Nutra Packaging Surplus Equipment

RESINA SCREW CAPPER U40 282 MODEL: U40 282 SN: 67 3884

PHARMA PACK CLEATED CAP ELEVATOR BELT WIDTH: 10" HEIGHT: 9FT

PHARMA PACK CLEATED CAP ELEVATOR BELT WIDTH: 10" HEIGHT: 9FT

PHARMA PACK CLEATED CAP ELEVATOR BELT WIDTH: 10" HEIGHT: 9FT

PHARMA PACK PUMP CAPPER PCT-2008 - 1- PHARMA PACK PUMP CAPPER PCT-2008 MODEL: PCT-2008 VOLTAGE: 480 FREQUENCY: 60HZ POWER: 4.21KW AIR CONSUMPTION: 0.5-0.7MPA 280L/MIN S/N: 1502041

ROSER DOUBLE BOTTOM FED LABELER - 1- ROSER DOUBLE BOTTOM FED LABELER

PACE BOTTLE ORIENTER M409 - 1- PACE BOTTLE ORIENTER M409 MODEL: M409 SN: 864

INTERPACK CASE TAPER HSD 2000 - INTERPACK CASE TAPER HSD 2000 S/N: H 175 17J 357

2024 IPG INTERPACK CASE TAPER USA2024-BB MODEL: USA2024-BB SN: TM 094 16 D 023 HP: 2X 1/3HP VOLTAGE: 115 FREQUENCY: 60 HZ PHASE: 1 AMPS: 6

ROSER PRODUCTS INC BOTTOM FED LABELER

ACCRAPLY DOUBLE SIDED LABELER 35PW MODEL: 35PW VOLTAGE: 230 FLA: 12 PHASE: 1 PSI: 80 HZ: 60 BELT WIDTH: 4 1/2" S/N: 4026

2006 ACCRAPLY DOUBLE SIDED LABELER 350 PW S MODEL 350 PW S VOLTS: 220 PHASE: 1 FREQUENCY: 60 HZ S/N: 5210

[TES 150] BOTTLE UNSCRAMBLER APPROXIMATE BOTTLE RANGE: 50CC~400CC MAX CAPACITY: 150 BOTTLES / MIN POWER REQUIREMENTS: 208~220VAC ; .5KW DIMENSIONS: 59.25 X 36 X 45.75 NET WEIGHT: 770 LBS AIR PRESSURE: 75 PSI AIR CONSUMPTION: 3 CFM FEED HEIGHT: 31 -34.5 (1) PHARMAFILL TC3 DEITZ COUNTER MODEL: TC3 SERIAL NUMBER: 1103 TYPE: AD1115 REVB VOLTS: 110 HZ: 60 AMPS: 6 AUTOMATED TC3 ELECTRONIC TABLET COUNTER SOLID ORAL DOSE SPECIFICATIONS MAXIMUM WIDTH OR DIAMETER: 0.9 INCH (22 MM) MAXIMUM LENGTH: 0.9 INCH (22 MM) MAXIMUM HEIGHT: 0.4 INCH (10 MM) MAXIMUM COUNTING RATE: 2500-3000 PER MINUTE TABLET TYPE: TYPICAL COATED TABLET, DIAMETER .25 INCH CAPSULE SIZE: TYPICAL CAPSULE, SIZE 00 MAXIMUM FILLING RATE 50-60 BOTTLE PER MINUTE ACCURACY TYPICALLY 99.99% (1 ERROR PER 10,000 PILLS) AT OPTIMAL CONDITIONS FILLS BOTTLES UP TO 10 IN HEIGHT (1) 16' PHARMAFIL CONVEYOR (1) PHARMAFILL TC3 DEITZ COUNTER MODEL: TC3 SERIAL NUMBER: 1073 TYPE: AD1115 REVB VOLTS: 110 HZ: 60 AMPS: 6 (1) EIA METAL DETECTOR SYSTEM MODEL: THS SERIAL NUMBER: 21000225005 APERTURE: 10" X 8" (1) KAPS ALL E4 CAPPER WITH HOPPER MODEL: E4 SERIAL NUMBER: 4589 (1) PHARMAFILL CONVEYOR CV4 5'X 288'' MODEL: CV4 SERIAL NUMBER: 1410 TYPE: AD0959-288 REV A VOLTS: 115 HZ: 60 AMPS: 5 (1) PHARMAFILL CONVEYOR CV4 5'X 288'' MODEL: CV4 SERIAL NUMBER: 1410 TYPE: AD0959-288 REV A VOLTS: 115 HZ: 60 AMPS: 5 (1) PHARMAFIL NB1 NECK BANDER MODEL: NB1 SERIAL NUMBER: 028 TYPE: AD1178 REV A VOLTS: 110 HZ: 60 AMPS: 3 (1) PILLAR UNIFOILER U2P1002000000 MODEL: U2P1002000000 PART NUMBER: CB93101 VOLTS: 208/240 AMPS: 15/13 HZ: 50/60 PHASE: 1 (1) CVC 300 C WRAP LABELER MODEL: 300 C SERIAL NUMBER: 10701080 VOLTS: 110 HZ: 60 PH: 1 (1) PHARMAFIL A36 ACCUMULATION TABLE 36" DIAMETER SERIAL NUMBER: 1187 TYPE: AD0924-4 VOLTS: 115 HZ: 60

2023 CVC 1112H DESICCANT BARREL INSERTER TYPE: U4 VOLTAGE: 220 / 450VA AMPERAGE: 2.1 FREQUENCY: 60 HZ AIR CONSUMPTION: 361 NL/MIN AIR PRESSURE: 87 PSI WEIGHT: 220KG S/N: 11203027

