Warehouse Liquidation of industrial equipment and parts including CNC SMT PCB Test Measurement Inspection Lab and Commercial Kitchen

WOOD STONE WS-MS-5-RFG-IR-NG 5-FT MT ADAMS GAS-FIRED BRICK OVEN NAT + HOOD/TOOLS (1) EXHAUST HOOD (12) PADDLE/SPATULAS (1) BRUSH MT ADAMS RFG-IR RADIANT FLAME GAS + INFRARED BURNER 5 FOOT S/N: 1390 HOURLY BTU INPUT: 188,000 120VAC 50/60 HZ 1.1 AMPS GAS: NAT 3/4 INCH GAS INLET (FNPT) 1 DECK DECK LINING: STONE HEARTH HEARTH CAPACITY: 8" PIZZAS: 1216 10" PIZZAS: 1012 12" PIZZAS: 8 16" PIZZAS: 5 HOOD: 2 BAFFLES APPROXIMATE DIMENSIONS: 48"W X 24"H X 44"D THIS ITEM WAS WORKING PROPERLY WITH NO PROBLEMS WHEN WE REMOVED IT FROM A WORKING RESTAURANT. THE EXHAUST HOOD MOUNTS OVER THE TOP EXHAUST PIPE AS SEEN IN THE LAST IMAGES.

WILSON PFC-10-40SA-10C SIPHON PUMP FILTER FILTRATION SYSTEM 600-GPH BALDOR .75HP (1) WILSON PFC-10-40SA-10C SIPHON PUMP FILTER FILTRATION SYSTEM 600-GPH BALDOR .75HP INLET FILTER PARKER # 924448 OUTLET FILTER PARKER # 924450 FLOW RATE: 600 GPH 115VAC 1800 RPM 10 AMP 60 HZ MOTOR: MANUFACTURER: BALDOR FRAME: 56C .75 HP 60 HZ V: 115 / 208-230 1725 RPM SINGLE PHASE INDUSTRIAL MOTOR WHEN POWER WAS APPLIED, THIS ITEM RAN VERY SMOOTHLY. IT EASILY SUCKED UP MATERIAL AND EMITTED IT THROUGH THE OUTPUT PIPING WITH NO PROBLEMS.

WEBER 4050E CC LABEL PRINTER APPLICATOR LABELER SYSTEM TYPE: 30-RH-ZE543-LN200 LABEL PRINTER AND DISPENSER FOR ALL LABELING TASKS RIGHTHAND VERSION LABEL ROLL: UP TO 300MM DIAMETER, 450 RUNNING METERS, 3" CORE TAMP-BLOW APPLICATION SYSTEM TAMP APPLICATOR HAS LIMITED FORCE, NO SAFETY GUARDS OR PROTECTIVE CABINETS REQUIRED MAXIMUM TAMP SIZE: 160X210MM (WOULD REQUIRE LARGER TAMPING ADAPTER) APPLICATION RATE: TO 150 LABELS/MIN ZEBRA PRINTER MODEL: ZE500-4 P/N: ZE50043-R010000Z ZE500-SERIES PRINT ENGINE THERMAL TRANSFER OR DIRECT THERMAL PRINTING RIGHT-HAND VERSION 4" LABELS (UP TO 4.1" PRINT WIDTH, 4.5" MEDIA WIDTH) RESOLUTION UP TO 300 DPI INTERFACES: RS-232 SERIAL, PARALLEL, USB, 10/100 ETHERNET, RFID DESIGNED FOR OPERATION IN HARSH ENVIRONMENTS WITHOUT INTERRUPTIONS LARGE GRAPHICAL DISPLAY NO NEED FOR COOLING FANS, REDUCED DUST/WATER INTRUSION MAXIMUM PRINT SPEED: 305MM/SECOND TRANSMISSIVE AND REFLECTIVE MEDIA SENSORS MATRIX 300N 412-010 BARCODE READER HIGH RESOLUTION WITH LED ILLUMINATION

WEY HWANG WH-8001-220V PROGRAMMABLE COIL WINDING MACHINE W/ PEDAL AND PARTS (1) WEY HWANG WH-8001-220V PROGRAMMABLE COIL WINDING MACHINE (1) PEDAL (1) PARTS/ SCREWS/ BIT ENDS DIGITAL PROGRAMMABLE COIL WINDING MACHINE 200A/6000RPM 220V SPINDLES: 1 WIRE SIZE: 0.08~1.0MM SPREAD PITCH: 0~9.999MM SPREAD WIDTH: 100MM(MAX.) COIL DIAMETER: 110MM(MAX.) MAIN MOTOR: BRUSHLESS MOTOR SPREAD MOTOR: 2-PHASE STEPPING MOTOR MAX. SPEED: 6000RPM MEMORY: 999 STEPS POWER SOURCE: AC220V +/- 10%, 50/60 HZ WE POWERED THE COIL WINDING MACHINE ON AND SAW THE COILS SPINNING SMOOTHLY WHEN TESTED.

1996 YAMAZAKI MAZAK ULTRA550X CNC MACHINE MILL 80-PC-TOOL-HOLDER TOTE (1) YAMAZAKI MAZAK MAZATECH ULTRA550X CNC MACHINE MILL 80-PC-TOOL-HOLDER TOTE VIDEO (1) PARAMETER LIST FOR MAZATROL M PLUS (1) ALARM LIST FOR MAZATROL M PLUS (1) FUNCTION OF KEYS AND SWITCHES SHEETS (1) PROCEDURE BEFORE PERFORMING THE MACHINING SHEETS WT.: 33100 LBS. 3 PHASE 50/60 HZ 230VAC / 460VAC MAX. 175 / 87.8 A 80 PIECE TOOL HOLDER MAZATROL M PLUS CHIP-TOTE CONVEYOR: MANUFACTURER: MAYFRAN INTERNATIONAL SN: 96M4641 MAZAK CONTROL BOX: DATE: 1996 -04 MAIN CIRCUIT: 3 PHASE 200VAC 50/60 HZ CONTROL CIRCUIT: 100VAC 24VDC MAIN MOTOR: MAX. 21A 400 V SOME OF THE SHEETS OR LISTS MAY BE INCOMPLETE.

