Monthly MultiFacility CNC Fab No Reserve Auction

MORI SEIKI SL-25 CNC LATHE CHUCK SIZE 10" SWING OVER CROSSLIDE 13.7" MAX. SWING 20.4" MAX. CUTTING DIAMETER 10.24" MAIN SPINDLE BORE 3.54" MAIN BAR CAPACITY 2.625" MAIN SPINDLE MOTOR 20 HP MAIN SPINDLE SPEED 35 - 3500 RPM TURRET STATIONS 10 MSD-516II CONTROL MACHINE WEIGHT 10,000 LBS MACHINE SIZE 122" X 74" X 77" TALL

2000 KAESER BS 61 AIR COMPRESSOR 3 PHASE 60 HZ / 1800 RPM 50 HP PSIG: 125 CFM: 225 VOLTAGE: 460

CINCINNATI 107-4 CENTERLESS GRINDER DIAMETER CAPACITY: 0" 1 1/2" REGULATING WHEEL DIAMETER: 9" REGULATING WHEEL HOLE DIAMETER: 4" REGULATING WHEEL WIDTH: 4" REGULATING WHEEL SPEED: 10 300 RPM GRINDING WHEEL DIAMETER: 16" GRINDING WHEEL HOLE DIAMETER: 10" GRINDING WHEEL WIDTH: 4" GRINDING WHEEL MOTOR: 7 1/2 HP WEIGHT 6000 LBS. DIMENSIONS 8FT X 8FT X 6FT

MINSTER PRESS 7 MODEL 7 75 TON BOLSTER SIZE: 35 X 24 STROKE PER MINUTE: 120 SHUT HEIGHT ON BED STROKE DOWN ADJUSTMENT IN INCHES: 15"

CORKEN D91AJ4PFDDNSNN-103 GAS COMPRESSOR CORKEN OIL FREE BOOSTER COMPRESSOR PACKAGE MODEL D91AJ4PFDDNSNN-103 DESIGNED FOR CONTINUOUS DUTY, 3 HP TEFC 460 VOLT BASE MOUNTED OPERATIONAL DATA -400 RPM, LOW PUMP SPEED -32.1 SCFM AT 230 PSIG OUTLET -120 PSIG INLET (80F IN 180F OUT) COMPRESSOR -SINGLE STAGE BOOSTER -PEEK VALVE PLATES -VITON O-RINGS -STEEL VALVE GASKETS -SPLASH LUBRICATED CRANKCASE MOUNTING -STEEL BASE PLATE -ENCLOSED BELT GUARD -ADJUSTABLE MOTOR SLIDE BASE -V-BELT DRIVE -CONTROL PANEL STAND WITH CONTROLS - NEMA 12 ENCLOSURE -3 HP IEC CONTACTOR -THERMAL OVERLOAD WITH THROUGH DOOR RESET -MAIN CIRCUIT WITH THROUGH THE DOOR DISCONNECT HANDLE -CONTROL TRANSFORMER WITH PRIMARY AND SECONDARY FUSES -HAND/OFF AUTO SELECTOR SWITCH -PRESSURE SWITCH FOR AUTO CONTROL (200 PSIG START, 230 PSIG STOP) -PRESSURE SWITCH FOR MINIMUM INLET PSI (120 PSI) -INDICATION LIGHTS FOR LOW INLET PSI AND HIGH TEMP SHUTDOWNS -DIGITAL HOUR METER -HIGH DISCHARGE TEMPERATURE SWITCH

