Quarterly Industrial Food and Beverage Processing Equipment Meat and Beverage Processing and Packaging Equipment Auction

AIR PRODUCT CRYO R11-2866-PL QUICK NITROGEN FREEZER TUNNEL WITH: TWO CONTROL PANELS, FOUR SECTIONS, OVERALL DIMENSIONS: LENGTH: 69 FEET, WIDTH: 45 INCHES, HEIGHT: 70 INCHES, ELECTRICAL: 460 VOLTS, 60 HZ, 40 AMPS, PHASE 3

UNIPAK WD-7797 AUTOMATIC BOTTLE DEPALLETIZER S/N: 8000A110 WITH: PALLET SIZE: 44 X 56 (INCHES) HOIST: PALLET STATIONARY W/ LAYER TRANSPORT REMOVING LAYER AND TRANSFERRING TO ACCUMULATION TABLE HEAVY WELDED STEEL LEG STRUCTURE 5 HP BRAKE MOTOR W/ FREQUENCY CONTROLLER AUTOMATIC HEIGHT CONTROL W/ PHOTOEYE FOR LOCATING TOP OF PALLET AUTOMATIC PALLET POSITIONING STOP PUSH BUTTON CONTROL STATION NEMA 12 WIRED CONTROL PANEL CIRCUIT BREAKER FUSED DISCONNECT SWITCH TRANSFORMER ALLEN-BRADLEY (1500) P. L.C. W/ PANEL VIEW 600 PLUS 110" MAX. PALLET LOAD HEIGHT (INCLUDING PALLET) LAYER SWEEP: ON TRAVELING PLATFORM FRONT & REAR SWEEP PUSHER FLIGHT BAR DRIVEN BY SEPARATE 3/4 HP MOTORS SWEEP TRANSFERS OFF THE PALLET AND ONTO ACCUMULATION TABLE LAYER SHEET GRIPPERS: DUAL SET OF CAM ACTIVATED JAW TYPE GRIPPERS GRIPPERS MOUNTED ON REAR STACK ALIGNMENT PUSHER LAYER SHEET STORAGE: AUTOMATIC LAYER SHEET STORAGE IS LOCATED AT THE SIDE OF HOIST ACCUMULATION TABLE: 8' LONG X 4' WIDE (STANDARD BUILT TO SUIT ALL APPLICATIONS) 1 HP MOTOR W/ VARIABLE FREQUENCY CONTROLLER REX SERIES 8505 FLUSH GRID MATT CHAIN OR INTERLOX 900 RAISE RIB TWO SWITCHES ON TABLE HIGH LEVEL TO CONTROL SWEEP CYCLE LOW LEVEL TO CONTROL SINGLE FILLING SINGLE FILER EMPTY PALLET STACKER: HEAVY DUTY SCISSOR LIFT EMPTY PALLET CONVEYOR FROM HOIST TO STACKER INFEED PALLET CONVEYOR: 7' LONG (STANDARD) 1 HP MOTOR W/ VARIABLE SPEED EACH OPERATES INDEPENDENT OF EACH OTHER EACH CONVEYOR HAS PHOTOEYE DETECTION OF PALLET ELECTRICAL: VOLTS: 460 FREQUENCY: 6 HZ PHASE 3

LETINA 525 GALLON STAINLESS STEEL DIMPLE JACKETED TANK APPROXIMATE CAPACITY: 525 GALLONS (2000 LITERS) MAXIMUM ALLOWED WORKING PRESSURE: 2.5 BAR (2) MANWAY OPENINGS: TOP: 12 INCHES SIDE: 16 INCHES (2) SIDE INLETS: 1.5 INCHES (2) DISCHARGE OUTLETS: SIDE DISCHARGE: 2 INCHES OFFSET BOTTOM DISCHARGE: 2 INCHES DISCHARGE HEIGHT FROM GROUND: 5 INCHES DISHED TOP AND BOTTOM MOUNTED ON (4) STAINLESS STEEL LEGS RIGGING HOOKS