2024 CVC 2.5 CONVEYOR W/ DIVERTER MODEL: 2.5 CONVEYOR SERIAL NUMBER: 11203040 VOLTS: 190/220 HERTZ: 50/60 AMPS: 0.9 PHASE: 1 AIR PRESSURE: 87 PSI MANUFACTURE DATE: 2024 DIMENSIONS: 8.2' X 4.5"

FORTRESS METAL DETECTOR WITH REJECTION STATION OPENING OF METAL CHECK 6" X 7" CONVEYOR ON METAL CHECK 4' X 4.5" WIDE REJECT: 250VAC ISOLATED: 250 VAC FAULT: 250VAC S/N: CD30768

2007 PILLAR UNIFOILER U2P1742000002 IS A PILLAR UNIFOILER U2P1742000002. MODEL: UNIFOILER U2P1742000002 ORDER #: 62347-1 MANUFACTURE DATE: 2007 PART NUMBER: CB10093160 VOLTS: 208/ 230 AMPS: 15/13 HERTZ: 60 PHASE: 1

2010 PALACE PACKAGING MACHINE SCOOP INSERTER CB-42-SF & H-15 WITH SCOOP ELEVATOR MODEL: CB-42-SF& H-15 PR 114-002 // RC-6-14 FEATURES SCOOP ELEVATOR AIR PRESSURE: 60 VOLTAGE: 120 CURRENT: 20 POWER: 2400W PHASE: 1 HERTZ: 60 SN: 8741

2017 PALLAY PACK PHARMA PACKAGING SYSTEM PPS906 PHARMA COUNT 2-2R3 VOLTAGE: 110 PHASE: 1 HZ: 60

2008 PHASE FIRE 33-0A0-013 SHRINK TUNNEL - 1- PHASE FIRE SHRINK TUNNEL VOLTS: 220 AMPS: 30 KW: 12 PHASE 3 APERTURE: 14 S/N: A-17L07-2026

PHASE FIRE SHRINK TUNNEL - 1- PHASE FIRE SHRINK TUNNEL MODEL: 33-0A0-013 VOLTAGE: 220 AMPS: 30 KW: 12 PHASE:3 APERTURE: 14 S/N: A-17L07-2027

APPS COUNTER 16 LANE MODEL: R-16K TABLET COUNTER VOLTAGE: 120 AMPS: 15 FREQUENCY: 60 HZ AIR: 80 PSI @ 1 CFM FEATURES: DUAL EIGHT-LANE COUNTING SYSTEMS LARGE 3600 CUBIC-INCH CAPACITY HOPPER AUTOMATIC FEED CONTROL STAINLESS STEEL CONSTRUCTION

[2005] ATLAS COPCO GA180VSD-FF ONBOARD AIR COMPRESSOR (GA180VSD) SPECS MODEL: GA180VSD SN: AIF.104549 MAX WORKING PRESSURE: 13.55(BAR) MAX WORKING PRESSURE: 196 (PSI) INPUT POWER: 183 KW HP 245 RPM 3085 DIMENSIONS: 11'X6'X80

2006 SUN JIN SM AUTO LABELLER M/C SJC-3217 MODEL: SJC-3217 SERIAL NUMBER: SJC3217-200604 VOLTS: 110 PHASE: 1 HERTZ: 50/60 DIMENSIONS: 81X50X77 PRODUCT INFORMATION: LABELING HEIGHT AND ANGLE ARE ADJUSTABLE. THE WRAP STAIN MAKES LABELS ADHERE WELL. THE CONVEYOR BELT AND LABELING SPEED ARE ADJUSTABLE. ADVANCED SENSOR DETECTION SYSTEMS ENSURE LABELING QUALITY. THE MACHINE IS CONTROLLED BY A MICROPROCESSOR SYSTEM WITH AN LED SCREEN, WHICH IS EASY TO READ AND SET INFORMATION.

1998 BOSCH KKE 1500 TABLET INSPECTION SYSTEM - 1- BOSCH KKE 1500 TABLET INSPECTION SYSTEM MFG: 1998 MACHINE NUMBER: 782622 VOLTAGE: 250 AMPERAGE: 30 TOOLING SETS INCLUDED SIZE 0 SIZE 00 SIZE 000 TWO SETS OF SIZE 2 TOOLING SIZE 3 SIZE AA SIZE B DESCRIPTION: BOSCH MODEL KKE1500 WITH BOB CAPSULE CHECKWEIGHER. CAPABLE OF HANDLING HARD GELATIN CAPSULES IN SIZES FROM 00, 0, 1-4 SIZE RANGES. S/N: 782622

2021 SHV PACKING MACHINE MODEL NUMBER SHV-CL 220 V 50 HZ PRODUCT NUMBER: YZ 0125

CAP ELEVATOR VARIABLE SPEED CONTROL 220 V

[2021] SUNNY GROUP 12 HEAD DUAL LANE LIQUID FILLER - 12 HEAD DUAL LANE LIQUID FILLER TWO LANES OF SIX FILLING HEADS TO FILL SIX BOTTLES ON EACH SIDE AT A TIME CAPACITY: 1800-3600 BOTTLES AN HOUR WORKING ENVIRONMENT TEMPERATURE: 5C - 50C PRODUCT DESCRIPTION: DUAL LANE LIQUID FILLER 6 HEADS IN EACH LANE FILLING ACCURACY CAN BE CONTROLLED UP TO 1%.

