Lumber Processing Mass Timber Equipment Unused LikeNew Assets

CONCEPTION RP TIMBER FINGER JOINTER AND GRADE LINE, LIGHTLY USED. FULL LINE MANUFACTURED BY CONCEPTION RP - FINGER JOINTER/SHAPER, TONG LOADER, CROWDER - (2) CROSS CUT SAWS, TRIM SAWS, (5) PET SAWS - TILT HOIST, UNSCRAMBLER, ACCUMULATION CONVEYORS - OUTFEED STRAPPING MACHINE/BANDER, STACKER, - ACCESS PLATFORMS AND CATWALKS - SCANWOOD SCANNER, MOISTURE DETECTOR/SCANNER - A LONG LIST OF SPARE PARTS, QA/QC TESTING TABLE - SAFETY FENCING, GATES, AND INTERLOCKS - CONTROLLERS, HMIS, CABLING - CURING TABLES, GUIDE TUNNEL, AND CURING ZONES - FLYING SAW - INFEED/OUTFEED ROLLS/CHAINS, REJECT GATES

2023 USNR ELECTRATONG LUG LOADER, NEW, NEVER USED. DRIVE CALCULATIONS MACHINE DESCRIPTION: LUG LOADER JACKSHAFT PEAK MOTOR RPM: 3750 RPM OPERATING RPM: 150 RPM REDUCER RATIO: 25.00 : 1 REDUCER OUTPUT RPM: 150 RPM TONG SHAFT RPM: 150 RPM. LUG LOADER OUTFEED BELTS PEAK MOTOR RPM: 3750 RPM OPERATING RPM: 150 RPM REDUCER RATIO: 25.00 : 1 REDUCER OUTPUT RPM: 150 RPM TONG SHAFT RPM: 150 RPM. TONG SHAFT 1, 2, 3 PEAK MOTOR RPM: 3750 RPM OPERATING RPM: 150 RPM REDUCER RATIO: 25.00 : 1 REDUCER OUTPUT RPM: 150.0 RPM TONG SHAFT RPM: 150.0 RPM. TONG SHAFT 4, 5 DRIVEN FROM: LUG LOADER JACKSHAFT DRIVEN FROM RPM: 150 RPM DRIVEN FROM SPROCKET: 45 TEETH HEAD SHAFT DRIVEN SPROCKET: 20 TEETH HEADSHAFT RPM: 157.5 RPM HEAD PULLEY DIAMETER: 6.5 INCH BELT SPEED: 268.0 FPM. TONG SHAFT 6, 7, 8 PEAK MOTOR RPM: 3750 RPM OPERATING RPM: 150 RPM REDUCER RATIO: 25.00 : 1 REDUCER OUTPUT RPM: 150.0 RPM TONG SHAFT RPM: 150.0 RPM.

2023 USNR MULTI-TRACK FENCE 8P RH 24, FENCE VERIFICATION SYSTEM, NEW, NEVER USED. DRIVE CALCULATIONS: MACHINE DESCRIPTION: MULTI-TRACK FENCE DRIVEN FROM POSITIONING TRANSFER SHAFT DRIVEN FROM HEADSHAFT 80 RPM REDUCER OUTPUT SPROCKET 21 TEETH HEAD SHAFT DRIVEN SPROCKET 36 TEETH HEAD SHAFT RPM 46.67 RPM HEAD SHAFT SPROCKET 24 TEETH LUG SPACING 8 PITCHES LUG RATE 140 LPM. MACHINE DESCRIPTION: MULTI-TRACK FENCE ENCODER DRIVEN FROM FENCE HEAD SHAFT DRIVEN FROM RPM 46.67 RPM DRIVEN FROM SPROCKET 60 TEETH ENCODER DRIVEN SPROCKET 20 TEETH ENCODER SHAFT RPM 140 RPM ENCODER TURN RATIO 1.00 REV/LUG. VERIFEYE FENCE VERIFICATION SYSTEM - NO CALIBRATION PARTS5 VERIFEYE CAL BAR1 S/N: 10553-0111

800 TON YORK CENTRIFUGAL CHILLERS MODEL #YKL7LGH9-UEHS, NEW, NEVER USED UNDER LOAD. 800-TON CENTRIFUGAL COMPRESSOR WITH FACTORY INSTALLED VFD R-134A REFRIGERANT ALL CHILLED WATER AND CONDENSER WATER CONNECTIONS ARE VICTAULIC CONNECTIONS VARIABLE PRIMARY FLOW CONTROLS HOT GAS BYPASS FACTORY INSTALLED FLOW SWITCHES BACNET CONTROL INTERFACE UL LISTED, 460VAC/60HZ EVAP. COND. REFRIG. DWP, PSIG: 235 235 LIQUID DWP, PSIG: 150 150 NO. OF PASSES: 2 2 TUBE DESCRIPTION: 656 471 CONDENSER GAS INLET: BAFFLE REFRIGERANT: R-134A CHARGE, LBS: 2254 VOLTS-PHASE-HZ FLA OIL PUMP 2 HP 460-3-60 3.6 OIL HEATER N/A 460-3-60 3.0 S/N: SEGM-361770