INTRALOX 12.5' L ACTIVATED ROLLER BELT LANING CONVEYOR - USED INTERLOX LANING CONVEYOR WITH: OUTPUT: UP TO 500 PRODUCTS PER MINUTE DEPENDING ON PRODUCT AND APPLICATION ACTIVATED ROLLER BELT LENGTH: 12.5 FEET WIDTH: 64 INCHES HEIGHT: 35 INCHES FREE SPINNING ROLLERS: LENGTH: 2 INCHES WIDTH: 0.75 INCHES BI-DIRECTIONAL 3 ZONES (LEFT, MIDDLE, RIGHT) PNEUMATICALLY CONTROLLED ADJUSTABLE SCREW FEET SEW EURODRIVE MOTOR ELECTRICAL: VOLTS: 460 FREQUENCY: 60 HZ PHASE 3 PAINTED STEEL FRAME

LOVESHAW SP304 2 INCH TOP & BOTTOM CASE TAPER - USED LOVESHAW CASE TAPER WITH: TOP & BOTTOM TAPEHEADS: 2 INCH SIDE DRIVE BELTS: HEIGHT: 2 INCHES SPEED: 72 FEET PER MINUTE FLAP FOLDERS CASE CAPACITY: LENGTH: 6 TO 24 INCHES WIDTH: 4.5 TO 20 INCHES HEIGHT: 4.5 TO 24 INCHES ELECTRICAL REQUIREMENTS: VOLTAGE: 110V PHASE: 1 FREQUENCY: 60 HZ CURRENT: 7.6 AMPS MANUALLY ADJUSTABLE HEIGHT AND WIDTH PUSHBUTTON START AND STOP CONTROLS MOUNTED ON ADJUSTABLE HEIGHT LEGS WITH LOCKING SWIVEL CASTERS

DIGITAL SS TABLE TOP SCALE - SS TABLE TOP SCALE: DIGITAL

USED 36" ROTARY ACCUMULATION TABLE WITH: DIAMETER: 36 INCHES STAINLESS STEEL CONSTRUCTION ON CASTERS FIXED SPEED ELECTRICAL REQUIREMENTS: 115 VOLTS, 60 HERTZ, 1 PHASE OVERALL DIMENSIONS: WIDTH: 39.5 INCHES HEIGHT: 40 INCHES

USED 36" ROTARY ACCUMULATION TABLE WITH: DIAMETER: 36 INCHES INFEED HEIGHT: 42 INCHES STAINLESS STEEL TABLE TOP VARIABLE FREQUENCY DRIVE PRODUCT GUIDE RAILS ON CASTERS

CUSTOM INDUSTRIES 4000 PSI POWERWASHER - MI-T-M PRESSURE WASHER WITH: MAX PSI: 4000 WATER FLOW: 3.9 GALLONS PER MINUTE QUICK-CONNECT SPRAY GUN START/STOP PUSH BUTTONS ELECTRICAL: 230 VOLTS, 3 PHASE, 60 HZ

SCA-30/48 BRIDGE SHUTTLE CONVEYOR - USED BRIDGE SHUTTLE CONVEYOR WITH: OVERALL DIMENSIONS: LENGTH:60 INCHES WIDTH: 144 INCHES HEIGHT: 55 INCHES ALLEN BRADLEY CONTROL CIRCUIT TRANSFORMER ELECTRICAL: 220/440-240/480 VOLTS, 50/60-60 HZ SECONDARY VOLTAGE: 110/120 VOLTS

MTC H-LE-S3 COMBO DUMP AND PALLET SEPARATOR WITH: WEIGHT CAPACITY: 3000 POUNDS OVERALL DIMENSIONS: LENGTH: 50 INCHES WIDTH: 50 INCHES HEIGHT: 104 INCHES

200 GALLON AOL200 STAINLESS STEEL SUSPENSION TANK - USED FARM TANK AOL200 TANK WITH: CAPACITY: 200 GALLONS PRODUCTION SPEED: 67 GALLONS PER HOUR MINIMUM CONDENSING CAPACITY: -30 F AT 18,000 BTU AN HOUR AGITATION TYPE: PROPELLER TANK DIMENSIONS: DIAMETER: 42 INCHES DEPTH: 41 INCHES MANWAY DIAMETER: 19 INCHES MOTOR: HP: 0.5 RPM: 950 ELECTRICAL: 95 VOLTS, 5.5 AMPS, 1 PHASE MOUNTED ON PAINTED MILD STYLE FRAME AND CASTERS FOR MOBILITY STAINLESS STEEL CONSTRUCTION

