATER BRAKE CHAMBER AIR FILTERS 2PCS FUEL FILTERS 4PCS OIL FILTER S/N: 1FVABTAK61HJ21459

ROUSSELLE B1-55F 55 TON PRESS. MODEL NO: B1-55F TONNAGE: 55 TONS STROKES PER MINUTE (SPM): 120 STROKE LENGTH: 3" SHUT HEIGHT: 13" SLIDE ADJUSTMENT: 4" VOLTAGE: 480V EQUIPPED WITH: LINK SYSTEMS SS-501 PRESS CONTROL SAFETY BOX SYSTEM PANEL AIR COUNTERBALANCE SYSTEM (MAXIMUM UPPER DIE WEIGHT: 700 LBS.) CLUTCH/BRAKE AIR PRESSURE & COUNTERBALANCE AIR PRESSURE CONTROLS WITH GAUGES ONE-SHOT OR AUTOMATIC WAY LUBRICATION SYSTEM STATION EMERGENCY STOP AND TOP STOP CONTROL BUTTONS S/N: P-33490

ROUSSELLE B1-55-F 55 TON PRESS. SPECIFICATIONS: MODEL NO: B1-55-F TONNAGE: 55 TONS STROKES PER MINUTE (SPM): 120 STROKE LENGTH: 3" SHUT HEIGHT: 13" SLIDE ADJUSTMENT: 4" MAIN MOTOR: 5 HORSEPOWER CURRENT: 30 AMPERES VOLTAGE: 460 - 480 VAC PHASE / FREQUENCY: 3 PH / 60 HZ SHORT CIRCUIT CURRENT RATING: 5 KA EQUIPPED WITH: CIECO PLS-PLUS MODEL K-2000 ELECTRONIC CONTROL SYSTEM PANEL AIR COUNTERBALANCE SYSTEM (MAXIMUM UPPER DIE WEIGHT: 700 LBS.) CLUTCH/BRAKE AIR PRESSURE & COUNTERBALANCE AIR PRESSURE CONTROLS WITH GAUGES ONE-SHOT OR AUTOMATIC WAY LUBRICATION SYSTEM. S/N: P-33495

2 VERTICAL STORAGE TANK 4900G VERTICAL STORAGE TANK, 1.5 SG, 90D X 202H S/N: 5840000N43

1999 ATRUMP B8AC CNC MILLING MACHINE TRAVEL / WORK ENVELOPE X-AXIS (LONGITUDINAL): 50 INCH Y-AXIS (CROSS): 22 INCH Z-AXIS (VERTICAL): 2425 INCH WORK TABLE: 57 INCH 18 INCH SPINDLE SPINDLE MOTOR: 10 HP SPEED RANGE: 60-6,000 RPM TAPER: NT40 (CAT40 ON SOME CONFIGURATIONS) FEED FEED MOTORS (X/Y/Z): 2 KW AC RAPID TRAVERSE: 10,000 MM/MIN (393 IPM) CUTTING FEED RATE: 5,000 MM/MIN (196 IPM) ATC 20-STATION ATC (ON STANDARD CONFIGURATIONS) ELECTRICAL / UTILITIES POWER: 220V / 60 HZ / 3-PHASE POWER REQUIREMENT: ~1517 KVA AIR REQUIRED: 85-100 PSI COOLANT PUMP: 1/8 HP COOLANT CAPACITY: ~16-26 GALLONS

VECTRAX VERTICAL MILLING MACHINE SPINDLE & DRIVE SYSTEM: MOTOR & DRIVE: 5 HP INVERTER-DUTY SPINDLE MOTOR CAPABLE OF VARIABLE SPEED CONTROL VIA THE CENTROID CNC INTERFACE. POWER DRAWBAR: TOP-MOUNTED AUTOMATIC/PNEUMATIC POWER DRAWBAR SYSTEM FOR QUICK TOOL CHANGES. CONTROL UNIT: CENTROID M-400 INV CNC CONTROL

2005 FADAL VMC4525 VHT VERTICAL MACHINING CENTER TRAVELS X-AXIS: 45 INCH | Y-AXIS: 25 INCH | Z-AXIS: 24 INCH TABLE TABLE SIZE: 53.5 INCH 25 INCH FEED RATES CUTTING FEED RATE: 0.01400 IPM | RAPID TRAVERSE X/Y: 900 IPM | RAPID TRAVERSE Z: 700 IPM SPINDLE SPINDLE TAPER: CAT-40 | SPINDLE SPEED: 1010,000 RPM SPINDLE MOTOR: 30 HP (AUTOMATIC 2-SPEED VECTOR MOTOR, HIGH TORQUE) TOOL CHANGER 24-POSITION AUTOMATIC TOOL CHANGER, SIDE MOUNTED TOOL DIMENSIONS MAX TOOL DIAMETER: 101.6 MM (4 INCH) | MAX TOOL LENGTH: 381 MM (15 INCH) CONTROL SIEMENS SINUMERIK CNC CONTROL MACHINE DIMENSIONS & WEIGHT WIDTH: 2,300 MM | DEPTH: 3,250 MM | HEIGHT: 3,040 MM | MACHINE WEIGHT: ~6,169 KG (13,600 LBS) S/N: 12004117093