WEBER AUTOMATION W9000 TORQUE DRIVER CONTROL UNIT 110VAC 35W

YAMATO SCIENTIFIC COMPANY RE71 ROTARY EVAPORATOR WITH VERTICAL CONDENSER, FULL GLASSWARE (1) YAMATO RE71 EVAPORATOR (1) TRIPLE-SPIRAL VERTICAL CONDENSER (1) 10L EVAPORATOR FLASK (1) 5L CONDENSATE FLASK (1) SAMPLING VALVE (1) 3-WAY COCK VALVE MISCELLANEOUS CLAMPS/BOLTS &C. (1) BATH COVER (1) INSTRUCTION MANUAL (1) WRENCH MICROPROCESSOR CONTROLLER 10 LITERS EVAPORATOR FLASK 5 LITERS RECEIVING FLASK 20 LITERS HEATED BATH VERTICAL TRIPLE-SPIRAL CONDENSER ROTATION SPEED SETTING: UP TO 127 RPM TEMPERATURE SETTING: AMBIENT +5 TO 110OC 2.5KW BATH HEAT ELECTRIC LIFT HOLLOW-SPINDLE BRUSHLESS MOTOR POWER REQUIREMENT: 220V 50HZ 15A

WATLOW 965A-3CD0-00RG SERIES 965 100-240V AC/DC UNIVERSAL TEMPERATURE CONTROLLER (1) WATLOW 965A-3CD0-00RG SERIES 9 100-240VAC/DC UNIVERSAL TEMPERATURE CONTROLLER MANUFACTURER: WATLOW MODEL: 965A-3CD0-00RG DESCRIPTION: TEMPERATURE CONTROLLER LINE AND LOAD VOLTAGE: 100 TO 240V AC/DC MODE: ON/OFF, PID 5A RELAY MOUNT: 1/16 DIN THIS TEMPERATURE CONTROLLER WAS PULLED FROM WORKING EQUIPMENT AND

WATLOW RMGL-0404AA4AHB EZ-ZONE LVP GAS LINE TEMPERATURE CONTROLLER 24V W/ CABLES (1) WATLOW RMGL-0404AA4AHB EZ-ZONE LVP TEMPERATURE CONTROLLER (1) WATLOW P4107 INLINE CABLE ASSEMBLY (1) WATLOW P6 DC POWER CABLE ASSEMBLY DESCRIPTION: EZ-ZONE LVP TEMPERATURE CONTROLLER WITH CABLES (1) WATLOW RMGL-0404AA4AHB EZ-ZONE LVP TEMPERATURE CONTROLLER RMG - GAS LINE HEATER CONTROLLER L - LOW VOLTAGE 04 - 4 THERMOCOUPLE SENSORS 04 - 4 SUPERVISORY SENSORS AA - NO CONTROL LOOPS 4 - NUMBER OF OUTPUTS 20.4-30VAC/DC 50/60HZ 7 WATTS (1) WATLOW P6 DC POWER CABLE ASSEMBLY (1) WATLOW P4107 INLINE CABLE ASSEMBLY THIS TEMPERATURE CONTROLLER AND CABLE ASSEMBLIES WERE REMOVED FROM WORKING EQUIPMENT.

SOUTH BEND JOHNSON 80FW-AC OBI 80-TON PRESS 4"-STROKE SHUT-HT:15.5 ADJ:3.5 (1) SOUTH BEND JOHNSON 80FW-AC PRESS (1) JOHNSON OBI POWER PRESS OPERATION AND MAINTENANCE MANUAL (1) BARS/HARDWARE MANUFACTURER: SOUTH BEND JOHNSON PRESSES PRESS: 80FW-AC SN: 73105 OBI-80 TONNAGE: 80 STROKE: 4" SHUT HEIGHT: 15-1/2 ADJUSTMENT: 3-1/2 BED AREA, L-R, F-B: 36X24 RAM AREA, L-R, F-B: 16-1/4X13-1/2 MAX. ATTACHMENT WEIGHT: 525 STROKES/MIN 85 VOLTAGE: 230 HERTZ: 60 PHASE: 3 FULL LOAD CURRENT: 30 DISC. SW. INTERRUPT CAP.: 30 AMPS WIRING DIAGRAM NO.: ES2253 RESOLVER BASED PRESS CONTROL

[SONIX QUANTUM-350 SCANNING ACOUSTIC MICROSCOPE (C-SAM) SCANNING AREA: 350 X 350 MM SYSTEM NO. 3139-05 110 VOLTS SONIX QUANTUM 350 MICROSCOPE TRANSDUCERS (1) HARISONIC 12-2504-R 25MHZ .250" DIA. 15MM SPH.FOC. (1) PANAMETRICS-NDT V312 10MHZ 0.25" F=.75" PDF (1) PANAMETRICS V3815 110MHZ F=8MM (1) SONIX MS1C2506 25MHZ 5-15MM (1) SONIX MSIC-75M S-12 COMPUTER OR OTHER ACCESSORIES REQUIRED FOR OPERATION NOT INCLUDED

SOMARK MPA MARKING PRESSES PNEUMATIC HOT STAMPING PRESS DIGITAL TEMPERATURE CONTROL DIGITAL DWELL TIMER PRESSURE REGULATOR ON REAR INTERLOCKED WORK AREA 115VAC POWER OVERALL HEIGHT: 22" THROAT DEPTH, APPROXIMATE: 4.5" REQUIRE REPAIR OR SERVICE.

SOMACA SOMMER & MACA DBM-84 VERTICAL BELT SANDER 84"L X 2"W 3450-RPM 2-HP 1-PH (1) SOMACA SOMMER & MACA DBM-84 VERTICAL BELT SANDER 84"L X 2"W 3450-RPM 2-HP 1-PH. VERTICAL BELT: WIDTH: 2" LENGTH: 84" MOTOR: HP: 2 RPM: 3450 V: 115/208-230 SINGLE PHASE WHEN POWER WAS APPLIED, THIS ITEM RAN VERY SMOOTHLY. IT WAS NOT TESTED WITH A BELT. THE OTHER TWO PULLEYS NOT ATTACHED TO THE MOTOR MANUALLY SPUN EASILY WITHOUT PROBLEMS. THIS SANDER DOES NOT COME EQUIPPED WITH A BELT OR A NON-SLIP BAND (AS SHOWN, SEPARATED).

