Bakery Processing and Packaging Equipment Auction

SIGMA Auction

Category: PACKAGING EQUIPMENT

Total Lots: 350

Total Sales: 🔒 Subscribe

Lot Price Distribution

🔒

Subscribe to view

Unlock price distribution and full auction analytics

Sort:

Showing 251–300 of 350 lots

Make	Model	Lot Description	Hammer Price
EDL PACKAGING ENGINEERS	MULTIPACKER AND BUNDLER	EDL PACKAGING ENGINEERS NON-REGISTERED UNSUPPORTED MULTIPACKER AND BUNDLER WITH 90-DEGREE INFEED - USED EDL PACKAGING ENGINEERS MULTIPACKER AND BUNDLER WITH: 90... INFEED CONVEYOR WIDTH: 6 INCHES ADJUSTABLE HEIGHT SIDE RAILS FILM WIDTH: 20.125 INCHES HEAT SEAL JAW WIDTH: 26.5 INCHES PUSH ARM WIDTH: 16.25 INCHES HEAT TUNNEL APERTURE: WIDTH: 26.5 INCHES HEIGHT: 16.5 INCHES LEFT-TO-RIGHT OPERATION PLASTIC-TOP DISCHARGE CONVEYOR ELECTRICAL REQUIREMENTS: 277/480 VOLTS 60 HZ 3 PHASE ADJUSTABLE HEIGHT LEVELING LEGS PAINTED STEEL CONSTRUCTION LAST BUNDLING (4) 16-OUNCE AND (4) 32-OUNCE BAGS OF COFFEE EDL PACKAGING ENGINEERS · MULTIPACKER AND BUNDLER	🔒 Subscribe
GROEN	D-60	GROEN D-60 60 GALLON HALF JACKETED STAINLESS STEAM KETTLE - USED GROEN D-60 STEAM KETTLE WITH: CAPACITY: 60 GALLONS DIMENSIONS: DIAMETER: 30 INCHES DEPTH: 25 INCHES HALF JACKETED: 25 PSI AT 300... F HAND CRANK TILT STAINLESS STEEL CONSTRUCTION GROEN · D-60	🔒 Subscribe
MIDDLEBY MARSHAL	PS360WB	MIDDLEBY MARSHAL PS360WB OVEN - USED MIDDLEBY MARSHAL OVEN WITH: INFEED: LENGTH: 53 INCHES WIDTH: 41 INCHES HEIGHT: 5 INCHES OVEN ACCESS PANEL WITH VIEWING GLASS: LENGTH: 38 INCHES HEIGHT: 5 INCHES PUSH BUTTON CONTROLS DIGITAL TEMPERATURE READOUT ELECTRICAL: 240 VOLTS, 1 PH, 60 HZ REQUIRES BELT MIDDLEBY MARSHAL · PS360WB	🔒 Subscribe
MIDDLEBY MARSHAL	PS360WB	MIDDLEBY MARSHAL PS360WB OVEN - USED MIDDLEBY MARSHAL OVEN WITH: INFEED: LENGTH: 53 INCHES WIDTH: 41 INCHES HEIGHT: 5 INCHES OVEN ACCESS PANEL WITH VIEWING GLASS: LENGTH: 38 INCHES HEIGHT: 5 INCHES PUSH BUTTON CONTROLS DIGITAL TEMPERATURE READOUT ELECTRICAL: VOLTS: 240 FREQUENCY: 60 HZ PHASE 1 NO BELT MIDDLEBY MARSHAL · PS360WB	🔒 Subscribe
		64" L X 33" W TRANSFER CONVEYOR - USED TRANSFER CONVEYOR: CONVEYOR DIMENSIONS: LENGTH: 64 INCHES WIDTH: 33 INCHES INFEED HEIGHT: 24 INCHES DISCHARGE HEIGHT: 24 INCHES	🔒 Subscribe
B+ EQUIPMENT (SEALED AIR)	I-PACK BA24B-2	B+ EQUIPMENT (SEALED AIR) I-PACK BA24B-2 GLUE BOTTOM SEAL CASE ERECTOR - USED CASE ERECTOR WITH: MINIMUM CASE DIMENSIONS: LENGTH: 7 INCHES WIDTH: 5.5 INCHES HEIGHT: 0.75 INCHES MAXIMUM CASE DIMENSIONS: LENGTH: 35 INCHES WIDTH: 23.5 INCHES HEIGHT: 23.5 INCHES LAST RUN CASE DIMENSIONS: LENGTH: 10.75 INCHES WIDTH: 6.5 INCHES HEIGHT: 6.5 INCHES MAGAZINE DIMENSIONS: LENGTH: 33 INCHES WIDTH: 12 INCHES PUSH BUTTON CONTROLS ELECTRICAL REQUIREMENTS: 400 VOLTS, 50 HERTZ, 3 PHASE OVERALL DIMENSIONS: LENGTH: 9 FEET WIDTH: 6 FEET HEIGHT: 6 FEET B+ EQUIPMENT (SEALED AIR) · I-PACK BA24B-2	🔒 Subscribe
REVENT	619 G DG	REVENT 619 G DG 318,000 BTU NATURAL GAS-FIRED DOUBLE RACK OVEN - USED REVENT 619G DG DOUBLE RACK OVEN WITH: CAPACITY: DOUBLE RACK BTU: 318,000 FUEL: NATURAL GAS TIMERS DIGITAL TEMPERATURE READ OUTS DOUBLE PANE VIEWING WINDOW STAINLESS STEEL CONSTRUCTION ELECTRICAL: 208 VOLTS, 60 HZ, 3 PHASE, 15 AMPS REVENT · 619 G DG	🔒 Subscribe
FORMOST FUJI	FW3400A-5	FORMOST FUJI FW3400A-5 HORIZONTAL FLOW WRAPPER - USED FORMOST FUJI FW3400A-5 FLOW WRAPPER WITH: PRINT REGISTERED HORIZONTAL FLOW WRAPPER INFEED LENGTH: 100 INCHES MANUAL PRODUCT LOAD LUGGED INFEED LUG CENTERS: 14 INCHES FILM WIDTH: 17 INCHES AUTOMATIC FILM SPLICING ROTARY LONGITUDINAL FIN SEAL TOUCH SCREEN HMI LEFT TO RIGHT PRODUCT FLOW STAINLESS STEEL CONTACT PARTS PAINTED, MILD STEEL FRAME LAST USED FOR BAGELS FORMOST FUJI · FW3400A-5	🔒 Subscribe
MATRIX	PROTEUS 2840SER	[MATRIX PROTEUS 2840ER VERTICAL FORM FILL SEAL] SEAL JAW LENGTH: 12 INCHES MAXIMUM FILM WIDTH: 22 INCHES FORMER: DSL FORMING COLLAR DIAMETER: 2.5 INCHES PILLOW BAGS PRINT REGISTRATION DISCHARGE HEIGHT: 20 INCHES MARKEM SMART DATE 2 DATE CODER ALLEN-BRADLEY PANELVIEW PLUS 1000 TOUCHSCREEN HMI FORMING COLLAR MAKES A LEFT OVER RIGHT FIN SEAL S/N: 75361DSL MATRIX · PROTEUS 2840SER	🔒 Subscribe
		ROTATING CENTER CIRCULAR TABLE WITH 20 INCH SPIKES - USED TABLE WITH: CIRCULAR DIAMETER: 84 INCHES WORKING HEIGHT: 34 INCHES MANUALLY ROTATING CENTER: DIAMETER: 60 INCHES PLACEMENT SPIKES: LENGTH: 20 INCHES	🔒 Subscribe
VESTIL	TMS-20-DC	VESTIL MANUFACTURING TMS-20-DC TILT MASTER STRADDLE PALLET LIFT - USED VESTIL PALLET JACK WITH: CAPACITY: 2000 POUNDS FORK DIMENSIONS: LENGTH: 35 INCHES WIDTH: 4 INCHES FORK ADJUSTMENT I.D: MINIMUM: 0.5 INCHES MAXIMUM: 28.5 INCHES MAXIMUM TILT: 90 DEGREES LOAD CENTER: 18 INCHES WHEEL TYPE: PHENOLIC ROTATED HEIGHT: 37 INCHES LOWERED HEIGHT: 3 INCHES OVERALL DIMENSIONS: WIDTH: 57.25 INCHES DEPTH: 73.25 INCHES HEIGHT: 29.25 INCHES PAINTED STEEL CONSTRUCTION ELECTRICAL: 12 VOLT DC, 140 FULL LOAD AMPS PREVIOUSLY USED IN POPCORN FACILITY VESTIL · TMS-20-DC	🔒 Subscribe
		64" L X 33" W TRANSFER CONVEYOR - USED TRANSFER CONVEYOR: CONVEYOR DIMENSIONS: LENGTH: 64 INCHES WIDTH: 33 INCHES INFEED HEIGHT: 17 INCHES DISCHARGE HEIGHT: 17 INCHES	🔒 Subscribe
LAUDENBERG	FBL 22 HFFS	[LAUDENBERG FBL 22 HFFS] ROTARY HORIZONTAL POUCH FORM FILL SEALER WITH ZIPPER - USED LAUDENBERG FBL 22 HFFS POUCH MACHINE WITH: INTERMITTENT, ROTARY HORIZONTAL POUCH FORMING, FILLING, AND SEALING MACHINE FORMS AND FILLS POUCH UPSIDE DOWN, TOP OF THE FINISHED POUCH IS SEALED FIRST POUCH DIMENSIONS: MINIMUM: 4.72 INCHES WIDE X 3.93 INCHES LONG MAXIMUM: 7.4 INCHES WIDE X 13 INCHES LONG CURRENT POUCH SIZE: APPROXIMATELY 6 INCHES WIDE X 11 INCHES LONG CURRENT FILM WIDTH: 22 INCHES OUTPUT: UP TO 200 POUCHES PER MINUTE, DEPENDING ON PRODUCT, FILL METHOD, AND POUCH SIZE RESEALABLE ZIPPER APPLICATOR GAS FLUSH PRINT REGISTRATION POUCH HANGER HOLE PUNCH SERVO MOTOR DRIVEN FOOD GRADE, STAINLESS STEEL CONSTRUCTION LAUDENBERG · FBL 22 HFFS	🔒 Subscribe
		64" L X 33" W TRANSFER CONVEYOR - USED TRANSFER CONVEYOR: CONVEYOR DIMENSIONS: LENGTH: 64 INCHES WIDTH: 33 INCHES INFEED HEIGHT: 24 INCHES DISCHARGE HEIGHT: 24 INCHES S/N:	🔒 Subscribe
KEY TECHNOLOGY	ISO-FLO 211	KEY TECHNOLOGY ISO-FLO 211"L X 18"W STAINLESS STEEL VIBRATORY CONVEYOR - USED KEY TECHNOLOGY VIBRATORY CONVEYOR WITH: CONVEYOR DIMENSIONS: LENGTH: 211 INCHES WIDTH: 18 INCHES DISCHARGE HEIGHT: 65.5 INCHES STAINLESS STEEL CONSTRUCTION MOUNTED ON 8 INCH CASTERS ELECTRICAL: 460 VOLTS, 60 HERTZ, 3 PHASE KEY TECHNOLOGY · ISO-FLO 211	🔒 Subscribe
STRATASYS	CONNEX 350	[STRATASYS CONNEX 350] 3D PRINTER USES SPECIAL TECHNOLOGY TO PRINT MODELS SIMULTANEOUSLY WITH DIFFERENT MODEL MATERIALS. PRINTING MODELS WITH COMBINATIONS OF BASIC MATERIALS (DIGITAL MATERIALS) ENABLES YOU TO CHOOSE FROM A WIDE RANGE OF MECHANICAL PROPERTIES?FROM FLEXIBLE TO RIGID?AND COLORS. IT IS ALSO CAPABLE OF PRINTING MODELS MADE FROM DIFFERENT MATERIALS ON THE SAME BUILD TRAY IN THE SAME PRINT JOB AND QUICKLY ALTERNATING BETWEEN PRINTING JOBS USING THE MODEL MATERIALS LOADED. USED STRATASYS OBJET 350 3D PRINTER WITH: BUILD AREA DIMENSIONS (INCHES): LENGTH: 13.4 WIDTH: 13.4 HEIGHT: 7.9 RESOLUTION (DOTS PER INCH): X-AXIS: 600 DPI Y-AXIS: 600 DPI Z-AXIS: 1,600 DPI OVERALL DIMENSIONS (INCHES): LENGTH: 55.1 WIDTH: 49.6 HEIGHT: 43.4 MINIMUM LAYER THICKNESS (HORIZONTAL BUILD LAYERS): 16 MICRONS (0.0006 INCH) BUILD MODE RESOLUTIONS: DIGITAL MATERIAL: 30-MICRON (0.001 INCH) HIGH QUALITY: 16-MICRON (0.0006 INCH) HIGH SPEED: 30-MICRON (0.001 INCH) NETWORK CONNECTIVITY: LAN - TCP/IP OPERATING CONDITIONS: 64...F TO 77...F; RELATIVE HUMIDITY 30 TO 70% CE LISTED POWER: 110-240 VAC, 50/60 HZ, 1.5 KW, SINGLE PHASE STRATASYS · CONNEX 350	🔒 Subscribe
		USED PALLET OF MRO PALLET INCLUDES MRO PARTS FOR BUCKET CHECK WEIGHER DIAMETER OF CLEAR PLASTIC FUNNEL: 16 INCHES OVERALL DIMENSIONS: LENGTH: 40 INCHES WIDTH: 48 INCHES HEIGHT: 33 INCHES	🔒 Subscribe
VULCAN HART	ET88	VULCAN HART ET88 OVEN WITH: ELECTRICAL REQUIREMENTS: 480 VOLTS, 60 HERTZ, 3 PHASE VULCAN HART · ET88	🔒 Subscribe
PACKRITE	6000-4240-000	[USED] PACKRITE 6000-4240-000 CONTINUOUS BAND BAG SEALER WITH: PRODUCT FLOW: RIGHT TO LEFT SEAL WIDTH: .75 OF AN INCH DIGITAL TEMPERATURE CONTROLS VARIABLE SPEED: UP TO 750 INCHES PER MINUTE TEFLON FABRIC BANDS MAXIMUM TEMPERATURE: 600 DEGREES FAHRENHEIT ADJUSTABLE WORKING HEIGHT PACKRITE · 6000-4240-000	🔒 Subscribe
