SIPORT 3 METAL IND LTD CLOSEOUT AUCTION

24 IN. VERNIER CALIPER

18 IN. VERNIER CALIPER

2 EVINRUDE O/B MOTORS, TANK, STAND

15 HP 208-220/440 ELEC. MOTOR

DEPTH GAUGE SET

WOOD SPINNING LATHE DIES

DIE

HYD. PALLET JACK

JET FLOOR DRILL PRESS

ENGINE STAND (ON MEZZANINE)

LOT OF ASSORTED METAL FENCING PANELS

HYDRAULIC PUMP (ORIGINALLY ON 600T PRESS)

1 TON ARBOR PRESS

LOT OF MISC. PARTS ETC.

RIDGID MOD. 14 IN. CHOP SAW

MOBILE 33 IN. X 45 IN. WHITEBOARD

POWER FIST POWDER COATING SYSTEM

18' EXTENTION LADDER

REMA 1 TON CHAIN HOIST

POWERFIST 2 TON CHAIN HOIST

MERCRUISER STERN DRIVE LEG

MACHINE VISE

LIFTING SLINGS

POWERFIST 2 TON CHAIN HOIST

POWERFIST 2 TON CHAIN HOIST

DIE FOR LIGHT FIXTURE BUCKET

PAINT SPRAY GUN KIT

FRIDGIDAIRE 2 DOOR FRIDGE (IN MEZZANINE)

POWERFIST 2 TON CHAIN HOIST

MAKITA POWER HAND SAW

ASSORTED CHAIN W/HOOKS

MAXIM 2006 2600SE 26 FT. CUDDY CABIN BOAT WITH TRAILER S/N POYR 2956, 29 FT. OVERALL LENGTH WITH SWIM PLATFORM WITH LADDER, PRISTINE CONDITION CANVAS TOP/COVER, GOOD UPHOLSTERY, GALLEY WITH MICROWAVE, SINK, REFRIGERATOR AND COOKTOP, DINETTE/FORWARD BERTH AND SEPERATE MIDCABIN BERTH - SLEEPS 4. ENGINE: METER READS 313.6 HRS., MERCRUISER 5.0L/260HP WITH BRAVO III STERNDRIVE, BOTTOM IS CLEAN. TRAILER: CALKINS 26 FT. T/A WITH NEW BALL HITCH COMPONENT IN ALL AROUND GOOD CONDITION.

PRESS DIE FOR 24 IN. TANK END W/WOOD LATHE CAP TRIM DIE

PRESS DIE FOR 20 IN. TANK END

PRESS DIE FOR 18 IN. TANK END W/WOOD LATHE CAP TRIM DIE

2019 SI 600T 600 TON 4 POST HYDRAULIC DEEP DRAW PRESS: CUSTOM MADE BY SI-PORT WITH COMPONENT COST OF $115,000 IN 2019. PRESS FEATURES 39 IN. X 51 IN. ID BED, APPROX. 8 FT. DAYLIGHT OPENING, FOOTPRINT - 124 IN. (ADD 12 IN. FOR SMALL STEP) X 172 IN. X 259 IN. HIGH, TOP MAIN CYLINDER 26 IN. DIA. AMADA BRAND AND 20 IN. DIA. BOTTOM CYLINDER AMADA BRAND, POSTS - 4 AMADA BRAND 8.5 IN. DIA., 2 HYDRAULIC OIL TANKS WITH 2500L CAPACITY TOTAL, 6 IN. HYD. OIL SERVICE PIPING, P/W 50HP/ 600V/3PH HYDRAULIC PUMP, ABB SOFTSTART, WESTINGHOUSE BREAKER BOX. SPARE PARTS SOLD SEPARATE - 75HP/600V MOTOR AND HYDRAULIC PUMP, HYDRAULIC PUMP ONLY (WAS SERVICING A 150HP MOTOR). THIS PRESS WAS USED TO SERVICE A CONTRACT FOR INDUSTRIAL WATER HEATER END CAPS WHICH EARNED A $75,000 NET PROFIT. THIS CONTRACT MAY STILL BE CARRIED ON BY A NEW SUPPLIER UPON NEGOTIATION WITH INFORMATION SUPPLIED BY THE RETIRING OWNER OF SI-PORT 3 TO THE BUYER OF THE 600 TON PRESS. 4 DIES OWNED BY SI-PORT 3 FOR THE END CAPS ARE TO BE SOLD SEPARATE FOLLOWING THE SALE OF THE PRESS. THIS PRESS COMES APART IN THREE BASIC SECTIONS FOR DISMANTLING.

MOBILE 5 FT. L DESK TABLE