SENSATA TECHNOLOGIES QINEX CR-2604 CONTACT RESISTANCE TESTER VALIDATE INTEGRITY OF TEST SOCKETS AUTOMATICALLY MEASURES CONTACT RESISTANCE OF SPRING-LOADED CONTACTS/PINS IDENTIFY OPEN OR HIGH-RESISTANCE CONTACTS WITHIN YOUR ARRAY SUPPORTS HAND-HELD PROBE PEN FOR LOCALIZED PIN-POINT INSPECTION REQUIRES SOFTWARE (NOT INCLUDED) REQUIRES CUSTOM INTERFACE BOARD TO MEASURE YOUR SOCKETS (NOT INCLUDED) COMPATIBLE WITH BOARDS USED ON CR2600 AND CR2601

WATLOW 97A0-DAAU-00RG PROCESS TEMPERATURE CONTROLLER 100-240VAC 4.2"X2.05"X2.05" MANUFACTURER: WATLOW MODEL: 97A0-DAAU-00RG INDUSTRIAL PROCESS TEMPERATURE CONTROLLER POWER: 100-240VAC +10%, -15%; 50/60HZ, 5% OPERATING TEMPERATURE: 0-65 C DIMENSIONS: 4.2" X 2.05" X 2.05" CALIBRATION ACCURACY: +/-0.1% OF SPAN +/-1C ACCURACY SPAN: 540C/1000F MIN. COMMUNICATIONS: EIA/TIA-485, EIA/TIA-232, MODBUS RTU PROTOCOL DISPLAY: DUAL-4-DIGIT LED DISPLAYS RELAY: FORM C CONTACT CONFIGURATION THE CONTROLLER WAS REMOVED FROM A WORKING MACHINE.

SOMMER & MACA SOMACA X-Y 60 X 60 GLASS CUTTER 60"X60" SUCTION SYSTEM 152"-LENGTH S/N: 63613 BLACK TABLE DIMS: 60" X 60" OVERALL TRACK LENGTH: 152" APPROX. MOVE TABLE: CHAIN GLASS/TABLE SUCTION SYSTEM(SMALL HOLES IN BLACK TABLE) WHEN POWER WAS APPLIED, THIS ITEM RAN VERY SMOOTHLY. THE THREE MOTORS CONTROLLING THE CUTTING CYLINDER DIRECTIONS, TABLE MOVEMENT AND SUCTION SYSTEM ALL FUNCTIONED PROPERLY WITH NO PROBLEMS. THE CUTTING CYLINDER AND TABLE MOVED BACK AND FORTH AND IT HAD GOOD SUCTION.

SEALANT EQUIPMENT ENGINEERING INC. PROGRAM-A-SHOT 997 MATERIAL DISPENSING SYSTEM. PART NUMBER: 2200-1000-001. MATERIAL DISPENSING SYSTEM MEDIUM: 2-COMPONENT SILICONE, EPOXY, OR URETHANE FOR POTTING OR ENCAPSULATION APPLICATIONS. POWER: 480VAC SUPPLY VOLTAGE. PHASE: 3. FREQUENCY: 60 HZ. DISPENSING VALVE: 2150-221-006, 3500PSI, BAYONET OUTLET PORT. RESIN CHAMBER DIMENSIONS: . CONTROL PANEL: ALLEN BRADLEY PANELVIEW 1000 MODEL: 2711-T10C10. VOLTAGE: 100-240VAC 50/60 HZ. CURRENT RATING: 0.8-0.4A 100VA. CPU: SLC 5/05 DEVICENET. POWER SUPPLY TRANSFORMER: EGS TYPE HS HEVI-DUTY MODEL: HS5F5AS. PRIMARY VOLTAGE: 240/480. SECONDARY: 120/240. FREQUENCY: 60 HZ. SINGLE PHASE 5.0 KVA 180 INSULATION CLASS. THE MACHINES WERE REMOVED FROM A WORKING MANUFACTURING ENVIRONMENT. THE CPU AND CONTROL PANELS POWER ON, AS SHOWN IN THE PHOTOS. AN AIR SUPPLY HOSE WAS USED TO TEST AIRFLOW IN THE PNEUMATIC COMPONENTS. THE POWER SUPPLY OUTPUT VOLTAGES WERE TESTED AND OBSERVED TO BE AT PROPER LEVELS.

SCHMIDT 420 SERVOPRESS FORCE:7,870LBS DRIVE:ROLLER-SCREW 400VAC 3PH STROKE:400MM FORCE F: 7,870 MAX. LBS. ( KN) FORCE F AT 100% DUTY CYCLE: 4,500 LBS. (50 KN) RAM STROKE: 400 / 15.74 MM / LBS RESOLUTION (DRIVE CONTROL): < 0.0004" RAM SPEED: 0 - 7.87"/SEC OVERLOAD PROTECTION: MECH. CLUTCH DRIVE: ROLLER SCREW POWER SUPPLY: 400V 3-PH 16A RAM: EXTERNAL RAM DIMENSIONS: 2.16" X 2.16" RAM BORE (WITH BUSHING): 20H7 0 MM TOP WORKING POSITION: 2.36" TOP RAM POSITION: 1.77" FRAME: THROAT DEPTH: 6.29"

SCANNER TECHNOLOGIES UP1085 ULTRAVIM PLUS INSPECTION CAMERA + ILLUMINATORS (1) STC UP 1085 INSPECTION CAMERA (2) ILLUMINATOR MODULES AS SHOWN (1) GLASS PLATE WITH SQUARES GRID AS SHOWN