2023 USNR SLOW DOWN BELT, 6' X 20', NEW, NEVER USED. INCLUDES BASE, FRAME ASSEMBLY, LEVELING BOLT, PIVOT FRAME, UPPER FRAME ASSEMBLY, BELT LIFT CYLINDER ASSEMBLY (18.5-22.5 INCH), CYLINDER PIN, SIDE SKIRT (20 FT), HYDRAULIC PUMP, BEARING END COVER, DRIVE GUARD ASSEMBLY, TAPER LOCK BUSHING (1.625 BORE AND 2.4375 DIAMETER BORE), SPROCKET (GT2, 14MM PITCH, 30T, 37MM BELT), POLYCHAIN GT2 BELT, 72 INCH WIDE 520 INCH ENDLESS A220 3 PLY 7/16 INCH GREEN DIAMOND BAREBACK BELT, HEX HEAD CAP SCREWS, LOCK WASHERS, HEX HEAD FLANGE BOLTS, HARD WASHERS, HEX NUTS, SQUARE HEAD SS W/ CUP PT SCREWS, HYDRAULIC HOSE EXTENSION, HEIGHT LIMITER (18.5-22.5 INCH), DRIVE MOUNT ADJUSTER (NORD SK324), 10 HP GEARMOTOR (NORD SK32, 5.70:1 RATIO, 1.625 SHAFT, M5 FOOT MOUNT, 3/60/460, TEFC, TB1, CEI).

2023 USNR SLOW DOWN BELT #1, 6' X 20', NEW, NEVER USED, DRIVE CALCULATIONS: MACHINE DESCRIPTION: SLOW DOWN BELT MOTOR RPM @ 59 HZ 1732 RPM OPERATING FREQUENCY 59 HZ REDUCER INPUT RPM 1732 RPM REDUCER RATIO 10.2 :1 REDUCER OUTPUT RPM 169.8 RPM REDUCER SPROCKET 45 TEETH HEAD PULLEY SPROCKET 50 TEETH HEAD PULLEY RPM 152.8 RPM HEAD PULLEY 12.5 IN. DIA. BELT SPEED 500.0 FPM S/N: 10552-0011

2023 USNR GRADING TRANSFER ASSEMBLY WITH ROLLCASE, NEW, NEVER USED. INCLUDES ELECTRICAL DEVICES, TAIL FRAME W/ROLLCASE ASSEMBLY, CHAINWAY ASSEMBLY, CHAINRUN C3X4.1 X 200IN LONG, LUG CHAIN ASSEMBLY (26 LUGS, 24 INCH SPACING, 624 INCH LG), SUPPORT FRAME W/ MOISTURE METER MOUNT, CHAINRUN C3X4.1 X 249IN LONG, DRIVE CHAINRUN C3X4.1 X 218IN LONG, GRADING TRANSFER SAFETY DECAL LAYOUT, 80 ROLLER CHAIN, 80 CONNECTING LINK & COTTER PINS. DRIVE CALCULATIONS: LUG TRANSFER OPERATING FREQUENCY 81 HZ, REDUCER INPUT RPM 2375, RATIO 17.81, OUTPUT RPM 133.3, HEADSHAFT RPM 93.3, LUG SPACING 24 PITCHES, LUG RATE 140.0 LPM. ROLL CALCULATIONS: DRIVEN FROM RPM 93.33, ROLL OUTSIDE DIAMETER 8.625 INCHES, ROLL SPEED 240.86 FPM. S/N: SPECIFICATIONS: QTY. DESCRIPTION UOM DWG - P/N --------------------------------------------------------------------------------- 1 ELECTRICAL DEVICES-EL 1 TAIL FRAME W/ROLLCASE ASSEMBLY1 6 CHAINWAY ASSEMBLY6 6 CHAINRUN C3X4.1 X 200IN LONG7 6 LUG CHAIN ASSEMBLY, 26 LUGS, 24" SPACING, 624" LG1 (52 FT) 1 SUPPORT FRAME W/ MOISTURE METER MOUNT5 1 CHAINRUN C3X4.1 X 249IN LONG6 1 DRIVE CHAINRUN C3X4.1 X 218IN LONG4 1 GRADING TRANSFER SAFETY DECAL LAYOUT0 1 80 ROLLER CHAIN, IMPORT FT G2-00024 1 80 CONNECTING LINK & COTTER PINS, ROLLER CHAIN EA G2-00022 DRIVE CALCULATIONS: MACHINE DESCRIPTION: LUG TRANSFER OPERATING FREQUENCY 81 HZ REDUCER INPUT RPM 2375 RPM REDUCER RATIO 17.81 REDUCER OUPUT RPM 133.3 RPM REDUCER OUPUT SPROCKET 21 TEETH HEADSHAFT DRIVEN SPROCKET 30 TEETH HEADSHAFT RPM 93.3 RPM HEADSHAFT SPROCKET 36 TEETH LUG SPACING 24 PITCHES LUG RATE 140.0 LPM DRIVE CALCULATIONS: MACHINE DESCRIPTION: LUG TRANSFER ROLLS DRIVEN FROM LUGGED TRANSFER DRIVEN FROM RPM 93.33 RPM DRIVEN FROM SPROCKET 24 TEETH GEARBOX DRIVEN SPROCKET 21 TEETH GEARBOX INPUT RPM 106.67 RPM GEARBOX OUTPUT SPROCKET 18 TEETH ROLLSHAFT DRIVEB SPROCKET 18 TEETH ROLLSHAFT RPM 106.67 RPM ROLL OUTSIDE DIAMETER 8.625 INCHES ROLL SPEED 240.86 FPM