BOSCH DOBOY	LINIUM 301	BOSCH DOBOY LINIUM 301 PRINT REGISTER FLOW WRAPPER WITH: APPLICATION: DESIGNED TO FLOW WRAP PRODUCTS WITH PRINT REGISTERED FILM OUTPUT: UP TO 150 PACKAGES PER MINUTE PRODUCT SIZE RANGE: MINIMUM (INCHES): 3.5 LONG X 0.4 WIDE MAXIMUM (INCHES): 7.25 LONG X 6.9 WIDE MAXIMUM HEIGHT (WITH PROPER CHANGE PARTS): 2.5 INCHES BOSCH INFEED SERIAL: 05-25838 INFEED LENGTH: 97 INCHES INFEED BELT WIDTH: 5 INCHES LUGGED INFEED LUG CENTER SET: 10 INCHES PRINT REGISTRATION: EYE PACKAGING MATERIALS: PRINTED OR UNPRINTED HEAT SEALABLE POLYPROPYLENES LAMINATES FILM SPECS: MAXIMUM WIDTH: 23.6 INCHES MAXIMUM REEL DIAMETER: 15.7 INCHES ON 3 INCH CORE 1 UP CRIMP VERTICAL SEAL: 9 INCHES WIDE BOSCH DOBOY · LINIUM 301	🔒 Subscribe
RYSON	NT1100-150-B441/4	RYSON NT1100-150-B441/4 DECLINING SPIRAL ELEVATOR CONVEYOR - USED RYSON SPIRAL CONVEYOR WITH: CONVEYOR WIDTH: 6 INCHES WEIGHT CAPACITY: 50 POUNDS PER LINEAR FOOT TOTAL WEIGHT: UP TO 3600 POUNDS SPEED: UP TO 200 FEET PER MINUTE DEPENDING ON PRODUCT AND APPLICATION DISTANCE BETWEEN TIERS: 15.25 INCHES PRODUCT CLEARANCE: 13 INCHES INFEED HEIGHT: 96 INCHES DISCHARGE HEIGHT: 34 INCHES OUTSIDE DIAMETER: 50 INCHES CENTERLINE DIAMETER: 44 INCHES OVERALL DIMENSIONS: DIAMETER: 50 INCHES HEIGHT: APPROXIMATELY 100 INCHES DRIVE MOTOR: 2 HORSEPOWER ELECTRICAL: 3 PHASE, 60 HZ, 230/460 VOLTS PREVIOUSLY USED IN POPCORN FACILITY RYSON · NT1100-150-B441/4	🔒 Subscribe
AM MANUFACTURING	ROUND-O-MATIC R-900C	AM MANUFACTURING ROUND-O-MATIC R-900C DOUGH ROUNDER WITH: PRODUCTION RATE: UP TO 72000 PIECES PER HOUR, DEPENDING ON APPLICATION PRODUCTION RANGE: MINIMUM: 1 OUNCE MAXIMUM: 2.5 POUNDS CONVEYOR DIMENSIONS: LENGTH: 18.5 INCHES WIDTH: 12 INCHES HIEGHT UNDER CONVEYOR: 32.75 INCHES STAINLESS STEEL CONSTRUCTION ELECTRICAL REQUIREMENTS: 240 VOLTS, 60 HERTZ, 3 PHASE OVERALL DIMENSIONS: LENGTH: 47 INCHES WIDTH: 24 INCHES HEIGHT: 42.5 INCHES AM MANUFACTURING · ROUND-O-MATIC R-900C	🔒 Subscribe
ULMA	FLORIDA	[ULMA FLORIDA] HORIZONTAL, AUTOMATIC, 1-UP, PRINT REGISTERED, FLOW WRAPPER - USED ULMA FLORIDA HORIZONTAL FLOW WRAPPER WITH: SPEED: UP TO 150 PACKAGES PER MINUTE DIRECTION OF TRAVEL: LEFT TO RIGHT PRINT REGISTRATION EYE DATA SENSOR TLU-115 FILM WIDTH: 500 MILLIMETERS MANDRIL DIAMETER: 76 MILLIMETERS MAXIMUM REEL DIAMETER: 300 MILLIMETERS MAXIMUM PRODUCT DIMENSIONS: WIDTH: 250 MILLIMETERS 9.84 INCHES HEIGHT: 70 MILLIMETERS 2.75 INCHES MINIMUM PRODUCT DIMENSIONS: WIDTH: 10 MILLIMETERS .39 INCHES HEIGHT: 5 MILLIMETERS .20 INCHES ROTARY CROSS SEALING JAWS SELF CENTERING REEK HOLDER WITH BRAKE SYSTEM 70 INCH LONG PRODUCT INFEED CONVEYOR 1 INCH X 1 INCH PLASTIC LUGS 16 INCH CENTERS DISCHARGE HEIGHT: 30 INCHES ADJUSTABLE FILM FOLDING BOX (3) PAIRS OF ROLLERS FOR LONGITUDINAL FILM PULLING AND SEALING AIR CONSUMPTION: 50 LITERS PER MINUTE AT 6 BAR ELECTRICAL REQUIREMENTS: 220 VOLTS, 60 VOLTS, 3 PHASE ULMA · FLORIDA	🔒 Subscribe
ISHIDA	CCW-Z-212P-D/08-BP	ISHIDA HEAT AND CONTROL CCW-Z-212P-D/08-BP COMPUTER COMBINATION WEIGHER WITH: 12 WEIGHING HEADS WEIGHING METHOD: PAIR DISCHARGE METHOD: DOUBLE - PRODUCTS DISCHARGE SEPARATELY VIA A 2-TUBE, DOUBLE CHUTE HOPPER VOLUME: 800CC PAINTED BODY WEIGHING CAPACITY: 1000 GRAMS WEIGHING RANGE: 14 TO 1000 GRAMS ACCURACY: < 2.0 GRAMS WEIGHING SPEED: 140 WEIGHS PER MINUTE (70 WEIGHS PER MINUTE, PER SIDE), DEPENDS ON PRODUCT SHAPE, DENSITY, TARGET WEIGHT, ETC 16-BIT MICROPROCESSOR CONTROLLER SMOOTH WEIGH BUCKETS ISHIDA · CCW-Z-212P-D/08-BP	🔒 Subscribe
INGERSOLL RAND	SSR-EP40SE	INGERSOLL RAND SSR-EP40SE ROTARY SCREW AIR COMPRESSOR - USED INGERSOLL RAND ROTARY SCREW AIR COMPRESSOR WITH: CAPACITY: 163 CFM RATED OPERATING PRESSURE: 125 PSIG MAXIMUM DISCHARGE PRESSURE: 128 PSIG MAXIMUM MODULATE PRESSURE: 128 PSIG NOMINAL DRIVE MOTOR: 40 HORSEPOWER ELECTRICAL REQUIREMENTS: 230/460 VOLTS, 60 HERTZ, 3 PHASE INGERSOLL RAND · SSR-EP40SE	🔒 Subscribe
YAMATO	4RGB	21 YAMATO 4RGB WEIGH ACTUATOR UNIT, (2) ALLEN BRADLEY CONTROL LOGIX 8 AXIS SERCOS SERVO MODULE. OVERALL DIMENSIONS: LENGTH: 48 INCHES WIDTH: 40 INCHES HEIGHT: 37 INCHES YAMATO · 4RGB	🔒 Subscribe
MIDDLEBY MARSHAL	PS360WB	MIDDLEBY MARSHAL PS360WB OVEN - USED MIDDLEBY MARSHAL OVEN WITH: INFEED: LENGTH: 53 INCHES WIDTH: 41 INCHES HEIGHT: 5 INCHES OVEN ACCESS PANEL WITH VIEWING GLASS: LENGTH: 38 INCHES HEIGHT: 5 INCHES PUSH BUTTON CONTROLS DIGITAL TEMPERATURE READOUT ELECTRICAL: VOLTS: 240 FREQUENCY: 60 HZ PHASE 1 NO BELT MIDDLEBY MARSHAL · PS360WB	🔒 Subscribe
PIZZAMATIC	SMOOTH TOP CONVEYOR	PIZZAMATIC SMOOTH TOP CONVEYOR 180 DEGREE 26" W - USED PIZZAMATIC SMOOTH TOP CONVEYOR WITH: CONVEYOR WIDTH: 26 INCHES 180 DEGREE TURN SMOOTH TOP CONVEYOR BELT STAINLESS STEEL CONSTRUCTION VARIABLE FREQUENCY DRIVE WELDED TUBULAR FRAME CASTERS PIZZAMATIC · SMOOTH TOP CONVEYOR	🔒 Subscribe
FOODTOOLS	CS-4AAC	USED FOODTOOLS CS-4AAC SEMI-AUTO ROUND CAKE PORTIONER WITH: SPEED: UP TO 150 PRODUCTS PER HOUR PRODUCT SIZES: 6 TO 12 INCH DIAMETER UP TO 6.5 INCHES TALL PORTION SIZES: 4 TO 24 PORTIONS PRODUCT TYPE: ROUND PRODUCT TEMPERATURE: FROZEN, CHILLED, HARD STAINLESS STEEL BLADE MANUAL FEED DIVIDER INSERTS AIR REQUIREMENTS: COMPRESSED AIR 5 CFM AT 90 PSI OVERALL DIMENSIONS: 27 INCHES LONG X 21 INCHES WIDE X 54 INCHES TALL FOODTOOLS · CS-4AAC	🔒 Subscribe
RHEON	37" WIDE GUILLOTINE CUTTING LINE SYSTEM	RHEON GRAVIMETRIC 37" WIDE GUILLOTINE CUTTING LINE SYSTEM WITH: RHEON GUILLOTINE CUTTER 37" WIDE TIMING CONVEYOR SYSTEM: 18.5" LONG X 39.5" WIDE TOP HOLD DOWN CONVEYOR: 32" LONG X 9.5" WIDE RHEON FORMING CONVEYOR INFEED HEIGHT: 38" INFEED LENGTH: 61" OUTFEED CONVEYOR: 14' LONG X 39" WIDE (2) TWO TOP FLOUR DUSTER BOTTOM PAN FEEDING CONVEYOR: 39" WIDE X 40' LONG WORKING HEIGHT OF BOTTOM PAN FEEDER: 26" RHEON WATER SPRAY SYSTEM RHEON SEEDING CONVEYOR RHEON PANNING CONVEYOR RHEON SEPARATING CONVEYOR TOUCH SCREEN CONTROLLER: GOT200 ELECTRICAL REQUIREMENTS: 220 VOLTS / 3 PHASE / 60 HERTZ APPROXIMATE OVERALL DIMENSIONS: 59' LONG X 6' WIDE X 7' TALL RHEON · 37" WIDE GUILLOTINE CUTTING LINE SYSTEM	🔒 Subscribe
		66" L X 36" W TRANSFER CONVEYOR - USED TRANSFER CONVEYOR: CONVEYOR DIMENSIONS: LENGTH: 66 INCHES WIDTH: 36 INCHES INFEED HEIGHT: 24 INCHES DISCHARGE HEIGHT: 24 INCHES MOTOR: 2 HORSEPOWER, 208-230/460 VOLTS, 5.7-5.4/2.7 AMPS, 60 HERTZ, 3 PHASE	🔒 Subscribe
R&R MACHINERY MOVERS	BARREL LIFT	BARREL LIFT R&R MACHINERY MOVERS · BARREL LIFT	🔒 Subscribe
CROWN	DMT-40	CROWN DMT-40 DIRECT STEAM TILTING KETTLE WITH: CAPACITY: 40 GALLONS STAINLESS STEEL CABINET M.D.M.T. 32 DEGREES FAHRENHEIT AT 35 PSI 316 STAINLESS STEEL LINER 6 INCH ADJUSTABLE HOLD DOWN FEET ONE PIECE COVER 2 INCH TANGENT DRAW OFF VALVE STEAM CONTROL VALVE AND STEAM TRAP SWING DRAIN HOT AND COLD DECK MOUNT FAUCET HYDRAULIC TILT PAN CARRIER CROWN · DMT-40	🔒 Subscribe
AMF	K	[AMF] MODEL K STAINLESS STEEL VOLUMETRIC DOUGH DIVIDER HEADS (3) - USED AMF DOUGH DIVIDER HEADS (3) WITH: SPEED: BETWEEN 40 AND 100 CUTS PER MINUTE DEPENDING ON PRODUCT AND APPLICATION CUT CAPACITY: MINIMUM: 0.75 OUNCES MAXIMUM: 4.25 OUNCES PISTON DIAMETER: 2 INCHES NUMBER OF PISTONS: 6 PISTON CENTERS: 4.25 INCHES APPROXIMATE OVERALL DIMENSIONS: WIDTH: 35 INCHES DEPTH: 30 INCHES HEIGHT: 34 INCHES STAINLESS STEEL CONSTRUCTION PREVIOUSLY USED IN BAKERY APPLICATION AMF · K	🔒 Subscribe
		STAINLESS STEEL 3" W X 70" L TABLE-TOP CONVEYOR - USED STAINLESS STEEL CONVEYOR WITH: CONVEYOR DIMENSIONS: 3 INCHES WIDE X 70 INCHES LONG CONVEYOR HEIGHT: 37 INCHES 1 HORSEPOWER MOTOR STAINLESS STEEL FRAME SCREW DOWN LEVELING FEET	🔒 Subscribe
DONALDSON TORIT	VS 1200 QD	DONALDSON TORIT VS 1200 QD WITH: 6 INCH INLET 1200 CUBIC FEET PER MINUTE 3 HORSEPOWER MOTOR PAINTED STEEL CONSTRUCTION ELECTRICAL REQUIREMENTS: 460 VOLTS, 60 HERTZ, 3 PHASE APPROXIMATE OVERALL DIMENSIONS: LENGTH: 80 INCHES WIDTH: 39 INCHES HEIGHT: 40 INCHES DONALDSON TORIT · VS 1200 QD	🔒 Subscribe
CASE	BELT CONVEYOR	2002 CASE BELT CONVEYOR 36" LONG X 6" WIDE WITH GUIDE RAILS - USED CASE BELT CONVEYOR WITH: CONVEYOR DIMENSIONS: 36 INCHES LONG X 6.25 INCHES WIDE PRODUCT GUIDE RAILS CASE · BELT CONVEYOR	🔒 Subscribe
		USED INDUCTION SEALER WITH FLAT SEALING HEAD: LENGTH: 26 INCHES WIDTH: 5 INCHES HAND CRANK HEIGHT ADJUSTMENT PUSH BUTTON CONTROLS DIGITAL READOUT AIR COOLED ELECTRICAL REQUIREMENTS: 208/240 VOLTS, 60 HERTZ, 1 PHASE MOUNTED ON CASTERS	🔒 Subscribe