2015 SEIKO EPSON CORPORATION G3-351CM SCARA ROBOT WITH RC700-A CONTROLLER AND TP BYPASS PLUG (1) EPSON RC700-A (1) EPSON G3-351CM ROBOT ARM (1) TP BYPASS PLUG G3-SERIES ROBOTIC MANIPULATOR HIGH-SPEED, HIGH-ACCURACY, SPACE-SAVING SAME SIZE OF MOTION RANGE AS OTHER BRANDS' ONE UP ROBOTS ARM LENGTH: 350 MM JOINT 3 (Z-AXIS) STROKE: 120 MM CLEANROOM AND ESD/ANTI-STATIC VERSION MULTIPLE MOUNTING VERSION (NOT LIMITED TO TABLETOP MOUNTING) PAYLOAD: RATED 1 KG, MAXIMUM 3 KG MOTOR POWER: AXIS 1: 200 W AXIS 2: 150 W AXIS 3: 150 W AXIS 4: 150 W MAXIMUM OPERATING SPEED: JOINT 1: 4350 MM/S JOINT 2: 4350 MM/S JOINT 3: 1100 MM/S JOINT 4: 3000 DEG/S MAXIMUM MOTION RANGE: JOINT 1: +/- 120 MM JOINT 2: +/- 142 MM JOINT 3: 120 MM JOINT 4: +/- 360 O JOINT 3 DOWN FORCE: 150 N REPEATABILITY: +/-0.01 MM JOINTS 1, 2, 3, +/-0.005 DEG JOINT 4 AC SERVO MOTORS ALL AXES, JOINT 3 BRAKE RELEASE BUTTON WITH ELECTRICAL AND PNEUMATIC FEEDTHROUGH FOR CUSTOMER USE MODEL RC700-A ROBOT CONTROLLER POWER REQUIREMENT: 200-240 V 1PHASE 50/60 HZ WINDOWS EMBEDDED CE 6.0 CORE COMPATIBLE WITH TEACH PENDANTS TP1, TP2, OR TP3 (NOT INCLUDED) REQUIRES PC WITH WINDOWS AND CONTROL SOFTWARE (NOT INCLUDED)

2015 EPILOG 8000 MINI 50 WATT LASER ENGRAVER W/ 24" X 12" HONEYCOMB BED ROTARY (1) ROTARY ENGRAVING ATTACHMENT (1) LASER ALIGNMENT TARGET (1) LASER FOCUSING BRACKET (1) POWER CABLE (1) ETHERNET CROSSOVER CABLE (1) SOFTWARE DISC 24X12" WORKING AREA 5" MAXIMUM MATERIAL THICKNESS 50 WATTS LASER CONNECT TO YOUR PC BY USB OR ETHERNET POWER REQUIREMENT: 100-240V 47-63HZ 15A COMPRESSED AIR IS REQUIRED FOR THE AIR-ASSISTED BLOW-OFF FEATURE METAL HONEYCOMB MESH CUTTING BED CLEAR GLASS WIDE-OPENING TOP FOLD-DOWN FRONT-LOADING DOOR SAFETY INTERLOCKS ON DOORS REAR-PANEL VENTILATION PORT MANUFACTURED: 2015 (LASER TUBE: 2013)

EFD NORDSON 1500XL METERED FLUID DISPENSING DOSING UNIT W/ FOOT PEDAL. ADHESIVE FLUID DISPENSER. POWER: 100/120/220 VAC 50/60 HZ 14/12 VA. CYCLE RATE: >600/MINUTE. TIME CONTROL: MICROPROCESSOR WITH 0.00005 SECOND REPEATABILITY. TIME RANGE: PROGRAMMABLE 0.001 TO 99.9 SECONDS. INITIATION: MOMENTARY. AIR INPUT: 80 TO 100 PSI (5.5 TO 6.9 BAR). AIR OUTPUT: 0 TO 100 PSI (0 TO 6.9 BAR). FOOT SWITCH: PART NUMBER: 2015A. VOLTAGE: 5.5VDC. WORKING WHEN REMOVED FROM SERVICE.

ETS-LINDGREN HATS ACOUSTIC ENCLOSURE ANECHOIC CHAMBER 36" ID (1) ETS-LINDGREN HEAD AND TORSO TEST (HATS) ACOUSTIC ENCLOSURE (1) SLIDE-OUT ACCESS TRAY OVERALL DIMENSIONS: 57" L X 56" W X 78 3/4" H (W/O CASTERS) (4) 3" CASTERS OVERALL HEIGHT W/ CASTERS 81.5" 39" X 30" DOOR OPENING INSIDE: 36" X 36" X 42" 5" THICK ACOUSTIC FOAM 2,500 LBS SLIDE-OUT ACCESS TRAY DIMMS: 44" X 23" X 7" (TABLE TOP IS 33" LONG) WE CONFIRMED THE MECHANICAL FUNCTIONALITY OF THE DOOR, HANDLE, LATCHES, AND CASTER WHEELS FUNCTIONED AS DESIGNED.

ETS 5532 LABORATORY INTEGRATED ENVIRONMENTAL CONTROLLED CHAMBER/GLOVE BOX (1) ETS 5532 LARGE LABORATORY INTEGRATED CONTROLLED ENVIRONMENTAL CHAMBER/GLOVE BOX (1) SOLID FRONT DOOR (1) OPERATING MANUAL MANUFACTURER: ETS ELECTRO-TECH SYSTEMS MODEL: 5532 DESCRIPTION: CONTROLLED ENVIRONMENTAL CHAMBER/GLOVE BOX DIMENSIONS: INTERNAL: 38.75 W X 20 D X 21 H (98CM X 51XM X 53XM) EXTERNAL: 52 W X 25 D X 22 H (132CM X 64CM X 56CM) MATERIAL: 3/8 INCH CLEAR & WHITE ACRYLIC GLOVES: .018 (0.5MM) LATEX, 6 (15CM) PORTS RH/ TEMPERATURE SENSOR ACCURACY: RH: 2.0% RH AT 68F (20C) AND 0-90% RH , 3.0% RH AT 68F (20C) AND 90-100% RH TEMP: 0.4 F ( 0.2 C) AT 20C POWER: VOLTAGE: 115/230 VAC 50/60HZ CURRENT: 8AMP/4AMPS DUAL MICROPROCESSOR PID CONTROLLERS CONTROLLERS: TWO (2) CAL 9500, MULTIPLE RAMP/SOAK CYCLES, RESOLUTION: 0.1%/0.1 INTEGRATED INTERNAL LIGHTING INTEGRATED GFIC AC POWER OUTLET TWO DOORS WITH 12-TURN LATCHES FRONT DOOR OPENING: 32X14 (8136 CM) SIDE DOOR OPENING: 14X4 (3610 CM) STANDARD 1.5 DIA. CABLE PASS-THROUGH, HOSE BARBS & COMPRESSION FITTINGS POWER WAS APPLIED TO THIS CHAMBER AND THE LIGHT, FAN, TEMPERATURE CONTROLLER, AND HUMIDITY CONTROLLER WERE ALL TESTED AND OPERATED AS INTENDED.