MARLEY 800-TON COOLING TOWER CELL WITH DRIVES, EQUALIZATION PIPING, SS BASINS, ACCESS WALKWAYS. NEVER USED UNDER LOAD. UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. SPECIFICATIONS: MANUFACTURER: MARLEY MODEL NUMBER: NC NUMBER OF SEPARATELY OPERABLE CELLS PER TOWER: 3 COMMON SUMP FOR MULTI-CELL TOWER(S)? (YES/NO): 2 SEPARATE CELLS WITH EQUALIZER PIPING MATERIALS OF CONSTRUCTION (TOWER BASIN, STRAINER): STAINLESS STEEL HOT WATER AND COLD WATER BASINS MATERIALS OF CONSTRUCTION (TOWER CASING): GALVANIZED STEEL MATERIALS OF CONSTRUCTION (FAN BLADES): ALUMINUM DRIVE TYPE: GEAR BASIN SWEEP ACCESSORY (YES/NO): YES, FACTORY INSTALLED WATER TREATMENT ACCESSORY (DESCRIBE): BASIN SWEEP SAFETY GUARDRAILS: YES, PERIMETER GUARDRAIL SYSTEM ON ENTIRE FAN DECK ACCESS LADDER ACCESSORY (INSIDE/OUTSIDE/NONE): YES, ACCESS LADDER TO TOP OF EACH FAN DECK INTERNAL ACCESS LADDER ACCESSORY: YES, ACCESS LADDER WITH SERVICE PLATFORM INSIDE EACH CELL PLENUM WALKWAY: YES, ELEVATED STAINLESS WALKWAY ABOVE BASIN INSIDE EACH CELL DAVIT CRANE: YES, ONE PER CELL EXTENDED LUBE LINES (IF NECESSARY TO MAINTAIN MOTOR): YES AQUASTAT FOR SUMP HEATER PROVIDED BY: MANUFACTURER TYPE OF WATER LEVEL CONTROL (FLOAT, ELECTRONIC, NONE): ELECTRONIC WATER LEVEL CONTROLS LOW WATER INTERLOCK FOR SUMP HEATER PROVIDED BY: MANUFACTURER PHYSICAL DIMENSIONS LENGTH X WIDTH X HEIGHT (IN): 169" X 229" X 144" (EACH CELL) SERVICE & AIRFLOW CLEARANCE (FRONT/REAR/LEFT/RIGHT/TOP) (IN): 144" / 144" / 36" / 36" / 36" ORIENTATION (CONVENTION) (LEFT HAND, RIGHT HAND, STANDARD): RIGHT HAND, STANDARD OPERATING WEIGHT, INCLUDE FLUID & BASE WEIGHT (LBS): 32,000 (1 PER CELL) LEAVING WATER CONN. SIZE, QUAN, TYPE (IN, PSI/GROOVED/FLANGED): 1 @ 16" FL PER CELL ENTERING WATER CONN. SIZE, QUAN, TYPE (IN, PSI/GROOVED/FLANGED): 1 @ 16" FL PER CELL EQUALIZER PIPE CONNECTION SIZE (IN): 12" PER CELL EQUALIZER PIPE LOCATION (LEFT/RIGHT SIDE, BOTTOM): BOTTOM ALL CELLS MAKEUP WATER CONN. SIZE, TYPE (IN, PSI/GROOVED/FLANGED): 4" FL PER CELL DRAIN CONNECTION SIZE, QUAN, TYPE (IN, PSI/GROOVED/FLANGED): 4" FL PER CELL OVERFLOW CONNECTION SIZE, TYPE (IN, PSI/GROOVED/FLANGED): 4" FL PER CELL PERFORMANCE DESIGN FLOWRATE (GPM): 2,400 PER CELL AVAILABLE WATER FLOW (Y/N): YES MINIMUM OPERATING FLOWRATE (GPM): 1,680 PER CELL AMBIENT DESIGN SUMMER WETBULB (F): 78 TOWER ENTERING WATER TEMPERATURE (F): 91 TOWER LEAVING WATER TEMPERATURE (F): 81 TOWER ENTERING WATER REQUIRED PRESSURE (FT. HD.): 17 (GRAVITY FED) TOTAL FAN AIRFLOW PER TOWER (CFM): 512,900 DESIGN FAN SPEED (RPM): 514 MAXIMUM FAN BRAKE POWER (HP): 3 @ 65 BHP EVAPORATION RATE (GPM): 81.6 FAN MOTOR EFFICIENCY RATING (%NPH): 95.4 FAN MOTOR TO BE INVERTER DUTY?: YES FAN MOTOR MINIMUM EFFICIENCY (% BY NEMA STD MG1-1. 12): PREMIUM ELECTRICAL QUANTITY OF ELECTRICAL CONNECTIONS: 1 PER CELL VOLTAGE/PHASE FOR EACH CONNECTION: 460V / 3 PH QUANTITY OF FANS PER TOWER: 1 PER CELL FAN MOTOR HORSEPOWER: 30 BHP FAN BRAKE HORSEPOWER: 29.4 KW ELECTRIC SUMP HEATER ACCESSORY (W): YES ALTERNATE HEAT ON RANGE TEMPERATURE (F): BY EFFECTIVE HEAT ALTERNATE POWER SOURCE PROVIDED BY: MANUFACTURER VARIABLE FREQUENCY DRIVE PROVIDED BY: VFD WITH BYPASS START SEQUENCE BY: MANUFACTURER DISCONNECT SWITCH (MANUAL/AUTO) (Y/N): MANUFACTURER MAIN CIRCUIT AMPACITY (MCA, AMPS): 42 / 108 MINIMUM CIRCUIT AMPACITY (MCA, AMPS): 2 @ 108 S/N: 10169877-A2