INDEXABLE TOOLING AND FACE MILLS COUNT: 10 PIECES

2019 RDI COIL FLATTENER ROLL DIAMETER: FLATTENER - 2.2 INCHES (56 MM) WITH POLYURETHANE COVERING (80-85 DUROMETER) FEED IN/OUT - 3.78 INCHES (96 MM) WITH HARD CHROME SURFACE ROLL QUANTITY: FEED ROLLS - 4 (1 ROLL SET ENTRY AND 1 EXIT) FLATTENER 11 (5 OVER 6 CONFIGURATION WITH BACKUP ROLLS) ROLL ADJUSTMENTS: TOP ROLLS ADJUSTABLE VIA MOTORIZED ADJUSTMENT WITH HINGED ROLL OPENING MECHANISM FOR EASY CLEANING ROLL DRIVE: ROLLS DRIVEN BY AN AC MOTOR AND GEAR REDUCER TRANSMITTING POWER TO EACH ROLL VIA CHAIN AND SPROCKET ROLL TYPE: 52100 STEEL HARDENED ROLL BACKUPS: TOP AND BOTTOM SIDE GUIDES: AUTOMATIC, CENTERLINE JUSTIFIED LUBRICATION: AUTOMATIC LUBRICATION ELECTRICAL: PUSHBUTTON STATION MOUNTED AT THE MAIN OPERATOR CONSOLE TO CONTROL POWERED FUNCTIONS PNEUMATIC: PNEUMATIC VALVES MOUNTED TO MACHINE BASE AND FACTORY WIRED TO A MACHINE MOUNTED JUNCTION BOX HYDRAULIC: HYDRAULIC VALVES MOUNTED TO MACHINE BASE AND FACTORY WIRED TO A MACHINE MOUNTED JUNCTION BOX EQUIPPED WITH: INFEED ROLLERS NEED TO BE REPLACED, BUT EVERYTHING ELSE IS IN GREAT CONDITION WAS ONLY IN SERVICE FOR 1.5 YEARS

FIXTURE ACCESSORY ORGANIZERS (2) FIXTURE SCREW, NUT AND WASHER ORGANIZERS. WITH FIXTURES AS PICTURED.

2003 OKUMA MA-40HA HORIZONTAL MACHINING CENTER X AXIS TRAVEL: 22.05" Y AXIS TRAVEL: 24.01" Z AXIS TRAVEL: 24.61" RAPID RATE X AXIS: 1,574 IPM RAPID RATE Y AXIS: 1,574 IPM RAPID RATE Z AXIS: 1,574 IPM PALLET SIZE: 15.75" X 15.75" MAX PALLET LOAD: 880 LBS SPINDLE SPEED: 15,000 RPM SPINDLE MOTOR: 35 HP SPINDLE TAPER: 40 CT TOOL CHANGER: 30 ATC EQUIPPED WITH: CHIP CONVEYOR COOLANT THRU SPINDLE PROBING OSP-E100M CONTROL DIMENSIONS: 170" X 105" X 120" WEIGHT: 25,000 LBS

2000 MITSUBISHI M-H4B/16 HORIZONTAL MACHINING CENTER PALLET SIZE (CAP.) 15.75" X 15.75" / (880 LBS.) PALLET INDEXING (B-AXIS) 0.001DEG SPINDLE NOSE TO TABLE CENTER 5.9" - 31.5" SPINDLE CENTER TO TABLETOP 2" - 24" X-AXIS TRAVEL 25.6" Y-AXIS TRAVEL 25.6" Z-AXIS TRAVEL 25.6" SPINDLE TAPER CT 40 SPINDLE SPEED 12,000 RPM SPINDLE MOTOR 30 HP. TOOL CHANGER CAPACITY: 60 STATIONS RAPID TRAVERSE RATES 1,575 IPM TOOL CHANGE TIME (T-T / C-C) 1.3 / 3.8 SECS. MAXIMUM TOOL DIAMETER / WEIGHT / LENGTH 5.9" / 11.8" / 18 LBS. ELECTRICAL REQUIREMENTS 230V/3PH/60HZ EQUIPPED WITH: CHIP CONVEYOR FANUC 18I-M CONTROL PROBING COOLANT THRU SPINDLE MACHINE DIMENSIONS 17"L X 11"W X 10"H MACHINE WEIGHT 23,150 LBS.

