Surplus to Ongoing Operations of Major Compressor Mfg

2002 DOOSAN S-310 SML SLANT BED CNC LATHE S/N: L NJ-1039 SPECS. FROM ONLINE SOURCE (PLEASE VERIFY): MAX TURNING DIAMETER: 15.2 MAX SWING OVER BED: 19.7 MAX TURNING LENGTH: 30 MAX BAR CAPACITY: 2.54 X-AXIS TRAVEL: 7.87 Z-AXIS TRAVEL: 29.53 SUB SPINDLE TRAVELS: 26.0 C-AXIS: 360 DEGREE (0.001) ON BOTH SPINDLE X RAPID TRAVERSE RATE: 945 INCH PER MINUTE Z RAPID TRAVERSE RATE: 1181 INCH PER MINUTE SPINDLE BORE: 3.03 SUB SPINDLE BORE: 1.89 MAIN SPINDLE NOSE: A2-8 SUB SPINDLE NOSE: A2-5 MAIN SPINDLE SPEED: 45-4500 RPM SUB SPINDLE SPEED: 45-4500 RPM LIVE TOOL SPEED: 3000 RPM MAIN SPINDLE POWER: 20 HP SUB SPINDLE POWER: 7.5 HP WEIGHT : 14000 LBS APPROX. OVERALL DIMENSIONS: 132 X 73 X 74 HIGH OVERALL DIMENSIONS: 146 X 67 X 74 HIGH WITH CHIP CONVEYOR

2001 TAKISAWA TC-30 CNC LATHE S/N: TLSU1518 FANUC 21I-T CONTROL SPECS FROM ONLINE SOURCE (PLEASE VERIFY): BAR CAPACITY: 2.95" CHUCK SIZE: 10" SPINDLE SPEED: 3,000 RPM SPINDLE MOTOR: 20 HP X AXIS TRAVEL: 6.75" Z AXIS TRAVEL: 23" RAPID RATE Z AXIS: 785 IPM TURRET TOOLS: 12 STATION RAPID RATE X AXIS: 630 IPM MAX TURNING DIA 13" MAX TURNING LENGTH: 20" MAX SWING: 21.25" DIMENSIONS: 132" X 63" X 67" WEIGHT: 11,100 LBS.

2001 TAKISAWA TC-30 CNC LATHE S/N: TLSM478 FANUC 21I-T CONTROL SPECS FROM ONLINE SOURCE (PLEASE VERIFY): BAR CAPACITY: 2.95" CHUCK SIZE: 10" SPINDLE SPEED: 3,000 RPM SPINDLE MOTOR: 20 HP X AXIS TRAVEL: 6.75" Z AXIS TRAVEL: 23" RAPID RATE Z AXIS: 785 IPM TURRET TOOLS: 12 STATION RAPID RATE X AXIS: 630 IPM MAX TURNING DIA 13" MAX TURNING LENGTH: 20" MAX SWING: 21.25" DIMENSIONS: 132" X 63" X 67" WEIGHT: 11,100 LBS.

1996 SUNNEN ML-3500-D AUTOMATIC POWER STROKING HONE S/N: 3Z1-1181 DIA. RANGE (ID) MANUAL STROKING .06-6.5-INCHES DIA. RANGE (ID) POWER STROKING .06-4.0-INCHES AUTOMATIC SIZING 1.25 - 2.0 INCHES STROKE LENGTH .236 - 6.7 INCHES MOTOR 5.5 H.P. SPEED 200-3000 RPM

2008 KENT KTM 4VKF MANUAL MILL 10" X 50" TABLE X-AXIS 34 Y-AXIS 16 Z-AXIS 16 QUILL TRAVEL 5 RAM TRAVEL 24 MOTOR 3 HP (1750 RPM @ 60 HZ) SPEED 80-500-420 (2 RANGE, HI/LOW) TAPER R-8 QUILL DIA 3.375 FEED RATE 0.0015/0.003/0.006 PER REV POWER 220 VOLTS/ 3 PHASE/ 60 HZ/ 10 AMP S/N: 029769 ACU-RITE 2 AXIS DRO

