Plastic Sheet Lines Ancillary Equipment

1989 DAVIS STANDARD 45IN45 SINGLE SCREW EXTRUDER S/N: K9443, SO# 02310, 13.7 GEARBOX RATIO, 250 HP DC MOTOR, 4.5" DIAMETER SCREW, 34:1 L/D RATIO, ELECTRICALLY HEATED, WATER COOLED, VENTED AND PLUGGED BARREL, 7 BARREL ZONES, HES 301 CONTROLS; ONE (1) USED 7.5 HP CONAIR VACUUM LOADER; ONE (1) USED WALTON STOUT FOUR MATERIAL VOLUMETRIC BLENDER; ONE (1) USED XALOY EH-45 SCREEN CHANGER SERIAL # EH45788 WITH 2 HP BERINGER HYDRAULIC PUMP; ONE (1) USED DAVIS STANDARD / MARSHAL & WILLIAMS THREE ROLL SHEET STACK 36" WIDE X 16" DIAMETER SMOOTH POLISHED CHROMED CORED ROLLS, SILENT CHAIN DRIVEN, HYDRAULICALLY ACTUATED CLOSURE WITH INTEGRALLY MOUNTED PULL ROLL STAND; FOUR (4) ADVANTAGE SENTRA TEMPERATURE CONTROL UNITS. AEC # 46471001

2011 ZENO ZTLL 1200 X 1600 LOW NOISE GRINDER, CARBON STEEL. FEED OPENING 47" (1200MM) WIDE X 68" (1600MM) LONG. APPROXIMATE 15" (380MM) ROTOR FLIGHT CIRCLE WITH 22 CUTTING INSERTS. ROTOR DRIVEN BY A RATED 34.5 KW (46 HP), 3/60/480 VOLT, 1760 RPM MOTOR. S/N: 10A-5894. AEC # 48826001.

GLOUCESTER 3.5" EXTRUDER, 32:1 L/D, ELECTRICALLY HEATED, WATER COOLED, 150 HP DC MOTOR WITH SCR CONTROLLER, CONTROL PANEL WITH 5 BARRELS, 1 ADAPTER, 1 SCREEN CHANGER, 1 MELT PUMP, 7 DIE ZONES, 3.5" SCREEN CHANGER, SERIAL # 33252-01, 40" EDI SHEET DIE, GLOUCESTER 54" WIDE X 16" DIAMETER THREE ROLL VERTICAL SHEET STACK, CORED ROLLS WITH ROTARY UNIONS WITH COOLING CONVEYOR, GLOUCESTER 54" WIDE PULL ROLL STAND WITH RUBBER PULL ROLLS, GLOUCESTER 3 POSITION WINDER, MODEL 115, SERIAL # 33121-01. ELECECTRIC: 3/60/460V

2001 NGR A-GRAN 65 HD NEXT GENERATION RECYCLING MACHINE 65MM (2.55") SINGLE SCREW EXTRUDER. APPROXIMATE 33 TO 1 L/D RATIO. ELECTRICALLY HEATED, AIR COOLED NON VENTED BARREL. FEED THROAT, NO HOPPER WITH AN APPROXIMATE 15.3" WIDE SINGLE ROLL SHREDDER WITH DUAL PISTON RAM PRESS. WATER COOLED FEED THROAT INTO SCREW. APPROXIMATE 42" CENTERLINE HEIGHT. DRIVEN BY AN APPROXIMATE 55 KW MOTOR THRU A REDUCER. INCLUDES AN OPERATOR CONTROL PANEL WITH A MAGELIS DISPLAY, A MANUAL SCREEN CHANGER, AND A CONTROL PANEL. APPROXIMATE UP TO 100 KILOGRAMS PER HOUR OF PELLET OUTPUT. S/N: Q-01002. AEC # 47562001