2021 SUNY GROUP WET WIPES CANISTER SEALING MACHINE MODEL NUMBER: SYC2 CAPACITY: 1500- 2400 BOTTLES AN HOUR VOLTAGE: 220 HERTZ: 50

PRESS CAP MACHINE WITH 6 SPINDLE RETORQUER MULTIPLE SIZES OF CAP SCHUTES 4 DIAMETER 4 3/8 DIAMETER 5 1/4 DIAMETER 4 3/8 DIAMETER 5 3/8 DIAMETER PRODUCT DESCRIPTION: THE AUTOMATIC MANDREL CAPPING MACHINE IS A CONTINUOUS UNIVERSAL CAPPING MACHINE DESIGNED WITH CONTEMPORARY ADVANCED SCIENCE AND TECHNOLOGY. IT IS SUITABLE FOR ROUND SCREW CAPS AND ROUND CAPS WITH NOZZLES. SPECIFICATIONS: THREAD CAP DIAMETER: 0-100MM BOTTLE DIAMETER: 0-180MM BOTTLE HEIGHT: 0-400MM PRODUCTION CAPACITY: 40-150 BOTTLE/MIN VOLTS: 220 HERTZ: 50 OVERALL DIMENSIONS: 46"L X 36"W X 64"H

EASTY CASE PACKER 1630 - 1 - EASTY CASE PACKER 1630 VOLTS: 120 AMPS: 4.1 PHASE 1 OVERALL DIMENSIONS: 74"L X 36"W X 49"H

[2000] TRANSFER CONVEYOR WITH BOX STRAPPER PLATFORM: 30 X 43 CONVEYOR: 28 1/2" OVERALL DIMENSIONS: LENGTH IS 75"L X 33"W X 62"H VOLTS: 220

AESUS DELTA STARCAP MODEL: DELTACAP 1 VOLTSAC: 208 HERTZ: 60 PHASE: 1 AMPS: 15 PSI: 80 SCFM: 46 PRODUCT FEATURES: AUTOMATIC PUSH THROUGH 2 STATION CAPPER (1 PRE-SPIN STATION, 1 FINAL TORQUING STATION) WITH AN INDEXING STARWHEEL. SERVO DRIVEN CAPPING AND TORQUING STATIONS PNEUMATIC UP/DOWN SLIDE TABLES FOR CAPPING APPLICATION FULLY GUARDED FRAME ENCLOSED FRAME MOTORIZED UP/DOWN FOR CHANGE OVERS PLC CONTROLLED WITH COLOR TOUCHSCREEN (STANDARD) BOTTLE RANGE FROM 3/4 TO 8 DIAMETER AND 1 TO 12 TALL CAP RANGE FROM 34 TO 5 DIAMETER *INCLUDES INTERCHANGABLE STAR WHEELS AND CAP TORQUER HEADS. S/N: 397700112

YUNG SUN TOP AND BOTTOM AUTOMATIC BOX TAPE MACHINE FJ-1A - 1- YUNG SUN TOP AND BOTTOM AUTOMATIC BOX TAPE MACHINE MODEL: FJ-1A POWER SUPPLY: 110V/220V 50/60 HZ 600W SEALING SPEED: 20 METERS/MIN CARTON SIZE: L(150-)W(120-480)H(120-480)MM TAPE SIZE: 48-72MM(KRAFT OR BOPP TAPE) MACHINE SIZE: L(1090)W(890)H(1280)MM SHIPPING SIZE: L(1200)W(1050)H(1435)MM G.W/N.W: 250KG/200KG 2-3" TAPE WIDTH: 1000 YARD LENGTH

CVC BUCKET ELEVATOR - 1- CVC BUCKET ELEVATOR MODEL: CVC1101

1994 ROVEMA VPRS250 VERTICAL FORM & FILL SEAL TYPE: VPRS250 MACHINE NO: 12124 SERIES: 3/5 YEAR: 1994 POWER SUPPLY: 460 VAC 3-PH 20 A WEIGHT RANGE: 50 - 1000G BAG SIZE RANGE: 4"-19-11/16" L; 2-3/8"-9-13/16" W COMBINATION SCALE: EQUIPPED WITH A STAINLESS STEEL VIBRATORY FEEDER, FOURTEEN 240 IN3 STAINLESS STEEL BUCKETS, AND MICROPROSESSOR CONTROLS. CONTINUOUS MOTION, 14 HEAD COMBINATION SCALE AND VERTICAL FORM FILL & SEAL MACHINE RATED UP TO 120 BAGS PER MINUTE DEPENDING ON MATERIALS AND APPLICATION. FORM FILL AND SEAL: EQUIPPED WITH FILM REGISTRATION, SERVO CONTROLLED FILM TRACKING, DUAL SIDE BELT FILM ASSIST, 10" LONG LAP SEAL, 11" WIDE CROSS SEAL, A/B PLC, INTERLOCKING LEXAN SAFETY GUARDING, AND A TOUCH PAD CONTROLLER. FILM SPECIFICATIONS: UP TO 21" WIDTH; UP TO 24" IN DIAMETER; 3" CORE. S/N: 12124

3M-MATIC CASE TAPER ADJUSTABLE CASE SEALER TYPE 19200 MODEL: 800A3 VOLTS: 115 HZ: 60 AMPS: 2.8 WATTS: 315 S/N: 1794

SPECK-TECH BOTTLE UNSCRAMBLER B-10 - 1 - SPECK-TECH BOTTLE ELEVATOR B-10 MODEL: B-10 WEIGHT: 405.5 LBS DIMENSIONS: 128"L X 44"W X 84"H MADE IN CANADA