DOMINO	A320I	2015 DOMINO A320I STAINLESS STEEL INK JET CODER WITH: MAX NUMBER OF UNICODE CHARACTERS PER LINE: 255 MAX NUMBER OF LINES: 4 MAX NUMBER OF MESSAGES PER STORE: 256 MAX NUMBER OF STORES PER PRINTER: 16 MAX LINE SPEED: 325 METERS PER MINUTE CONDUIT LENGTH: 3 METERS BEND RADIUS: 100 MILLIMETERS TOUCH SCREEN HMI STAINLESS STEEL CONSTRUCTION ELECTRICAL REQUIREMENTS: 240 VOLTS 60 HZ SINGLE PHASE 4 AMPS DOMINO · A320I	🔒 Subscribe
CREMER	TQI-4150	[USED] CREMER TQI-4150 MULTI-CHANNEL COUNTING SYSTEM WITH (3) OSE CLEATED INCLINE CONVEYORS AND Z-FRAME BUCKET ELEVATOR. POUCH BLENDING AND COUNTING SYSTEM, PREVIOUSLY USED TO COUNT AND ASSEMBLE A 6-COUNT VARIETY PACK OF POUCHED SNACKS AND FEED THE POUCHES TO A CARTONER FOR PACKAGING. (3) OSE CLEATED INCLINE CONVEYORS WITH INFEED HEIGHTS OF 50 AND 86.5 INCHES, CONVEYOR WIDTH OF 13.5 INCHES, INFEED LENGTH OF 132 INCHES, CLEAT CENTERS OF 9 INCHES, CLEAT WIDTH OF 12 INCHES, CLEAT HEIGHT OF 3 INCHES, AND DISCHARGE HEIGHT OF 138 INCHES. INCLINE CONVEYORS FEED INTO TQI-4150 COUNTERS. (3) TQI-4150 MULTI-CHANNEL COUNTERS DETERMINE HOW MANY POUCHES GO INTO EACH BATCH, FEATURING A RE-CIRCULATION SYSTEM THAT RETURNS MIS-ALIGNED POUCHES FROM THE COUNTING PROCESS TO THE INFEED INCLINE CONVEYOR. COUNTERS FEED INTO A Z-FRAME BUCKET CONVEYOR WHICH ULTIMATELY DISCHARGES THE BATCHED POUCHES. BUCKET DIMENSIONS: 13.5 INCHES WIDE X 7 INCHES LONG X 6.5 INCHES DEEP. FINAL PRODUCT DISCHARGE HEIGHT: 83 INCHES. PREVIOUSLY USED IN CONJUNCTION WITH A TRIANGLE VCM-E30-1000-90HS0 VERTICAL GLUE CARTONER. OVERALL SYSTEM HEIGHT: 186 INCHES. CREMER · TQI-4150	🔒 Subscribe
MARCHANT SCHMIDT	334152043	MARCHANT SCHMIDT 334152043 STAINLESS STEEL TRAY WASHER UP TO 300 TRAYS PER HOUR - USED MARCHANT SCHMIDT TRAY WASHER WITH: PRODUCTION SPEED: TRAYS: UP TO 300 PER HOUR PALLETS AND POLY TOTE LIDS: 100 PER HOUR, DEPENDING ON PRODUCT PRODUCT SPECIFICATION: ALUMINUM TRAYS: LENGTH: 23.75 INCHES WIDTH: 47.75 INCHES HEIGHT: 0.75 INCHES PLASTIC PALLET: LENGTH: 39.5 INCHES WIDTH: 47 INCHES HEIGHT: 6 INCHES POLY TOTE LID: LENGTH: 41 INCHES WIDTH: 49 INCHES HEIGHT: 1.5 INCHES PLASTIC CORRUGATED SLIP SHEETS: LENGTH: 40 INCHES WIDTH: 48 INCHES HEIGHT: 1.5 INCHES PRE-WASH CHAMBER: PUMP: 7.5 HP TANK: 100 GALLONS HEATING: NONE AMBIENT WASH CHAMBER: PUMP: 7.5 HP TANK: 100 GALLONS HEATER: 120 KW GAS FIRED HEAT EXCHANGER TEMPERATURE: 120... - 140... F RINSE CHAMBER: MAIN INLET: 0.75 INCHES BSP 140... F @ 30-45 PSI HEATING: 140... F (CUSTOMER SUPPLIED) SANITIZER CHAMBER: MAIN INLET: 0.75 INCHES BSP UP TO 105...F @ 30-45 PSI HEATING: NONE AMBIENT BLOWING SECTION: BLOWER: (2) 10 HP HI-PRESSURE FANS AIR KNIVES: 12 PRCISSION KNIVES TOP MOUNTED FANS STAINLESS STEEL CONSTRUCTION ELECTRICAL: 480 VOLTS, 60 HERTZ, 3 PHASE MARCHANT SCHMIDT · 334152043	🔒 Subscribe
METTLER-TOLEDO	SAFELINE POWERCHEK 250	METTLER-TOLEDO SAFELINE POWERCHEK 250 X-RAY WITH: CONTAMINATION DETECTION: ENSURES PRODUCT SAFETY THROUGH THE DETECTION OF CONTAMINANTS SUCH AS GLASS, METAL, STONE AND HIGH-DENSITY PLASTIC IN BULK PRODUCTS INTUITIVE USER INTERFACE: AUTOMATIC PRODUCT SET-UP CAN BE READILY COMPLETED WITHOUT THE NEED FOR AN ENGINEER ENSURING MAXIMUM UP-TIME AND AN OPPORTUNITY FOR COST SAVINGS HYGENIC DESIGN: EASY ACCESS TO ALL MACHINE AREAS WITH NO HIDDEN BUG TRAPS. POWERCHEK SYSTEMS ARE IP65 STANDARD WITH AN IP69K OPTION FOR HARSH WASH DOWN ENVIRONMENTS FULL COLOR 15 INCH TOUCH SCREEN HMI CURRENT APERTURE DIMENSIONS: 2 INCHES TALL X 3.375 INCHES WIDE. IS CAPABLE OF RUNNING LARGER APERTURE DEPENDENT ON PRODUCT REQUIREMENTS. CONTACT YOUR SALES REPRESENTATIVE FOR ADDITIONAL INFORMATION CONVEYOR DIMENSIONS: 11 INCHES WIDE X 62.5 INCHES PREVIOUSLY RUNNING GRANOLA BARS LEFT-TO-RIGHT PRODUCT FLOW AIR PRODUCT REJECT X-RAY EMISSIONS: < 5 ?SV PER HOUR X-RAY PROTECTION: LINE OF SIGHT, CURTAINS, SHIELDING METTLER-TOLEDO · SAFELINE POWERCHEK 250	🔒 Subscribe
PEERLESS	WPD0628CA	PEERLESS WPD0628CA STAINLESS STEEL 6-SPOT DEPOSITOR WITH PROGRAMMABLE PORTIONING. HOPPER DIMENSIONS: LENGTH:46 INCHES WIDTH: 31 INCHES DEPTH: 19 INCHES. CANTILEVER DESIGN, SITS OVER AN EXISTING CONVEYOR LINE. HEIGHT CLEARANCE: 37 INCHES. DEPOSITOR CENTERS ARE 4.5". PROGRAMMABLE PORTIONING. ALLEN-BRADLEY MICROLOGIX1500 CONTROLS. ALLEN-BRADLEY PANELVIEW 300 MICRO HMI. ELECTRICAL REQUIREMENTS: 115 VOLTS 60 HZ SINGLE PHASE. STAINLESS STEEL CONSTRUCTION ON CASTER WHEELS. CAN DO PARTICULATES BUT THE BATTER HAS TO BE FLOWABLE. PEERLESS · WPD0628CA	🔒 Subscribe
RONDO	SFT 262V.A0	RONDO SFT 262V.A0 STAINLESS STEEL AUTOMATIC DOUGH CUTTING TABLE - USED RONDO CUTTING TABLE WITH: VARIABLE CONVEYOR SPEED: BETWEEN 22 FEET PER MINUTE CONVEYOR DIMENSIONS: LENGTH: APPROXIMATELY 104 INCHES WIDTH: APPROXIMATELY 25.25 INCHES INFEED/DISCHARGE HEIGHT: 31 INCHES DOUGH CLEARANCE HEIGHT: 1 INCH (6) BLADES BLADE DIAMETER: 4 INCHES OVERALL DIMENSIONS: LENGTH: 139.8 INCHES WIDTH: 28.15 INCHES HEIGHT: 36 INCHES STAINLESS STEEL CONSTRUCTION ELECTRICAL: 50/60 HZ, 200-400 VOLTS LAST RAN: CROISSANTS RONDO · SFT 262V.A0	🔒 Subscribe
SOUTHWORTH	SPTU-2	SOUTHWORTH SPTU-2 PORTABLE STRADDLE BIN AND TOTE TILTER - USED SOUTHWORTH STRADDLE TOTE TILTER WITH: CAPACITY: 2000 POUNDS FORK DIMENSIONS: LENGTH: 40 INCHES WIDTH: 6 INCHES LOWERED HEIGHT: 3.5 INCHES DISTANCE BETWEEN FORKS: 12 INCHES MAXIMUM TILT ANGLE: 85 DEGREES PUSH BUTTON CONTROLLER WITH MAGNETIC BACKING FOOT OPERATED FLOOR LOCK OVERALL DIMENSIONS: LENGTH: 51 INCHES WIDTH: 57 INCHES HEIGHT: 36 INCHES ELECTRICAL: 1 PHASE, 60 HZ, 115 VOLTS SOUTHWORTH · SPTU-2	🔒 Subscribe
METTLER TOLEDO	SAFELINE	METTLER TOLEDO SAFELINE CHECK WEIGH AND METAL DETECTOR - USED METTLER TOLEDO CHECK WEIGH AND METAL DETECTOR WITH: PREVIOUS APPLICATION: 6 AND 15 OUNCE CONTAINERS INFEED/DISCHARGE: 32 INCHES HIGH CONVEYOR WIDTH: 2.5 INCHES AFFECTIVE APERTURE: HEIGHT: 10.5 INCHES WIDTH: 7.75 INCHES TOTAL APERTURE: 11.5 INCHES CHECK WEIGH LENGTHS: 5.75 INCHES 7 INCHES 4.5 INCHES 2 PUSH BAR REJECTS, ONE FOR EACH DETECTION TOUCH SCREEN HMI ELECTRICALS: 3 PHASE, 480 VOLTS, 50/60 HERTZ OVERALL DIMENSIONS: LENGTH: 4 FEET WIDTH: 12 FEET HEIGHT: 7.5 FEET STAINLESS STEEL CONSTRUCTION METTLER TOLEDO · SAFELINE	🔒 Subscribe
ROBERTS	C1250 HFFS	ROBERTS C1250 HFFS STAND UP POUCH MACHINE WITH ZIPPER ATTACHMENT: CURRENTLY RUNNING AT 50 BAGS PER MINUTE CURRENT BAG SIZE: 7.87 INCHES WIDE X 10 INCHES TALL ZIPPER UNWIND POUCH OPENER AIR BLAST FRONT EJECT AIR BLAST 12 ROTARY STYLE INFEED BUCKETS (2) OSCILLATING BUCKET DUMPS FILM REGISTRATION FILM ROLL: 37 INCHES WIDE ROBERTS · C1250 HFFS	🔒 Subscribe
HINDS-BOCK	4P-01S	HINDS-BOCK 4P-01S HIGH SPEED STAINLESS STEEL MEAL KIT DEPOSITOR - USED HINDS-BOCK 4P-01S HIGH SPEED MEAL KIT DEPOSITOR WITH: DESIGNED FOR THE HIGH SPEED DEPOSITING OF SAUCE PELLETS FOR MEAL KITS AND FOR THE HIGH SPEED DEPOSITING OF SAUCE, CONDIMENTS AND FILLINGS INTO THERMO FORMED CAVITIES OF HORIZONTAL VACUUM FORMERS OR PRE-MADE CUPS. OUTPUT: UP TO 5700 PORTIONS PER MINUTE, DEPENDING ON VISCOSITY HOPPER DIMENSIONS: 32 INCH DIAMETER X APPROXIMATELY 15 INCHES DEEP PRODUCT HOPPER VOLUME: APPROXIMATELY 50 GALLONS AGITATED HOPPER (2) 3.5 INCH DIAMETER HOPPER INFEEDS (4) SERVO DRIVEN JEC LTD POSITIVE DISPLACEMENT PUMPS FOR MOVING PRODUCT FROM THE HOPPER TO THE DEPOSITING NOZZLES SERVO DRIVEN ORBITAL SPOUT BRIDGE ALLOWS THE NOZZLES TO FOLLOW PRODUCT DOWN THE CONVEYOR BELT STAINLESS STEEL CONSTRUCTION ALLEN-BRADLEY PANELVIEW PLUS 700 HMI HINDS-BOCK · 4P-01S	🔒 Subscribe
KONIG	ARTISAN SFI 350 II M	[KONIG ARTISAN SFI 350 II M] STAINLESS STEEL DOUGH SHEETER - USED KONIG DOUGH SHEETER WITH: THROUGHPUT: UP TO 1,200 KILOGRAMS PER HOUR WITH FIRMER DOUGH UP TO 500 KILOGRAMS PER HOUR WITH SOFTER DOUGH PNEUMATIC AGITATED STAMPERS STAMPER DIMENSIONS: LENGTH: 3 INCHES WIDTH: 3 INCHES DEPTH: 1.5 INCHES TRO 300 STAINLESS STEEL HOPPER HOPPER CAPACITY: 300 KILOGRAMS (650 POUNDS) SIEMENS SIMATIC PANEL TOUCH SCREEN HMI APPROXIMATE OVERALL DIMENSIONS: LENGTH: 60 FEET WIDTH: 4 FEET HEIGHT: 7 FEET STAINLESS STEEL CONSTRUCTION ELECTRICAL: 3 PHASE, 60 HZ, 208 VOLTS, 12 AMPS PREVIOUSLY USED IN BAKERY APPLICATION KONIG · ARTISAN SFI 350 II M	🔒 Subscribe
GRAPHIC PACKAGING	MD15RF2	GRAPHIC PACKAGING MD15RF2 PICK AND PLACE TOPSERTER WITH: APPLICATION: PICKS AND PLACES MEDICAL LITERATURE ONTO CONTAINERS 2 PNEUMATIC PICKING HEADS ROTARY PICKING ACTION DUAL PRODUCT INFEEDS VARIABLE FREQUENCY DRIVE OVER LINE DESIGN GRAPHIC PACKAGING · MD15RF2	🔒 Subscribe