CINCINNATI 5 SERIES 135 TON PRESS BRAKE, 8FT OVERALL LENGTH, BETWEEN THE HOUSING LENGTH: 78" W/ LIGHT CURTAINS PNEUMATIC/MECHANICAL PRESS TONNAGE -135 TON OVERALL LENGTH - 8FT BETWEEN THE HOUSING LENGTH - 78 DOES IT HAVE A BACK GAUGE/LENGTH OF BACK GAUGE - NO BACK GAUGE HOW MANY AXES ARE ON THE MACHINE - Y AXIS ONLY TYPE OF CONTROL - NO COMPUTER, MANUAL OPERATION/ PUSH BUTTON DOES IT GO INTO THE GROUND- NO, FLOOR MOUNTED ONLY DOES IT HAVE AUTO-CROWNING - NO AUTO-CROWNING DOES IT HAVE HYDRAULIC CLAMPING - NO HYDRAULIC CLAMPING, OLD SCHOOL SOCKET WRENCH TYPE OF CONTROL AND SOFTWARE/RAM AND/OR BED - NO SOFTWARE CLUTCH AND BRAKE MECHANISMS, 3 12 BED FRONT SUPPORT ARMS- HOW MANY - YES, 2 FRONT SUPPORT ARMS, 2 BACK SUPPORT ARMS LIGHT CURTAINS - YES, INSTALLED, NEVER USED.

CAT40 MILLING CHUCKS TOOL HOLDERS AND SHELL FACE MILL HOLDER COUNT: 6 PIECES

CAT40 AND BT40 COLLET TOOL HOLDERS COUNT: 11 PIECES

CAT 40 SIDE LOCK TOOL HOLDERS COUNT: 12 PIECES

BRIDGEPORT R8 TOOL HOLDERS TOTAL COUNT: 13 PIECES

2010 DOMNICK HUNTER MAXIGAS 112 NITROGEN GAS GENERATION SYSTEM (DUPLEX PRESSURE SWING ABSORPTION TYPE SYSTEM 165 SCFM COMPRESSED AIR INLET FLOW AT 150 PSIG 39.3 SCFM 99.9% NITROGEN DISCHARGE AT 130 PSIG 2 MAXIGAS-112 UNITS IN PARALLEL 2 BUFFER MIXING TANKS DIGITAL DISPLAY OF O2 ECONOMY STANDBY CONTROL FLOW VERIFICATION INDICATOR 115 VOLT, SINGLE PHASE POWER REQUIREMENT 12 CONNECTION FOR N2 1 CONNECTION FOR INLET COMPRESSED AIR DIMENSIONS: 76 H X 22 W X 55 D PER MODULE WEIGHT: 1490 LBS. PER MODULE PLUS BUFFER TANK)

2001 ACER SUPRA 61311 SURFACE GRINDER, 2 HP SPINDLE MOTOR, BUILT IN 2001 2 HP SPINDLE MOTOR FRONT MOUNT SPINDLE WITH RUN-OUT WITHIN 0.00008" TABLE OVERALL FLATNESS WITHIN 0.00012" WHEEL GUARD WITH CAPACITY FOR 8" WHEEL LONGITUDINAL TABLE STROKE IS 20" CONTINUOUS LOOP-COG TIMING BELT SYSTEM CROSSFEED LOCK ADJUSTABLE LONGITUDINAL TABLE STOPS MEEHANITE CASTED SADDLE WITH DOUBLE-V TURCITE WAYS SAFETY 24 VOLT CIRCUIT CONTROL PUSH BUTTON MANUAL STARTER WITH OVERLOAD PROTECTION DISTANCE BETWEEN DOUBLE-V IS 19.6" APART THE WIDTH OF MACHINE BASE IS 22" FC 25 MACHINE BASE WEIGHS MORE THAN 1,584 LBS MAXIMUM WORK LOAD AT 320 LBS

INDUSTRIAL VIBRATORY TUMBLER WITH EXTRA MEDIA INCLUDED

KURT 8 INCH VICE

SQUEEZE ACTION CLAMPS

TOGGLE CLAMP AND ADDITIONAL FIXTURING