2018 BALPACK CEISB CAPPER 1- BALPACK W/ CAP ELEVATOR & CONVEYOR CAP SIZE: 89MM VOLTAGE: 120V AC MFR DATE: 8/2/2018 CONVEYOR SIZE: 4''WIDE X 144'' LONG DIMENSIONS: 70''W X 144''L X 95'' 80 PSI FULLY AUTOMATIC 2 STATION INLINE CHUCK CAPPER: FOR INCREASED CAPPING SPEEDS UP TO 100BPM ON CAPS UP TO 63MM INCLUDES DEDICATED BOTTLE FEEDSCREW DRIVE SYSTEM STAINLESS STEEL AND ANODIZED ALUMINUM CONSTRUCTION. LARGE CAPACITY CAP SORTING ELEVATORS WITH 12, 15 AND 18 CHAIN OPTIONS. SERVO CONTROLLED 1ST STATION CAP PLACING SYSTEM WITH INTEGRATED VACUUM PICK UP FOR HOLDING CAP WHILE PLACING ON CONTAINER. SERVO CONTROLLED 2ND STATION TORQUING CHUCK, FOR HIGHLY ACCURATE AND REPEATABLE FINAL TORQUE S/N: 32890-1

QUADREL LABELING SYSTEMS EV 074 MODEL: 060 SERIAL NUMBER: 0603022 VOLTS: 110 PHASE: 1 AMPS: 12 DOM: 11.03.05

[1996] R. A. JONES PK-4000 POUCH / SACHET FILLING MACHINE WITH CTC SPLICER AND KNIFE CUTOFF STATION MODEL: PKH 4000 SERIAL NUMBER: S-5296 SPEED: 4000-5000 INCHES PER MIN, 1600 POUCHES PER MIN AT 3" CUTOFF AT 5000 MATERIALS: 1.5 TO 5 MIL, INCLUDING RETORTABLE AND ORIENTED POLY PROPYLENE SIZE RANGE: WIDTH AND LENGTH CAN BE CHANGED DEPENDING ON THE TUCKING MECHANISM OF THE MACHINE MAX WEB WIDTH: 24" MFG. DATE: OCTOBER 28, 1996 VOLTS: 240 HZ: 60 PHASE: 3. ALSO INCLUDES USED EV 037 ECCENTRIC LAP SLICER / CRIMPER MACHINE WITH PICK IN PLACE MODEL: HD-ALRS-900M SERIAL NUMBER: VOLTS: 115 HZ: 50/60 PHASE: 0 AMPS: 9 PRESSURE: 80PSI QUALITY: CLEAN NONLUBRICATED. DRY TO DEW POINT OF 40 DEGREES. THIS MACHINE IS TOOLED AND SET TO RUN A PACKET THAT IS 3'1/4'' LENGTH X 2''1/4'' WIDE CTC SPLICER THE CTC SPLICER UNIT DISPENSES WEB MATERIAL TO CREATE THE POUCHES, AND FEATURES AUTOMATIC SPLICING TO PROVIDE A CONTINUOUS SUPPLY OF WEB STOCK. EDGE GUIDE SYSTEM THE POSITION OF THE EDGE OF THE WEB WILL WILL VARY SLIGHTLY AS THE WEB UNWINDS. THE WEB PASSES BETWEEN THE EDGE OF THE GUIDE SENSORS WHICH MONITOR THE POSITION OF THE WEB. THE CORRECTION ROLLER SWIVELS TO KEEP THE WEB ALIGNED WITH THE PLOW. PLOW THE WEB IS HORIZONTALLY OVER THE PLOW, FORMING A LENGTHWISE FOLD NEAR THE CENTERLINE OF THE WEB. THE WEB IS FOLDED SLIGHT OFF- CENTER TO LEAVE A SMALL LIP USED TO OPEN POUCHES. THE FOLDED WEB IS VERTICAL AS IT LEAVES THE PLOW AND PASSES BETWEEN THE FORMER BLADES TO COMPLETE THE FOLD. THE WEB THEN PASSES THROUGH THE CREASING ROLLER ASSEMBLY WHERE THE FOLD IS CREASED INTO THE WEB. VERTICAL SEALER THE WEB WRAPS AROUND THE VERTICAL SEALER UNIT THAT FORMS THE VERTICAL POUCH SEALS. WHILE MOVING AROUND THE SEALER, THE WEB RIDES ON HEATED LANDS THAT FUSE THE SEALANT LINING OF THE WEB. THE WEB BETWEEN THE LANDS RECEIVES NO DIRECT HEAT AND DOES NOT SEAL. A PRESSURE ROLLER LIGHTLY PRESSES THE WEB AGAINST THE LANDS JUT BEFORE THE WEB LEAVES THE VERTICAL SEALER TO AID SEAL FORMATION. TEAR NOTCHER AS THE WEB IS PULLED BETWEEN THE TEAR NOTCHER AND ITS BACK-UP ROLLER, A NOTCH IS CREATED IN THE TOP EDGE