Make	Model	Description	Price
EDL PACKAGING ENGINEERS	MULTIPACKER AND BUNDLER	EDL PACKAGING ENGINEERS NON-REGISTERED UNSUPPORTED MULTIPACKER AND BUNDLER WITH 90-DEGREE INFEED - USED EDL PACKAGING ENGINEERS MULTIPACKER AND BUNDLER WITH: 90... INFEED CONVEYOR WIDTH: 6 INCHES ADJUSTABLE HEIGHT SIDE RAILS FILM WIDTH: 20.125 INCHES HEAT SEAL JAW WIDTH: 26.5 INCHES PUSH ARM WIDTH: 16.25 INCHES HEAT TUNNEL APERTURE: WIDTH: 26.5 INCHES HEIGHT: 16.5 INCHES LEFT-TO-RIGHT OPERATION PLASTIC-TOP DISCHARGE CONVEYOR ELECTRICAL REQUIREMENTS: 277/480 VOLTS 60 HZ 3 PHASE ADJUSTABLE HEIGHT LEVELING LEGS PAINTED STEEL CONSTRUCTION LAST BUNDLING (4) 16-OUNCE AND (4) 32-OUNCE BAGS OF COFFEE	🔒 Subscribe
GROEN	D-60	GROEN D-60 60 GALLON HALF JACKETED STAINLESS STEAM KETTLE - USED GROEN D-60 STEAM KETTLE WITH: CAPACITY: 60 GALLONS DIMENSIONS: DIAMETER: 30 INCHES DEPTH: 25 INCHES HALF JACKETED: 25 PSI AT 300... F HAND CRANK TILT STAINLESS STEEL CONSTRUCTION	🔒 Subscribe
MIDDLEBY MARSHAL	PS360WB	MIDDLEBY MARSHAL PS360WB OVEN - USED MIDDLEBY MARSHAL OVEN WITH: INFEED: LENGTH: 53 INCHES WIDTH: 41 INCHES HEIGHT: 5 INCHES OVEN ACCESS PANEL WITH VIEWING GLASS: LENGTH: 38 INCHES HEIGHT: 5 INCHES PUSH BUTTON CONTROLS DIGITAL TEMPERATURE READOUT ELECTRICAL: 240 VOLTS, 1 PH, 60 HZ REQUIRES BELT	🔒 Subscribe
MIDDLEBY MARSHAL	PS360WB	MIDDLEBY MARSHAL PS360WB OVEN - USED MIDDLEBY MARSHAL OVEN WITH: INFEED: LENGTH: 53 INCHES WIDTH: 41 INCHES HEIGHT: 5 INCHES OVEN ACCESS PANEL WITH VIEWING GLASS: LENGTH: 38 INCHES HEIGHT: 5 INCHES PUSH BUTTON CONTROLS DIGITAL TEMPERATURE READOUT ELECTRICAL: VOLTS: 240 FREQUENCY: 60 HZ PHASE 1 NO BELT	🔒 Subscribe
		64" L X 33" W TRANSFER CONVEYOR - USED TRANSFER CONVEYOR: CONVEYOR DIMENSIONS: LENGTH: 64 INCHES WIDTH: 33 INCHES INFEED HEIGHT: 24 INCHES DISCHARGE HEIGHT: 24 INCHES	🔒 Subscribe
B+ EQUIPMENT (SEALED AIR)	I-PACK BA24B-2	B+ EQUIPMENT (SEALED AIR) I-PACK BA24B-2 GLUE BOTTOM SEAL CASE ERECTOR - USED CASE ERECTOR WITH: MINIMUM CASE DIMENSIONS: LENGTH: 7 INCHES WIDTH: 5.5 INCHES HEIGHT: 0.75 INCHES MAXIMUM CASE DIMENSIONS: LENGTH: 35 INCHES WIDTH: 23.5 INCHES HEIGHT: 23.5 INCHES LAST RUN CASE DIMENSIONS: LENGTH: 10.75 INCHES WIDTH: 6.5 INCHES HEIGHT: 6.5 INCHES MAGAZINE DIMENSIONS: LENGTH: 33 INCHES WIDTH: 12 INCHES PUSH BUTTON CONTROLS ELECTRICAL REQUIREMENTS: 400 VOLTS, 50 HERTZ, 3 PHASE OVERALL DIMENSIONS: LENGTH: 9 FEET WIDTH: 6 FEET HEIGHT: 6 FEET	🔒 Subscribe
REVENT	619 G DG	REVENT 619 G DG 318,000 BTU NATURAL GAS-FIRED DOUBLE RACK OVEN - USED REVENT 619G DG DOUBLE RACK OVEN WITH: CAPACITY: DOUBLE RACK BTU: 318,000 FUEL: NATURAL GAS TIMERS DIGITAL TEMPERATURE READ OUTS DOUBLE PANE VIEWING WINDOW STAINLESS STEEL CONSTRUCTION ELECTRICAL: 208 VOLTS, 60 HZ, 3 PHASE, 15 AMPS	🔒 Subscribe
FORMOST FUJI	FW3400A-5	FORMOST FUJI FW3400A-5 HORIZONTAL FLOW WRAPPER - USED FORMOST FUJI FW3400A-5 FLOW WRAPPER WITH: PRINT REGISTERED HORIZONTAL FLOW WRAPPER INFEED LENGTH: 100 INCHES MANUAL PRODUCT LOAD LUGGED INFEED LUG CENTERS: 14 INCHES FILM WIDTH: 17 INCHES AUTOMATIC FILM SPLICING ROTARY LONGITUDINAL FIN SEAL TOUCH SCREEN HMI LEFT TO RIGHT PRODUCT FLOW STAINLESS STEEL CONTACT PARTS PAINTED, MILD STEEL FRAME LAST USED FOR BAGELS	🔒 Subscribe
MATRIX	PROTEUS 2840SER	[MATRIX PROTEUS 2840ER VERTICAL FORM FILL SEAL] SEAL JAW LENGTH: 12 INCHES MAXIMUM FILM WIDTH: 22 INCHES FORMER: DSL FORMING COLLAR DIAMETER: 2.5 INCHES PILLOW BAGS PRINT REGISTRATION DISCHARGE HEIGHT: 20 INCHES MARKEM SMART DATE 2 DATE CODER ALLEN-BRADLEY PANELVIEW PLUS 1000 TOUCHSCREEN HMI FORMING COLLAR MAKES A LEFT OVER RIGHT FIN SEAL S/N: 75361DSL	🔒 Subscribe
		ROTATING CENTER CIRCULAR TABLE WITH 20 INCH SPIKES - USED TABLE WITH: CIRCULAR DIAMETER: 84 INCHES WORKING HEIGHT: 34 INCHES MANUALLY ROTATING CENTER: DIAMETER: 60 INCHES PLACEMENT SPIKES: LENGTH: 20 INCHES	🔒 Subscribe
VESTIL	TMS-20-DC	VESTIL MANUFACTURING TMS-20-DC TILT MASTER STRADDLE PALLET LIFT - USED VESTIL PALLET JACK WITH: CAPACITY: 2000 POUNDS FORK DIMENSIONS: LENGTH: 35 INCHES WIDTH: 4 INCHES FORK ADJUSTMENT I.D: MINIMUM: 0.5 INCHES MAXIMUM: 28.5 INCHES MAXIMUM TILT: 90 DEGREES LOAD CENTER: 18 INCHES WHEEL TYPE: PHENOLIC ROTATED HEIGHT: 37 INCHES LOWERED HEIGHT: 3 INCHES OVERALL DIMENSIONS: WIDTH: 57.25 INCHES DEPTH: 73.25 INCHES HEIGHT: 29.25 INCHES PAINTED STEEL CONSTRUCTION ELECTRICAL: 12 VOLT DC, 140 FULL LOAD AMPS PREVIOUSLY USED IN POPCORN FACILITY	🔒 Subscribe
		64" L X 33" W TRANSFER CONVEYOR - USED TRANSFER CONVEYOR: CONVEYOR DIMENSIONS: LENGTH: 64 INCHES WIDTH: 33 INCHES INFEED HEIGHT: 17 INCHES DISCHARGE HEIGHT: 17 INCHES	🔒 Subscribe
LAUDENBERG	FBL 22 HFFS	[LAUDENBERG FBL 22 HFFS] ROTARY HORIZONTAL POUCH FORM FILL SEALER WITH ZIPPER - USED LAUDENBERG FBL 22 HFFS POUCH MACHINE WITH: INTERMITTENT, ROTARY HORIZONTAL POUCH FORMING, FILLING, AND SEALING MACHINE FORMS AND FILLS POUCH UPSIDE DOWN, TOP OF THE FINISHED POUCH IS SEALED FIRST POUCH DIMENSIONS: MINIMUM: 4.72 INCHES WIDE X 3.93 INCHES LONG MAXIMUM: 7.4 INCHES WIDE X 13 INCHES LONG CURRENT POUCH SIZE: APPROXIMATELY 6 INCHES WIDE X 11 INCHES LONG CURRENT FILM WIDTH: 22 INCHES OUTPUT: UP TO 200 POUCHES PER MINUTE, DEPENDING ON PRODUCT, FILL METHOD, AND POUCH SIZE RESEALABLE ZIPPER APPLICATOR GAS FLUSH PRINT REGISTRATION POUCH HANGER HOLE PUNCH SERVO MOTOR DRIVEN FOOD GRADE, STAINLESS STEEL CONSTRUCTION	🔒 Subscribe
		64" L X 33" W TRANSFER CONVEYOR - USED TRANSFER CONVEYOR: CONVEYOR DIMENSIONS: LENGTH: 64 INCHES WIDTH: 33 INCHES INFEED HEIGHT: 24 INCHES DISCHARGE HEIGHT: 24 INCHES S/N:	🔒 Subscribe
KEY TECHNOLOGY	ISO-FLO 211	KEY TECHNOLOGY ISO-FLO 211"L X 18"W STAINLESS STEEL VIBRATORY CONVEYOR - USED KEY TECHNOLOGY VIBRATORY CONVEYOR WITH: CONVEYOR DIMENSIONS: LENGTH: 211 INCHES WIDTH: 18 INCHES DISCHARGE HEIGHT: 65.5 INCHES STAINLESS STEEL CONSTRUCTION MOUNTED ON 8 INCH CASTERS ELECTRICAL: 460 VOLTS, 60 HERTZ, 3 PHASE	🔒 Subscribe
STRATASYS	CONNEX 350	[STRATASYS CONNEX 350] 3D PRINTER USES SPECIAL TECHNOLOGY TO PRINT MODELS SIMULTANEOUSLY WITH DIFFERENT MODEL MATERIALS. PRINTING MODELS WITH COMBINATIONS OF BASIC MATERIALS (DIGITAL MATERIALS) ENABLES YOU TO CHOOSE FROM A WIDE RANGE OF MECHANICAL PROPERTIES?FROM FLEXIBLE TO RIGID?AND COLORS. IT IS ALSO CAPABLE OF PRINTING MODELS MADE FROM DIFFERENT MATERIALS ON THE SAME BUILD TRAY IN THE SAME PRINT JOB AND QUICKLY ALTERNATING BETWEEN PRINTING JOBS USING THE MODEL MATERIALS LOADED. USED STRATASYS OBJET 350 3D PRINTER WITH: BUILD AREA DIMENSIONS (INCHES): LENGTH: 13.4 WIDTH: 13.4 HEIGHT: 7.9 RESOLUTION (DOTS PER INCH): X-AXIS: 600 DPI Y-AXIS: 600 DPI Z-AXIS: 1,600 DPI OVERALL DIMENSIONS (INCHES): LENGTH: 55.1 WIDTH: 49.6 HEIGHT: 43.4 MINIMUM LAYER THICKNESS (HORIZONTAL BUILD LAYERS): 16 MICRONS (0.0006 INCH) BUILD MODE RESOLUTIONS: DIGITAL MATERIAL: 30-MICRON (0.001 INCH) HIGH QUALITY: 16-MICRON (0.0006 INCH) HIGH SPEED: 30-MICRON (0.001 INCH) NETWORK CONNECTIVITY: LAN - TCP/IP OPERATING CONDITIONS: 64...F TO 77...F; RELATIVE HUMIDITY 30 TO 70% CE LISTED POWER: 110-240 VAC, 50/60 HZ, 1.5 KW, SINGLE PHASE	🔒 Subscribe
		USED PALLET OF MRO PALLET INCLUDES MRO PARTS FOR BUCKET CHECK WEIGHER DIAMETER OF CLEAR PLASTIC FUNNEL: 16 INCHES OVERALL DIMENSIONS: LENGTH: 40 INCHES WIDTH: 48 INCHES HEIGHT: 33 INCHES	🔒 Subscribe
VULCAN HART	ET88	VULCAN HART ET88 OVEN WITH: ELECTRICAL REQUIREMENTS: 480 VOLTS, 60 HERTZ, 3 PHASE	🔒 Subscribe
PACKRITE	6000-4240-000	[USED] PACKRITE 6000-4240-000 CONTINUOUS BAND BAG SEALER WITH: PRODUCT FLOW: RIGHT TO LEFT SEAL WIDTH: .75 OF AN INCH DIGITAL TEMPERATURE CONTROLS VARIABLE SPEED: UP TO 750 INCHES PER MINUTE TEFLON FABRIC BANDS MAXIMUM TEMPERATURE: 600 DEGREES FAHRENHEIT ADJUSTABLE WORKING HEIGHT	🔒 Subscribe