DAVIS STANDARD 2-1/2" SINGLE SCREW EXTRUDER. APPROXIMATE 24 TO 1 L/D. 4-ZONE ELECTRICALLY HEATED, AIR COOLED. 3" DIAMETER WATER COOLED FEED THROAT WITH HOPPER. DRIVEN BY A 15 HP, 1750/2300 RPM, 500 VOLT MOTOR. APPROXIMATE 42" CENTER LINE. INCLUDES CONTROL WITH TEMPERATURE CONTROLLERS AND FINCOR 3120M DRIVE. MOUNTED ON A CARBON STEEL BASE. NO MANUFACTURES TAG. S/N: AEC # 51005001

EDI H40 55" WIDE ULTRAFLEX FILM/LAMINATING DIE. END FEED DESIGN. LAST USED FOR POLYSTYRENE FILM ONTO POLYSTYRENE FOAM SHEET. S/N: 40617015

1994 JSW P150-28AWV 150MM (5.9") SINGLE SCREW EXTRUDER. APPROXIMATE 28 TO 1 L/D RATIO. ELECTRICALLY HEATED, WATER COOLED 6 ZONE SIDE VENTED BARREL. INCLUDES A CLOSED LOOP SYSTEM WITH PUMP, TANK, AND HEAT EXCHANGER, AND A SHINKO WATER RING VACUUM PUMP, MODEL SW-150S, DRIVEN BY A 5.5 KW MOTOR. EXTRUDER DRIVEN BY A 75 KW, 440 VOLT, 1160 RPM MOTOR THRU A REDUCER, 4.5 TO 45 RPM OUTPUT. SERIAL # 150137. EXTRUDER SET UP FOR SIDE FEED WITH A JSW TWIN CONICAL FEEDER, MODEL TCF 490S. DRIVEN BY A 11 KW, 3/60/440 VOLT, 1180 RPM MOTOR THRU A REDUCER, RATIO 93.004 TO 1. (1) SEKISUI 150MM HYDRAULIC SCREEN CHANGER, MODEL SPC-150H, SERIAL # 474064, WITH A NACHI 7.5 KW HYDRAULIC POWER PACK. (1) MAAG COREX GEAR PUMP, TYPE CO 70/70, SERIAL # 50010236-10. DRIVEN BY A 11 KW, 3/60/360 VOLT, 1750 RPM MOTOR THRU A REDUCER, RATIO 41 TO 1. INCLUDES A REIKEN OIL HEATER, MODEL RT-12S, SERIAL # RT-94060. (2) JSW REWINDER WITH CART, (1) JSW WINDER. CONTROL PANELS AVAILABLE.

BERINGER 600 HYDRAULIC SLIDE PLATE SCREEN CHANGER. (2) NOMINAL 6" BREAKER PLATES. MOUNTED ON A STAND AND SET UP FOR VERTICAL USE. S/N: 43337004