EFD NORDSON 1500XL-15 METERED FLUID DISPENSING DOSING UNIT ADHESIVE FLUID DISPENSER. POWER: 100/120/220 VAC 50/60 HZ 14/12 VA CYCLE RATE: >600/MINUTE TIME CONTROL: MICROPROCESSOR WITH 0.00005-SECOND REPEATABILITY TIME RANGE: PROGRAMMABLE 0.001 TO 99.9 SECONDS INITIATION: MOMENTARY AIR INPUT: 80 TO 100 PSI (5.5 TO 6.9 BAR) AIR OUTPUT: 0 TO 100 PSI (0 TO 6.9 BAR)

2013 EDWARDS/TEMESCAL VES-2550 E-BEAM EVAPORATOR 3-PHASE 208V CV-6SLX (S/N: 6024-7110-0) (1) E-BEAM EVAPORATOR (2) EQUIPMENT RACKS (1) ROUGH PUMP (1) CTI 10 CRYO-TORR CRYO PUMP (NO COMPRESSOR) (1) PARTIAL MANUAL POWER REQUIREMENT: 208V/70A THREE PHASE 3 STATION BEAM TEMESCAL SOURCE: TWO HEARTHS WITH A SINGLE LARGE CRUCIBLE EACH AND ONE HEARTH WITH A FOUR POSITION ROTATABLE CRUCIBLE. ALL HEARTHS ARE TEMESCAL. TEMESCAL CV-6SLX POWER SUPPLY MANUFACTURED 2013 TEMESCAL FERROTEC TEM E BEAM CONTROLLER WITH PENDANT CONTROL CTI CRYO-TORR 10 VACUUM PUMP WITH REBUILT LEYBOLD D65B ROUGH PUMP. TEMESCAL VERSAVAC 5 VACUUM GAUGE WITH INPUTS FOR 5 T/C GAUGE SENSORS AND TWO ION GAUGES TEMESCAL AUTO PUMP CONTROL WITH VACUUM SYSTEM STATUS DISPLAY SHUTTER CONTROL SUBSTRATE ROTATOR CONTROL TEMESCAL MC-4C MOTOR CONTROL CTI CRYOGENICS TEMPERATURE INDICATOR WITH REGENERATION TIMER TEMESCAL TURRET SOURCE SELECTOR FOR THE 4 POSITION HEARTH THE SECOND RACK HOUSES THE SUBSTRATE HEATER WITH TRANSFORMERS AND PID CONTROL, AS WELL AS CURRENT INDICATORS. FILAMENT ASSEMBLIES ARE MISSING FROM THE TWO LARGE CRUCIBLES. THE CONDITION OF THE FILAMENT ASSEMBLY ON THE FOUR POSITION HEARTH IS UNKNOWN. HEARTH POSITIONS ARE LABELED NICKEL, ALUMINUM, AND MAGNESIUM FLUORIDE. THE SYSTEM WAS USED FOR OPTICAL COATINGS. THE SUBSTRATE HOLDER AND SHUTTERS ARE MISSING AND THERE IS NO HELIUM COMPRESSOR. PLEASE NOTE: NO CHILLER OR HELIUM COMPRESSOR IS INCLUDED.

EDWARDS SPECTRON 600D HELIUM LEAK DETECTOR HAS BOTH TURBO PUMPS (1) EDWARDS 600D HELIUM LEAK DETECTOR MANUFACTURER: EDWARDS HIGH VACUUM INTERNATIONAL MODEL: SPECTRON 600D P/N: D155-04-000 HELIUM LEAK DETECTOR MISSING THE ROUGHING DIAPHRAGM PUMP MISSING AT LEAST ONE SENSOR BAD MOTHERBOARD BOC EDWARDS B722-01-000 TURBOMOLECULAR PUMP INCLUDED ALCATEL MDP5011 TURBO PUMP INCLUDED POWER: 115V 60HZ 10A INCOMPLETE, ! REQUIRES SERVICE.

MKS INSTRUMENTS ASTEX FI20110 SMARTPOWER 6.0KW GENERATOR, INVERTER 2.7C UPGRADED (1) MKS FI20110 6KW POWER GENERATOR MANUFACTURER: MKS INSTRUMENTS ASTEX MODEL: FI20110 SMARTPOWER MICROWAVE PLASMA POWER SOURCE INTELLIGENT POWER GENERATOR WATER-COOLED POWER: 200-208V 3PHASE 50/60HZ THIS UNIT IS IN GOOD WORKING CONDITION. IT WAS A SPARE FOR A SYSTEM BUILDER WHO DIDN'T NEED IT ANY MORE.

MKS ASTRONHF-S REACTIVE GAS PLASMA GENERATOR HEAD ONLY AX7645 (1) MKS AX7645RH-10 REACTIVE GAS GENERATOR (PLASMA SECTION) MANUFACTURER: MKS (ASTEX PRODUCTS) MODEL: ASTRONHF-S REACTIVE GAS GENERATOR P/N: AX7645RH-10 REV. C HIGHER FLOW VARIANT BROAD OPERATING RANGE, UP TO 15 SLM NF3 AND HIGH FLOWS OF OTHER GASES COMPACT, LID-MOUNTABLE PLASMA SECTION (REQUIRES RACK-MOUNTED POWER SUPPLY, NOT INCLUDED) CLOSE COUPLING OF PLASMA SECTION IMPROVES EFFICIENCY NO ARGON REQUIRED DURING OPERATION (ONLY REQUIRED DURING PLASMA INITIATION) HIGH DISSOCIATION RATE OVER BROAD PRESSURE RANGE FOR ROBUST OPERATION COMPATIBLE WITH 200MM AND 300MM CHAMBERS SUITABLE FOR CONTINUOUS OPERATION WATER-COOLED THIS UNIT IS IN GOOD WORKING CONDITION. WE GOT IT FROM A SYSTEM BUILDER WHO TESTED IT AND SET IT ASIDE AS A SPARE.

