No Reserve Food and Beverage Processing Equipment

RYSON 12" W LEFT HAND TURN DECLINE SPIRAL CONVEYOR - USED RYSON SPIRAL CONVEYOR WITH: DECLINE SPIRAL CONVEYOR COUNTER-CLOCKWISE SPIRAL 180 DEGREE PRODUCT DISCHARGE, PRODUCT ENTERS AND EXITS THE CONVEYOR ON THE SAME SIDE INFEED HEIGHT: 126 INCHES OUTFEED HEIGHT: 30 INCHES OUTSIDE DIAMETER: 63 INCHES INFEED LENGTH: 33.25 INCHES OUTFEED LENGTH: 31.75 INCHES CONVEYOR BELT WIDTH: 12 INCHES ELEVATION CHANGE: 8 FEET NUMBER OF TURNS: 6.5 AT 5.38 DEGREES PER TURN 2 HORSEPOWER MOTOR SPEED: 75FPM @ 60HZ

[1/2 TON HOIST] HAMISCHFEGER P&H SWING ARM CRANE WITH: STEEL CONSTRUCTION LIFTING CAPACITY: 1/2 TON ELECTRICAL REQUIREMENTS: VOLTAGE: 115/460 AMPS: 10.0 HERTZ: 60 PHASE: 3

SACMI OPERA 200RF ROLL FED WRAPAROUND GLUE LABELER: HIGH SPEED LABELING SYSTEM FOR PET, GLASS, AND METAL CONTAINERS CAN HANDLE CYLINDRICAL OR SHAPED CONTAINERS TRANSFER OF THE LABEL FROM THE CUTTING DRUM TO THE CONTAINER IS CARRIED OUT BY MEANS OF AN ALUMINUM VACUUM DRUM WITHOUT GRIPPERS OUTPUT: UP TO APPROXIMATELY 40,000 CONTAINERS PER HOUR, DEPENDING ON LABEL AND CONTAINER SIZES PREVIOUSLY USED TO LABEL COFFEE CANS: CAN DIMENSIONS: 4.25 INCH DIAMETER X 5 INCHES TALL LABEL WIDTH: 5 INCHES LABEL LENGTH: 13.35 INCHES TIMING SCREW AND STARWHEEL INFEED RIGHT TO LEFT PRODUCT FLOW 90 DEGREE TURN OUTFEED, RELATIVE TO THE INFEED STAINLESS STEEL AND FOOD GRADE CONSTRUCTION ALLEN-BRADLEY PANELVIEW PLUS 1000 HMI ALLEN-BRADLEY COMPACTLOGIX L35E CONTROLS

MAGNUM 4500-SDR TOP ONLY RANDOM CASE TAPER 3" TAPE - USED MAGNUM CASE TAPER WITH: TOP TAPEHEAD AND BACKUP TAPEHEAD TAPE SIZE: 3 INCHES OUTPUT: RANDOM MODE: UP TO 15 BOXES PER MINUTE UNIFORM MODE: UP TO 30 BOXES PER MINUTE CASE SIZE RANGE: LENGTH: 5 TO UNLIMITED INCHES WIDTH: 5 TO 24 INCHES HEIGHT: 5 TO 24 INCHES BELT SPEED: 75 FEET PER MINUTE ADJUSTABLE WORKING HEIGHT: 27 TO 35 INCHES ELECTRICAL REQUIREMENTS: VOLTAGE: 120V FREQUENCY: 60 HERTZ PUSHBUTTON AND SELECTOR SWITCH CONTROLS STEEL CONSTRUCTION MOUNTED ON LOCKING CASTERS S/N: H211-203-16453

USED SEALED AIR RAPID FILL RANDOM TOP ONLY CASE TAPER WITH: MODEL:RAPID FILL SERIAL:AF-1251 APPLICATION: AUTOMATICALLY FILLS VOID BAGS INSIDE OF CARTONS AS IT IS SEALED. UNINFLATED BAG IS CLIPPED TO THE CORNER OF THE CASE, FLAPS ARE CLOSED, CASE IS TAPED, THEN VOID BAG IS FILLED. CAPACITY: UP TO 10 CARTONS PER MINUTE TAPE HEAD WIDTH: 3 INCHES TOP TAPE HEAD ONLY AIR REQUIREMENTS: 8-10 CFM AT 100 PSI PERSONNEL GUARDING ADJUSTABLE WORKING HEIGHT CASTERS

