No Reserve Packaging Processing Equipment Inventory Cleanout Auction

CRETORS FTHC-C15104-1 STAINLESS STEEL BLUE BELT INCLINE CONVEYOR 14"W. CONVEYOR DIMENSIONS: INCLINE LENGTH: 264 INCHES STRAIGHT LENGTH: 48 INCHES CONVEYOR WIDTH: 14 INCHES INFEED HEIGHT: 21 INCHES DISCHARGE HEIGHT: CONVEYOR: 48 INCHES DISCHARGE PAN: 40 INCHES RETRACTABLE DISCHARGE PAN: 6 INCHES INFEED HOPPER DIMENSIONS: WIDTH: 28 INCHES DEPTH: 14 INCHES SANITARY BLUE BELT MOTOR: 0.75 HP ELECTRICALS: 460 VOLTS, 3 PHASE, 60 HERTZ, 1.6 AMPS MOUNTED ON CASTERS STAINLESS STEEL CONSTRUCTION

SHANKLIN OMNI-SLRS HOT KNIFE SIDE SEALER W/ TIMING CONVEYOR INFEED. STYLE: SIDE SEAL HOT KNIFE. PRODUCTION SPEED: UP TO 100 PPM, DEPENDING ON APPLICATION. FILM SPEED: 120 FEET PER MINUTE. MAX PACKAGE SIZE: INFINITE LENGTH X 19 WIDTH X 10 HEIGHT (INCHES). MINIMUM PACKAGE SIZE: 3 LENGTH X 0.5 WIDTH X 0.166 HEIGHT (INCHES). MAX FILM WIDTH FOLDED: 30 INCHES. FLAT: 60 INCHES. SEAL BAR WIDTH: 23 INCHES. INFEED CONVEYOR DIMENSIONS: 37 LENGTH (APPOXIMATELY) X 16 WIDTH X 40 HEIGHT (INCHES). PHOTO EYE TIMED INFEED. FILM PERFORATOR. E-STOP. AIR REQUIREMENTS: 0.5 CUBIC FEET PER MINUTE @ 65 PSIG. ELECTRICAL: 3 PHASE, 50/60 HERTZ, 230 VOLTS.

CRETORS FTHC-C15104-1 STAINLESS STEEL BLUE BELT INCLINE CONVEYOR 14"W. CONVEYOR DIMENSIONS: INCLINE LENGTH: 264 INCHES STRAIGHT LENGTH: 48 INCHES CONVEYOR WIDTH: 14 INCHES INFEED HEIGHT: 21 INCHES DISCHARGE HEIGHT: CONVEYOR: 48 INCHES DISCHARGE PAN: 40 INCHES RETRACTABLE DISCHARGE PAN: 6 INCHES INFEED HOPPER DIMENSIONS: WIDTH: 28 INCHES DEPTH: 14 INCHES SANITARY BLUE BELT MOTOR: 0.75 HP ELECTRICALS: 460 VOLTS, 3 PHASE, 60 HERTZ, 1.6 AMPS MOUNTED ON CASTERS STAINLESS STEEL CONSTRUCTION

MOKON AS4J10JU STAINLESS STEEL WATER CHILLER - USED MOKON WATER CHILLER WITH: MAXIMUM FLUID TEMPERATURE: 65F REFRIGERANT: R-407C COMPRESSOR MOTOR: 10 HORSEPOWER OVERALL DIMENSIONS: LENGTH: 37.5 INCHES WIDTH: 48 INCHES HEIGHT: 80 INCHES ELECTRICAL: 460 VOLTS, 60 HZ, PHASE 3

MTC LEC HYDRAULIC TOTE DUMPER - USED MTC LEC HYDRAULIC TOTE LIFT WITH: CAPACITY: 4000 POUNDS TOTE CHAMBER DIMENSIONS: LENGTH: 46 INCHES WIDTH: 48 INCHES HEIGHT: 63 INCHES INFEED FROM THE GROUND: 15 INCHES APPROXIMATELY STAINLESS STEEL CONSTRUCTION HYDRAULIC PACK INCLUDED DISCHARGE HEIGHT: 44 INCHES MODEL: LEC

TWO HEAD LIQUID FILLER - USED PISTON FILLER WITH: CONVEYOR DIMENSIONS: LENGTH: 60 INCH WIDTH: 4 INCH OVERALL HEIGHT: 32 INCH (ADJUSTABLE) (2) STAINLESS STEEL FILLING HEADS INCLUDES STAINLESS STEEL HOLDING TANK ELECTRICAL: 230 VOLTS 60 HERTZ

GONGDA DRYING, FILLING, CAPPING, AND LABELING LINE - USED GONGDA BEVERAGE LINE WITH: FILLER/CAPPER: 16 HEAD INFEED HEIGHT: 43.5 INCHES DISCHARGE HEIGHT: 42.5 INCHES RUNS LEFT TO RIGHT CURRENT BOTTLE SIZE CONFIGURATION: 12 OUNCES 24 OUNCES BOTTLE MATERIAL: PRESSURIZED GLASS CAP DIAMETER: 13 MM ADJUSTABLE HEIGHT FEET OVERALL DIMENSIONS: LENGTH: 90 INCHES WIDTH: 73 INCHES HEIGHT: 86 INCHES LABELER: VARIABLE SPEED ADJUSTABLE RAILS INFEED HEIGHT: 44 INCHES DISCHARGE HEIGHT: 44 INCHES AUGER SCREW PITCH: 3 INCHES RUNS LEFT TO RIGHT FILM CORE DIAMETER: 2 INCHES TOUCHSCREEN CONTROLS STAINLESS STEEL CONSTRUCTION OVERALL DIMENSIONS: LENGTH: 140 INCHES WIDTH: 33 INCHES HEIGHT: 67 INCHES ADJUSTABLE HEIGHT FEET PACK OFF TABLE INFEED HEIGHT: 41 INCHES RAIL HEIGHT: 3 INCHES OVERALL DIMENSIONS: LENGTH: 40 INCHES WIDTH: 24 INCHES HEIGHT: 45.5 INCHES