INTEGRITY MACHINE SERVICES FIVE HEAD FOIL SEALER - USED INTEGRITY MACHINE FOIL SEALER WITH: 5 HEAD FOIL APPLICATION UP TO 90 TABS PER MINUTE DEPENDING ON PRODUCT TAB SIZE: 38 MILLIMETER INCLUDES PRODUCT CONVEYOR 4.5 INCH WIDTH 58 INCH LENGTH 42 INCH INFEED/DISCHARGE HEIGHT ELECTRICAL: 240 VOLTS, 60 HZ, PHASE 1

VEMAG STAINLESS STEEL SMOKE GENERATOR WITH: AGITATED HOPPER 32 INCH WIDTH 35 INCH DEPTH STAINLESS STEEL CONSTRUCTION

SOUTHERN CALIFORNIA PACKAGING ST1100 LABELER WITH: SPEED: UP TO 1,100 LINEAR INCHES PER MINUTE WEB WIDTH: 6 INCHES CONVEYOR DIMENSIONS: WIDTH: 6 INCHES LENGTH: 92 INCHES LABEL SIZE: MINIMUM: WIDTH: 0.5 INCHES LENGTH: 0.5 INCHES MAXIMUM: WIDTH: 6 INCHES LENGTH: 18 INCHES CORE DIAMETER: 1 INCH MOUNTED ON CASTERS PUSH-BUTTON CONTROLS WITH DIGITAL READOUT ELECTRICAL REQUIREMENTS: 120 VOLTS, 60 HERTZ, SINGLE PHASE

7.5 INCH WIDE X 58 INCH LONG TABLETOP CONVEYOR - USED TABLETOP CONVEYOR WITH 58 INCH LENGTH 7.5 INCH WIDTH UNIT MOUNTED ON CASTER BASE FRAME

VIDEOJET 37E INKJET CODER - USED VIDEO INKJET 37E INKJET PRINTER WITH: PRINT CAPABILITIES: UP TO 248 CHARACTERS PER SECOND 20 CHARACTER DISPLAY STAINLESS STEEL CABINET CORROSION RESISTANT CABINET STAINLESS STEEL PRINTHEAD SMALL FOOTPRINT QUALITY CODE RESOLUTION

MAURER & SOHNE TWO TRUCK STAINLESS SMOKEHOUSE APPROXIMATE INTERNAL DIMENSIONS: LENGTH: 84 INCHES WIDTH: 44 INCHES HEIGHT: 80 INCHES ZESTI SMOKE LIQUID SMOKE ATOMIZER STAINLESS STEEL CONSTRUCTION WITH TRUCK RAMP

CROWN DMT-40 DIRECT STEAM TILTING KETTLE WITH: CAPACITY: 40 GALLONS STAINLESS STEEL CABINET M.D.M.T. 32 DEGREES FAHRENHEIT AT 35 PSI 316 STAINLESS STEEL LINER 6 INCH ADJUSTABLE HOLD DOWN FEET ONE PIECE COVER 2 INCH TANGENT DRAW OFF VALVE STEAM CONTROL VALVE AND STEAM TRAP SWING DRAIN HOT AND COLD DECK MOUNT FAUCET HYDRAULIC TILT PAN CARRIER VOLTAGE: 115 ELECTRICAL PHASE: 1PH HERTZ: 60HZ

ROBERTS POLYPRO 2149000X HANDLE APPLICATOR WITH: AUTOMATIC, SINGLE LANE HANDLE APPLICATOR PREVIOUSLY USED TO ATTACH PET HANDLES TO 1 GALLON WATER CONTAINERS MORRISON HANDLING SOLUTIONS TIMING SCREW INFEED RIGHT TO LEFT PRODUCT FLOW 4 HEAD ROTARY HANDLE APPLICATOR PUSHES PET HANDLE OVER NECK OF CONTAINER CAN INTEGRATE OVER AN EXISTING CONVEYOR REXROTH TOUCH SCREEN HMI