MARLEY 800-TON COOLING TOWER CELL WITH DRIVES, EQUALIZATION PIPING, SS BASINS, ACCESS WALKWAYS. UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. SPECIFICATIONS: MANUFACTURER: MARLEY MODEL NUMBER: NC NUMBER OF SEPARATELY OPERABLE CELLS PER TOWER: 3 COMMON SUMP FOR MULTI-CELL TOWER(S)? (YES/NO): 2 SEPARATE CELLS WITH EQUALIZER PIPING MATERIALS OF CONSTRUCTION (TOWER BASIN, STRAINER): STAINLESS STEEL HOT WATER AND COLD WATER BASINS MATERIALS OF CONSTRUCTION (TOWER CASING): GALVANIZED STEEL MATERIALS OF CONSTRUCTION (FAN BLADES): ALUMINUM DRIVE TYPE: GEAR BASIN SWEEP ACCESSORY (YES/NO): YES, FACTORY INSTALLED WATER TREATMENT ACCESSORY (DESCRIBE): BASIN SWEEP SAFETY GUARDRAILS: YES, PERIMETER GUARDRAIL SYSTEM ON ENTIRE FAN DECK ACCESS LADDER ACCESSORY (INSIDE/OUTSIDE/NONE): YES, ACCESS LADDER TO TOP OF EACH FAN DECK INTERNAL ACCESS LADDER ACCESSORY: YES, ACCESS LADDER WITH SERVICE PLATFORM INSIDE EACH CELL PLENUM WALKWAY: YES, ELEVATED STAINLESS WALKWAY ABOVE BASIN INSIDE EACH CELL DAVIT CRANE: YES, ONE PER CELL EXTENDED LUBE LINES (IF NECESSARY TO MAINTAIN MOTOR): YES AQUASTAT FOR SUMP HEATER PROVIDED BY: MANUFACTURER TYPE OF WATER LEVEL CONTROL (FLOAT, ELECTRONIC, NONE): ELECTRONIC WATER LEVEL CONTROLS LOW WATER INTERLOCK FOR SUMP HEATER PROVIDED BY: MANUFACTURER PHYSICAL DIMENSIONS LENGTH X WIDTH X HEIGHT (IN): 169" X 229" X 144" (EACH CELL) SERVICE & AIRFLOW CLEARANCE (FRONT/REAR/LEFT/RIGHT/TOP) (IN): 144" / 144" / 36" / 36" / 36" ORIENTATION (CONVENTION) (LEFT HAND, RIGHT HAND, STANDARD): RIGHT HAND, STANDARD OPERATING WEIGHT, INCLUDE FLUID & BASE WEIGHT (LBS): 32,000 (1 PER CELL) LEAVING WATER CONN. SIZE, QUAN, TYPE (IN, PSI/GROOVED/FLANGED): 1 @ 16" FL PER CELL ENTERING WATER CONN. SIZE, QUAN, TYPE (IN, PSI/GROOVED/FLANGED): 1 @ 16" FL PER CELL EQUALIZER PIPE CONNECTION SIZE (IN): 12" PER CELL EQUALIZER PIPE LOCATION (LEFT/RIGHT SIDE, BOTTOM): BOTTOM ALL CELLS MAKEUP WATER CONN. SIZE, TYPE (IN, PSI/GROOVED/FLANGED): 4" FL PER CELL DRAIN CONNECTION SIZE, QUAN, TYPE (IN, PSI/GROOVED/FLANGED): 4" FL PER CELL OVERFLOW CONNECTION SIZE, TYPE (IN, PSI/GROOVED/FLANGED): 4" FL PER CELL PERFORMANCE DESIGN FLOWRATE (GPM): 2,400 PER CELL AVAILABLE WATER FLOW (Y/N): YES MINIMUM OPERATING FLOWRATE (GPM): 1,680 PER CELL AMBIENT DESIGN SUMMER WETBULB (F): 78 TOWER ENTERING WATER TEMPERATURE (F): 91 TOWER LEAVING WATER TEMPERATURE (F): 81 TOWER ENTERING WATER REQUIRED PRESSURE (FT. HD.): 17 (GRAVITY FED) TOTAL FAN AIRFLOW PER TOWER (CFM): 512,900 DESIGN FAN SPEED (RPM): 514 MAXIMUM FAN BRAKE POWER (HP): 3 @ 65 BHP EVAPORATION RATE (GPM): 81.6 FAN MOTOR EFFICIENCY RATING (%NPH): 95.4 FAN MOTOR TO BE INVERTER DUTY?: YES FAN MOTOR MINIMUM EFFICIENCY (% BY NEMA STD MG1-1. 12): PREMIUM ELECTRICAL QUANTITY OF ELECTRICAL CONNECTIONS: 1 PER CELL VOLTAGE/PHASE FOR EACH CONNECTION: 460V / 3 PH QUANTITY OF FANS PER TOWER: 1 PER CELL FAN MOTOR HORSEPOWER: 30 BHP FAN BRAKE HORSEPOWER: 29.4 KW ELECTRIC SUMP HEATER ACCESSORY (W): YES ALTERNATE HEAT ON RANGE TEMPERATURE (F): BY EFFECTIVE HEAT ALTERNATE POWER SOURCE PROVIDED BY: MANUFACTURER VARIABLE FREQUENCY DRIVE PROVIDED BY: VFD WITH BYPASS START SEQUENCE BY: MANUFACTURER DISCONNECT SWITCH (MANUAL/AUTO) (Y/N): MANUFACTURER MAIN CIRCUIT AMPACITY (MCA, AMPS): 42 / 108 MINIMUM CIRCUIT AMPACITY (MCA, AMPS): 2 @ 108 S/N: 10169877-A1