MKS 626B13TBE BARATRON CDG VACUUM GAUGE MANOMETER 0-10VOUT 8VCR +/-15V (1) MKS 626B BARATRON VACUUM GAUGE MANUFACTURER: MKS MODEL: 626B13TBE BARATRON 626B-SERIES CAPACITANCE MANOMETER FULL SCALE: 1000 TORR UNHEATED ACCURACY: 0.25% OF READING OUTPUT: 0-10VDC POWER: +/-15VDC 15-PIN DSUB CONNECTOR 1/2" 8VCR GAS FITTING OUTPUT SIGNAL IS LINEAR WITH PRESSURE VERY FAST RESPONSE LOW HYSTERESIS EXCELLENT REPEATABILITY VERY HIGH RESOLUTION (TO 0.001%FS) EXCEPTIONALLY HIGH CORROSION RESISTANCE CAN WITHSTAND REPEATED EXPOSURES TO 3.1 BAR WITHOUT DEGRADATION THIS WAS REMOVED FROM A WORKING TEST STATION.

MKS 151-0040K HPS KF-40 NW40 RIGHT ANGLE MANUAL VACUUM VALVE (1) MKS 151-0040K RIGHT ANGLE MANUAL VACUUM VALVE MANUFACTURER: MKS MODEL: 151-0040K TYPE: RIGHT ANGLE VALVE THIS VALVE WAS REMOVED FROM A WORKING ENVIRONMENT.

MITUTOYO M PLAN APO SL 100X /0.55 F=200 MICROSCOPE (1) MITUTOYO 100X OBJECTIVE LENS MANUFACTURER: MITUTOYO MICROSCOPE OBJECTIVE LENS MAGNIFICATION: 100X SUPER LONG WORKING DISTANCE M PLAN APO OPTICS N.A.: 0.55 /0 INFINITY CORRECTED, FOR USE WITHOUT COVER SLIPS F=200 M26 MOUNTING THREADS THIS LENS IS IN GOOD WORKING CONDITION. WE FITTED IT TO A MICROSCOPE AND FOUND THAT THE BLEMISH IN THE PRIMARY LENS IS NOT VISIBLE AT ALL IN THE FIELD OF VIEW. THE VIEW WAS CLEAR;

MITUTOYO 30CM STAINLESS STEEL HARDENED UPRIGHT HEIGHT GAUGE ~20.75" TOTAL HEIGHT (1) MITUTOYO 30CM STAINLESS HARDENED UPRIGHT HEIGHT GAUGE ~20.75" TOTAL HEIGHT ADJUSTABLE HEIGHT GAUGE 30CM CONSTRUCTION: STEEL, STAINLESS HARDENED UNIT TOTAL HEIGHT: ~20.75" BASE DIMENSIONS: 5.75"L X 3.75"W X 1.75"H INCREMENTS: 1MM MADE IN JAPAN THE GAUGE WAS REMOVED FROM A WORKING ENVIRONMENT.

MICROMANIPULATOR FET PS4 PROBE POWER SUPPLY 4 CHANNELS ADJUSTABLE ZERO (1) MICROMANIPULATOR FETPS4 POWER SUPPLY MANUFACTURER: THE MICROMANIPULATOR COMPANY, INCORPORATED MODEL: FET PS 4 FET PROBE POWER SUPPLY (4) CHANNELS ADJUSTABLE ZERO ALL CHANNELS THIS UNIT POWERS ON;

MKS 162-0040K HIGH VACUUM BELLOWS SEALED 1.5" NW40 ISOLATION ANGLE VALVE 304SS (1) MKS 162-0040K HIGH VACUUM BELLOWS SEALED VALVE MANUFACTURER: MKS MODEL: 162-0040K DESCRIPTION: HIGH VACUUM BELLOWS SEALED ISOLATION ANGLE VALVE VACUUM RANGE: 15 PSIG TO 1.0 X 10-9 TORR PORT SIZE: 1.5" FLANGE SIZE: NW40 ACTUATION: PNEUMATIC FLANGE TYPE: ISO-KF BODY MATERIAL: 304 STAINLESS STEEL THIS VALVE WAS PULLED FROM A WORKING SETUP THAT WAS BEING WORKING.

MITUTOYO IDC-112E DIGIMATIC INDICATOR GAUGE 0-.5IN/12.7MM (1) MITUTOYO IDC-112E CODE 543-142 0-.5IN/12.7MM DIGIMATIC INDICATOR GAUGE MANUFACTURER: MITUTOYO MODEL: IDC-112E DESCRIPTION: DIGIMATIC INDICATOR GAUGE MEASURING RANGE: 0-12.7MM (0-0.5 INCHES) RESOLUTION: 0.001MM (0.00005 INCHES) ACCURACY: 0.003MM (0.00012 INCHES) REPEATABILITY: 0.001MM (0.00005 INCHES) DISPLAY: LCD WITH 6-DIGIT DISPLAY FUNCTIONS: ABSOLUTE AND INCREMENTAL MODE TOLERANCE JUDGMENT PRESET DATA HOLD DATA OUTPUT BATTERY: SR44 SILVER OXIDE BATTERY (NOT INCLUDED) PROTECTION LEVEL: IP42 (DUST AND WATER RESISTANT) MEASURING FORCE: 1.5N OR LESS WITH IN-HOUSE BATTERIES (NOT INCLUDED) WE TURNED THIS INDICATOR ON AND TESTED IT WITH A THICKNESS GAUGE AND IT MEASURED CORRECTLY.