BOSCH DOBOY	LINIUM 301	BOSCH DOBOY LINIUM 301 PRINT REGISTER FLOW WRAPPER WITH: APPLICATION: DESIGNED TO FLOW WRAP PRODUCTS WITH PRINT REGISTERED FILM OUTPUT: UP TO 150 PACKAGES PER MINUTE PRODUCT SIZE RANGE: MINIMUM (INCHES): 3.5 LONG X 0.4 WIDE MAXIMUM (INCHES): 7.25 LONG X 6.9 WIDE MAXIMUM HEIGHT (WITH PROPER CHANGE PARTS): 2.5 INCHES BOSCH INFEED SERIAL: 05-25838 INFEED LENGTH: 97 INCHES INFEED BELT WIDTH: 5 INCHES LUGGED INFEED LUG CENTER SET: 10 INCHES PRINT REGISTRATION: EYE PACKAGING MATERIALS: PRINTED OR UNPRINTED HEAT SEALABLE POLYPROPYLENES LAMINATES FILM SPECS: MAXIMUM WIDTH: 23.6 INCHES MAXIMUM REEL DIAMETER: 15.7 INCHES ON 3 INCH CORE 1 UP CRIMP VERTICAL SEAL: 9 INCHES WIDE	🔒 Subscribe
RYSON	NT1100-150-B441/4	RYSON NT1100-150-B441/4 DECLINING SPIRAL ELEVATOR CONVEYOR - USED RYSON SPIRAL CONVEYOR WITH: CONVEYOR WIDTH: 6 INCHES WEIGHT CAPACITY: 50 POUNDS PER LINEAR FOOT TOTAL WEIGHT: UP TO 3600 POUNDS SPEED: UP TO 200 FEET PER MINUTE DEPENDING ON PRODUCT AND APPLICATION DISTANCE BETWEEN TIERS: 15.25 INCHES PRODUCT CLEARANCE: 13 INCHES INFEED HEIGHT: 96 INCHES DISCHARGE HEIGHT: 34 INCHES OUTSIDE DIAMETER: 50 INCHES CENTERLINE DIAMETER: 44 INCHES OVERALL DIMENSIONS: DIAMETER: 50 INCHES HEIGHT: APPROXIMATELY 100 INCHES DRIVE MOTOR: 2 HORSEPOWER ELECTRICAL: 3 PHASE, 60 HZ, 230/460 VOLTS PREVIOUSLY USED IN POPCORN FACILITY	🔒 Subscribe
AM MANUFACTURING	ROUND-O-MATIC R-900C	AM MANUFACTURING ROUND-O-MATIC R-900C DOUGH ROUNDER WITH: PRODUCTION RATE: UP TO 72000 PIECES PER HOUR, DEPENDING ON APPLICATION PRODUCTION RANGE: MINIMUM: 1 OUNCE MAXIMUM: 2.5 POUNDS CONVEYOR DIMENSIONS: LENGTH: 18.5 INCHES WIDTH: 12 INCHES HIEGHT UNDER CONVEYOR: 32.75 INCHES STAINLESS STEEL CONSTRUCTION ELECTRICAL REQUIREMENTS: 240 VOLTS, 60 HERTZ, 3 PHASE OVERALL DIMENSIONS: LENGTH: 47 INCHES WIDTH: 24 INCHES HEIGHT: 42.5 INCHES	🔒 Subscribe
ULMA	FLORIDA	[ULMA FLORIDA] HORIZONTAL, AUTOMATIC, 1-UP, PRINT REGISTERED, FLOW WRAPPER - USED ULMA FLORIDA HORIZONTAL FLOW WRAPPER WITH: SPEED: UP TO 150 PACKAGES PER MINUTE DIRECTION OF TRAVEL: LEFT TO RIGHT PRINT REGISTRATION EYE DATA SENSOR TLU-115 FILM WIDTH: 500 MILLIMETERS MANDRIL DIAMETER: 76 MILLIMETERS MAXIMUM REEL DIAMETER: 300 MILLIMETERS MAXIMUM PRODUCT DIMENSIONS: WIDTH: 250 MILLIMETERS 9.84 INCHES HEIGHT: 70 MILLIMETERS 2.75 INCHES MINIMUM PRODUCT DIMENSIONS: WIDTH: 10 MILLIMETERS .39 INCHES HEIGHT: 5 MILLIMETERS .20 INCHES ROTARY CROSS SEALING JAWS SELF CENTERING REEK HOLDER WITH BRAKE SYSTEM 70 INCH LONG PRODUCT INFEED CONVEYOR 1 INCH X 1 INCH PLASTIC LUGS 16 INCH CENTERS DISCHARGE HEIGHT: 30 INCHES ADJUSTABLE FILM FOLDING BOX (3) PAIRS OF ROLLERS FOR LONGITUDINAL FILM PULLING AND SEALING AIR CONSUMPTION: 50 LITERS PER MINUTE AT 6 BAR ELECTRICAL REQUIREMENTS: 220 VOLTS, 60 VOLTS, 3 PHASE	🔒 Subscribe
ISHIDA	CCW-Z-212P-D/08-BP	ISHIDA HEAT AND CONTROL CCW-Z-212P-D/08-BP COMPUTER COMBINATION WEIGHER WITH: 12 WEIGHING HEADS WEIGHING METHOD: PAIR DISCHARGE METHOD: DOUBLE - PRODUCTS DISCHARGE SEPARATELY VIA A 2-TUBE, DOUBLE CHUTE HOPPER VOLUME: 800CC PAINTED BODY WEIGHING CAPACITY: 1000 GRAMS WEIGHING RANGE: 14 TO 1000 GRAMS ACCURACY: < 2.0 GRAMS WEIGHING SPEED: 140 WEIGHS PER MINUTE (70 WEIGHS PER MINUTE, PER SIDE), DEPENDS ON PRODUCT SHAPE, DENSITY, TARGET WEIGHT, ETC 16-BIT MICROPROCESSOR CONTROLLER SMOOTH WEIGH BUCKETS	🔒 Subscribe
INGERSOLL RAND	SSR-EP40SE	INGERSOLL RAND SSR-EP40SE ROTARY SCREW AIR COMPRESSOR - USED INGERSOLL RAND ROTARY SCREW AIR COMPRESSOR WITH: CAPACITY: 163 CFM RATED OPERATING PRESSURE: 125 PSIG MAXIMUM DISCHARGE PRESSURE: 128 PSIG MAXIMUM MODULATE PRESSURE: 128 PSIG NOMINAL DRIVE MOTOR: 40 HORSEPOWER ELECTRICAL REQUIREMENTS: 230/460 VOLTS, 60 HERTZ, 3 PHASE	🔒 Subscribe
YAMATO	4RGB	21 YAMATO 4RGB WEIGH ACTUATOR UNIT, (2) ALLEN BRADLEY CONTROL LOGIX 8 AXIS SERCOS SERVO MODULE. OVERALL DIMENSIONS: LENGTH: 48 INCHES WIDTH: 40 INCHES HEIGHT: 37 INCHES	🔒 Subscribe
MIDDLEBY MARSHAL	PS360WB	MIDDLEBY MARSHAL PS360WB OVEN - USED MIDDLEBY MARSHAL OVEN WITH: INFEED: LENGTH: 53 INCHES WIDTH: 41 INCHES HEIGHT: 5 INCHES OVEN ACCESS PANEL WITH VIEWING GLASS: LENGTH: 38 INCHES HEIGHT: 5 INCHES PUSH BUTTON CONTROLS DIGITAL TEMPERATURE READOUT ELECTRICAL: VOLTS: 240 FREQUENCY: 60 HZ PHASE 1 NO BELT	🔒 Subscribe
PIZZAMATIC	SMOOTH TOP CONVEYOR	PIZZAMATIC SMOOTH TOP CONVEYOR 180 DEGREE 26" W - USED PIZZAMATIC SMOOTH TOP CONVEYOR WITH: CONVEYOR WIDTH: 26 INCHES 180 DEGREE TURN SMOOTH TOP CONVEYOR BELT STAINLESS STEEL CONSTRUCTION VARIABLE FREQUENCY DRIVE WELDED TUBULAR FRAME CASTERS	🔒 Subscribe
FOODTOOLS	CS-4AAC	USED FOODTOOLS CS-4AAC SEMI-AUTO ROUND CAKE PORTIONER WITH: SPEED: UP TO 150 PRODUCTS PER HOUR PRODUCT SIZES: 6 TO 12 INCH DIAMETER UP TO 6.5 INCHES TALL PORTION SIZES: 4 TO 24 PORTIONS PRODUCT TYPE: ROUND PRODUCT TEMPERATURE: FROZEN, CHILLED, HARD STAINLESS STEEL BLADE MANUAL FEED DIVIDER INSERTS AIR REQUIREMENTS: COMPRESSED AIR 5 CFM AT 90 PSI OVERALL DIMENSIONS: 27 INCHES LONG X 21 INCHES WIDE X 54 INCHES TALL	🔒 Subscribe
RHEON	37" WIDE GUILLOTINE CUTTING LINE SYSTEM	RHEON GRAVIMETRIC 37" WIDE GUILLOTINE CUTTING LINE SYSTEM WITH: RHEON GUILLOTINE CUTTER 37" WIDE TIMING CONVEYOR SYSTEM: 18.5" LONG X 39.5" WIDE TOP HOLD DOWN CONVEYOR: 32" LONG X 9.5" WIDE RHEON FORMING CONVEYOR INFEED HEIGHT: 38" INFEED LENGTH: 61" OUTFEED CONVEYOR: 14' LONG X 39" WIDE (2) TWO TOP FLOUR DUSTER BOTTOM PAN FEEDING CONVEYOR: 39" WIDE X 40' LONG WORKING HEIGHT OF BOTTOM PAN FEEDER: 26" RHEON WATER SPRAY SYSTEM RHEON SEEDING CONVEYOR RHEON PANNING CONVEYOR RHEON SEPARATING CONVEYOR TOUCH SCREEN CONTROLLER: GOT200 ELECTRICAL REQUIREMENTS: 220 VOLTS / 3 PHASE / 60 HERTZ APPROXIMATE OVERALL DIMENSIONS: 59' LONG X 6' WIDE X 7' TALL	🔒 Subscribe
		66" L X 36" W TRANSFER CONVEYOR - USED TRANSFER CONVEYOR: CONVEYOR DIMENSIONS: LENGTH: 66 INCHES WIDTH: 36 INCHES INFEED HEIGHT: 24 INCHES DISCHARGE HEIGHT: 24 INCHES MOTOR: 2 HORSEPOWER, 208-230/460 VOLTS, 5.7-5.4/2.7 AMPS, 60 HERTZ, 3 PHASE	🔒 Subscribe
R&R MACHINERY MOVERS	BARREL LIFT	BARREL LIFT	🔒 Subscribe
CROWN	DMT-40	CROWN DMT-40 DIRECT STEAM TILTING KETTLE WITH: CAPACITY: 40 GALLONS STAINLESS STEEL CABINET M.D.M.T. 32 DEGREES FAHRENHEIT AT 35 PSI 316 STAINLESS STEEL LINER 6 INCH ADJUSTABLE HOLD DOWN FEET ONE PIECE COVER 2 INCH TANGENT DRAW OFF VALVE STEAM CONTROL VALVE AND STEAM TRAP SWING DRAIN HOT AND COLD DECK MOUNT FAUCET HYDRAULIC TILT PAN CARRIER	🔒 Subscribe
AMF	K	[AMF] MODEL K STAINLESS STEEL VOLUMETRIC DOUGH DIVIDER HEADS (3) - USED AMF DOUGH DIVIDER HEADS (3) WITH: SPEED: BETWEEN 40 AND 100 CUTS PER MINUTE DEPENDING ON PRODUCT AND APPLICATION CUT CAPACITY: MINIMUM: 0.75 OUNCES MAXIMUM: 4.25 OUNCES PISTON DIAMETER: 2 INCHES NUMBER OF PISTONS: 6 PISTON CENTERS: 4.25 INCHES APPROXIMATE OVERALL DIMENSIONS: WIDTH: 35 INCHES DEPTH: 30 INCHES HEIGHT: 34 INCHES STAINLESS STEEL CONSTRUCTION PREVIOUSLY USED IN BAKERY APPLICATION	🔒 Subscribe
		STAINLESS STEEL 3" W X 70" L TABLE-TOP CONVEYOR - USED STAINLESS STEEL CONVEYOR WITH: CONVEYOR DIMENSIONS: 3 INCHES WIDE X 70 INCHES LONG CONVEYOR HEIGHT: 37 INCHES 1 HORSEPOWER MOTOR STAINLESS STEEL FRAME SCREW DOWN LEVELING FEET	🔒 Subscribe
DONALDSON TORIT	VS 1200 QD	DONALDSON TORIT VS 1200 QD WITH: 6 INCH INLET 1200 CUBIC FEET PER MINUTE 3 HORSEPOWER MOTOR PAINTED STEEL CONSTRUCTION ELECTRICAL REQUIREMENTS: 460 VOLTS, 60 HERTZ, 3 PHASE APPROXIMATE OVERALL DIMENSIONS: LENGTH: 80 INCHES WIDTH: 39 INCHES HEIGHT: 40 INCHES	🔒 Subscribe
CASE	BELT CONVEYOR	2002 CASE BELT CONVEYOR 36" LONG X 6" WIDE WITH GUIDE RAILS - USED CASE BELT CONVEYOR WITH: CONVEYOR DIMENSIONS: 36 INCHES LONG X 6.25 INCHES WIDE PRODUCT GUIDE RAILS	🔒 Subscribe
		USED INDUCTION SEALER WITH FLAT SEALING HEAD: LENGTH: 26 INCHES WIDTH: 5 INCHES HAND CRANK HEIGHT ADJUSTMENT PUSH BUTTON CONTROLS DIGITAL READOUT AIR COOLED ELECTRICAL REQUIREMENTS: 208/240 VOLTS, 60 HERTZ, 1 PHASE MOUNTED ON CASTERS	🔒 Subscribe
DOMINO	A320I	2015 DOMINO A320I STAINLESS STEEL INK JET CODER WITH: MAX NUMBER OF UNICODE CHARACTERS PER LINE: 255 MAX NUMBER OF LINES: 4 MAX NUMBER OF MESSAGES PER STORE: 256 MAX NUMBER OF STORES PER PRINTER: 16 MAX LINE SPEED: 325 METERS PER MINUTE CONDUIT LENGTH: 3 METERS BEND RADIUS: 100 MILLIMETERS TOUCH SCREEN HMI STAINLESS STEEL CONSTRUCTION ELECTRICAL REQUIREMENTS: 240 VOLTS 60 HZ SINGLE PHASE 4 AMPS	🔒 Subscribe