(3) 2023 USNR BACK LOG TABLES 1, 2, 3 - NEW, NEVER USED. INCLUDES CHAIN RUNS, SHARP TOP CHAIN, CONNECTING LINKS, OFFSET LINKS, ANGLE, AND DECAL LAYOUT. DRIVE CALCULATIONS PROVIDED FOR EACH TABLE WITH OPERATING FREQUENCY, SERVO REDUCER INPUT/OUTPUT RPM, REDUCER RATIO, SPROCKET TEETH COUNTS, HEAD SHAFT RPM, CHAIN SPEED, AND CHAIN RATE.

2023 USNR PLANER OUTFEED BELT, NEW, NEVER USED. DRIVE CALCULATIONS: MACHINE DESCRIPTION: PLANER OUTFEED BELT MOTOR RPM @ 60HZ 1756.5 RPM OPERATING FREQUENCY 80 HZ REDUCER INPUT RPM 2342 RPM MOTOR OUTPUT SPROCKET 38 TEETH HEAD SHAFT DRIVEN SPROCKET 180 TEETH HEADSHAFT RPM 494.4 RPM PULLEY DIAMETER 17 INCH BELT SPEED 2200.4 FPM S/N: 10552-0010

2023 USNR TRIMMER TRANSFER, NEW, NEVER USED, TRIMMER TRANSFER DRIVEN FROM ENDING ROLL TRANSFER HEADSHAFT DRIVEN FROM TRANSFER HEADSHAFT RPM 100.0 RPM DRIVEN FROM TRANSFER HEAD SHAFT SPROCKET 21 TEETH JACKSHAFT (TORQUE LIMITER) 30 TEETH JACKSHAFT RPM 70.0 RPM DRIVEN FROM JACKSHAFT 30 TEETH FENCE HEAD SHAFT DRIVEN SPROCKET 30 TEETH FENCE HEAD SHAFT RPM 70.0 RPM HEADSHAFT SPROCKET 18 TEETH LUG SPACING 9 PITCHES LUG RATE 140 LPM S/N: 10553-0113

BELL & GOSSETT VSC RHR MODEL 8X10X10.5B 10.5SSF PUMP WITH AMERICAN WHEATLEY SD12X10 SUCTION DIFFUSER, 2400 GPM, 96 FT.W.C., ABB DRIVES

2019 ABB DRIVE FOR CHW AND CW PUMP (CHW #1), NEW, NEVER USED UNDER LOAD. UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. SPECIFICATIONS: MFG DATE 2019 INPUT VOLTAGE (U1): 3PH 48...63 HZ VOLTAGE (U1): 380...480 VAC CURRENT (I1N): 124 A OUTPUT VOLTAGE (U2): 3PH 0...500 HZ VOLTAGE (U2): 0...U1 VAC CURRENT (I2N): 124 A SHORT CIRCUIT: 100 KA POWER (PN): 100 HP S/N: 2193002890

2019 ABB DRIVE FOR CHW AND CW PUMP (CWP #1), NEVER USED UNDER LOAD. INPUT VOLTAGE: 3PH 380-480 VAC, 124 A. OUTPUT VOLTAGE: 3PH 0-500 HZ, 124 A. SHORT CIRCUIT: 100 KA. POWER: 100 HP S/N: 2193002973

2019 ABB DRIVE FOR CHW AND CW PUMP (CHWP #2), NEW, NEVER USED UNDER LOAD. UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. SPECIFICATIONS: MFG DATE 2019 INPUT VOLTAGE (U1): 3PH 48...63 HZ VOLTAGE (U1): 380...480 VAC CURRENT (I1N): 124 A OUTPUT VOLTAGE (U2): 3PH 0...500 HZ VOLTAGE (U2): 0...U1 VAC CURRENT (I2N): 124 A SHORT CIRCUIT: 100 KA POWER (PN): 100 HP S/N: 2193002833

MAKE-UP WATER STATION INCLUDING: (2) RPBPS, CHECK VALVES, STRAINERS, ISOLATION AND BYPASS VALVES. SPECIFICATIONS: WILKINS 375A 2 1/2 65 13 DUCTILE IRON ASTM A 536 GRADE 4 DUCTILE IRON ASTM A 536 GRADE 4 FDA APPROVED ELECTROSTATIC EPOXY STAINLESS STEEL, 300 SERIES, NORYL STAINLESS STEEL, 300 SERIES EPDM (FDA APPROVED) BUNA NITRILE (FDA APPROVED) STAINLESS STEEL, BRAIDED HOSE