1995 MORI SEIKI CL-25A CNC LATHE SPECS FROM ONLINE SOURCE (PLEASE VERIFY): CHUCK SIZE: 10" SWING: 20.5" TURNING DIAMETER: 17.6" CENTER DISTANCE: 17.5" BAR CAPACITY: 1.57" X AXIS TRAVEL: 10.2" Z AXIS TRAVEL: 19.7" SPINDLE SPEED (RPM): 3000 TURRET CAPACITY: 10 REAR DISCHARGE CHIP CONVEYOR NO TAILSTOCK NO Y AXIS DIMENSIONS (APP): 84" X 70" X 85" WEIGHT: 9000 LBS. S/N: 351 MORI SEIKI MF-T8 (FANUC) CONTROL

1980 ROYAL WL-435 17" X 36" MANUAL LATHE S/N: 9-8006.51 12" 4-JAW CHUCK INCLUDED

2006 HYSTER S50XM 5,000 LB. FORKLIFT S/N: D187V15370W LIFT CAPACITY: 5,000 LBS. HOURS: 8,059 TIRE TYPE: HARD FUEL TYPE: PROPANE TRANSMISSION TYPE: AUTOMATIC ENGINE: GM 3.0L # OF STAGES ON MAST: 3 (16') MAST HEIGHT (LOWERED): 83" MAST WIDTH: MAX LIFT HEIGHT: FORK LENGTH: 48" DIMENSIONS: APP WEIGHT: THERE ARE SOME ISSUES WITH THE HYDRAULIC DRIVE. IT WILL START AND YOU CAN DRIVE WITH PRECAUTION.

1986 METAL MUNCHER MM35GB 35 TON HYDRAULIC IRON WORKER S/N: 5103786

SOLBERGA SE-725 GEAR HEAD DRILL PRESS 2 SPEED GEAR DRIVE 20" SWING 18" X 18" TABLE S/N: 5534

DEKA HRG-1222-18 MULTI SPINDLE DRILL PRESS S/N: HRGD2276.15 SPECS FROM ONLINE SOURCE (PLEASE VERIFY): 16 SPINDLE DRILLING CAP. MILD STEEL: (18-SPINDLES) - 13/32" (10-SPINDLES) - 5/8" (5-SPINDLES) - 7/8" CAST IRON: (18-SPINDLES) - 1/2" (10-SPINDLES) - 25/32" (5-SPINDLES) - 15/16" TAPPING CAP. MILD STEEL: (18-SPINDLES) - 3/8" - 24 N.F. (12-SPINDLES) - 9/16" - 18 N.F. (6-SPINDLES) - 1" - 14 N.F. CAST IRON: (18-SPINDLES) - 1/2" - 13 N.C. (10-SPINDLES) - 3/8" - 11 N.C. (7-SPINDLES) - 7/8" - 9 N.C. FEED STROKE OF TABLE: 6" MAX. DISTANCE, HEAD FLANGE TO TABLE: 40" (WITH 12" RISER) MIN. DISTANCE, HEAD FLANGE TO TABLE: 26" (WITH 12" RISER) OPENING OF HEAD: 14-1/2"FB X 22-3/4"LR CENTER OF HEAD TO FACE OF WAYS ON COLUMN: 12" NUMBER OF SPINDLE DRIVES: 18 WORKING SURFACE OF TABLE: 19-3/4"FB X 29-1/2"LR STANDARD FEEDING STROKE: 6" MAX. FEEDING PRESSURE: 9000 LBS. FEED RANGE: 0 TO 90 IPM RAPID TRAVERSE RATE: 120 IPM 12-SPINDLE SPEEDS: 174 TO 1562 RPM SIZE OF HEXAGON DRIVES: 9/16" WEIGHT: 4,500 LBS. (APP.) DIMENSION: L X W X H: 58" X 46" X 124"

1978 STUDER OC CYLINDRICAL GRINDER CENTER HEIGHT 3.15 INCHES BETWEEN CENTERS 15.75 INCHES STROKE .039-16.54 INCHES SPEED STEPLESSLY VARIABLE .4-11.5 FT./MIN. MAX SWIVEL OF TOP TABLE 30 DEG WORKHEAD SPEED STEPLESSLY VARIABLE 60-1200_MIN-1 MOTOR 0,3 KW SPINDLE NOSE - MORSE 2 WHEELHEAD GRINDING WHEEL DIAMETER 12 INCHES WIDTH 1.18 INCHES BORE 5 INCHES MOTOR 2,2 KW S/N: 230-9

1932 TAKISAWA TSL-800-D MANUAL LATHE 8 INCH 3-JAW CHUCK 14" SWING 30" CENTERS S/N: BFE910044H