CREMER	TQI-4150	[USED] CREMER TQI-4150 MULTI-CHANNEL COUNTING SYSTEM WITH (3) OSE CLEATED INCLINE CONVEYORS AND Z-FRAME BUCKET ELEVATOR. POUCH BLENDING AND COUNTING SYSTEM, PREVIOUSLY USED TO COUNT AND ASSEMBLE A 6-COUNT VARIETY PACK OF POUCHED SNACKS AND FEED THE POUCHES TO A CARTONER FOR PACKAGING. (3) OSE CLEATED INCLINE CONVEYORS WITH INFEED HEIGHTS OF 50 AND 86.5 INCHES, CONVEYOR WIDTH OF 13.5 INCHES, INFEED LENGTH OF 132 INCHES, CLEAT CENTERS OF 9 INCHES, CLEAT WIDTH OF 12 INCHES, CLEAT HEIGHT OF 3 INCHES, AND DISCHARGE HEIGHT OF 138 INCHES. INCLINE CONVEYORS FEED INTO TQI-4150 COUNTERS. (3) TQI-4150 MULTI-CHANNEL COUNTERS DETERMINE HOW MANY POUCHES GO INTO EACH BATCH, FEATURING A RE-CIRCULATION SYSTEM THAT RETURNS MIS-ALIGNED POUCHES FROM THE COUNTING PROCESS TO THE INFEED INCLINE CONVEYOR. COUNTERS FEED INTO A Z-FRAME BUCKET CONVEYOR WHICH ULTIMATELY DISCHARGES THE BATCHED POUCHES. BUCKET DIMENSIONS: 13.5 INCHES WIDE X 7 INCHES LONG X 6.5 INCHES DEEP. FINAL PRODUCT DISCHARGE HEIGHT: 83 INCHES. PREVIOUSLY USED IN CONJUNCTION WITH A TRIANGLE VCM-E30-1000-90HS0 VERTICAL GLUE CARTONER. OVERALL SYSTEM HEIGHT: 186 INCHES.	🔒 Subscribe
MARCHANT SCHMIDT	334152043	MARCHANT SCHMIDT 334152043 STAINLESS STEEL TRAY WASHER UP TO 300 TRAYS PER HOUR - USED MARCHANT SCHMIDT TRAY WASHER WITH: PRODUCTION SPEED: TRAYS: UP TO 300 PER HOUR PALLETS AND POLY TOTE LIDS: 100 PER HOUR, DEPENDING ON PRODUCT PRODUCT SPECIFICATION: ALUMINUM TRAYS: LENGTH: 23.75 INCHES WIDTH: 47.75 INCHES HEIGHT: 0.75 INCHES PLASTIC PALLET: LENGTH: 39.5 INCHES WIDTH: 47 INCHES HEIGHT: 6 INCHES POLY TOTE LID: LENGTH: 41 INCHES WIDTH: 49 INCHES HEIGHT: 1.5 INCHES PLASTIC CORRUGATED SLIP SHEETS: LENGTH: 40 INCHES WIDTH: 48 INCHES HEIGHT: 1.5 INCHES PRE-WASH CHAMBER: PUMP: 7.5 HP TANK: 100 GALLONS HEATING: NONE AMBIENT WASH CHAMBER: PUMP: 7.5 HP TANK: 100 GALLONS HEATER: 120 KW GAS FIRED HEAT EXCHANGER TEMPERATURE: 120... - 140... F RINSE CHAMBER: MAIN INLET: 0.75 INCHES BSP 140... F @ 30-45 PSI HEATING: 140... F (CUSTOMER SUPPLIED) SANITIZER CHAMBER: MAIN INLET: 0.75 INCHES BSP UP TO 105...F @ 30-45 PSI HEATING: NONE AMBIENT BLOWING SECTION: BLOWER: (2) 10 HP HI-PRESSURE FANS AIR KNIVES: 12 PRCISSION KNIVES TOP MOUNTED FANS STAINLESS STEEL CONSTRUCTION ELECTRICAL: 480 VOLTS, 60 HERTZ, 3 PHASE	🔒 Subscribe
METTLER-TOLEDO	SAFELINE POWERCHEK 250	METTLER-TOLEDO SAFELINE POWERCHEK 250 X-RAY WITH: CONTAMINATION DETECTION: ENSURES PRODUCT SAFETY THROUGH THE DETECTION OF CONTAMINANTS SUCH AS GLASS, METAL, STONE AND HIGH-DENSITY PLASTIC IN BULK PRODUCTS INTUITIVE USER INTERFACE: AUTOMATIC PRODUCT SET-UP CAN BE READILY COMPLETED WITHOUT THE NEED FOR AN ENGINEER ENSURING MAXIMUM UP-TIME AND AN OPPORTUNITY FOR COST SAVINGS HYGENIC DESIGN: EASY ACCESS TO ALL MACHINE AREAS WITH NO HIDDEN BUG TRAPS. POWERCHEK SYSTEMS ARE IP65 STANDARD WITH AN IP69K OPTION FOR HARSH WASH DOWN ENVIRONMENTS FULL COLOR 15 INCH TOUCH SCREEN HMI CURRENT APERTURE DIMENSIONS: 2 INCHES TALL X 3.375 INCHES WIDE. IS CAPABLE OF RUNNING LARGER APERTURE DEPENDENT ON PRODUCT REQUIREMENTS. CONTACT YOUR SALES REPRESENTATIVE FOR ADDITIONAL INFORMATION CONVEYOR DIMENSIONS: 11 INCHES WIDE X 62.5 INCHES PREVIOUSLY RUNNING GRANOLA BARS LEFT-TO-RIGHT PRODUCT FLOW AIR PRODUCT REJECT X-RAY EMISSIONS: < 5 ?SV PER HOUR X-RAY PROTECTION: LINE OF SIGHT, CURTAINS, SHIELDING	🔒 Subscribe
PEERLESS	WPD0628CA	PEERLESS WPD0628CA STAINLESS STEEL 6-SPOT DEPOSITOR WITH PROGRAMMABLE PORTIONING. HOPPER DIMENSIONS: LENGTH:46 INCHES WIDTH: 31 INCHES DEPTH: 19 INCHES. CANTILEVER DESIGN, SITS OVER AN EXISTING CONVEYOR LINE. HEIGHT CLEARANCE: 37 INCHES. DEPOSITOR CENTERS ARE 4.5". PROGRAMMABLE PORTIONING. ALLEN-BRADLEY MICROLOGIX1500 CONTROLS. ALLEN-BRADLEY PANELVIEW 300 MICRO HMI. ELECTRICAL REQUIREMENTS: 115 VOLTS 60 HZ SINGLE PHASE. STAINLESS STEEL CONSTRUCTION ON CASTER WHEELS. CAN DO PARTICULATES BUT THE BATTER HAS TO BE FLOWABLE.	🔒 Subscribe
RONDO	SFT 262V.A0	RONDO SFT 262V.A0 STAINLESS STEEL AUTOMATIC DOUGH CUTTING TABLE - USED RONDO CUTTING TABLE WITH: VARIABLE CONVEYOR SPEED: BETWEEN 22 FEET PER MINUTE CONVEYOR DIMENSIONS: LENGTH: APPROXIMATELY 104 INCHES WIDTH: APPROXIMATELY 25.25 INCHES INFEED/DISCHARGE HEIGHT: 31 INCHES DOUGH CLEARANCE HEIGHT: 1 INCH (6) BLADES BLADE DIAMETER: 4 INCHES OVERALL DIMENSIONS: LENGTH: 139.8 INCHES WIDTH: 28.15 INCHES HEIGHT: 36 INCHES STAINLESS STEEL CONSTRUCTION ELECTRICAL: 50/60 HZ, 200-400 VOLTS LAST RAN: CROISSANTS	🔒 Subscribe
SOUTHWORTH	SPTU-2	SOUTHWORTH SPTU-2 PORTABLE STRADDLE BIN AND TOTE TILTER - USED SOUTHWORTH STRADDLE TOTE TILTER WITH: CAPACITY: 2000 POUNDS FORK DIMENSIONS: LENGTH: 40 INCHES WIDTH: 6 INCHES LOWERED HEIGHT: 3.5 INCHES DISTANCE BETWEEN FORKS: 12 INCHES MAXIMUM TILT ANGLE: 85 DEGREES PUSH BUTTON CONTROLLER WITH MAGNETIC BACKING FOOT OPERATED FLOOR LOCK OVERALL DIMENSIONS: LENGTH: 51 INCHES WIDTH: 57 INCHES HEIGHT: 36 INCHES ELECTRICAL: 1 PHASE, 60 HZ, 115 VOLTS	🔒 Subscribe
METTLER TOLEDO	SAFELINE	METTLER TOLEDO SAFELINE CHECK WEIGH AND METAL DETECTOR - USED METTLER TOLEDO CHECK WEIGH AND METAL DETECTOR WITH: PREVIOUS APPLICATION: 6 AND 15 OUNCE CONTAINERS INFEED/DISCHARGE: 32 INCHES HIGH CONVEYOR WIDTH: 2.5 INCHES AFFECTIVE APERTURE: HEIGHT: 10.5 INCHES WIDTH: 7.75 INCHES TOTAL APERTURE: 11.5 INCHES CHECK WEIGH LENGTHS: 5.75 INCHES 7 INCHES 4.5 INCHES 2 PUSH BAR REJECTS, ONE FOR EACH DETECTION TOUCH SCREEN HMI ELECTRICALS: 3 PHASE, 480 VOLTS, 50/60 HERTZ OVERALL DIMENSIONS: LENGTH: 4 FEET WIDTH: 12 FEET HEIGHT: 7.5 FEET STAINLESS STEEL CONSTRUCTION	🔒 Subscribe
ROBERTS	C1250 HFFS	ROBERTS C1250 HFFS STAND UP POUCH MACHINE WITH ZIPPER ATTACHMENT: CURRENTLY RUNNING AT 50 BAGS PER MINUTE CURRENT BAG SIZE: 7.87 INCHES WIDE X 10 INCHES TALL ZIPPER UNWIND POUCH OPENER AIR BLAST FRONT EJECT AIR BLAST 12 ROTARY STYLE INFEED BUCKETS (2) OSCILLATING BUCKET DUMPS FILM REGISTRATION FILM ROLL: 37 INCHES WIDE	🔒 Subscribe
HINDS-BOCK	4P-01S	HINDS-BOCK 4P-01S HIGH SPEED STAINLESS STEEL MEAL KIT DEPOSITOR - USED HINDS-BOCK 4P-01S HIGH SPEED MEAL KIT DEPOSITOR WITH: DESIGNED FOR THE HIGH SPEED DEPOSITING OF SAUCE PELLETS FOR MEAL KITS AND FOR THE HIGH SPEED DEPOSITING OF SAUCE, CONDIMENTS AND FILLINGS INTO THERMO FORMED CAVITIES OF HORIZONTAL VACUUM FORMERS OR PRE-MADE CUPS. OUTPUT: UP TO 5700 PORTIONS PER MINUTE, DEPENDING ON VISCOSITY HOPPER DIMENSIONS: 32 INCH DIAMETER X APPROXIMATELY 15 INCHES DEEP PRODUCT HOPPER VOLUME: APPROXIMATELY 50 GALLONS AGITATED HOPPER (2) 3.5 INCH DIAMETER HOPPER INFEEDS (4) SERVO DRIVEN JEC LTD POSITIVE DISPLACEMENT PUMPS FOR MOVING PRODUCT FROM THE HOPPER TO THE DEPOSITING NOZZLES SERVO DRIVEN ORBITAL SPOUT BRIDGE ALLOWS THE NOZZLES TO FOLLOW PRODUCT DOWN THE CONVEYOR BELT STAINLESS STEEL CONSTRUCTION ALLEN-BRADLEY PANELVIEW PLUS 700 HMI	🔒 Subscribe
KONIG	ARTISAN SFI 350 II M	[KONIG ARTISAN SFI 350 II M] STAINLESS STEEL DOUGH SHEETER - USED KONIG DOUGH SHEETER WITH: THROUGHPUT: UP TO 1,200 KILOGRAMS PER HOUR WITH FIRMER DOUGH UP TO 500 KILOGRAMS PER HOUR WITH SOFTER DOUGH PNEUMATIC AGITATED STAMPERS STAMPER DIMENSIONS: LENGTH: 3 INCHES WIDTH: 3 INCHES DEPTH: 1.5 INCHES TRO 300 STAINLESS STEEL HOPPER HOPPER CAPACITY: 300 KILOGRAMS (650 POUNDS) SIEMENS SIMATIC PANEL TOUCH SCREEN HMI APPROXIMATE OVERALL DIMENSIONS: LENGTH: 60 FEET WIDTH: 4 FEET HEIGHT: 7 FEET STAINLESS STEEL CONSTRUCTION ELECTRICAL: 3 PHASE, 60 HZ, 208 VOLTS, 12 AMPS PREVIOUSLY USED IN BAKERY APPLICATION	🔒 Subscribe
GRAPHIC PACKAGING	MD15RF2	GRAPHIC PACKAGING MD15RF2 PICK AND PLACE TOPSERTER WITH: APPLICATION: PICKS AND PLACES MEDICAL LITERATURE ONTO CONTAINERS 2 PNEUMATIC PICKING HEADS ROTARY PICKING ACTION DUAL PRODUCT INFEEDS VARIABLE FREQUENCY DRIVE OVER LINE DESIGN	🔒 Subscribe