HIGHLAND EQUIPMENT STAINLESS STEEL MIXING KETTLE WITH CONTROL BOX - USED JACKETED STAINLESS STEEL TANK WITH: CAPACITY: ~172.2 GALLONS TANK DIAMETER: 37 INCHES MAX. PRESSURE: JACKET DESIGN: 55 PSIG @ 300F TEST PRESSURE: 94 PSIG HEATING METHOD: NATURAL GAS OVERALL DIMENSIONS: LENGTH: 40 WIDTH: 63 HEIGHT: 88 TWO TOP INLETS 1 PRODUCT INLET OUTSIDE DIAMETER: 4 INCHES INSIDE DIAMETER: 2 INCHES 1 CIP INLET OUTSIDE DIAMETER: 4 INCHES INSIDE DIAMTER: 3 INCHES DISCHARGE: CENTER BOTTOM FLANGED DIAMETER: 1.75 INCHES INSIDE DIAMETER: 1 INCH CIP COMPATIBLE MOUNTED ON PIPE STYLE BASE TOP-MOUNTED AGITATOR MOTOR DUAL-HINGED LID CASTER WHEELS INCLUDED AGITATION: DUAL SIDE SCRAPE AGITATOR MOTOR: 208-230/460 V, 60 HZ, THREE PHASE 1,750 RPM

WEXXAR WFT-S BOTTOM SEAL CASE ERECTOR SEALER - USED WEXXAR WFT-S BOTTOM SEAL CASE ERECTOR WITH: PRODUCTION OUTPUT RATE: UP TO 20 CASES PER MINUTE TAPE HEAD: 3 INCHES LEFT CASE BLANK ORIENTATION CASE SIZE RANGE: MINIMUM: 7 LENGTH X 6 WIDTH X 9.5 HEIGHT (INCHES) MAXIMUM: 22 LENGTH X 17 WIDTH X 25 HEIGHT (INCHES) MAGAZINE DIMENSIONS: 72 LENGTH X 26 WIDTH (INCHES) ELECTRICALS: 460 VOLTS, 3 PH, 60 HZ OVERALL DIMENSIONS: 139 LENGTH X 53 WIDTH X 82 HEIGHT (INCHES) MODEL: WFT-S

RED ROCK SVC WRAPAROUND PRESSURE SENSITIVE LABELER HEAD - USED RED ROCK LABELING HEAD WITH: C-STYLE FRAME ADJUSTABLE HEIGHT LABELING HEAD OVERALL DIMENSIONS: WIDTH: 44 INCHES DEPTH: 40 INCHES HEIGHT: 52 INCHES MOUNTED ON CASTERS PREVIOUSLY RUNNING 9.5 INCH L X 6 INCH H LABEL FOR PLANT-BASED CLEANING SOLUTION

KM GRANDPACK 12 BASKET STATIC STEAM RETORT WITH 2 DOOR, MANUAL LOADING. STYLE: STATIC STEAM CAPACITY: 12 BASKETS PRESSURE RATING: MAWP: 43.5 PSI AT 302 F (300 KPA AT 150 C) MDMT: 32 F AT 43.5 PSI (0 C AT 300 KPA) BASKET DIMENSIONS (INCHES): LENGTH: 40 WIDTH: 32 HEIGHT: 27.5 CHAMBER DIMENSIONS: LENGTH: 41 FEET DIAMETER: 48 INCHES OVERALL DIMENSIONS: LENGTH: 44 FEET WIDTH: 54 INCHES HEIGHT: 54 INCHES INFEED: 2 DOORS, MANUAL SWING DOOR BASKET ROLLER RAILS WITH DOUBLE STAINLESS STEEL CHAIN NO. 80 AND GEAR MOTOR DRIVE 3.0 HP FOR BASKET LOADING/UNLOADING DOUBLE DOOR LOCKING SYSTEM FOR SAFETY ONCE VESSEL HAS PRESSURE INSIDE INSULATION: THERMAL INSULATION 50 MM THICK BY ROCKWOOL 80K AND MIRROR POLISHED STAINLESS STEEL CLADDING 0.7 MM THICK. BLOCK AND BLEED VALVES FOR AIR AND WATER SIGHT GLASS WITH SENSORS FOR WATER LEVEL CONTROL STEAM VALVE: BRAND "SPIRAX SARCO", TYPE LE33 WITH BODY IN CAST IRON COMPRESSED AIR VALVE: BRAND "OMAL" SAFETY VALVE: BRAND "ARI" X 2 SET (ASME U-STAMP) PRESSURE GAUGE: PRESSURE GUAGE IN STAINLESS STEEL CAGE 0-6 BARS VESSEL PRESSURE SENSOR: BRAND "ESI" MODEL "GS4200" MIG THERMOMETER: BRAND "TAYLOR" ,SCALE 75-135 C. DIGITAL THERMOMETER: BRAND "WAHL" ONLINE CIRCULAR CHART RECORDER: BRAND "HONEYWELL" MODEL "DR4500AT" , WITH 1 PEN FOR TEMPERATURE RECORDING ASME: ASME U-STAMP CERTIFICATE WITH NATIONAL BOARD NO. REGISTRATION TO MEET PRESSURE VESSEL REGULATION IN GA INCLUDING ENGINEERING, MANUFACTURING, TESTING, INSPECTION TO ASME SECTION VIII, DIVISION I, EDITION 2021. CONTROL SYSTEM: ALLEN BRADLEY PROGRAMMABLE LOGICAL CONTROLLER (PLC) MODEL MICROLOGIX 1400 FOR FULLY AUTOMATIC OPERATION CONSTRUCTION: STAINLESS STEEL SUS 304 6MM THICK ELECTRICAL: OPERATING REQUIREMENTS: 3 PHASE, 60 HERTZ, 480 VOLTS CONTROL VOLTAGE: 120 VOLTS (TRANSFORMER INCLUDED IN CONTROL PANEL) SIGNAL VOLTAGE: 24VDC (POWER SUPPLY INCLUDED IN CONTROL PANEL) LAST APPLICATION: TUNA CANS AT A 5, 7, AND 12 OUNCE WEIGHT. TYPICALLY CYCLE WAS 2 HOURS AND 45 MINUTES. 4 POUND PRODUCT WAS ALSO RAN ON THIS A 5 + HOUR CYCLE.