OF THE WEB. THE PHASING OF THE TEAR NOTCHER CAN BE ADJUSTED. TO ALLOW PLACEMENT OF THE NOTCH ANYWHERE ALONG THE WEBS TOP EDGE. COOLING ROLLER THE COOLING ROLLER HAS TWO FUNCTIONS. FIRST, THE VERTICALLY SEALED WEB IS PULLED AROUND THE COOLING ROLLER TO ALLOW THE SEALS TIME TO SET BEFORE THE POUCHES ARE FILLED. SECOND, THE COOLING ROLLER ROTATES ON A MANUALLY-OPERATED SCREW THAT CAN BE ADJUSTED TO ALTER THE WEB POSITION AND ALIGN THE VERTICAL SEALS TO THE FILLER WHEEL VACUUM LANDS. TUCKING ROLLERS THE THREE TUCKING ROLLERS GUIDE THE WEB ONTO THE VACUUM LANDS OF THE FILLER WHEEL. THE ROLLERS ARE ARRANGED SO THAT THE WEB WINDS THROUGH THEM IN AN S-SHAPED PATH TO MAINTAIN PROPER TENSION. FILLER WHEEL ASSEMBLY AS THE WEBS VERTICAL SEALS ARE POSITIONED ON THE VACUUM LANDS BY THE TUCKING ROLLERS, AIR JETS B LOW THROUGH THE EMPTY FILLER WHEEL SPOUTS AND AGAINST THE WEB LIP TO COMPLETELY OPEN EACH POUCH. A TUCKER LOCATED BETWEEN EACH PAIR OF VACUUM LANDS RISES UP BELOW EACH POUCH TO CREATE A TUCK IN THE BOTTOM OFF THE POUCH TO AID POUCH OPENING. TOP SEALER THE POUCHES CLOYS AS THE WEB IS PULLED FROM THE FILLER WHEEL. AS THE WEB OF CLOSED POUCHES PASSES THROUGH THE TOP SEALER, THE TOP SEAL AREA IS HEATED BY HOT AIR TO SEAL THE POUCHES. SECOND FEED ROLLERS THE SECOND FEED ROLLERS, LOCATED JUST DOWNSTREAM FROM THE TOP SEALER, PULL THE WEB FROM THE FILLER WHEEL AND COMPRESS THE TOP SEAL. KNIFE AND TRANSFER SECTION THE KNIFE OPERATES INDEPENDENTLY FROM THE REST OF THE POUCH KING TO RECEIVE POUCHES THAT ARE COMPLETELY FORMED, FILLED, AND SEALED BUT STILL STRUNG TOGETHER. THE KNIFE CUTS THE POUCHES APART AND PASSES THEM TO THE TRANSFER. PIN CONVEYORS THE PIN CONVEYORS RECEIVE CUT POUCHES FROM THE KNIFES TRANSFER WHEELS AND MOVE THEM TO THE MARK III TRANSFER. WHILE THE LARGER POUCHES TAKE AN UNOBSTRUCTED ROUTE TO THE MARK III ON LANES 3 AND 4, THE SMALLER POUCHES ON LANES 1 AND 2 MAKE A RIGHT-ANGLE CHANGE IN DIRECTION BEFORE REACHING THE MARK III. GENERAL INFO: R.A JONES CREATED AND PATENTED THE POUCH KING , A HIGH PERFORMANCE POUCH-FILLING MACHINE MORE THAN 30 YEARS AGO. THIS IMPROVED, HIGH-END SYSTEM EMPLOYS PRINTED CIRCUIT HEATING TECHNOLOGY, WHICH PROVIDES A PRECISE TEMPERATURE PROFILE ACROSS THE VERTICAL SEAL BARS OF THE MACHINERY, MAKING A VIRTUALLY FLAWLESS LAMINATED SEAL. THE POUCH KING HAS A WIDE RANGE OF FEEDING SYSTEMS FOR BOTH INDIVIDUAL AND MULTI-COMPONENT BLENDS, ENABLING THE CUSTOMER TO HAVE OPTIMAL FILLING AND ACCURACY CONTROL. AFTER FILLING THE POUCHES, R.A JONES HAS A VARIETY OF TRANSFERS AVAILABLE, FROM MULTI-LANE DISCHARGE TO FULLY AUTOMATED CARTONING. THE POUCH KING CAN RUN OVER 4000 LINEAR INCH MINUTES IN STANDARD FORMAT AND OVER 7000 LINEAR INCHES OF WEB PER MINUTE FOR ULTRA HIGH SPEED APPLICATIONS. POUCH SIZE RANGE: LINEAR SPEED - OVER 7,000 LINEAR INCHES PER MINUTE POUCH WIDTH - 2 (51 MM) TO 8 (203 MM) POUCH HEIGHT - 2 (51 MM) TO 7.5 (190 MM) O