AMTROL 12,000GAL SYSTEM RATED EXPANSION TANK WITH GLYCOL RELIEF COLLECTION, NEVER USED UNDER LOAD. 125 PSIG WORKING PRESSURE, ASME APPROVED STEEL SHELL, REPLACEABLE BLADDER, SYSTEM CONNECTION NPTF MALLEABLE IRON, FINISH RED OXIDE PRIMER, AIR VALVE SCHRADER VALVE W/EPDM SEATS, FACTORY PRECHARGE 12 PSIG (.8 BAR), MAXIMUM OPERATING TEMPERATURE 240F (115C), MAXIMUM WORKING PRESSURE 125 PSIG (8.6 BAR)

BELL & GOSSETT VSC RHR MODEL 6X8X13.5B 13.375SSF SIC VERTICAL SPLIT CASE PUMP, NEW, NEVER USED, 1700 GPM 155 FT.W.C. ABB DRIVES

BELL & GOSSETT VSC RHR MODEL 6X8X13.5B 13.375SSF SIC VERTICAL SPLIT CASE PUMP, NEW, NEVER USED, 1700 GPM 155 FT.W.C. ABB DRIVES

BELL & GOSSETT VSC RHR MODEL 8X10X10.5B 10.5SSF PUMP WITH AMERICAN WHEATLEY SD12X10 SUCTION DIFFUSER, 2400 GPM, 96 FT.W.C., ABB DRIVES

2023 USNR LIVE SHEAR TABLE, NEW, NEVER USED. DRIVE CALCULATION: MACHINE DESCRIPTION: LIVE SHEAR TABLE OPERATING FREQUENCY: 75 HZ REDUCER INPUT RPM: 2188 RPM REDUCER RATIO: 35.25 REDUCER OUTPUT RPM: 62.1 RPM REDUCER OUTPUT SPROCKET: 21 TEETH HEAD SHAFT DRIVEN SPROCKET: 30 TEETH HEADSHAFT RPM: 43.4 RPM HEADSHAFT SPROCKET: 14 TEETH CHAIN SPEED: 132.2 FPM. DRIVE CALCULATIONS: MACHINE DESCRIPTION: LIVE SHEAR TABLE FENCE OPERATING FREQUENCY: 75 HZ REDUCER INPUT RPM: 2188 RPM REDUCER RATIO: 34.81 REDUCER OUTPUT RPM: 62.8 RPM HEADSHAFT SPROCKET: 25 TEETH CHAIN SPEED: 130.9 FPM S/N: 10551-0009

2023 USNR BACKLOG TABLES (#4) NEW, NEVER USED, OPERATING FREQUENCY: 60 HZ REDUCER INPUT RPM: 1750 RPM REDUCER RATIO: 35.25 REDUCER OUTPUT RPM: 49.6 RPM REDUCER OUTPUT SPROCKET: 24 TEETH HEAD SHAFT DRIVEN SPROCKET: 24 TEETH HEADSHAFT RPM: 49.6 RPM HEADSHAFT SPROCKET: 14 TEETH CHAIN SPEED: 151.1 FPM S/N: 10551-0010

2023 USNR REVERSING INCLINE TRANSFER, NEW, NEVER USED. MOTOR RPM @ 60HZ 1740 RPM OPERATING FREQUENCY 79 HZ REDUCER INPUT RPM 2291 RPM REDUCER RATIO 28.63 :1 REDUCER OUTPUT RPM 80.0 RPM REDUCER OUTPUT SPROCKET 56 TEETH HEADSHAFT DRIVE SPROCKET 56 TEETH LUGGED TRSF HEADSHAFT RPM 80.0 RPM DRIVEN FROM SPROCKET 21 TEETH INCLINE HEAD SHAFT DRIVEN SPROCKET 60 TEETH INCLINE HEADSHAFT RPM 28.0 RPM HEADSHAFT SPROCKET 40 TEETH LUG SPACING 8 PITCHES LUG SPEED 140 LPM LUG SPEED 243.5 FPM LUGGED TRANSFER ENCODER DRIVEN FROM LUGGED TRANSFER HEAD SHAFT DRIVEN FROM RPM 80.0 RPM DRIVEN FROM SPROCKET 42 TEETH ENCODER DRIVEN SPROCKET 24 TEETH ENCODER SHAFT RPM 140 RPM ENCODER TURN RATIO 1.00 REV / LUG S/N: 10553-0109

PIPING FLANGES, CONTROL, VALVES, ETC. CHILLED WATER AND CONDENSER WATER PIPING 16", 14", 12", 10", 8", AND 6" CHW PIPING, GROOVED CONTROL VALVES, ISOLATION VALVES, BALANCING VALVES, BUTTERFLY VALVES. FLOW METER 225B 8" 02000 GPM BACNET MS/TP 24VDC PIPE MOUNT FLOWRATE & TOTALIZER YES BACNET MS/TP 420MA (ANALOG) MODBUS RTU. FLOW METER 225B 6" 02000 GPM BACNET MS/TP 24VDC PIPE MOUNT FLOWRATE & TOTALIZER YES BACNET MS/TP 420MA (ANALOG) MODBUS RTU. FLOW METER 225B 3" 0200 GPM BACNET MS/TP 24VDC PIPE MOUNT FLOWRATE & TOTALIZER YES BACNET MS/TP 420MA (ANALOG) MODBUS RTU. V-1 3" COOLING TOWER BLOWDOWN BALL VALVE 150 THREADED FNPT LEVER HANDLE NIBCO T-585-70-LF. V-3 6" CHILLED WATER SUPPLY BUTTERFLY VALVE 150 FLANGED GEAR OPERATOR BRAY SERIES 30. V-5 8" HEATING WATER SUPPLY BUTTERFLY VALVE 150 FLANGED GEAR OPERATOR BRAY SERIES 30.