KM GRANDPACK 12 BASKET STATIC STEAM RETORT WITH MANUAL LOADING. STYLE: STATIC STEAM CAPACITY: 12 BASKETS PRESSURE RATING: MAWP: 43.5 PSI AT 302 F (300 KPA AT 150 C) MDMT: 32 F AT 43.5 PSI (0 C AT 300 KPA) BASKET DIMENSIONS (INCHES): LENGTH: 40 WIDTH: 32 HEIGHT: 27.5 CHAMBER DIMENSIONS: LENGTH: 41 FEET DIAMETER: 48 INCHES OVERALL DIMENSIONS: LENGTH: 44 FEET WIDTH: 54 INCHES HEIGHT: 54 INCHES INFEED: 2 DOORS, MANUAL SWING DOOR BASKET ROLLER RAILS WITH DOUBLE STAINLESS STEEL CHAIN NO. 80 AND GEAR MOTOR DRIVE 3.0 HP FOR BASKET LOADING/UNLOADING DOUBLE DOOR LOCKING SYSTEM FOR SAFETY ONCE VESSEL HAS PRESSURE INSIDE INSULATION: THERMAL INSULATION 50 MM THICK BY ROCKWOOL 80K AND MIRROR POLISHED STAINLESS STEEL CLADDING 0.7 MM THICK. BLOCK AND BLEED VALVES FOR AIR AND WATER SIGHT GLASS WITH SENSORS FOR WATER LEVEL CONTROL STEAM VALVE: BRAND "SPIRAX SARCO", TYPE LE33 WITH BODY IN CAST IRON COMPRESSED AIR VALVE: BRAND "OMAL" SAFETY VALVE: BRAND "ARI" X 2 SET (ASME U-STAMP) PRESSURE GAUGE: PRESSURE GUAGE IN STAINLESS STEEL CAGE 0-6 BARS VESSEL PRESSURE SENSOR: BRAND "ESI" MODEL "GS4200" MIG THERMOMETER: BRAND "TAYLOR" ,SCALE 75-135 C. DIGITAL THERMOMETER: BRAND "WAHL" ONLINE CIRCULAR CHART RECORDER: BRAND "HONEYWELL" MODEL "DR4500AT" , WITH 1 PEN FOR TEMPERATURE RECORDING ASME: ASME U-STAMP CERTIFICATE WITH NATIONAL BOARD NO. REGISTRATION TO MEET PRESSURE VESSEL REGULATION IN GA INCLUDING ENGINEERING, MANUFACTURING, TESTING, INSPECTION TO ASME SECTION VIII, DIVISION I, EDITION 2021. CONTROL SYSTEM: ALLEN BRADLEY PROGRAMMABLE LOGICAL CONTROLLER (PLC) MODEL MICROLOGIX 1400 FOR FULLY AUTOMATIC OPERATION CONSTRUCTION: STAINLESS STEEL SUS 304 6MM THICK ELECTRICAL: OPERATING REQUIREMENTS: 3 PHASE, 60 HERTZ, 480 VOLTS CONTROL VOLTAGE: 120 VOLTS (TRANSFORMER INCLUDED IN CONTROL PANEL) SIGNAL VOLTAGE: 24VDC (POWER SUPPLY INCLUDED IN CONTROL PANEL) LAST APPLICATION: TUNA CANS AT A 5, 7, AND 12 OUNCE WEIGHT. TYPICALLY CYCLE WAS 2 HOURS AND 45 MINUTES. 4 POUND PRODUCT WAS ALSO RAN ON THIS A 5 + HOUR CYCLE.

2000 PILLAR UNIFOILER U2P INDUCTION SEALER WITH FLAT HEAD ON CASTER BASE FRAME - USED INDUCTION SEALER WITH: FLAT SEALING HEAD: LENGTH: 26 INCHES WIDTH: 5 INCHES HAND CRANK HEIGHT ADJUSTMENT PUSH BUTTON CONTROLS DIGITAL READOUT AIR COOLED ELECTRICAL REQUIREMENTS: 208/240 VOLTS, 60 HERTZ, 1 PHASE MOUNTED ON CASTERS S/N:

PACE M500 STAINLESS STEEL AUTOMATIC BULK BOTTLE UNSCRAMBLER WITH INFEED HOPPER. SPEED: UP TO 300 BOTTLES PER MINUTE (DEPENDING ON PRODUCT SPECIFICATIONS). BOWL DIMENSIONS: DIAMETER: 60 INCHES, DEPTH: 18 INCHES. CAPACITY: 40 CUBIC FEET. INFEED HEIGHT: 50 INCHES. DISCHARGE WIDTH: 32 INCHES. CONVEYOR DIMENSIONS: LENGTH: 70 INCHES, WIDTH: 12 INCHES. CLEAT CENTERS: 13 INCHES. CLEAT HEIGHT: 2 INCHES. INFEED HOPPER DIMENSIONS: INCLINE LENGTH: 60 INCHES, STRAIGHT TOP LENGTH: 30 INCHES, WIDTH: 44 INCHES. CONVEYOR: LENGTH: 70 INCHES, WIDTH: 12 INCHES. CLEATS: CENTERS: 13 INCHES, HEIGHT: 2 INCHES. DISCHARGE WIDTH: 33 INCHES. ELECTRICAL: 220 VOLTS, 3 PHASE, 60 HZ.

PEARSON CE35 GLUE BOTTOM SEAL STAINLESS STEEL LEFT HANDED CASE ERECTOR - USED PEARSON CE35 CASE ERECTOR WITH: PEARSONS CE35 CASE ERECTOR IS A MACHINE CAPABLE OF ERECTING AND BOTTOM SEALING RSC, HSC, CSSC, AND RSC W/INTEGRAL DIVIDER CASES. AT SPEEDS UP TO 35 CASES PER MINUTE, THE SMALL FOOTPRINT MAKES IT IDEAL FOR PRODUCTION AREAS AND AN OPTIONAL LOW-LEVEL, VERTICAL MAGAZINE MAKES IT EASY TO LOAD BLANKS INTO THE MACHINE FOR ERECTING. THE CE35 INTERMEDIATE FRAME MODELS ARE THE ANSWER FOR LARGER CASE RANGES. OUTPUT: UP TO 35 CASES PER MINUTE, DEPENDING ON MATERIALS AND APPLICATION ERECTED CASE SIZE RANGE: MINIMUM (INCHES): 6 LONG X 5 WIDE X 3.5 DEEP MAXIMUM (INCHES): 23.5 LONG X 16 WIDE X 18.5 DEEP EXTENDED CASE MAGAZINE CHAIN DRIVEN DISCHARGE GLUE UNIT SET UP TO RUN LEFT HAND CASES CONTROLS: ALLEN-BRADLEY TOUCH SCREEN CONTROLS INCLUDES START, E-STOP & CYCLE STAINLESS STEEL CONSTRUCTION ELECTRICAL: 460 VOLTS, 3/1 PHASE, 60 HERTZ