ENVISIONTEC ULTRA 3SP 3D PRINTER WITH: APPLICATION: UTILIZED 3SP (SCAN, SPIN AND SELECTIVELY PHOTOCURE) TECHNOLOGY TO 3D PRINT PARTS REGARDLESS OF GEOMETRIC COMPLEXITY. SINGLE MATERIAL IS USED FOR BOTH BUILD AND PARTS. SURFACE QUALITY OF THE PRINTED MODELS SHOW NO SIGNS OF STAIRSTEPPING ON THE INNER OR OUTER SURFACES. BUILD ENVELOPE: MAXIMUM VOLUME THE PRINTER CAN PRINT, DETERMINING HOW LARGE OF AN OBJECT THE PRINTER CAN BUILD IS 266 X 175 X 193 MM (10.5 X 6.9 X 7.6 IN.). RESOLUTION IN X & Y (SMALLEST MOVEMENT THAT THE PRINT HEAD CAN MAKE ON A PLANE) IS 100 M (0.004 IN.). DYNAMIC VOXEL RESOLUTION IN Z WHICH IS USER ADJUSTABLE AND MATERIAL DEPENDENT (NUMBER OF SCANS IN THE Z AXIS AND SIZE OF THE LIGHT SHEET TO ACHIEVE HIGHER RESOLUTION) 50 100 M (0.002 0.004 IN.). DATA HANDLING IS IN STL FILES. MATERIALS FOR USE WITH STRETCHED ASSEMBLIES: PSA AND FSA. NEED TO DETERMINE ELECTRICAL REQUIREMENTS FOR THIS UNIT: 100-120V, 8 AMP OR 220-240V, 4 AMP.

LOMA MET30+ METAL DETECTOR DETECTS FERROUS AND NON-FERROUS METALS PIPE DIMENSIONS: LENGTH: 22 INCHES DIAMETER: 2.75 INCHES OVERALL DIMENSIONS: LENGTH: 24 INCHES WIDTH: 24 INCHES HEIGHT: 63 INCHES MOUNTED ON CASTERS EMERGENCY STOP BUTTON ELECTRICAL: 100-240 VOLTS, 50/60 HZ,3 AMPS

AIDLIN DUAL LANE ORIENTER. DUAL LANE FINGER ORIENTATION. CAP SIZE: 4 INCH WIDE X 1 INCH HIGH. PUSH BUTTON START/STOP SWITCHES. MOUNTED ON MILD STEEL FRAME.

PLASTIC MAT TOP 98" DISCHARGE INCLINE CONVEYOR - USED CONVEYOR WITH: INFEED HEIGHT: 39 INCHES PLASTIC MAT TOP BELT WIDTH: 24 INCHES LENGTH: 17 FEET DISCHARGE HEIGHT: 98 INCHES OVERALL HEIGHT: 100 INCHES ELECTRIC MOTOR AND GEAR REDUCER STAINLESS STEEL GUIDE RAILS MOUNTED ON SWIVEL CASTERS

KRAMER GREBE SM325 STAINLESS STEEL BOWL CHOPPER - USED KRAMER GREBE BOWL CHOPPER WITH: BOWL DIAMETER: 60 INCHES CAPACITY: 325 LITERS BIN LIFT SYSTEM 6 BLADE CHOPPING UNIT PRODUCT OUTFEED CHUTE DETACHED ELECTRICAL CONTROL PANEL ELECTRICAL: VOLTS: 380 FREQUENCY: 60 HZ PHASE 3 STAINLESS STEEL CONSTRUCTION

TAYLOR MANUFACTURING 96X60 MASS FLOW ACCUMULATION TABLE - USED ACCUMULATION TABLE WITH: STEEL MESH CONVEYOR INFEED HEIGHT: 43 INCHES CONVEYOR DIMENSIONS: 96 INCHES WIDE X 60 INCHES LONG MOTOR: HORSEPOWER: 37 RPM: 1750 ELECTRICAL: VOLTS: 600 FREQUENCY: 60 HZ PHASE 3