2020 M.T.A. TAEEVO TECH 081 WATER CHILLER VOLTAGE: 460/265 V PHASE/FREQUENCY: 3 PH / 60 HZ INSTALLED POWER: 15 KW (15.00 HP) MAX ABSORPTION CURRENT: 21 A LARGEST MOTOR FLA: 17.1 A SHORT CIRCUIT CURRENT RATING: 10 KA PROTECTION RATING DEGREE: IP54 / TYPE1 REFRIGERANT: R410A REFRIGERANT CHARGE: 5.00 KG (11.02 LBS) MAX WORKING PRESSURE (REFRIGERANT): 42.0 BAR (609.2 PSI) MAX TEMPERATURE (REFRIGERANT): 65.8C (150.4F) UTILIZATION FLUID: WATER MAX WORKING PRESSURE (WATER): 6.0 BAR (87.0 PSI) MAX TEMPERATURE (WATER): 35.0C (95.0F) AMBIENT TEMPERATURE RANGE: -5C TO +43C (23F TO +109.4F) SOUND PRESSURE LEVEL: 70.9 DB(A) WEIGHT: 356 KG (784.84 LBS) S/N: 2200352276

2007 GENIE GS-1930 ELECTRIC SCISSOR LIFT PLATFORM HEIGHT: 19 FT. WORKING HEIGHT: 25 FT. PLATFORM CAPACITY: 500 LBS. PLATFORM EXTENSION DECK: YES POWER SOURCE: 24V BATTERY ELECTRIC DRIVE SYSTEM: ELECTRIC DRIVE MACHINE WIDTH: 30 IN. MACHINE LENGTH: APPROXIMATELY 72 IN. MACHINE WEIGHT: APPROXIMATELY 2,700 LBS. TIRES: NON-MARKING SOLID RUBBER FEATURES QUIET, ZERO-EMISSION ELECTRIC OPERATION SLIDE-OUT PLATFORM EXTENSION PROPORTIONAL LIFT AND DRIVE CONTROLS ON-BOARD BATTERY CHARGER NON-MARKING TIRES COMPACT DESIGN FOR NARROW AISLES AND STANDARD DOORWAYS TIGHT TURNING RADIUS FOR EXCELLENT MANEUVERABILITY FOLD-DOWN GUARDRAILS FOR EASIER TRANSPORT AND STORAGE LOW-MAINTENANCE ELECTRIC DRIVE SYSTEM HAVE BATTERY ISSUES S/N: 200164278

ALFA LAVAL MAPX-207 SELF-CLEANING DISC-STACK CENTRIFUGE / OIL PURIFIER. TYPE: SELF-CLEANING DISC-STACK CENTRIFUGAL SEPARATOR. WORM WHEEL SHAFT SPEED: 1700-1800 R/M. REVOLUTION COUNTER (BOWL SPINDLE): 142-150 R/M. MOTOR: 5.5 KW (7.5 HP), 440V / 3-PHASE / 60HZ. MAX CAPACITY: 5,750-7,400 L/HR (PRODUCT/VISCOSITY DEPENDENT). BOWL/PRODUCT CONTACT PARTS: STAINLESS STEEL. CONFIGURATION: SKID-MOUNTED WITH INTEGRATED FEED PUMP, PIPING, PRESSURE GAUGES, AND CONTROL PANEL. CONTROL PANEL FEATURES: BOWL SLIDE START/ON, SLUDGE SHOOT, LIQUID SEAL ALARM/RESET, PROBE START/STOP. APPLICATIONS: PURIFICATION/CLARIFICATION OF FUEL OIL, LUBRICATING OIL, HYDRAULIC OIL, BIODIESEL, DISTILLATE. TYPICAL USE: MARINE VESSELS, POWER PLANTS, REFINERIES, INDUSTRIAL OIL PROCESSING. CONDITION NOTES: OUTDOOR PLANT ENVIRONMENT, SURFACE RUST ON PANEL/HOUSING, BOWL INTERNALS NOT INSPECTED IN PHOTOS PROVIDED. S/N: 297/275