ADMIX ROTOMIXX 125RXG 150 HYGIENIC LOW SHEAR BATCH MIXER WITH: THE ROTOMIXX IS AN ALL-STAINLESS STEEL PORTABLE MIXER DESIGNED TO MEET STRINGENT CIP WASHDOWN, PRESSURE WASHING, AND STEAM CLEANING CONDITIONS. THE ROTOMIXX IMPELLERS COMBINE 25+ YEARS OF HYDROFOIL BLADE TECHNOLOGY INTO THREE DISTINCT, HIGH PERFORMANCE DESIGNS, INCLUDING OUR 3-BLADE JETFOIL, OUR ULTRA SANITARY J-PROP, AND OUR UNIQUE WIDE BLADE MAXIFOIL. ALL ARE DESIGNED TO PROVIDE UP TO 200% MORE FLOW PER HORSEPOWER OVER CONVENTIONAL IMPELLERS. PROPELLER TYPE: JETFOIL 18-INCH PROPELLER DIAMETER 3-BLADE SETBOLTED SHAFT TILT AND SWIVEL FEATURE ADJUSTABLE CLAMP MOUNTING SYSTEM SHAFT SPECIFICATIONS: 233 ROTATIONS PER MINUTE 45.24-INCH LONG 1.25-INCH DIAMETER SOLID ONE PIECE SHAFT 1.5 HORSEPOWER MOTOR 316 SS FINISH ELECTRICAL REQUIREMENTS: 230/460 VOLTS, 3 PHASE, 60 HERTZ MIXER WAS NEVER PUT INTO PRODUCTION BUT WAS INTENDED TO BE USED TO MIX A 317 GALLON BATCH SIZE WITH A VISCOSITY OF 10,000 CPS. MODEL: 125RXG 150

FORTRESS STEALTH INCLINE METAL DETECTOR WITH 23"W X 2"H APERTURE AND 60"H DISCHARGE. EFFECTIVE APERTURE DIMENSIONS: 23 INCHES WIDE X 2.5 INCHES TALL. APERTURE DIMENSIONS: 24 INCHES WIDE X 4 INCHES TALL. CONVEYOR DIMENSIONS: 22 INCHES WIDE X 96 INCHES LONG. INFEED HEIGHT: 22 INCHES. DISCHARGE HEIGHT: 61 INCHES. LEFT TO RIGHT PRODUCT FLOW. PRODUCT DROP-OUT REJECT. .5 HORSE POWER CONVEYOR MOTOR. VARIABLE CONVEYOR SPEEDS. STAINLESS STEEL CONSTRUCTION. MODEL: SC-CONV-96SSH22FG

RYSON 1600-500 INCLINING SPIRAL ELEVATOR CONVEYOR - USED RYSON DECLINING SPIRAL CONVEYOR WITH: CONVEYOR WIDTH: 20 INCHES WEIGHT CAPACITY: 50 POUNDS PER LINEAR FOOT TOTAL WEIGHT: UP TO 3600 POUNDS SPEED: UP TO 200 FEET PER MINUTE DEPENDING ON PRODUCT AND APPLICATION DISTANCE BETWEEN TIERS: 34 INCHES PRODUCT CLEARANCE: 28 INCHES INFEED HEIGHT: 18 INCHES DISCHARGE HEIGHT: 144 INCHES OUTSIDE DIAMETER: 85 INCHES CENTERLINE DIAMETER: 42 INCHES OVERALL DIMENSIONS: DIAMETER: 85 INCHES HEIGHT: APPROXIMATELY 150 INCHES DRIVE MOTOR: 2 HORSEPOWER ELECTRICAL: 3 PHASE, 60 HZ, 230/460 VOLTS PREVIOUSLY USED IN POPCORN FACILITY

STAINLESS STEEL RIBBON BLENDER WITH DRIVE MOTOR - USED RIBBON BLENDER WITH: CAPACITY: 5 FEET3 MIXER RPM: 46 CHAMBER DIMENSIONS: LENGTH: 18 INCHES WIDTH: 32 INCHES DEPTH: 22 INCHES OVERALL DIMENSIONS: LENGTH: 61 INCHES WIDTH: 29 INCHES HEIGHT: 44 INCHES DISCHARGE: BOTTOM-CENTER DISCHARGE DIAMETER: FLANGED: 4.5 INCHES INSIDE DIAMETER: 3.5 INCHES AGITATION: DUAL RIBBON SINGLE SHAFT MOUNTED ON FLANGED FEET CONSTRUCTION: STAINLESS STEEL MOTOR: 3 HP MOTOR ELECTRICAL: 230/460 V, 60 HZ, THREE PHASE

2000 FANUC SR-6IA SCARA ROBOTIC PICK-AND-PLACE SYSTEM WITH: MAXIMUM LOAD CAPACITY: 6 KILOGRAMS MAXIMUM REACH: 650 MM CONTROLLED AXES: 4 REPEATABILITY: J1, J2: 0.01 MM J3: 0.01 MM J4: 0.004 MOTION RANGE: J1: 148 J2: 150 J3: 210 MM J4: 720 MAXIMUM SPEED: J1: 440 DEGREES PER SECOND J2: 700 DEGREES PER SECOND J3: 2,000 MM PER SECOND J4: 2500 DEGREES PER SECOND MECHANICAL WEIGHT: 30 KILOGRAMS R-30 IB COMPACT PLUS CONTROLLER ELECTRICAL: 1 PHASE, 50/60 HZ, 200 VOLTS

ACASI RU 3200 42 INCH DIAMETER UNSCRAMBLING TABLE - ACASI RU 3200 42" DIA. UNSCRAMBLING ROTARY TABLE WITH: PRODUCTION OUTPUT RATE: UP TO 150 CONTAINERS PER MINUTE TABLE DIAMETER: 42 INCHES BOTTLE ORIENTING GUIDE DC GEAR MOTOR VARIABLE SPEED CONTROL BY POTENTIOMETER OVERALL DIMENSIONS: 42 DIAMETER X 51.2 HEIGHT (INCHES) MODEL: RU 3200

LIQUID PROCESS CIRCULATION AND PUMP SYSTEM WITH 165 GALLON STAINLESS STEEL SINGLE WALL TANK - USED STAINLESS STEEL TANK AND PUMP SYSTEM WITH: STAINLES STEEL TANK: CAPACITY: 165 GALLONS SINGLE WALL SPX WAUKESHA CHERRY BURRELL CENTRIFUGAL PUMP 15 HP GRUNFOS PUMP (10) TRI CLOVER AIR ACTUATORS ABB TB82 TRANSMITTER TEMPERATURE GAUGE START/STOP SWITCH STAIRS AIR ACCUMULATION TANK SYSTEM MOUNTED ON A STAINLESS STEEL BASE

165 GALLON LIQUID IMMERSION BLENDING SYSTEM - USED CIRCULATION AND PUMP SYSTEM WITH: TANK: CAPACITY: 165 GALLONS STAINLESS STEEL CONSTRUCTION ROTOSOLVER AGITATOR GRUNFOS PUMP GAMAJET SPRAY ABB PLASTI-BOND REDHOT PLATFORM AIR ACCUMULATION TANK SKIDDING