TRUE TSSU-60-24M-B-ST STAINLESS STEEL TABLETOP FREEZER - USED TRUE REACH-IN REFRIGERATOR WITH: HELD TEMPERATURE RANGE: BETWEEN 33 F AND 41 F REMOVABLE POLYETHYLENE CUTTING BOARD DIMENSIONS: WIDTH: 60.375 INCHES DEPTH: 8.875 INCHES HEIGHT: 0.5 INCHES SHELVES (4): CONSTRUCTION: PVC COATED WIRE DIMENSIONS: WIDTH: 27.5 INCHES DEPTH: 16 INCHES EPOXY COATED EVAPORATOR STAINLESS STEEL FOAM INSULATED LIDS (2) OVERALL DIMENSIONS: WIDTH: 60.375 INCHES DEPTH: 34.125 INCHES HEIGHT: 40.375 INCHES ALUMINUM BACK CONSTRUCTION STAINLESS STEEL FRONT AND SIDE EXTERIOR SURFACES MOTOR: 0.33 HORSEPOWER ELECTRICAL: 1 PHASE, 60 HZ, 115 VOLTS

SCHROETER SMOKE GENERATOR WITH: AGITATED HOPPER DIAMETER: 24 INCHES DEPTH: 22 INCHES STAINLESS STEEL CONSTRUCTION

SCHROETER SMOKE GENERATOR WITH: AGITATED HOPPER DIAMETER: 24 INCHES DEPTH: 22 INCHES STAINLESS STEEL CONSTRUCTION

USED SMOKE GENERATOR WITH: AGITATED HOPPER 16 INCH WIDTH 12 INCH LENGTH 24 INCH DEPTH STAINLESS STEEL CONSTRUCTION

VEMAG SMOKE GENERATOR: TOP LOAD AGITATED HOPPER DIAMETER: 32 INCHES DEPTH: 23 INCHES SIDE MOUNTED EXHAUST STAINLESS STEEL CONSTRUCTION

UNIVERSAL TA4 WRAP UNIT PRESSURE SENSITIVE LABELER WITH: SPEED: UP TO 3000 INCHES PER MINUTE (DEPENDING ON PRODUCT SPECIFICATIONS) FILM CORE: 3 INCHES MAXIMUM FILM WIDTH: 6 INCHES GRIPPER BELT HEIGHT: 4 INCHES CONVEYOR DIMENSIONS: LENGTH: 120 INCHES WIDTH: 6 INCHES ANALOG DIAL CONTROLS MOUNTED ON CASTERS ELECTRICAL: 115 VOLTS, SINGLE PHASE, 60 HZ

HYDRAULIC PUMP AND RESERVOIR WITH: LEVEL INDICATOR SIGHT GLASS VENTED RESERVOIR ELECTRICAL REQUIREMENTS: 203/460 VOLTS, 52/26 AMPS

HYDRAULIC PUMP AND RESERVOIR WITH: LEVEL INDICATOR SIGHT GLASS VENTED RESERVOIR ELECTRICAL REQUIREMENTS: 203/460 VOLTS, 52/26 AMPS

CLEATED INCLINE CONVEYOR 82 INCH DISCHARGE - USED INCLINED CONVEYOR WITH: CLEATED BELT: BELT WIDTH: 24 INCHES CLEAT CENTERS: 30 INCHES CLEAT WIDTH: VARYING APPROXIMATE LENGTH: 160 INCHES DISCHARGE HEIGHT: 82 INCHES OVERALL HEIGHT: 86 INCHES PRODUCT GUIDE RAILS ELECTRIC MOTOR AND GEAR REDUCER PUSH BUTTON CONTROLS WITH EMERGENCY STOP BUTTON

VEMAG STAINLESS STEEL SMOKE GENERATOR WITH: AGITATED HOPPER 35 INCH WIDTH 32 INCH DEPTH STAINLESS STEEL CONSTRUCTION

2019 STEINCRAFT BBTD-30 30 BBL STAINLESS STEEL JACKETED BRITE TANK. CAPACITY: 30 BBL. PRESURE RATING: 2 BAR / 29 PSI. ELLIPTICAL MANWAY: WIDTH: 17 INCHES HEIGHT: 14 INCHES. VARIOUS 2 INCH INLETS AND OUTLETS. CONICAL BOTTOM WITH 90 FLANGED DISCHARGE. STAINLESS STEEL CONSTRUCTION. MOUNDED ON (4) LEGS.