PACKWEST WATERFALL CAP SORTER MODEL: #12 CAP ELEVATOR/SORTER/FEEDER SERIAL NUMBER: CESF-QC-2584

FULLY AUTOMATED HIGH SPEED HORIZONTAL FLOW WRAPPER ARTY 75H - FULLY AUTOMATED HIGH-SPEED HORIZONTAL FLOW WRAPPER ARTY 75H MODEL: ARTY75H-SERVO1 S/N: 9480917 VOLTS: 208/230 WATTS: 3450 AMPS: 15 PHASE: 1 PSI: 80 HZ: 60 FILM DIMENSIONS: 80MM X 40MM X 2MM GENERAL INFO: THE ARTY75H IS A VERSATILE, LOW MAINTENANCE, HORIZONTAL FLOW WRAPPER FOR PILLOW-TYPE APPLICATIONS AND OFFERS HI-VALUE FOR THE DOLLAR. THE END USERS ARE SMALL AND MEDIUM CORPORATIONS IN THE FOLLOWING INDUSTRIES: BAKERIES, BREAD, AND PASTRIES COOKIE MANUFACTURES CONFECTIONERY MANUFACTURERS CONTRACT PACKAGERS SNACK FOOD MANUFACTURERS FEATURES: NO TOOLS AND NO SPECIAL SKILLS ARE NEEDED FOR SETUP. TURN ONE HAND-WHEEL TO ADJUST THE BAG LENGTH, TURN ONE KNOB TO ADJUST THE BAG WIDTH, SWITCH OFF THE INFEED CONVEYOR AND PLACE IT IN POSITION WITH THE JAWS, GUIDE THE PRODUCT WITH THE TELESCOPIC SIDE RAILS. NO CHANGE PARTS ARE NEEDED FROM ONE APPLICATION TO ANOTHER BY USING AN ADJUSTABLE FORMING BOX AND TELESCOPIC SIDE RAILS. QUICK CHANGE-OVER MADE POSSIBLE BY USING A SELF-CENTERING REEL HOLDER. MAINTENANCE-FREE DRIVE SYSTEM USING A 3 PHASES AC MOTOR AND VARIABLE SPEED AC DRIVE. EASY CLEANING, ALL PARTS IN CONTACT WITH THE PRODUCT ARE REMOVABLE WITHOUT TOOLS AND ARE MADE FROM STAINLESS STEEL #304. LOW MAINTENANCE, PERMANENTLY LUBRICATED GEARBOX WITH SYNTHETIC OIL, MERCURY ROTARY SWITCHES INSTEAD OF SLIP RINGS AND BRUSHES, SELF-LUBRICATING BEARINGS EVERYWHERE THIS IS POSSIBLE. MOBILITY, THE MACHINE CAN BE EQUIPPED WITH FOUR CASTORS AND FOUR LEGS. ALL PARTS AND COMPONENTS ARE SOURCED IN NORTH AMERICA.

SOUTHERN CALIFORNIA PACKAGING LABELER ST2100 - ONE (1) ST1100 RH WIPE-ON LABEL APPLICATOR O 12 DIAMETER UNWIND AND 6 WIDE WEB WIDTH. ONE (1) 6 WIDE X 6 FT HIGH FRICTION BELT CONVEYOR (5 WIDE BELT). ONE (1) POWDERCOATED STEEL BASE FRAME WITH LOCKING CASTERS AND LEVELING PADS. PRODUCT THROUGHPUT: 120-150 PPM (MANUALLY LOADED). PRODUCTS: FLAT POUCHES 1.625 X 3.125. LABEL SIZES: 1.25 X 2.75 (COPY POSITION TBD). VOLTS: 120 HZ: 60 AMPS: 10 PHASE: 1. ST2100 GENERAL INFO: THE ST2100 AUTOMATIC LABEL APPLICATOR IS A HIGH-PERFORMANCE LABELING HEAD CAPABLE OF APPLYING TO DIE CUT PRESSURE-SENSITIVE LABELS AT SPEEDS OF UP TO 2100 LINEAR INCHES PER MINUTE. ST2100 LABEL APPLICATOR SPECIFICATIONS HEAVY-DUTY CONSTRUCTION IS SPECIFICALLY DESIGNED FOR INDUSTRIAL APPLICATIONS. MICROPROCESSOR CONTROLLER GIVES FLEXIBLE AND ACCURATE LABEL PLACEMENT. STAINLESS STEEL AND ANODIZED ALUMINUM PROVIDE PROTECTION FROM CORROSIVE ENVIRONMENTS. THE APPLICATOR HEAD CAN BE ORIENTED TO ANY ATTITUDE FOR SIDE, TOP OR BOTTOM PLACEMENT. HANDLES A FULL VARIETY OF LABEL SHAPES AND SIZES. WIPE ON LABELER GENERAL INFO: THE WIPE-ON AUTOMATIC LABELING SYSTEM IS A HIGH-PERFORMANCE LABELING SYSTEM CAPABLE OF APPLYING TO DIE CUT PRESSURE-SENSITIVE LABELS AT SPEEDS OF UP TO 90 PRODUCTS PER MINUTE. STANDARD WIPE-ON SYSTEMS COME COMPLETE WITH AN 8-FOOT BY 6-INCH TTC CONVEYOR, A SINGLE APPLICATOR HEAD I/O MOUNT, A MICROPROCESSOR CONTROLLER, GUIDE RAILS, PRODUCT SENSOR MOUNT, AND A SPACER WHEEL ASSEMBLY. COMPATIBLE WITH OUR ST600, ST1100, ST2100, AND PA4000 AUTOMATIC LABEL APPLICATORS. S/N: 318460917

MARBURG M-6 AUTO CAPSEALER MODEL: MRBM56-S008 S/N: 20308-10 DOM: JUN. 06 VOLTS: 120 PHASE: 1 HZ: 60 GENERAL INFO: THE SIMPLICITY OF DESIGN, USER-FRIENDLY INTERFACE, AND EASE OF USE MAKE IT EASY FOR LINE PERSONNEL TO UNDERSTAND AND OPERATE. USING A SPACING WHEEL INSTEAD OF TRADITIONAL FEED-SCREW PRODUCT TRANSPORT MECHANISMS, CHANGEOVER TAKES LESS THAN 10 MINUTES, THEREBY INCREASING OUTPUT AND EFFICIENCY. ONCE YOU'VE ENJOYED THE INCREASED OUTPUT & EFFICIENCY, YOU'LL UNDERSTAND WHY HUNDREDS OF COMPANIES HAVE CHOSEN MARBURG INDUSTRIES' PRODUCTS. FEATURES: SPEEDS UP TO 100 BOTTLES PER MINUTE M5 SERIES SIZE RANGE 25-90 MM LF M6 SERIES SIZE RANGE 25-122MM LF BAND LENGTHS TO 3" FAST CHANGEOVER SPACING WHEEL FOR MORE EFFICIENT BOTTLE HANDLING DURABLE STAINLESS STEEL CONSTRUCTION QUICK WASH DOWN COMPACT SPACE-SAVING DESIGN EASY TO USE AND MAINTAIN MADE IN USA