750 GALLON 316L STAINLESS STEEL JACKETED MIX TANK - USED WALKER MIX TANK WITH: CAPACITY: 750 GALLONS FLAT TOP, DISH BOTTOM JACKET RATING: MAWP: 75 PSI 320 F MDMT: 75 PSI -20 F AGITATION: SINGLE SHAFT BOTTOM SWEEP BAFFLE DRIVEN BY A 2 HORSEPOWER, 230/460 VOLTS, 60 HERTZ, 3 PHASE MOTOR DISCHARGE: BOTTOM CENTER 2 INCH DIAMETER CIP SPRAY BALL VARIOUS 2 INCH INLETS AND FITTINGS TOP MOUNTED HINGED MANWAY 316L STAINLESS STEEL CONSTRUCTION MOUNTED ON 4 LEGS

WEXXAR WF-2T TAPE BOTTOM SEAL CASE ERECTOR - USED WEXXAR WF-2T TAPE BOTTOM SEAL CASE ERECTOR WITH: PRODUCTION OUTPUT RATE: UP TO 20 CASES PER MINUTE MINIMUM CASE DIMENSIONS: 7 LENGTH X 5 WIDTH X 5 HEIGHT INCHES MAXIMUM CASE DIMENSIONS: 24 LENGTH X 17 WIDTH X 16 HEIGHT INCHES CASE MAGAZINE DIMENSIONS: 67 LENGTH X 39 WIDTH INCHES CASE MAGAZINE HEIGHT: 33 INCHES DISCHARGE HEIGHT: 27 INCHES AIR REQUIREMENTS: 0.3 CUBIC FEET PER CYCLE 90 POUNDS PER SQUARE INCH ELECTRICALS: PHASE: 3 VOLTAGE: 460 AMPERAGE: 1.5 FREQUENCY: 60 HERTZ OVERALL DIMENSIONS: 148 LENGTH X 50 WIDTH X 75 HEIGHT INCHES S/N:

COMBI 2EZ HOT MELT FOLD OVER CASE ERECTOR WITH SYSTEM AND MAGAZINE. CASE SIZE RANGE: MINIMUM: 8 INCHES LONG X 8 INCHES WIDE X 5 INCHES TALL MAXIMUM: 18 INCHES LONG X 9 INCHES WIDE X 16 INCHES TALL. MANUAL PUSH BUTTON CONTROLS. NORDSON HOT MELT GLUE UNIT. VACUUM BLANK CARTON PICK-OFF. OUTPUT: APPROXIMATELY 6-8 CASES PER MINUTE, DEPENDING ON CASE SIZE. WELDED TUBULAR FRAME. RUNS FULL OVERLAP BOTTOM CONTAINER WITH MINOR FLAPS MEETING (FOL) BUT NOT A STANDARD RSC. RUNS LEFT HAND CASES.

BEVCO M150 BOTTLE/CAN GRIPPER AND AIR RINSER WITH IONIZED AIR. GRIPPER-STYLE RINSERS ARE ABLE TO RINSE A WIDE VARIETY OF CONTAINER TYPES, INCLUDING ROUND, SQUARE, OVAL, TAPERED, AND OTHER BOTTLE SHAPES, IN MANY DIFFERENT MATERIALS (GLASS, PET, HDPE, ALUMINUM). DESIGNED FOR MANY DIFFERENT FOOD AND BEVERAGE LINES, SUCH AS WATER, MILK, JUICE, BEER, CIDER, WINE, KOMBUCHA, JAM, ETC. BEVCO'S RINSERS ARE DESIGNED TO REMOVE LOOSE PARTICULATE OR DUST FROM BOTTLES, AND IN SOME CASES, CAN ALSO BE UTILIZED AS A PART OF A CHEMICAL SANITATION SYSTEM. ABLE TO RINSE A WIDE VARIETY OF CONTAINER TYPES, INCLUDING ROUND, SQUARE, OVAL, TAPERED, AND OTHER BOTTLE SHAPES, IN MANY DIFFERENT MATERIALS (GLASS, PET, HDPE, ALUMINUM). HANDLES CONTAINER SIZES FROM 1.5-9 INCHES IN WIDTH AND UP TO 13 INCHES IN HEIGHT. OVERALL DIMENSIONS (INCHES): LENGTH: 112 WIDTH: 36 HEIGHT: 94. RINSE STYLE: AIR. CONTAINER GRIPPER BELTS. 2 SPEED FUNCTION. VACUUM MANIFOLD. PUSH BUTTON CONTROLS. STAINLESS STEEL CONSTRUCTION. ELECTRICAL: 3 PHASE, 60 HERTZ, 460 VOLTS, 3.76 AMPS. S/N:

SACMI FORMSLEEVER 500 LABELER. SPEEDS: UP TO 866 PER MINUTE. SUITABLE FILMS: PET, OPS, PO, PVC, PLA, OPP AND OTHERS. MAXIMUM LABEL SIZE: 175MM/6.9 INCHES. MINIMUM LABEL SIZE: 30MM/1.2 INCHES. MAXIMUM CONTAINER SIZE: 350MM/13.8 INCHES. MINIMUM CONTAINER SIZE: 150MM/5.9 INCHES. MAIN TURRET: CONTAINERS ARE ROTATED AROUND AXIS SO LABELS CAN BE APPLIED. TUBULAR SLEEVE APPLIED. SLEEVE CAN BE FULL OR PARTIAL BODY. LABELING UNIT: PHOTOCELL NEAR INLET WHEEL GENERATES SIGNAL AND STARTS LABELING PROCESS. LABELING TAPE TRANSFERRED FROM REEL TO DRIVE ROLLER. DRIVE ROLLER ADJUSTS TO MAKE SURE CUTTING POINT IS CORRECT. SOLVENT APPLIED TO LABEL AND SLEEVE IS SEALED. REEL UNWINDER. CONTROL CABINET. ELECTRICALS: 480 VOLTAGE / 3 PHASE / 60 HERTZ. OPERATION: AUTOMATICALLY LOADS, APPLIES WRAP AROUND LABELS TO CONTAINERS, AND THEN UNLOADS THEM. CONTAINERS ENTER ON A SINGLE ROW CONVEYOR AND TRANSFERRED TO THE MAIN TURRET. MODEL: 8LRFS500A