MELT PUMP. 30 HP UNIT HAS A DIE CART MOUNTED ON THE SAME BASE AND IS INCLUDED WITH THE GEAR PUMP. S/N: 41715012

1990 BATTENFELD GLOUCESTER 36" WIDE INCLINED SHEET EXTRUSION LINE. CONSISTING OF THE FOLLOWING: - 3.5" GLOUCESTER 30/1 L/D VENTED EXTRUDER, MODEL 35250, SERIAL # 33310-01. EXTRUDER IS DRIVEN BY A 150 HP DC MOTOR, DIRECT CONNECTED TO A 15.46/1 GEARBOX. HAS A 3.5" GNEUB HYDRAULICALLY ACTUATED SCREEN CHANGER INCLUDING HYDRAULIC PUMPING SYSTEM AND A TEMPERATURE CONTROL PANEL. HAS ELECTRICALLY HEATED WATER COOLED BARREL, WATER COOLED FEED THROAT AND PUMP AND HEAT EXCHANGER FOR GEARBOX COOLING. INCLUDES CLOSED LOOP WATER COOLING SYSTEM FOR EXTRUDER BARREL AND A DEKKER, TITAN SERIES MODEL 3V0100D-MA3-SGL, SINGLE STAGE LIQUID RING VACUUM PUMP WITH 5.5KW MOTOR, 100 ACFM FOR THE EXTRUDER VENT. -DOWNSTREAM INCLUDES MAAG 56/56 MELT PUMP SERIAL # 8330 63034/2 WITH APPROXIMATELY 10 HP MOTOR, 24" FLEX LIP DIE WITH 45 DEGREE RESTRICTOR BAR AND 30-45 DEGREE DOWN ANGLE ADAPTER. - 3 ROLL CHILL ROLL STACK IS A HYDRAULICALLY LOADED BATTENFELD-GLOUCESTER INCLINED STYLE WITH INDIVIDUALLY DRIVEN 36" WIDE X 16" DIAMETER ROLLS. INCLUDES HYDRAULIC PUMP FOR ROLL PRESSURE. TOP AND BOTTOM ROLL ARE POLISHED CHROME PLATED WHILE CENTER ROLL IS A MATTE FINISH. INCLUDES (3) STERLING TEMPERATURE CONTROL UNITS, COOLING CONVEYOR WITH EDGE TRIM RAZOR SLITTING STATION AND PULL ROLL STAND. - INCLUDES (2) SPARE CHROME ROLLS, (2) SPARE RUBBER ROLLS AND (2) SPARE DAMAGED CHILL ROLLS. AEC # 50221001.

BUSS TCS 100-16 D KO-KNEADER EXTRUDER. 100MM (3.93") DIAMETER HEATED SCREW, 16 TO 1 L/D RATIO. APPROXIMATE 57-1/4" CENTERLINE HEIGHT. (6) JACKETED BARREL SECTIONS, SIDE FEEDER, ALSO HAS TOP CENTER PORT. SCREW DRIVEN BY A 125 HP, 3/60/460 VOLT, 1785 RPM AC MOTOR. HAS (4) REGLOPLAS P160 TEMPERATURE CONTROLLERS. S/N: 452126-1. INCLUDES COOLING CONVEYOR, BELT APPROXIMATE 39-3/8" WIDE X 18 LONG, (2) CORED ROLLS 8" DIAMETER & 16" DIAMETER, NETZSCH-CONDUX SMALL GRANULATOR AT THE END OF THE COOLING CONVEYOR. HAS VAC-U-MAX BULK COLLECTION SYSTEM WITH ROOTS MODEL 33 U-RAI ROTARY LOBE BLOWER, (4) STERLING MODEL M2B2010-D TEMPERATURE CONTROLLERS, STERLING MODEL GRT45-5-4 PUMP TANK. OPERATORS PANEL WITH SIEMENS/MOORE PLC, (6) DOOR CONTROL PANEL WITH ABB ACS 600 MAIN DRIVE, ABB ACS 300 FEEDER DRIVE, SQUARE D TELEMECANIQUE ALTIVAR 18 DRIVE GRANULATOR DRIVE. AEC # 50515002.

1988 OMV 4.5" SINGLE SCREW EXTRUDER. APPROXIMATELY 36 TO 1 L/D. ELECTRICALLY HEATED, WATER COOLED 8 ZONE BARREL. WATER COOLED FEED THROAT WITH 6-1/4" X 6-1/4" TANGENTIAL FEED OPENINGS. APPROXIMATE 54" CENTERLINE HEIGHT. BARREL APPROXIMATELY 172" LONG. MANUAL SCREEN CHANGER. DRIVEN BY A 219KW DC MOTOR. INCLUDES CINCINNATI MILACRON CONTROL PANEL WITH GE FANUC SERIES ONE PLC, PARKER DRIVE, (2) BALDOR VECTOR DRIVES, MISSING TEMPERATURE CONTROLLERS. MOUNTED ON A PAINTED CARBON STEEL FRAME. MACHINE# 00455. AEC # 48907001.