[KANEBO TVIS-EX2] KANEBO TABLET INSPECTION MACHINE TVIS-EX2 MODEL: TVIS-EX2 S/N: T2330640 USES NIKON AF NIKKOR 50 MM LENS OVERVIEW: TABLET FED TO THE HOPPER, ARE TRANSFERRED TO TEH FLOW CONTROL TURNTABLE BY THE VIBRATORY FEED. TABLETS ARE PROPERLY ALIGNED IN A SINGLE LINE AND SENT O THE INSPECTION SUBSYSTEM. AT THE INSPECTION SUBSYSTEM, TABLETS ARE TRANSFERRED BY THE DISC CONVEYOR UNIT TO PASS THROUGH SIDE-1/2 AND SIDE 3/4 LIGHTING UNITS FOR CIRCUMFERENTIAL SIDE INSPECTION; AND THROUGH FACE-1 AND FACE-3 LIGHTING UNITS BY THE 1ST AND 2ND BELT CONVEYOR UNITS FOR FACE AND BACK INSPECTION. WHILE EACH TABLET PASSES THROUGH LIGHTING UNITS, IMAGES ARE PROCESSED FOR INDIVIDUAL JUDGMENT AND INDIVIDUAL JUDGMENTS ARE THEN COMPLIED FOR OVERALL JUDGMENT. BASED ON THE OVERALL JUDGMENT, DEFECTIVE AND ACCEPTABLE TABLETS ARE AUTOMATICALLY SEPARATED BY THE REJECTOR UNIT. POWER SUPPLY: AC 200V 3-PHASE, 50/60 HZ FOOTPRINT: 52X49X80 APPLICABLE TABLETS: NON-COATED, FILM COATED, SUGAR COATED TABLETS. TABLETS WITH PRINTED MARK ON ONE OR BOTH SIDES, SCORED TABLETS, ENGRAVED TABLETS, CIRCULAR TABLETS, OTHER TYPE OF TABLETS(OBLONG, OVAL, ETC.) TABLET SIZE: CIRCULAR SIZE: 5-12MM IN DIAMETER AND 2-8MM IN THICKNESS NON-CIRCULAR TABLETS 5-12MM WIDTH, 2-8MM THICKNESS, 5-21MM LENGTH INSPECTED ITEMS: DIRT: FOREIGN MATTER, DIRT, SCRATCH. SHAPE: DIMENSIONS, CRACK, DEFORMATION. CHIP: CHIPPED EDGE. PRINTED MARK: SCRATCHY MARK, BLURRED MARK, NO MARK. COLOR: DIFFERENT COLOR, DISCOLORATION, BLOTCHES, PEELING OF COATING. INSPECTION AREA: FACE: 1 SIDE: 4 ACCURACY: DETECTION OF DEFECTS EQUIVALENT TO A 50UM SQUARE OR LATER BLACK SPECK PROCESSING CAPACITY: CIRCULAR TABLETS 2000-3600 TABLETS/MIN. NON-CIRCULAR TABLETS 800-3000 TABLETS/MIN

[KANEBO TVIS-EX2] TABLET INSPECTION MACHINE - 1- KANEBO TABLET INSPECTION MACHINE TVIS-EX2 MODEL: TVIS-EX2 USES NIKON AF NIKKOR 50 MM LENS OVERVIEW: TABLET FED TO THE HOPPER, ARE TRANSFERRED TO TEH FLOW CONTROL TURNTABLE BY THE VIBRATORY FEED. TABLETS ARE PROPERLY ALIGNED IN A SINGLE LINE AND SENT O THE INSPECTION SUBSYSTEM. AT THE INSPECTION SUBSYSTEM, TABLETS ARE TRANSFERRED BY THE DISC CONVEYOR UNIT TO PASS THROUGH SIDE-1/2 AND SIDE 3/4 LIGHTING UNITS FOR CIRCUMFERENTIAL SIDE INSPECTION; AND THROUGH FACE-1 AND FACE-3 LIGHTING UNITS BY THE 1ST AND 2ND BELT CONVEYOR UNITS FOR FACE AND BACK INSPECTION. WHILE EACH TABLET PASSES THROUGH LIGHTING UNITS, IMAGES ARE PROCESSED FOR INDIVIDUAL JUDGMENT AND INDIVIDUAL JUDGMENTS ARE THEN COMPLIED FOR OVERALL JUDGMENT. BASED ON THE OVERALL JUDGMENT, DEFECTIVE AND ACCEPTABLE TABLETS ARE AUTOMATICALLY SEPARATED BY THE REJECTOR UNIT. POWER SUPPLY: AC 200V 3-PHASE, 50/60 HZ FOOTPRINT: 52X49X80 APPLICABLE TABLETS: NON-COATED, FILM COATED, SUGAR COATED TABLETS. TABLETS WITH PRINTED MARK ON ONE OR BOTH SIDES, SCORED TABLETS, ENGRAVED TABLETS, CIRCULAR TABLETS, OTHER TYPE OF TABLETS(OBLONG, OVAL, ETC.) TABLET SIZE: CIRCULAR SIZE: 5-12MM IN DIAMETER AND 2-8MM IN THICKNESS NON-CIRCULAR TABLETS 5-12MM WIDTH, 2-8MM THICKNESS, 5-21MM LENGTH INSPECTED ITEMS: DIRT: FOREIGN MATTER, DIRT, SCRATCH. SHAPE: DIMENSIONS, CRACK, DEFORMATION. CHIP: CHIPPED EDGE. PRINTED MARK: SCRATCHY MARK, BLURRED MARK, NO MARK. COLOR: DIFFERENT COLOR, DISCOLORATION, BLOTCHES, PEELING OF COATING. INSPECTION AREA: FACE: 1 SIDE: 4 ACCURACY: DETECTION OF DEFECTS EQUIVALENT TO A 50UM SQUARE OR LATER BLACK SPECK PROCESSING CAPACITY: CIRCULAR TABLETS 2000-3600 TABLETS/MIN. NON-CIRCULAR TABLETS 800-3000 TABLETS/MIN S/N: T8531150