USED ROTATING FILLER FRAME WITH: NOZZLE DIAMETER: 3/4 INCHES STATION DIMENSIONS: LENGTH: 6.5 INCHES WIDTH: 3.25 INCHES (24) STATIONS TOUCHSCREEN HMI ELECTRICAL REQUIREMENTS: 130 VOLTS, 60 HERTZ, 1 PHASE OVERALL DIMENSIONS: LENGTH: 39 INCHES WIDTH: 50 INCHES HEIGHT: 75 INCHES

E-PAK 40 DIAMETER STAINLESS STEEL ACCUMULATION TABLE WITH: DIAMETER: 40 INCHES INFEED DIMENSIONS: WIDTH: 33 INCHES HEIGHT: 45 INCHES GUIDE RAIL DIMENSIONS: HEIGHT: ADJUSTABLE THICKNESS: 0.5 INCHES VARIABLE SPEED CONTROL MOTOR: HORSEPOWER: 0.25 RPM: 1750 MOUNTED ON SCREW LEVELING LEGS STAINLESS STEEL CONSTRUCTION

WORLD CUP 8 12 STAINLESS STEEL ROTARY CUP FILLER - USED WORLD CUP FILLER WITH: OUTPUT: UP TO 45 CUPS PER MINUTE NUMBER OF STATIONS: 8 CONTAINER SIZE RANGE: 1 - 10 OUNCES MAXIMUM DIAMETER: 3.18 INCHES SINGLE HEAD PISTON FILLER: HOPPER CAPACITY: 5 GALLONS PISTON CYLINDER (INCHES): 8.5 LONG X 2.25 DIAMETER HOPPER DIMENSIONS (INCHES): 20 DIAMETER X 22 DEEP TAMPER EVIDENT PRE-CUT FOIL HEAT SEAL WASH-DOWN UNIT STAINLESS STEEL AND ANODIZED ALUMINUM CONSTRUCTION

VLS TECHONOLOGIES FVV 35 VERTICAL PLATE FILTER - USED STAINLESS STEEL JET WASHING MACHINE WITH: TUB DIMENSIONS: LENGTH: 23 INCHES WIDTH: 54 INCHES DEPTH: 15 INCHES 18 JETS STAINLESS STEEL DEBRIS FILTER OZONE BUBBLE CAPABLE DIGITAL TEMPERATURE READOUT HEATING ELEMENT SWITCH OZONE SWITCH BUBBLE WASH SWITCH 1.5 INCH THREADED OUTLET STAINLESS STEEL CONSTRUCTION

CRATE OF MISCELLANEOUS SMOKE GENERATOR PARTS: 6 STAINLESS STEEL BUCKETS: DIAMETER: 12 INCHES DEPTH 12 INCHES 4 STAINLESS STEEL TRAYS (2) TRAYS: LENGTH: 18 INCHES WIDTH: 6 INCHES DEPTH: 7 INCHES (2) TRAYS: LENGTH: 12 INCHES WIDTH: 6 INCHES DEPTH: 12 INCHES

SMOKE GENERATOR STAINLESS STEEL - SMOKE GENERATOR: AGITATED HOPPER DIAMETER: 28 INCHES DEPTH: 28 INCHES SIDE MOUNTED EXHAUST STAINLESS STEEL CONSTRUCTION

2015 KENT GW STAINLESS STEEL JACKETED BRITE TANK - USED GW KENT TANK WITH: CAPACITY: 20 BBL PRESURE RATING: 15 PSI ELLIPTICAL MANWAY: WIDTH: 17 INCHES HEIGHT: 14 INCHES VARIOUS 2 INCH INLETS AND OUTLETS CONICAL BOTTOM WITH 90 FLANGED DISCHARGE STAINLESS STEEL CONSTRUCTION MOUNDED ON (4) LEGS

USED SMOKE GENERATOR WITH: DIMENSIONS LENGTH: 36 INCHES WIDTH: 28 INCHES HEIGHT: 60 INCHES HINGED DOOR ACCESS STAINLESS STEEL CONSTRUCTION