2023 USNR PACKAGE RE-ENTRY CHAINS (#1), NEW, NEVER USED. SPECIFICATIONS: OPERATING FREQUENCY: 60 HZ REDUCER INPUT RPM: 1750 RPM REDUCER RATIO: 37.05 REDUCER OUTPUT RPM: 47.2 RPM REDUCER OUTPUT SPROCKET: 21 TEETH HEAD SHAFT DRIVEN SPROCKET: 45 TEETH HEADSHAFT RPM: 22 RPM HEADSHAFT SPROCKET: 14 TEETH CHAIN SPEED: 67.1 FPM S/N: 10551-0006

2023 USNR UNSCRAMBLER BYPASS WITH CHAINS, NEW, NEVER USED. DRIVE CALCULATIONS: DROP OUT GATE DRIVEN FROM BY-PASS TABLE DRIVEN FROM RPM 62.1 RPM DRIVEN FROM SPROCKET 21 TEETH HEAD SHAFT DRIVE SPROCKET 28 TEETH HEAD SHAFT RPM 46.6 RPM HEAD SHAFT SPROCKET 35 TEETH RC80 CHAIN SPEED 136 FPM S/N: 10551-0005

2023 USNR FLYING BOARD TURNER, NEW, NEVER USED. SPECIFICATIONS: DRIVE CALCULATIONS: MACHINE DESCRIPTION: FLYING BOARD TURNER MOTOR RPM @ 60 HZ: 1750 RPM OPERATING FREQUENCY: 81 HZ REDUCER INPUT RPM: 2350.00 RPM REDUCER RATIO: 35.25 REDUCER OUTPUT RPM: 66.7 RPM REDUCER OUTPUT SPROCKET: 21 TEETH HEAD SHAFT DRIVEN SPROCKET: 30 TEETH HEADSHAFT RPM: 46.7 RPM HEADSHAFT SPROCKET: 12 TEETH LUG SPACING: 24 PITCHES LUG RATE: 140.0 LPM DRIVE CALCULATIONS: MACHINE DESCRIPTION: FLYING BOARD TURNER BELTS MOTOR RPM @ 60 HZ: 1750 RPM OPERATING FREQUENCY: 81 HZ REDUCER INPUT RPM: 2363 RPM REDUCER RATIO: 35.25 REDUCER OUTPUT RPM: 67 RPM REDUCER OUTPUT SPROCKET: 30 TEETH HEAD SHAFT DRIVEN SPROCKET: 21 TEETH HEADSHAFT RPM: 95.7 RPM PULLEY DIAMETER: 6 INCH BELT SPEED: 150.4 FPM S/N: 10552-0007

2019 CUSTOM ALLIANCE AIR PRODUCTS AHU, COOLING ONLY, SPARK PROOF, 57,000CFM (AHU 1). UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. SPECIFICATIONS: MODEL: MAWS-114-25-HB-FFF-CW-AS-PF MAX. AMPERE RATING OF SUPPLY FUSES: 110A MIN. SUPPLY CONDUCTOR AMPACITY: 90A SUPPLY FAN 30 HP, 460V, 3 PHASE, F.L.A 37.5, QUANTITY OF 2 CONTROL TRANS. 460V, 1 PHASE, F.L.A 2.87, QUANTITY OF 1 OVERALL ELEC. RATING, 3: 460 V, 77.17 A OVERALL ELEC. RATING, 1: 460 V INCLUDES SHOWN VALVE STATIONS ALUMINUM ENCLOSURES INTEGRAL DAMPERS S/N: 2691AHU01

2023 USNR UNSCRAMBLER BYPASS TIPPLE, NEW, NEVER USED. DRIVE CALCULATIONS: MACHINE DESCRIPTION: BYPASS TIPPLE CHAINS LIFT MOTOR RPM @ 60 HZ 1750 RPM OPERATING FREQUENCY 80 HZ REDUCER INPUT RPM 2333.3 RPM REDUCER RATIO 104 REDUCER OUTPUT RPM 22.4 RPM REDUCER OUTPUT SPROCKET 21 TEETH 120-2 DUPLEX DRIVESHAFT DRIVEN SPROCKET 60 TEETH 120-2 DUPLEX DRUM RPM 7.84 RPM WIND-UP DRUM DIAMETER 19.2 INCHES HOIST SPEED 15.8 IN/S MACHINE DESCRIPTION: BYPASS TIPPLE LIFT ENCODER DIRECT COUPLED TO UPPER TIPPLE LIFT DRIVESHAFT ENCODER SHAFT RPM 7.84 RPM HOIST RATE 120.918 IN/REV MACHINE DESCRIPTION: BYPASS TIPPLE CHAINS DRIVE FROM: PLANER OUTFEED LANDING TABLE HEAD SHAFT RPM 43.4 RPM HEAD SHAFT SPROCKET 51 TEETH RC60 LUG SPACING 28 PITCHES = 14 C2060H PITCHES = 21 INCHES LUG RATE 79.0 LPM CHAIN SPEED 138.25 FPM S/N: 10551-0003