MOEN BLISS PF106-BIFQV BLISS CASE FORMER MACHINE. FORMS A 3 PIECE BLISS BOX OUT OF END PANELS, INTERNAL FLANGES, AND BODY WRAP. PRODUCTION OUTPUT RATE: UP TO 22 CASES PER MINUTE, DEPENDING ON APPLICATION. MINIMUM CASE SIZE: 8 LENGTH X 8 WIDTH X 4 HEIGHT (INCHES). MAXIMUM CASE SIZE: 24 LENGTH X 24 WIDTH X 12 HEIGHT (INCHES). FLAT DIE CUT BLANK RANGE: BODY WRAP LENGTH: 16 TO 56 INCHES. BODY WRAP WIDTH: 12 TO 29 INCHES. END PANEL WIDTH: 8 TO 28 INCHES. END PANEL HEIGHT: 4 TO 17 INCHES. NORDSON PROBLUE HOT MELT GLUE SYSTEM. AIR REQUIREMENTS: 85 POUNDS PER SQUARE INCH. ALLEN BRADLEY TOUCH SCREEN CONTROLS. POWER SUPPLY: 480 VOLTAGE / 3 PHASE / 60 HERTZ. APPROX. OVERALL DIMENSIONS: 144 LENGTH X 144 WIDTH X 108 HEIGHT (INCHES). MODEL: PF106-BIFQV

HEATCRAFT REFRIGERATION PRODUCTS BOHN BCH0035LCACZA0200 CONDENSER - USED HEATCRAFT BCH0035LCACZA0200 CONDENSER WITH: 11630 BTU PER HOUR (2) CONDENSER FAN MOTOR(S): 1/15 HORSEPOWER REFRIGERANT TYPE: R-404A REMOVABLE CABINETS ELECTRONIC TIMER ELECTRICAL REQUIREMENTS: 208-230 VOLTS 60 HZ 3 PHASE HEAVY DUTY STEEL CONSTRUCTION MODEL: BCH0035LCACZA0200

HAPMAN 96 INCH LONG STAINLESS STEEL AUGER CONVEYOR WITH .5 HP MOTOR AND FLAT STYLE SCREW. HOPPER DIMENSIONS: LENGTH: 36 INCHES WIDTH: 36 INCHES HEIGHT: 36 INCHES. SCREW DIMENSIONS: PITCH: 2 INCHES DIAMETER: 1.5 INCHES FLIGHTING DIAMETER: 0.5 INCH. HOPPER INFEED HEIGHT: 48 INCHES. AUGER OUTFEED HEIGHT: 82 INCHES. AUGER LENGTH: 96 INCHES. STAINLESS STEEL FRAME. PRODUCT GRATE. MOUNTED ON LOCKING CASTERS. MOTOR: 0.5 HP. ELECTRICAL: 240/360 V.

AXON DUAL HOTWIND 2" BY 2.5" DUAL ZONE HEAT TUNNEL FOR NECK BANDS - USED AXON NECK BAND HEAT SHRINK TUNNEL WITH: APERTURE DIMENSIONS (INCHES): WIDTH: 2 HEIGHT: 2.5 TUNNEL LENGTH: 34 INFEED HEIGHT: 38 INCHES (APPROXIMATELY) OVERALL DIMENSIONS (INCHES): LENGTH: 50 WIDTH: 50 HEIGHT: 87 HEATING ZONES: 2 EQUIPPED WITH (2) LEISTER HOTWIND SYSTEMS: AIR VOLUME (68 F): 7.1 - 31.8 CUBIC FEET PER MINUTE MAX AIR OUTLET TEMPERATURE: 1202 F POWER: 3700 WATTS MOUNTED ON STAINLESS STEEL BASE STAINLESS STEEL CONTACT PARTS PNEUMATICS: PSI: 80 CFM: 5 ELECTRICAL: SINGLE PHASE, 60 HERTZ, 220 VOLTS, 20 AMPS LAST APPLICATION: NECK BAND SHRINKING MODEL: DUAL LEISTER HOTWIND

HEATCRAFT REFRIGERATION PRODUCTS BOHN BCH0035LCACZA0200 CONDENSER - USED HEATCRAFT BCH0035LCACZA0200 CONDENSER WITH: 11630 BTU PER HOUR (2) CONDENSER FAN MOTOR(S): 1/15 HORSEPOWER REFRIGERANT TYPE: R-404A REMOVABLE CABINETS ELECTRONIC TIMER ELECTRICAL REQUIREMENTS: 208-230 VOLTS 60 HZ 3 PHASE HEAVY DUTY STEEL CONSTRUCTION MODEL: BCH0035LCACZA0200

2000 MATRIX PROTEUS 2840SER VERTICAL FORM FILL AND SEAL. SEAL JAW LENGTH: 12 INCHES. MAXIMUM FILM WIDTH: 22 INCHES. FORMER: DSL FORMING COLLAR. DIAMETER: 2.5 INCHES. PILLOW BAGS. PRINT REGISTRATION. DISCHARGE HEIGHT: 20 INCHES. MARKEM SMART DATE 2 DATE CODER. ALLEN-BRADLEY PANELVIEW PLUS 1000 TOUCHSCREEN HMI. FORMING COLLAR MAKES A LEFT OVER RIGHT FIN SEAL. S/N: 75361DSL

36 INCH ROTARY ACCUMULATION TABLE - USED ROTARY ACCUMULATION TABLE WITH: ROTARY TABEL: DIAMETER: 36 INCHES HEIGHT: 34 INCHES MATSOOKA SPEED CONTROL: 60 HERTZ 110 VOLTS

MPAC SEMI AUTOMATIC TOP AND BOTTOM 2 INCH CASE TAPER - USED MPAC TOP AND BOTTOM MANUAL CASE TAPER WITH: INFEED AND DISCHARGE HEIGHT: 32 INCHES ROLLER CENTERS: 3 INCHES SIDE BELT WIDTH: 2.75 INCHES DEKKA SE-22 TAPE HEADS (2): WIDTH: 2 INCHES TAPING SPEED: 80 TO 120 FEET PER MINUTE TOP AND BOTTOM CASE TAPING PHOTO EYE SENSORS TOOLLESS GRIPPER BELT ADJUSTMENT THREADED LEVELING FEET PAINTED STEEL FRAME DUAL DRIVE MOTORS: 0.33 HP MOTOR ELECTRICAL: 3 PHASE, 60 HZ, 230/460 VOLTS

WEXXAR WFT 3 INCH TAPE BOTTOM SEAL CASE ERECTOR. PRODUCTION OUTPUT RATE: UP TO 20 CASES PER MINUTE. TAPE HEAD: 3 INCHES. LEFT HANDED CASE BLANK. CASE SIZE RANGE: MINIMUM: 7 LENGTH X 6 WIDTH X 6 HEIGHT (INCHES), MAXIMUM: 22 LENGTH X 17 WIDTH X 20 HEIGHT (INCHES). MAGAZINE DIMENSIONS: 72 LENGTH X 31.5 WIDTH (INCHES). AIR REQUIREMENTS: 20 CUBIC FEET PER MINUTE 90 POUNDS PER SQUARE INCH. ELECTRICAL: 230 VOLTS, 3 PH, 60 HZ, 4.1 AMPS. OVERALL DIMENSIONS: 170 LENGTH X 50 WIDTH X 75 HEIGHT (INCHES).