HEUFT SPECTRUM TX PRODUCT INSPECTION - USED PEARSON MP35 MULTI-PACKER WITH: OUTPUT: UP TO 30 CASES PER MINUTE IN-LINE INFEED: (6) 4 PACK CARRIER BASKETS (4) 6 PACK CARRIER BASKETS (3) 8 PACK CARRIER BASKETS CROSS FLOW INFEED: (4) 6 PACK CARRIER BASKETS CARRIER SIZES: LENGTH: 6.75-11.75 INCHES WIDTH: 4.75-5.5 INCHES DEPTH: 2.5-5.75 INCHES CASE SIZES: LENGTH: 10-21 INCHES WIDTH: 10-17 INCHES HEIGHT: 4-10 INCHES DUAL LANE BRUSH DRIVE INFEED: LENGTH: 140 INCHES WIDTH: 7.5 INCHES EACH LANE CASE INFEED: LENGTH: 73 INCHES WIDTH: 10 INCHES 90 DEGREE CASE DISCHARGE: LENGTH: 74 INCHES WIDTH: 10 INCHES PRODUCT RAM CASE STOP ALLEN BRADLEY HMI AIR REQUIREMENTS: 80 PSI ELECTRICAL REQUIREMENTS: 460 VOLT, 60 HZ, 3 PH

DIVERSIFIED STEAM CAPPER WITH: CONTAINER CONVEYOR (MISSING BELT): LENGTH: 105 INCHES WIDTH: 4 INCHES INFEED/DISCHARGE HEIGHT: 35 INCHES RESINA STYLE CAP SORTER: 32 INCH DIAMETER CAP HOPPER: LENGTH: 30 INCHES WIDTH: 30 INCHES DEPTH: 20 INCHES PUSH BUTTON CONTROLS WASHDOWN IDC MOTOR ELECTRICAL: VOLTS: 460 FREQUENCY: 60 HZ PHASE 3

SKA SNODGRASS MAGICBUS RE PALLETIZER GLASS BOTTLES WITH: THE INTENDED USE OF THE FAR BULK PALLETIZER IS TO MOVE EMPTY CANS FROM THE OUTFEED OF A MACHINE SUCH AS A SLEEVER, LABELER OR PRINTER ONTO STANDARD 44 INCH BY 56 INCH STORAGE PALLETS. THE FAR WILL PLACE THE CANS IN SUPERPOSED LAYERS SEPARATED BY A TIER SHEET. INFEED HEIGHT FROM GROUND: 25 INCHES LIFTING CAPACITY: 300 POUNDS CAPABLE OF RUNNING: 211: 8 OZ/12 OZ/16 OZ/19.2 OZ 389 STANDARD CANS/LAYER 204: 2 OZ SLEEK 506 STANDARD CANS/LAYER 207.5: 12 OZ SLEEK 472 STANDARD CANS/LAYER 307: 32 OZ CROWLER 240 STANDARD CANS/LAYER 202: 187 ML/250 ML 586 STANDARD CANS/LAYER CAN SIZE: MAXIMUM LAYER COUNT: 202: 18 LAYERS 204: 16 LAYERS 207.5: 17 LAYERS 211: 21 LAYERS 211: 16 LAYERS 211: 13 LAYERS 307: 13 LAYERS

HOBART 4356 MIXER GRINDER WITH: PRODUCTION RATE: UP TO 160 POUNDS PER MINUTE CAPACITY: 500 POUNDS OVERALL DIMENSIONS: LENGTH: APPROXIMATELY 72 INCHES WIDTH: APPROXIMATELY 41 INCHES HEIGHT: APPROXIMATELY 96 INCHES STAINLESS STEEL CONSTRUCTION 0.5 HORSEPOWER MOTOR ELECTRICAL: 208-230/460 VOLTS, 60 HZ, PHASE 3

MEHEEN 6 HEAD FILLER/CROWNER 6 HEAD FILLER/CROWNER SPEEDS: UP TO 36 BOTTLES PER MINUTE:DEPENDING ON APPLICATIONS AND SIZES RINSE RACK HOPPER DELIVERS CROWNS TO CROWNER BAR FOR FULLY AUTOMATED INDEXING AND CRIMPING COUNTER PRESSURE FILLING WITH CO2 PRE-PURGE TOUCH SCREEN CONTROLS ELECTRICAL: 115/240 FREQUENCY: 60 HZ PHASE 3 REQUIRED AIR: 40 PSI CURRENT SET UP: 22 OUNCE GLASS BOTTLES