4-1/2'' 30:1 NON VENTED EXTRUDER, WATER COOLED WITH CONTROL PANEL, 250 HP D.C. BALDOR MOTOR, LUFKIN GEARBOX APPROXIMATE 8.5 TO 1. AND 54'' CENTERLINE. (1) 15 HP DYNISCO MELT PUMP. (1) 4.5 '' BERINGER SCREEN CHANGER WITH POWER PAK. (1) DAVIS STANDARD 2.5'' 30:1 WATER COOLED EXTRUDER MFG. IN 1998 WITH BERINGER HYDRAULIC SCREEN CHANGER AND POWER PACK, 60 HP DRIVE AND CONTROLS. (1) COEX FEED BLOCK WITH 30" FLEX LIP DIE. (1) APPROXIMATE 42'' WELEX 3 ROLL SHEET STACK WITH PULL ROLLS AND TEMPERATURE CONTROLS, (3) 18" DIAMETER ROLLS. (2) CART STYLE TORQUE MOTOR REWINDERS WITH DRIVE PEDESTAL.

4.5" MERRIT SINGLE SCREW EXTRUDER 36/1 L/D, VENTED. HAS BELT DRIVEN DIRECT CONNECTED 200 HP DC MOTOR WITH QUANTUM SCR CONTROLLER. MOTOR IS TUCK-UNDER DESIGN DIRECT CONNECTED TO GEARBOX WITH 12.45/1 RATIO, SUPPLYING 140 RPM SCREW SPEED. ELECTRICALLY HEATED WATER COOLED BARREL, 240/480 VOLT AC INPUT. HAS WATER COOLED TOP CENTER FEED THROAT. INCLUDES SPARE SCREW. S/N: 50525002

HOSOKAWA ALPINE 60/140 CL GRANULATOR, CARBON STEEL. AVERAGE THROUGHPUT 3,300 POUNDS PER HOUR DEPENDING ON MATERIALS AND PARTS. APPROXIMATE 23.6" (600MM) X 55.1" (1400MM) THROAT SIZE. TOP FEED HOPPER, MOTOR OPERATED TILT. APPROXIMATE 23" DIAMETER, 4-BLADE OPEN ROTOR, (2) BED KNIVES. SCREEN WITH 5/16" DIAMETER HOLES. MISSING DRIVE MOTOR APPROXIMATE 100/150 HP. INCLUDES CONTROL PANEL. MOUNTED ON A CARBON STEEL FRAME. INCLUDES EXTRA CUTTING BLADES, (2) 1/4" DIAMETER SCREENS, (4) 1/2" DIAMETER SCREENS. S/N: R1128430K1. AEC # 50965003

DAVIS STANDARD SINGLE SCREW EXTRUDER. 30/1 L/D NON-VENTED BARREL IS ELECTRICALLY HEATED AND WATER COOLED, BUT NO WATER SYSTEM MISSING. NO TEMPERATURE CONTROL PANEL. EXTRUDER IS DRIVEN BY A RELIANCE 20 HP DC MOTOR WITH RELIANCE SCR CONTROL. S/N: AEC # 41715011

GALA 4032 BF EASY ACCESS SPIN DRYER. APPROXIMATE 32" DIAMETER X 72" LONG. (4) SCREEN SECTIONS, 1/16" DIAMETER HOLE SIZE. APPROXIMATE CAPACITY PER HOUR: PELLET 35,000, FLAKE: 3,500. ROTOR SPEED 410 RPM. MAXIMUM WATER RATE 200 GPM. 4,000 CFM. MISSING APPROXIMATE 15 HP MOTOR AND BLOWER. SERIAL # 976086. AEC # 50965001.

WELEX CO-EX BLOCK. EQUIPPED WITH (2) INLETS. LAST USED ON A WELEX SHEET LINE WITH A 44'' EDI RC-100 DIE. AEC # 43337001

2006 PTI SWU 50" WIDE S WRAP PULL ROLL ASSEMBLY (2) 24" DIAMETER X 50" WIDE PNEUMATICALLY ADJUSTABLE POLYURETHANE ROLLS, EACH ROLL DRIVEN BY A GEARMOTOR. TOP MOUNTED 6" DIAMETER RUBBER NIP ROLL. S/N: 40617003