MITUTOYO CD-15R DIGIMATIC DIGITAL CALIPER 150MM/5.9" +/-0.0015" ACCURACY. MANUFACTURER: MITUTOYO MODEL: CD-15R PART NUMBER: 500-227-50 DIGITAL CALIPER SERIES: DIGIMATIC RANGE: 150 MM ACCURACY: +/-0.0015" RESOLUTION: 0.01 MM REPEATABILITY: 0.01 MM MADE IN JAPAN THE CALIPER WAS REMOVED FROM A WORKING ENVIRONMENT. THE CALIPER WAS TESTED AND MEASURED ACCURATELY AS INTENDED.

VWR SCIENTIFIC PRODUCTS 210 4-1/8" X 5-3/8" TOP PLATE 371C MAX MINI HOT PLATE. LINE VOLTAGE: 115VAC. CAST ALUMINUM TOP PLATE. PLATE DIMENSIONS: 4-1/8" X 5-3/8". LED HEAT INDICATOR. POWER CONSUMPTION: 325W. LINE FREQUENCY: 50/60HZ. MAX TEMPERATURE: 371C. CAPACITY: 2L OF LIQUID.

NEW STAINLESS STEEL 38"W X 100'L CONVEYOR BELT FOOD GRADE FDA MESH WIRE (1) NEW REXNORD/CAMBRIDGE CAMBRI-LINK STAINLESS STEEL 38" X 100' STANDARD RADIUS BELT MANUFACTURER: CAMBRIDGE INTERNATIONAL MODEL: STANDARD RADIUS CAMBRI-LINK P/N: WRSS-38-OSD|31 DESCRIPTION: FLAT WIRE STYLE CONVEYOR BELT MATERIAL: WEAR RESISTANT STAINLESS STEEL (WRSS) 53 OPENINGS ACROSS WIDTH FURNISHED WITH DOUBLE REINFORCING BARS ON BOTH EDGES WIDTH: 38" (965MM) LENGTH: 100 FT. MESH SIZE: 1/2 X 1 (12.7 X 25.4 MM) BELT PITCH: 1" (25.4 MM) STRAIGHT RUNNING TENSION LIMIT: 1,700 LBS./FT (2,530 KG/M) TURN OR SPIRAL TENSION LIMIT: 200 LBS./FT (297 KG/M) BELT INSIDE TURNING RADIUS: 83.6 DEGREES FLAT STRIP: EXTRA HEAVY DUTY: 1/2 X .0625 (12.7 X 1.59 MM) RODS: EXTRA HEAVY DUTY: 6 GAUGE 0.192 (4.9 MM) DIAMETER

VIBROMATIC V-600-8727 VIBRATORY BOWL FEEDER WITH BULK HOPPER H002 DRIVE CONTROL 8727 (1) VIBRATORY BOWL FEEDER WITH BULK HOPPER AND ADJUSTABLE-SPEED DRIVE CONTROLLER 10" BOWL SIZE VERY HEAVY TABLE, APPROXIMATELY 22" X 18" X 1.25" THICK STEEL PLATE ADJUSTABLE SPEED VIBRATORY FEEDER: 10" BOWL MADE FOR FEEDING A 1/2" DIAMETER, VERY THIN NUT VIBROMATIC SELLS NEW/CUSTOM BOWLS FOR YOUR APPLICATION IF NECESSARY AUTOMATICALLY SHUTS OFF IF THE OUTFEED CHUTE IS BLOCKED DRIVE UNIT APPEARS TO BE WLPS-9 TYPE 2 ELECTROMAGNETIC COILS USES BANNER Q45VR3FQ TO SENSE CHUTE OBSTRUCTIONS BULK HOPPER FEED FROM YOUR BULK SOURCE WHEN YOU NEED MORE PARTS THAN FEEDER CAN HOLD LEVEL CONTROL STOPS HOPPER WHEN FEEDER HAS ACCEPTABLE LEVEL OF PARTS DROPS PARTS ONTO SOFT SHEET, NOT HARD BOWL USES BANNER Q60VR3AFV1000Q1 FOR LEVEL SENSING IN THE BOWL CONTROLLER MODEL H002 INDEPENDENT POWER AND SPEED CONTROLS FOR HOPPER AND FEEDER REPLACES 2G-1R AND 2G-2R 120VAC POWER THIS IS IN GOOD WORKING CONDITION. THE BOWL AND HOPPER BOTH VIBRATE ACCORDING TO THE SPEED SET ON THE CONTROLLER. WHEN EITHER SENSOR IS OBSTRUCTED, THE CORRESPONDING ELECTROMAGNET DRIVES STOP FEEDING.

VERITY SD1024 SMART SPECTROGRAPH 1004104 AC POWER , GOOD FANS & DISPLAY

2003 VACUUM INSTRUMENT COMPANY MS50HS CONSOLE HELIUM LEAK DETECTOR 120V 1P (1) VIC MS50HS CONSOLE HELIUM LEAK DETECTOR (1) POWER CORD (1) PUMPS: ALCATEL 2021 ROUGH PUMP, ALCATEL 2008 FORELINE PUMP, TURBOMOLECULAR HIGH VACUUM PUMP, LN2 RESERVOIR TEST PORT: COMPRESSION FITTING 1-1/8" OPERATING HOURS: 67,000 THIS IS A WET-PUMPED LEAK DETECTOR. THE FORELINE PUMP ACHIEVES 6MT INTO A VACUUM GAUGE. THE ROUGH PUMP ACHIEVES 8MT INTO BLANK TEST PORT. BOTH TEST PORT AND FORELINE GAUGES WERE CALIBRATED. CABINET AIR FILTERS WERE CLEANED. PUMP OIL WAS CHANGED; THE OIL IS TW (TECHNICAL WHITE.) AUTOTUNE RUNS SUCCESSFULLY. IF YOUR APPLICATION REQUIRES A CALIBRATED LEAK THEN YOU WILL NEED TO SEND IT IN FOR CALIBRATION. HIVAC WAS 7E-5 TORR.