EDL PACKAGING ENGINEERS MULTIPACKER AND BUNDLER

PACKAGING EQUIPMENT

EDL PACKAGING ENGINEERS NON-REGISTERED UNSUPPORTED MULTIPACKER AND BUNDLER WITH 90-DEGREE INFEED - U...

Hammer Price: 🔒

GROEN D-60

FOOD PROCESSING AND RESTAURANT EQUIPMENT

GROEN D-60 60 GALLON HALF JACKETED STAINLESS STEAM KETTLE - USED GROEN D-60 STEAM KETTLE WITH: CAPAC...

Hammer Price: 🔒

MIDDLEBY MARSHAL PS360WB

FOOD PROCESSING AND RESTAURANT EQUIPMENT

MIDDLEBY MARSHAL PS360WB OVEN - USED MIDDLEBY MARSHAL OVEN WITH: INFEED: LENGTH: 53 INCHES WIDTH: 41...

Hammer Price: 🔒

MIDDLEBY MARSHAL PS360WB

FOOD PROCESSING AND RESTAURANT EQUIPMENT

MIDDLEBY MARSHAL PS360WB OVEN - USED MIDDLEBY MARSHAL OVEN WITH: INFEED: LENGTH: 53 INCHES WIDTH: 41...

Hammer Price: 🔒

MATERIAL HANDLING & WAREHOUSE EQUIPMENT

64" L X 33" W TRANSFER CONVEYOR - USED TRANSFER CONVEYOR: CONVEYOR DIMENSIONS: LENGTH: 64 INCHES WID...

Hammer Price: 🔒

B+ EQUIPMENT (SEALED AIR) I-PACK BA24B-2

PACKAGING EQUIPMENT

B+ EQUIPMENT (SEALED AIR) I-PACK BA24B-2 GLUE BOTTOM SEAL CASE ERECTOR - USED CASE ERECTOR WITH: MIN...

Hammer Price: 🔒

REVENT 619 G DG

FOOD PROCESSING AND RESTAURANT EQUIPMENT

REVENT 619 G DG 318,000 BTU NATURAL GAS-FIRED DOUBLE RACK OVEN - USED REVENT 619G DG DOUBLE RACK OVE...

Hammer Price: 🔒

FORMOST FUJI FW3400A-5

PACKAGING EQUIPMENT

FORMOST FUJI FW3400A-5 HORIZONTAL FLOW WRAPPER - USED FORMOST FUJI FW3400A-5 FLOW WRAPPER WITH: PRIN...

Hammer Price: 🔒

MATRIX PROTEUS 2840SER

PACKAGING EQUIPMENT

[MATRIX PROTEUS 2840ER VERTICAL FORM FILL SEAL] SEAL JAW LENGTH: 12 INCHES MAXIMUM FILM WIDTH: 22 IN...