WEXXAR WFH AUTOMATIC GLUE BOTTOM SEAL CASE ERECTOR - USED WEXXAR WFH GLUE BOTTOM SEAL CASE ERECTOR WITH: MODEL:WFH SERIAL:1477 POWERED BLANK CASE MAGAZINE WITH PIN AND DOME CASE FORMING PLATES OUTPUT: UP TO 20 CASES PER MINUTE, DEPENDING ON APPLICATION CASE BLANK DIMENSIONS: 72 LENGTH X 24 WIDTH (INCHES) CASE SIZE RANGE: MINIMUM (INCHES): 6 LONG X 5 WIDE X 3.5 HIGH MAXIMUM (INCHES): 24 LONG X 16.5 WIDE X 16.5 HIGH NORDSON HOT GLUE UNIT ELECTRICAL: 460 VOLTS, 3 PH, 60 HZ OVERALL DIMENSIONS: 145 LENGTH X 51 WIDTH X 80 HEIGHT (INCHES) LEFT HAND CASES

DT INDUSTRIES DUAL LAKSO MDL-300 COTTONER MACHINE WITH: MODEL:MDL-300 SERIAL:300-173 CONVEYOR: WIDTH: 3 INCHES LENGTH: 127 INCHES HEIGHT: 36 INCHES PRODUCT CLEARANCE: 7 INCHES BOTTLE INSPECTION SYSTEM INCLUDED TOUCH SCREEN HMI INTERFACE STAINLESS STEEL

OK INTERNATIONAL BAG-IN-BOX BAG INSERTER MAKES A POLY BAG FROM A ROLL STOCK FILM AND INSERTS IT INTO A CARTON CONVEYOR DIMENSIONS: 55 INCHES LONG X 10 INCHES WIDE CONVEYOR HEIGHT: 27 INCHES ALLEN-BRADLEY SLC 500 CONTROLS STAINLESS STEEL CONSTRUCTION

DOBOY CBS-CH CHAIN-FED CONTINUOUS BAND BAG SEALER WITH: CONTINUOUS, CHAIN-FED BAG SEALER DESIGNED FOR HEAVIER BAGS OUTPUT: UP TO 425 INCHES PER MINUTE - DEPENDING ON PRODUCT, BAG MATERIAL AND OPERATOR ABILITY SEAL WIDTH: .5 INCHES TWO SETS OF HEATING AND COOLING BARS ANGLED SEALING TILT DRIVE HEAD DIGITAL TEMPERATURE CONTROLS COMPATIBLE WITH PLASTIC BAGS RIGHT TO LEFT PRODUCT FLOW

60 GALLON SS SINGLE WALL TANK - USED STAINLESS STEEL CHERRY-BURRELL TANK: CAPACITY: APPROXIMATELY 60 GALLONS TANK DIMENSIONS: HEIGHT: 34 INCHES DIAMETER: 23 INCHES SINGLE WALL SIDE BOTTOM DISCHARGE STAINLESS STEEL CONSTRUCTION MOUNTED ON CASTERS

1130 LINCOLN IMPINGER SINGLE STACK SS OVEN - USED LINCOLN IMPINGER DOUBLE STACK SS OVEN WITH: TEMPERATURE RANGE: 250 FAHRENHEIT TO 575 FAHRENHEIT 30 MINUTE COOK TIMER BAKING CHAMBER: WIDTH: 19 INCHES LENGTH: 28 INCHES HEIGHT: 3 INCHES CONVEYOR: WIDTH: 19 INCHES LENGTH: 56 INCHES ELECTRICAL: 208 VOLTS, 60 HERTZ, SINGLE PHASE