VWR 1365DP-2 DEPRYOGENATION OVEN MECHANICAL CONVECTION 5 CU.FT. 260C SHELDON VWR 1365DP-2 OVEN MANUFACTURER: SHELDON (FOR VWR) MODEL: 1365DP-2 PART NO.: 9070908 LABORATORY OVEN MECHANICAL HORIZONTAL CONVECTION EXTERIOR DIMENSIONS: 31.5" X 25.5" X 35"H INTERIOR DIMENSIONS: 23" X 21" X 18"H STAINLESS STEEL INTERIOR CAPACITY: 5 CUBIC FEET AIR FLOW: 144 LFM (EXHAUST CLOSED) TEMPERATURE RANGE: 40 TO 260 OC SPECIALLY DESIGNED FOR DEPRYOGENATION, LOOKS LIKE A GENERAL PURPOSE OVEN THOUGH (?) MICROPROCESSOR CONTROLLED LED TIMER FOR UP TO 99H59M COUNTS DOWN AND CUTS HEAT AT END OF RUN ADJUSTABLE OVERTEMPERATURE SAFETY POWER: 230V 1PHASE 60HZ 9A THIS OVEN IS IN GOOD WORKING CONDITION. VERIFIED IT WILL HOLD STEADY AT A SETPOINT AT 270. THE INTERNAL FAN BLOWS A STRONG CURRENT IN THE CHAMBER. THE DOOR LATCHES SECURELY. THE TIMER COUNTS DOWN.

VWR 1330FM 1.6 CU.FT. HORIZONTAL CONVECTION LABORATORY OVEN 120V DIGITAL HAFO (1) VWR 1330FM OVEN MANUFACTURER: SHELDON MFG (FOR VWR SCIENTIFIC) MODEL: 1330FM P/N: 9071047 FORCED CONVECTION OVEN (HORIZONTAL AIR FLOW HAFO) TEMPERATURE RANGE: ABOVE AMBIENT 40O TO 240OC (SEE NOTES) INTERIOR DIMENSIONS: 13" X 14" X 14.75 (1.6 CUBIC FEET) EXTERIOR DIMENSIONS: 21.25" X 23.75" X 33" DIGITAL (MICROPROCESSOR) CONTROLS, PUSHBUTTON OPERATION ADJUSTABLE LATCH AND HINGES 3"ADJUSTABLE EXHAUST PORT WRAPAROUND INSULATION DIGITAL TIMER POWER: 120V 60HZ 12A WORKING AND FULLY OPERATIONAL

SANDUSKY STEEL STORAGE CABINET BEIGE 2-DOOR 3-SHELF 36"W X 18"D X 78"H

CUSTOM POWER FOOD-GRADE PROCESSING CONVEYOR STAINLESS STEEL TILT 1/2-HP + (1) CUSTOM POWER FOOD-GRADE PROCESSING CONVEYOR STAINLESS STEEL TILT 1/2-HP + CONVEYOR: MANUFACTURER: UNKNOWN MODEL: UNKNOWN CUSTOM CONVEYOR CONVEYOR LENGTH (APPROX.): 5 FT TILT: HORIZONTAL TO 30 (APPROX.) WHITE PLASTIC ROLLERS: WIDTH: 6" MOTOR: MANUFACTURER: SEW EURODRIVE S37 DRS71S4/DH 87.7417262201.0001.17.10 V: 230 / 460 A: 1.84 / 0.92 DUTY: S1 60 HZ 3 PHASE RPM: 1700/20 CT: 300-1800 RPM IP66 TEFC REDUCER: MANUFACTURER: SEW EURODRIVE S37 DRS71S4/DH 87.7417262201.0001.17.10 I = 86.36 NA RPM 20 NE RPM 1700 MA MAX LB-IN 725 MTG POS M1A

HEAVY STEEL 17' X 6' RAISED FLOOR RAMP ELEVATED W/TILES AND HARDWARE SERVER ROOM (24.5) RAISED FLOOR TILES (1) METAL RAMP (1) 24" X 17' RUBBER MAT (1) 48" X 17' RUBBER MAT (1) ASSORTED HARDWARE TILES: 24.5 TILES SQUARE FOOTAGE: 98 SQ/FT DIMENSIONS: 24 X 24 X 1 3/8 APPLICATIONS: INDUSTRIAL FLOORING MATERIAL: STEEL AND CONCRETE BASE COLOR: DARK GRAY TOP COLOR: PALE GREEN/ TAN TILE WEIGHT: 30.63 PER TILE MAT LENGTH: SMALLER MAT: 24" X 17' LARGER MAT: 48" X 17' COMPLETE RAMP DIMENSIONS: 17 FT. X 6 FT

SANDUSKY 2-DOOR STORAGE CABINET 3-SHELF BEIGE 30" W X 18" D X 72" H

2007 SAMICK THK WTR3I15 WAFER TRANSFER HANDLER ROBOT MODULE (1) SAMICK WTR3I15 SYSTEM MANUFACTURER: SAMICK THK MODEL: WTR3I15 MECHATRO SYSTEM SMART SERIES WAFER TRANSFER ROBOT EXTENDS ARM IN STRAIGHT LINE TOP ROTATES THROUGH NEARLY A FULL CIRCLE TOP RISES/FALLS IN STRAIGHT LINE POWER: 220-240V 50/60HZ 20A DIMENSIONS: 18.5" X 17.5" X 19", 160LBS. MANUFACTURE DATE: 2007.02.12

RYOBI P500 18V ONE+ 5 1/2" CIRCULAR SAWS W/LASER ALIGNMENT (2) RYOBI P500 18VOLT ONE+ 5 1/2" CIRCULAR SAWS W/LASER ALIGNMENT MANUFACTURER: RYOBI MODEL: P500 CORDLESS CIRCULAR SAW INTEGRATED LASER ALIGNMENT SYSTEM BLADE TYPE COMPATIBILITY: 5 1/2" BATTERY: 18V (NOT INCLUDED) ARBOR SIZE: 10MM SPEED: 4200 RPM NO LOAD SPEED CUT CAPACITY: 90 DEGREES: 1 9/16", 45 DEGREES: 1 1/8" IN-LINE HANDLE DESIGN THE UNITS DO NOT INCLUDE BATTERIES OR SAW BLADES.