KANEBO TVIS-EX2 TABLET INSPECTION MACHINE - 1- KANEBO TABLET INSPECTION MACHINE TVIS-EX2 MODEL: TVIS-EX2 S/N: T6030530 USES NIKON AF NIKKOR 50 MM LENS OVERVIEW: TABLET FED TO THE HOPPER, ARE TRANSFERRED TO TEH FLOW CONTROL TURNTABLE BY THE VIBRATORY FEED. TABLETS ARE PROPERLY ALIGNED IN A SINGLE LINE AND SENT O THE INSPECTION SUBSYSTEM. AT THE INSPECTION SUBSYSTEM, TABLETS ARE TRANSFERRED BY THE DISC CONVEYOR UNIT TO PASS THROUGH SIDE-1/2 AND SIDE 3/4 LIGHTING UNITS FOR CIRCUMFERENTIAL SIDE INSPECTION; AND THROUGH FACE-1 AND FACE-3 LIGHTING UNITS BY THE 1ST AND 2ND BELT CONVEYOR UNITS FOR FACE AND BACK INSPECTION. WHILE EACH TABLET PASSES THROUGH LIGHTING UNITS, IMAGES ARE PROCESSED FOR INDIVIDUAL JUDGMENT AND INDIVIDUAL JUDGMENTS ARE THEN COMPLIED FOR OVERALL JUDGMENT. BASED ON THE OVERALL JUDGMENT, DEFECTIVE AND ACCEPTABLE TABLETS ARE AUTOMATICALLY SEPARATED BY THE REJECTOR UNIT. POWER SUPPLY: AC 200V 3-PHASE, 50/60 HZ FOOTPRINT: 52X49X80 APPLICABLE TABLETS: NON-COATED, FILM COATED, SUGAR COATED TABLETS. TABLETS WITH PRINTED MARK ON ONE OR BOTH SIDES, SCORED TABLETS, ENGRAVED TABLETS, CIRCULAR TABLETS, OTHER TYPE OF TABLETS(OBLONG, OVAL, ETC.) TABLET SIZE: CIRCULAR SIZE: 5-12MM IN DIAMETER AND 2-8MM IN THICKNESS NON-CIRCULAR TABLETS 5-12MM WIDTH, 2-8MM THICKNESS, 5-21MM LENGTH INSPECTED ITEMS: DIRT: FOREIGN MATTER, DIRT, SCRATCH. SHAPE: DIMENSIONS, CRACK, DEFORMATION. CHIP: CHIPPED EDGE. PRINTED MARK: SCRATCHY MARK, BLURRED MARK, NO MARK. COLOR: DIFFERENT COLOR, DISCOLORATION, BLOTCHES, PEELING OF COATING. INSPECTION AREA: FACE: 1 SIDE: 4 ACCURACY: DETECTION OF DEFECTS EQUIVALENT TO A 50UM SQUARE OR LATER BLACK SPECK PROCESSING CAPACITY: CIRCULAR TABLETS 2000-3600 TABLETS/MIN. NON-CIRCULAR TABLETS 800-3000 TABLETS/MIN

KAPS ALL HORIZONTAL GAP BOTTLE CONVEYOR MODEL: BC-23 S/N: 5910 THE KAPS-ALL BOTTLE CONVEYOR IS BUILT TO TRANSPORT BOTTLES FROM ONE CONVEYOR TO ANOTHER, OR FOR BOTTOM CODING OR DEPUCKING, ETC... FEATURES: COMPLETELY PORTABLE ON HEAVY-DUTY CASTERS. ELECTRONICALLY CONTROLLED VARIABLE SPEED ADJUSTMENT FOR CARRIER BELTS TO ACCOMMODATE A WIDE RANGE OF APPLICATIONS. UPPER STRUCTURE WITH STANDARD STAINLESS STEEL SHAFTING, GUARDING, GRIPPER DRIVES, ETC. COMPLETELY ADJUSTABLE - NO CHANGEOVER PARTS REQUIRED. HANDLES VIALS UP TO 2-1/2 GALLONS OF PLASTIC, GLASS, OR METAL CONTAINERS OF ALL SHAPES AND STYLES. BOTTLE GRIPPER BELTS ARE ADJUSTABLE UP OR DOWN TO ACCOMMODATE MOST BOTTLE SIZES AND SHAPES. 1 HIGH BOTTLE GRIPPER BELTS. LEFT TO RIGHT CONVEYOR TRAVEL IS STANDARD CONVEYOR

2007 ISHIDA DIGITAL AUTOMATIC HIGH SPEED CHECK WEIGHING SYSTEM USED FOR RUNNING DAILY VITAMIN PACKETS MDL: DACS-WN-003-SB/PB-I WEIGHING CAPACITY: 300G MFG. DATE: APRIL, 2007 VOLTS: 120 AMPS: 2.5 HZ: 60 CONVEYOR DIMENSIONS: 6" WIDE, 95" LONG (EACH CONVEYOR)