VERTICAL FORM FILL SEAL BAGGER - USED BAGGER WITH: DESIGNED FOR SEALING BAGS UP TO 8 INCHES WIDE SEAL JAW WIDTH: 10 INCHES SOMBRERO HOLE PUNCH-OUT PNEUMATIC KNIFE FILM CUT FORMER DIAMETER: 3.5 INCHES MAXIMUM FILM WIDTH: 20 INCHES CURRENTLY SET TO RUN 15.25 INCH WIDE FILM RIBBON TRANSFER CODER MITSUBISHI PLC PANASONIC MOTOR DRIVES WEINVIEW TOUCHSCREEN HMI ALL STAINLESS STEEL CONSTRUCTION CASTERS PREVIOUSLY RUNNING 16 OUNCE BAGS OF CHEESE AT A RATE OF 35 TO 40 BAGS PER MINUTE

14.5' LONG X 8" WIDE PLASTIC MAT TOP BELT CONVEYOR - USED SMOOTH BELT CONVEYOR WITH: DIMENSIONS: 14.5' LONG X 8 INCHES WIDE HEIGHT: 35 INCHES FROM FLOOR 1 HORSEPOWER MOTOR SMOOTH TOP BELT STAINLESS STEEL CONSTRUCTION

FRESHLINE MACHINES PLASTIC MAT-TOP CONVEYOR TILTED CONVEYOR BELT FOR USE IN HAND-PACK OPERATIONS LENGTH: 11 FEET WIDTH: 11 INCHES INFEED HEIGHT: 34 INCHES DISCHARGE HEIGHT: 34 INCHES DEPTH: 4 INCHES .5 HORSEPOWER MOTOR STAINLESS STEEL FRAME

[PRESTO] [M152] MANUAL LIFT CART WITH: 15 INCH LOAD CENTER 52 INCH RAISED HEIGHT 5.25 INCH LOW HEIGHT 1,000 POUND LIFT CAPACITY PLATFORM DIMENSIONS (INCHES): 24 W X 24 L S/N: 135663

SHANKLIN FLAT BELT INFEED 16"W X 78"L CONVEYOR - SHANKLIN FEED CONVEYOR H2064A 16"W X 78"L CONVEYOR WITH: MODEL:CONVEYOR BELT INF H2064A SERIAL:H0109 BELT: WIDTH: 16 INCHES LENGTH: 78 INCHES ADJUSTABLE RAIL: HEIGHT: 3 INCHES WORKING HEIGHT: 38 INCHES MOUNTED ON ADJUSTABLE FEET STAINLESS STEEL CONSTRUCTION

[20]" WIDE X 72" LONG - USED CONVEYOR WITH: WIDTH: 20 INCHES LENGTH: 72 INCHES HEIGHT: 24 INCHES INC.JET INDUSTRIAL CODING