AXON DUAL LEISTER HOTWIND DUAL ZONE HEAT TUNNEL FOR NECK BANDS - USED AXON NECK BAND HEAT SHRINK TUNNEL WITH: APERTURE DIMENSIONS (INCHES): WIDTH: 2 HEIGHT: 2.5 TUNNEL LENGTH: 34 INFEED HEIGHT: 38 INCHES (APPROXIMATELY) OVERALL DIMENSIONS (INCHES): LENGTH: 50 WIDTH: 50 HEIGHT: 87 HEATING ZONES: 2 EQUIPPED WITH (2) LEISTER HOTWIND SYSTEMS: AIR VOLUME (68 F): 7.1 - 31.8 CUBIC FEET PER MINUTE MAX AIR OUTLET TEMPERATURE: 1202 F POWER: 3700 WATTS MOUNTED ON STAINLESS STEEL BASE STAINLESS STEEL CONTACT PARTS ELECTRICAL: SINGLE PHASE, 60 HERTZ, 220 VOLTS, 20 AMPS LAST APPLICATION: NECK BAND SHRINKING

WEXXAR WFT 3 INCH TAPE BOTTOM SEAL CASE ERECTOR - USED WEXXAR WFT TAPE BOTTOM SEAL CASE ERECTOR WITH: PRODUCTION OUTPUT RATE: UP TO 20 CASES PER MINUTE TAPE HEAD: 3 INCHES LEFT HANDED CASE BLANK MINIMUM CASE SIZE: 7 LENGTH X 6 WIDTH X 6 HEIGHT (INCHES) MAXIMUM CASE SIZE: 22 LENGTH X 17 WIDTH X 20 HEIGHT (INCHES) MAGAZINE DIMENSIONS: 72 LENGTH X 31.5 WIDTH (INCHES) AIR REQUIREMENTS: 20 CUBIC FEET PER MINUTE 90 POUNDS PER SQUARE INCH ELECTRICALS: PHASE: 3 AMPERAGE: 4.1 VOLTAGE: 230 FREQUENCY: 60 HERTZ OVERALL DIMENSIONS: 170 LENGTH X 50 WIDTH X 75 HEIGHT (INCHES) S/N:

AXON DUAL LEISTER HOTWIND DUAL ZONE HEAT TUNNEL FOR NECK BANDS - USED AXON NECK BAND HEAT SHRINK TUNNEL WITH: APERTURE DIMENSIONS (INCHES): WIDTH: 2 HEIGHT: 2.5 TUNNEL LENGTH: 34 INFEED HEIGHT: 38 INCHES (APPROXIMATELY) OVERALL DIMENSIONS (INCHES): LENGTH: 50 WIDTH: 50 HEIGHT: 87 HEATING ZONES: 2 EQUIPPED WITH (2) LEISTER HOTWIND SYSTEMS: AIR VOLUME (68 F): 7.1 - 31.8 CUBIC FEET PER MINUTE MAX AIR OUTLET TEMPERATURE: 1202 F POWER: 3700 WATTS MOUNTED ON STAINLESS STEEL BASE STAINLESS STEEL CONTACT PARTS ELECTRICAL: SINGLE PHASE, 60 HERTZ, 220 VOLTS, 20 AMPS LAST APPLICATION: NECK BAND SHRINKING

8-HEAD STAINLESS STEEL INLINE GRAVITY PRESSURE FILLER WITH: NUMBER OF NOZZLES: 8 NOZZLE DIAMETER: 3/4 INCH STAINLESS STEEL HOPPER PUSH BUTTON CONTROLS MOUNTED ON (4) LEGS STAINLESS STEEL CONSTRUCTION ELECTRICAL REQUIREMENTS: 230/460 VOLTS, 60 HERTZ, 3 PHASE

SOUTHERN CALIFORNIA ST1100 FRONT AND BACK LABELER WITH: SPEED: UP TO 1,100 LINEAR INCHES PER MINUTE WEB WIDTH: 6 INCHES CONVEYOR DIMENSIONS (MISSING BELT): WIDTH: 6 INCHES LENGTH: 92 INCHES LABEL SIZE: MINIMUM: WIDTH: 0.5 INCHES LENGTH: 0.5 INCHES MAXIMUM: WIDTH: 6 INCHES LENGTH: 18 INCHES CORE DIAMETER: 1 INCH MOUNTED ON CASTERS PUSH-BUTTON CONTROLS WITH DIGITAL READOUT ELECTRICAL REQUIREMENTS: 120 VOLTS, 60 HERTZ, SINGLE PHASE MODEL: ST1100

ECONOSEAL E2000 AUTOMATIC STAINLESS STEEL HORIZONTAL CARTONER - USED ECONOSEAL HORIZONTAL CARTONER WITH: SPEED: UP TO 25 CARTONS PER MINUTE, DEPENDING ON CARTON SIZE AND APPLICATION MINIMUM CARTON DIMENSIONS: LENGTH: 1 INCH WIDTH: 0.75 INCHES HEIGHT: 2.5 INCHES MAXIMUM CARTON DIMENSIONS: LENGTH: 12 INCHES WIDTH: 4 INCHES HEIGHT: 12 INCHES INFEED HEIGHT: 38 INCHES DISCHARGE HEIGHT: 32.5 INCHES BUCKET DIMENSIONS: LENGTH: 8 INCHES WIDTH: 5.5 INCHES HEIGHT: 4.5 INCHES BUCKET CENTERS: 5.5 INCHES MAGAZINE DIMENSIONS: LENGTH: 9.5 INCHES WIDTH: 8.5 INCHES AIR REQUIREMENTS: 80 PSI ELECTRICAL: 1 PHASE, 60 HZ, 220 VOLTS PREVIOUSLY USED IN BEVERAGE APPLICATION

PACKLAB FRONT BACK AND WRAPAROUND LABELER. VERSATILE LABELING MACHINE DESIGNED TO APPLY LABELS TO BOTH THE FRONT AND BACK OF CONTAINERS, AS WELL AS WRAPAROUND LABELS FOR CYLINDRICAL PRODUCTS. FEATURES ADJUSTABLE SETTINGS TO ACCOMMODATE VARIOUS CONTAINER SIZES AND LABEL TYPES, OFFERING FLEXIBILITY FOR DIFFERENT PACKAGING NEEDS. OPERATES AT HIGH SPEEDS, ENSURING EFFICIENT AND PRECISE LABEL APPLICATION IN FAST-PACED PRODUCTION ENVIRONMENTS. BUILT FOR RELIABILITY AND EASE OF USE, ENHANCES PRODUCTIVITY WHILE ENSURING CONSISTENT LABELING ACCURACY. OUTPUT: UP TO 80 INCHES PER MINUTE DEPENDING ON LABEL SIZES. CONVEYOR DIMENSIONS: 3.25 INCHES WIDE X 116 INCHES LONG. FRONT/BACK LABEL SIZE RANGE: WRAP BELT: 23 INCHES LONG X 4 INCHES. WEB WIDTH: 7.5 INCHES. 1.5 INCH DIAMETER INNER CORE. ELECTRICAL REQUIREMENTS: 480 / 50/60 HERTZ / 3 PHASE.