Hammer Price: 🔒

METALWORKING & FABRICATION EQUIPMENT

ROTATING CENTER CIRCULAR TABLE WITH 20 INCH SPIKES - USED TABLE WITH: CIRCULAR DIAMETER: 84 INCHES W...

Hammer Price: 🔒

VESTIL TMS-20-DC

MATERIAL HANDLING & WAREHOUSE EQUIPMENT

VESTIL MANUFACTURING TMS-20-DC TILT MASTER STRADDLE PALLET LIFT - USED VESTIL PALLET JACK WITH: CAPA...

Hammer Price: 🔒

MATERIAL HANDLING & WAREHOUSE EQUIPMENT

64" L X 33" W TRANSFER CONVEYOR - USED TRANSFER CONVEYOR: CONVEYOR DIMENSIONS: LENGTH: 64 INCHES WID...

Hammer Price: 🔒

LAUDENBERG FBL 22 HFFS

PACKAGING EQUIPMENT

[LAUDENBERG FBL 22 HFFS] ROTARY HORIZONTAL POUCH FORM FILL SEALER WITH ZIPPER - USED LAUDENBERG FBL ...

Hammer Price: 🔒

MATERIAL HANDLING & WAREHOUSE EQUIPMENT

64" L X 33" W TRANSFER CONVEYOR - USED TRANSFER CONVEYOR: CONVEYOR DIMENSIONS: LENGTH: 64 INCHES WID...

Hammer Price: 🔒

KEY TECHNOLOGY ISO-FLO 211

MATERIAL HANDLING & WAREHOUSE EQUIPMENT

KEY TECHNOLOGY ISO-FLO 211"L X 18"W STAINLESS STEEL VIBRATORY CONVEYOR - USED KEY TECHNOLOGY VIBRATO...

Hammer Price: 🔒

STRATASYS CONNEX 350

MISC

[STRATASYS CONNEX 350] 3D PRINTER USES SPECIAL TECHNOLOGY TO PRINT MODELS SIMULTANEOUSLY WITH DIFFER...

Hammer Price: 🔒

MATERIAL HANDLING & WAREHOUSE EQUIPMENT

USED PALLET OF MRO PALLET INCLUDES MRO PARTS FOR BUCKET CHECK WEIGHER DIAMETER OF CLEAR PLASTIC FUNN...

Hammer Price: 🔒

VULCAN HART ET88

FOOD PROCESSING AND RESTAURANT EQUIPMENT

VULCAN HART ET88 OVEN WITH: ELECTRICAL REQUIREMENTS: 480 VOLTS, 60 HERTZ, 3 PHASE...

Hammer Price: 🔒

PACKRITE 6000-4240-000

PACKAGING EQUIPMENT

[USED] PACKRITE 6000-4240-000 CONTINUOUS BAND BAG SEALER WITH: PRODUCT FLOW: RIGHT TO LEFT SEAL WIDT...

Hammer Price: 🔒

BOSCH DOBOY LINIUM 301

PACKAGING EQUIPMENT

BOSCH DOBOY LINIUM 301 PRINT REGISTER FLOW WRAPPER WITH: APPLICATION: DESIGNED TO FLOW WRAP PRODUCTS...

Hammer Price: 🔒

RYSON NT1100-150-B441/4

PACKAGING EQUIPMENT

RYSON NT1100-150-B441/4 DECLINING SPIRAL ELEVATOR CONVEYOR - USED RYSON SPIRAL CONVEYOR WITH: CONVEY...

Hammer Price: 🔒

AM MANUFACTURING ROUND-O-MATIC R-900C

FOOD PROCESSING AND RESTAURANT EQUIPMENT

AM MANUFACTURING ROUND-O-MATIC R-900C DOUGH ROUNDER WITH: PRODUCTION RATE: UP TO 72000 PIECES PER HO...

Hammer Price: 🔒

ULMA FLORIDA

PACKAGING EQUIPMENT

[ULMA FLORIDA] HORIZONTAL, AUTOMATIC, 1-UP, PRINT REGISTERED, FLOW WRAPPER - USED ULMA FLORIDA HORIZ...

Hammer Price: 🔒

ISHIDA CCW-Z-212P-D/08-BP

PACKAGING EQUIPMENT

ISHIDA HEAT AND CONTROL CCW-Z-212P-D/08-BP COMPUTER COMBINATION WEIGHER WITH: 12 WEIGHING HEADS WEIG...

Hammer Price: 🔒

INGERSOLL RAND SSR-EP40SE

AIR COMPRESSORS

INGERSOLL RAND SSR-EP40SE ROTARY SCREW AIR COMPRESSOR - USED INGERSOLL RAND ROTARY SCREW AIR COMPRES...

Hammer Price: 🔒

YAMATO 4RGB

MATERIAL HANDLING & WAREHOUSE EQUIPMENT

21 YAMATO 4RGB WEIGH ACTUATOR UNIT, (2) ALLEN BRADLEY CONTROL LOGIX 8 AXIS SERCOS SERVO MODULE. OVER...

Hammer Price: 🔒

MIDDLEBY MARSHAL PS360WB

FOOD PROCESSING AND RESTAURANT EQUIPMENT

MIDDLEBY MARSHAL PS360WB OVEN - USED MIDDLEBY MARSHAL OVEN WITH: INFEED: LENGTH: 53 INCHES WIDTH: 41...

Hammer Price: 🔒

PIZZAMATIC SMOOTH TOP CONVEYOR

FOOD PROCESSING AND RESTAURANT EQUIPMENT

PIZZAMATIC SMOOTH TOP CONVEYOR 180 DEGREE 26" W - USED PIZZAMATIC SMOOTH TOP CONVEYOR WITH: CONVEYOR...

Hammer Price: 🔒

FOODTOOLS CS-4AAC

FOOD PROCESSING AND RESTAURANT EQUIPMENT

USED FOODTOOLS CS-4AAC SEMI-AUTO ROUND CAKE PORTIONER WITH: SPEED: UP TO 150 PRODUCTS PER HOUR PRODU...

Hammer Price: 🔒

RHEON 37" WIDE GUILLOTINE CUTTING LINE SYSTEM

FOOD PROCESSING AND RESTAURANT EQUIPMENT

RHEON GRAVIMETRIC 37" WIDE GUILLOTINE CUTTING LINE SYSTEM WITH: RHEON GUILLOTINE CUTTER 37" WIDE TIM...

Hammer Price: 🔒

MATERIAL HANDLING & WAREHOUSE EQUIPMENT

66" L X 36" W TRANSFER CONVEYOR - USED TRANSFER CONVEYOR: CONVEYOR DIMENSIONS: LENGTH: 66 INCHES WID...

Hammer Price: 🔒

R&R MACHINERY MOVERS BARREL LIFT

MATERIAL HANDLING & WAREHOUSE EQUIPMENT

BARREL LIFT...

Hammer Price: 🔒

CROWN DMT-40

FOOD PROCESSING AND RESTAURANT EQUIPMENT

CROWN DMT-40 DIRECT STEAM TILTING KETTLE WITH: CAPACITY: 40 GALLONS STAINLESS STEEL CABINET M.D.M.T....

Hammer Price: 🔒

AMF K

FOOD PROCESSING AND RESTAURANT EQUIPMENT

[AMF] MODEL K STAINLESS STEEL VOLUMETRIC DOUGH DIVIDER HEADS (3) - USED AMF DOUGH DIVIDER HEADS (3) ...

Hammer Price: 🔒

MATERIAL HANDLING & WAREHOUSE EQUIPMENT

STAINLESS STEEL 3" W X 70" L TABLE-TOP CONVEYOR - USED STAINLESS STEEL CONVEYOR WITH: CONVEYOR DIMEN...

Hammer Price: 🔒

DONALDSON TORIT VS 1200 QD

DUST COLLECTION EQUIPMENT

DONALDSON TORIT VS 1200 QD WITH: 6 INCH INLET 1200 CUBIC FEET PER MINUTE 3 HORSEPOWER MOTOR PAINTED ...

Hammer Price: 🔒

CASE BELT CONVEYOR

MATERIAL HANDLING & WAREHOUSE EQUIPMENT

2002 CASE BELT CONVEYOR 36" LONG X 6" WIDE WITH GUIDE RAILS - USED CASE BELT CONVEYOR WITH: CONVEYOR...

Hammer Price: 🔒

PACKAGING EQUIPMENT

USED INDUCTION SEALER WITH FLAT SEALING HEAD: LENGTH: 26 INCHES WIDTH: 5 INCHES HAND CRANK HEIGHT AD...

Hammer Price: 🔒

DOMINO A320I

COMMERCIAL PRINTING & BINDERY EQUIPMENT

2015 DOMINO A320I STAINLESS STEEL INK JET CODER WITH: MAX NUMBER OF UNICODE CHARACTERS PER LINE: 255...

Hammer Price: 🔒

CREMER TQI-4150

PACKAGING EQUIPMENT

[USED] CREMER TQI-4150 MULTI-CHANNEL COUNTING SYSTEM WITH (3) OSE CLEATED INCLINE CONVEYORS AND Z-FR...

Hammer Price: 🔒

MARCHANT SCHMIDT 334152043

MISC

MARCHANT SCHMIDT 334152043 STAINLESS STEEL TRAY WASHER UP TO 300 TRAYS PER HOUR - USED MARCHANT SCH...

Hammer Price: 🔒

METTLER-TOLEDO SAFELINE POWERCHEK 250

PACKAGING EQUIPMENT

METTLER-TOLEDO SAFELINE POWERCHEK 250 X-RAY WITH: CONTAMINATION DETECTION: ENSURES PRODUCT SAFETY TH...

Hammer Price: 🔒

PEERLESS WPD0628CA

PACKAGING EQUIPMENT

PEERLESS WPD0628CA STAINLESS STEEL 6-SPOT DEPOSITOR WITH PROGRAMMABLE PORTIONING. HOPPER DIMENSIONS:...

Hammer Price: 🔒

RONDO SFT 262V.A0

FOOD PROCESSING AND RESTAURANT EQUIPMENT

RONDO SFT 262V.A0 STAINLESS STEEL AUTOMATIC DOUGH CUTTING TABLE - USED RONDO CUTTING TABLE WITH: VAR...

Hammer Price: 🔒

SOUTHWORTH SPTU-2

MATERIAL HANDLING & WAREHOUSE EQUIPMENT

SOUTHWORTH SPTU-2 PORTABLE STRADDLE BIN AND TOTE TILTER - USED SOUTHWORTH STRADDLE TOTE TILTER WITH:...

Hammer Price: 🔒

METTLER TOLEDO SAFELINE

PACKAGING EQUIPMENT

METTLER TOLEDO SAFELINE CHECK WEIGH AND METAL DETECTOR - USED METTLER TOLEDO CHECK WEIGH AND METAL D...

Hammer Price: 🔒

ROBERTS C1250 HFFS

PACKAGING EQUIPMENT

ROBERTS C1250 HFFS STAND UP POUCH MACHINE WITH ZIPPER ATTACHMENT: CURRENTLY RUNNING AT 50 BAGS PER M...

Hammer Price: 🔒

HINDS-BOCK 4P-01S

FOOD PROCESSING AND RESTAURANT EQUIPMENT

HINDS-BOCK 4P-01S HIGH SPEED STAINLESS STEEL MEAL KIT DEPOSITOR - USED HINDS-BOCK 4P-01S HIGH SPEED ...

Hammer Price: 🔒

KONIG ARTISAN SFI 350 II M

FOOD PROCESSING AND RESTAURANT EQUIPMENT

[KONIG ARTISAN SFI 350 II M] STAINLESS STEEL DOUGH SHEETER - USED KONIG DOUGH SHEETER WITH: THROUGHP...

Hammer Price: 🔒

GRAPHIC PACKAGING MD15RF2

PACKAGING EQUIPMENT

GRAPHIC PACKAGING MD15RF2 PICK AND PLACE TOPSERTER WITH: APPLICATION: PICKS AND PLACES MEDICAL LITER...

Hammer Price: 🔒

<< Previous 3 4 5 6 7 Next >>

Disclaimer: BidSeek aggregates publicly available auction and liquidation results from independent third-party sources for research and valuation reference only. BidSeek is not affiliated with, endorsed by, sponsored by, or operated in connection with any auction house, marketplace, or liquidation firm. All data and images are provided as-is for informational purposes and remain the property of their respective owners.

Recent Searches

Login

Reset Password

Bakery Processing and Packaging Equipment Auction

Save to Project Folder

Print Options

Save to Project Folder