[RUFONG RF-WL100] STAINLESS STEEL AUTOMATIC WET WIPE PACKAGING AND LID APPLICATING LINE - THE RUFONG RF-WL100 SERIES IS DESIGNED FOR THE PRODUCTION AND PACKAGING OF DISPOSABLE HOUSEHOLD CLEANING WIPES AND BABY WIPES. THIS FULLY AUTOMATED SYSTEM INTEGRATES SERVO MOTION CONTROLS AND A USER-FRIENDLY INTERFACE TO ENSURE CONTINUOUS OPERATION WITHOUT MANUAL INTERVENTION. ITS UNIQUE FEATURES INCLUDE AUTOMATIC MATERIAL SPLICING AND PRECISE LIQUID ADDITION, ENHANCING PRODUCTION AND PRODUCT QUALITY WHILE DECREASING DOWN TIME. COMBINED WITH THE RUFONG RF-LM100 WET WIPE LID APPLICATOR, THIS COMPLETE PACKAGING LINE IS IDEAL FOR MID-RANGE TO LARGE-SCALE WET WIPE PACKAGING OPERATIONS. USED RUFONG WET WIPE PACKAGING LINE WITH: RF-WL100 WET WIPE PACKER: PRODUCTION SPEED: UP TO 100 PACKS PER MINUTE DEPENDING ON PRODUCT, PACKAGE SIZE, AND APPLICATION SHEET OUTPUT: UP TO 8,000 SHEETS PER MINUTE DEPENDING ON PRODUCT AND APPLICATION MAXIMUM RAW MATERIAL ROLL DIMENSIONS (2): WIDTH: 17.3 INCHES EACH (440 MM) DIAMETER: 47.2 INCHES EACH (1,200 MM) MINIMUM WET WIPE DIMENSIONS: LENGTH: 4.7 INCHES (120 MM) WIDTH: 3.1 INCHES (80 MM) MAXIMUM WET WIPE DIMENSIONS: LENGTH: 8.7 INCHES (220 MM) WIDTH: 4.3 INCHES (110 MM) MINIMUM PACKAGE SIZE: LENGTH: 5.9 INCHES (150 MM) WIDTH: 3.1 INCHES (80 MM) HEIGHT: 0.4 INCHES (10 MM) MAXIMUM PACKAGE SIZE: LENGTH: 13.8 INCHES (350 MM) WIDTH: 4.7 INCHES (120 MM) HEIGHT: 3.5 INCHES (90 MM) RAW MATERIAL COMPATIBILITY: SPUNLACE CLOTH HOT-ROLLED CLOTH DEGRADABLE NON-WOVEN FABRIC WET-STRENGTH PAPER PACKAGING FILM ROLL DIMENSIONS: WIDTH: 16.5 INCHES (420 MM) DIAMETER: 14.2 INCHES (360 MM) COMPATIBLE PACKAGING MATERIALS: PET/PE BOPP PET/AL/PE FOLDING OPTIONS: "Z" POP-UP AND NON-POP-UP CONFIGURATIONS COLOR LCD TOUCH SCREEN HMI AUTOMATIC SPLICING: NON-STOP REPLACEMENT OF MATERIALS, INCLUDING NON-WOVEN FABRICS AND FILM ROLLS LIQUID ADDITION RANGE: BETWEEN 2 TO 5 TIMES THE DRY WEIGHT DIGITAL FLOWMETER MEASUREMENT AND FLOW CONTROL AUTOMATIC LEVEL CONTROL PIPELINE DISINFECTION: SANITARY-GRADE DESIGN SUITABLE FOR PASTEURIZATION AND DISINFECTANT FLUSHING CE SAFETY CERTIFICATION WITH MULTI-AXIS SERVO MOTION CONTROLLER APPROXIMATE OVERALL DIMENSIONS: LENGTH: 70.9 TO 84.6 FEET (21,500 TO 25,800 MILLIMETERS) WIDTH: 12.5 FEET (3,800 MILLIMETERS) HEIGHT: 6.9 FEET (2,100 MILLIMETERS) AIR REQUIREMENTS: BETWEEN 87 AND 116 PSI (0.6 - 0.8 MPA) ELECTRICAL: 3 PHASE, 50/60 HZ, 380 VOLTS, 100 AMPS RF-LM100 WET WIPE LID APPLICATOR: PRODUCTION SPEED: UP TO 100 PACKAGES PER MINUTE DEPENDING ON PACKAGE SIZE, PRODUCT, AND APPLICATION MINIMUM PACKAGE DIMENSIONS: LENGTH: 2 INCHES (50 MM) WIDTH: 2 INCHES (50 MM) HEIGHT: 0.4 INCHES (10 MM) MAXIMUM PACKAGE DIMENSIONS: LENGTH: 11.8 INCHES (300 MM) WIDTH: 7.9 INCHES (200 MM) HEIGHT: 4.7 INCHES (120 MM) MINIMUM LID DIMENSIONS: LENGTH: 2.0 INCHES (50 MM) WIDTH: 2.0 INCHES (50 MM) HEIGHT: 0.08 INCHES (2 MM) MAXIMUM LID DIMENSIONS: LENGTH: 7.1 INCHES (180 MM) WIDTH: 4.7 INCHES (120 MM) HEIGHT: 0.4 INCHES (10 MM) MAXIMUM LABEL ROLL DIMENSIONS: WIDTH: 3.9 INCHES (100 MM) DIAMETER: 14.2 INCHES (360 MM) APPLICABLE LABELS: TRANSPARENT AND NON-TRANSPARENT LABELS OVERALL DIMENSIONS: LENGTH: 14.2 FEET (4,320 MM) WIDTH: 4.5 FEET (1,370 MM) HEIGHT: 6.7 FEET (2,050 MM) AIR SOURCE REQUIRED: BETWEEN 87 AND 116 PSI (0.6 TO 0.8 MPA) ELECTRICAL: 3 PHASE, 50/60 HZ, 380 VOLTS BUYERS RESPONSIBILITY TO REMOVE THIS EQUIPMENT.