11" X 13" METAL DETECTOR - USED LOMA IQ3 METAL DETECTOR HEAD WITH: APERTURE DIMENSIONS: HEIGHT:11.75 INCHES WIDTH: 13.75 INCHES OVERALL DIMENSIONS: LENGTH: 34.5 INCHES WIDTH: 20 INCHES HEIGHT: 30 INCHES TOUCHSCREEN HMI ENVIRONMENT RATING: IP66 304 STAINLESS STEEL CONSTRUCTION WITH POLISH FINISH MAX CURRENT: 2 AMPS ELECTRICALS: 120 VOLTS, 60 HZ, MODEL: IQ3

ECONOSEAL E2000 CARTONER WITH INFEED CONVEYOR - USED ECONOSEAL HORIZONTAL CARTONER WITH: SPEED: UP TO 1500 CARTONS PER HOUR DEPENDING ON CARTON SIZE AND APPLICATION MINIMUM CARTON DIMENSIONS: LENGTH: 1 INCH WIDTH: 0.75 INCHES HEIGHT: 2.5 INCHES MAXIMUM CARTON DIMENSIONS: LENGTH: 12 INCHES WIDTH: 4 INCHES HEIGHT: 12 INCHES INFEED HEIGHT: 38 INCHES DISCHARGE HEIGHT: 32.5 INCHES BUCKET DIMENSIONS: LENGTH: 8 INCHES WIDTH: 5.5 INCHES HEIGHT: 4.5 INCHES BUCKET CENTERS: 5.5 INCHES MAGAZINE DIMENSIONS: LENGTH: 9.5 INCHES WIDTH: 8.5 INCHES AIR REQUIREMENTS: 80 PSI ELECTRICAL: 1 PHASE, 60 HZ, 220 VOLTS PREVIOUSLY USED IN BEVERAGE APPLICATION

75 GALLON STAINLESS STEEL KETTLE WITH AGITATION - USED LEE KETTLE WITH: CAPACITY: 75 GALLONS (~283 LITERS) TOP-MOUNTED PROPELLER AGITATION TOP OPENING DIAMETER: 16 INCHES TOTAL DIAMETER: 30 INCHES DISCHARGE: HEIGHT: 15 INCHES WIDTH: 2 INCHES VARIOUS INLETS AND OUTLETS STAINLESS STEEL CONSTRUCTION MOUNTED ON LOCKABLE CASTERS 0.33 HP MOTOR ELECTRICAL: 208-230/460 VOLTS, 60 HZ, THREE PHASE MODEL: 75 "PBT"

USED DRAISWERKE TURBULENT SUPERFLUSHER TSF-160 MIXER WITH: BATCH, HEAVY DUTY HORIZONTAL MIXER DESIGNED TO MIX AND KNEAD PIGMENT AND OTHER FLUSHES WITH SUFFICIENT ENERGY TO DRIVE WATER OUT OF THE PRESS CAKES IMPARTS THE NECESSARY SHEAR FOR DISPERSION AND DRYING AND EXTREMELY EFFICIENT VACUUM DRYING STAINLESS STEEL CONTACT PARTS CAPACITY: 160 LITERS, APPROXIMATELY 40 GALLONS 60 HORSEPOWER DRIVE MOTOR MODEL: TURBULENT SUPERFLUSHER TSF-160

DCI 240 GALLON STAINLESS STEEL JACKETED TANK WITH 316 STAINLESS STEEL. CAPACITY: 240 GALLONS STYLE: VERTICAL JACKETED DOME TOP DISH BOTTOM TANK DIMENSIONS (INCHES): DIAMETER: 42 HEIGHT: 42 OVERALL DIMENSIONS (INCHES): LENGTH: 52 WIDTH: 52 HEIGHT: 84 MANWAY DIAMETER: 18 INCHES INTERNAL JACKET RATING: 30 PSIG INLETS (2): 2 INCHES CENTER BOTTOM OUTLET: 2.5 INCHES CIP INLETS WITH SPRAYBALL (2): 3 INCHES SIGHT DETECTOR GAUGE 316 STAINLESS MOUNTED ON CASTERS AND A STAINLESS STEEL FRAME

AMF B30 HPS STAINLESS STEEL BREAD BASKET WASHER AND DRYER - AMF WASHING AND DRYING SYSTEM OFFERS OPTIMIZED WATER AND AIR HEATING SOLUTIONS BY MEANS OF GAS, STEAM OR HEAT RECOVERY SYSTEM. BASKETS ARE CLEANED AND DRIED IN A CONTINUOUS MOTION WITHOUT BASKET ACCUMULATION. BASKETS PASS THROUGH A HIGH-PERFORMANCE NOZZLE SYSTEM USING FILTERED HOT WATER. FOR MAXIMUM CLEANING EFFICIENCY, FRESH WATER INTAKE IS CONTROLLED TO ELIMINATE WASH SOLUTION TEMPERATURE DROP. BASKETS ARE DRIED BY AN AIR KNIFE TECHNOLOGY COMBINED WITH A MOISTURE ELIMINATOR SYSTEM THAT RECIRCULATES AIR AND ELIMINATES EXCESS MOISTURE WHILE REDUCING OVERALL ENERGY CONSUMPTION. SINGLE TUNNEL CONTINUOUS MOTION WASHER AND DRYER OUTPUT: UP TO 50 BASKETS PER MINUTE DEPENDING ON THE APPLICATION ADJUSTABLE BASKET SIZE ACCOMMODATION AUTOMATIC DRUM FILTRATION STAINLESS STEEL CHAIN CONVEYOR WITH PUSH BARS WASHER LENGTH: 20 FEET DRYER LENGTH: 20 FEET CENTRIFUGAL CIRCULATING PUMPS TOUCHSCREEN CONTROLS ELECTRICAL: VOLTS: 480 FREQUENCY: 60 HZ PHASE 3 STAINLESS STEEL CONSTRUCTION (3) LAARS MIGHTY THERM BOILERS MODEL: B30 HPS