2023 USNR PLANER OUTFEED LANDING TABLE WITH ANGLED ROLLS, NEW, NEVER USED. ROLLS OPERATING FREQUENCY: 75 HZ, REDUCER INPUT RPM: 2188 RPM, REDUCER RATIO: 21.87, REDUCER OUTPUT RPM: 100 RPM, ROLL DRIVE SPROCKET: 25 TEETH, ROLL SHAFT DRIVEN SPROCKET: 18 TEETH, ROLL SHAFT RPM: 138.9 RPM, ROLL SPIRAL PITCH: 12 IN, SPIRAL SPEED PARALLEL TO FLOW: 134.2 FPM. FENCE OPERATING FREQUENCY: 75 HZ, REDUCER INPUT RPM: 2188 RPM, REDUCER RATIO: 34.81, REDUCER OUTPUT RPM: 62.8 RPM, HEAD PULLEY DIAMETER: 8 IN, BELT SPEED: 131.6 FPM. OPERATING FREQUENCY: 75 HZ, REDUCER INPUT RPM: 2188 RPM, REDUCER RATIO: 35.25, REDUCER OUTPUT RPM: 62.1 RPM, HEAD SHAFT DRIVE SPROCKET: 21 TEETH, HEADSHAFT RPM: 43.4 RPM, HEADSHAFT SPROCKET: 14 TEETH, CHAIN SPEED: 132.2 FPM S/N: 10551-0002

2023 USNR PLANER BACKLOG TABLE #3, NEW, NEVER USED. SPECIFICATIONS: DRIVE CALCULATION: MACHINE DESCRIPTION PLANER BACKLOG TABLE #3 OPERATING FREQUENCY 60 HZ REDUCER INPUT RPM 1750 RPM REDUCER RATIO 35.25 REDUCER OUTPUT RPM 49.6 RPM REDUCER OUTPUT SPROCKET 24 TEETH HEAD SHAFT DRIVEN SPROCKET 24 TEETH HEAD SHAFT RPM 49.6 RPM HEAD SHAFT SPROCKET 14 TEETH CHAIN SPEED 151.11 FPM S/N: 10552-0009

TACO 5100GPM AIR SEPARATOR, NEVER USED UNDER LOAD. DESIGNED AND CONSTRUCTED PER ASME CODE SECTION VIII DIV. 1. REGISTERED WITH THE NATIONAL BOARD OF PRESSURE VESSEL MANUFACTURERS. STANDARD DESIGN PRESSURE AND TEMPERATURE: 125 PSI @ 240F. OPTIONAL DESIGN PRESSURE AND TEMPERATURE: 150 PSI @ 240F. PARTICLE REMOVAL DOWN TO 5 MICRONS. CONSTRUCTION: CARBON STEEL WITH EXTERIOR RED OXIDE PRIMER FINISH. 304 STAINLESS STEEL COALESCENCE PALL RINGS. TACO 4900 UNITS ARE DESIGNED TO BE SELF-SUPPORTING IN THE PIPING SYSTEM.

2023 USNR LUGGED TRANSFER WITH ROLLS ASSEMBLY, NEW, NEVER USED. LUGGED TRANSFER ROLLS DRIVEN FROM RPM 80.0 RPM DRIVEN FROM SPROCKET 21 TEETH GEARBOX DRIVE SPROCKET 18 TEETH GEARBOX INPUT RPM 93.33 RPM GEARBOX OUTPUT SPROCKET 21 TEETH ROLL SHAFT DRIVEN SPROCKET 18 TEETH ROLL SHAFT RPM 108.89 RPM ROLL DIAMETER 8.625 INCH ROLL SPEED 245.87 FPM LUGGED TRANSFER DRIVEN FROM REVERSING INCLINE TRANSFER OPERATING FREQUENCY 79 HZ REDUCER INPUT RPM 2290 RPM REDUCER RATIO 28.63 REDUCER OUTPUT RPM 80.0 RPM REDUCER OUTPUT SPROCKET 53 TEETH HEADSHAFT DRIVEN SPROCKET 53 TEETH HEAD SHAFT RPM 80.0 RPM HEADSHAFT SPROCKET 14 TEETH LUG SPACING 8 PITCHES LUG RATE 200.0 LPM REVOLVER LUG LOADER DRIVEN FROM LUGGED TRANSFER DRIVEN FROM RPM 80.0 RPM DRIVEN FROM SPROCKET 21 TEETH HEADSHAFT DRIVEN SPROCKET 72 TEETH HEADSHAFT RPM 23 RPM SHOE DISC SPEED 0.1667 REV/LUG LUG RATE 140.0 LPM S/N: 10553-0107

2023 USNR FLYING BOARD TURNER, NEW, NEVER USED. DRIVE TYPE: CHAINS, MOTOR HP: 5.0 HP, GEAR RATIO: 35.25:1, SPROCKET: 30 TEETH, CHAIN TYPE: RC80, DRIVEN RPM: 40.8 RPM. ENCODER DRIVEN FROM FLYING BOARD TURNER BELTS, DRIVEN FROM RPM: 40.8 RPM, DRIVEN FROM SPROCKET: 30 TEETH, ENCODER DRIVEN SPROCKET: 21 TEETH, ENCODER SHAFT RPM: 58.3 RPM, ENCODER TURN RATIO: 1.00 REV / LUG. BOARD TURNER CHAINS ENCODER DRIVEN FROM FLYING BOARD TURNER CHAINS, DRIVEN FROM RPM 40.8 RPM, DRIVEN FROM SPROCKET 72 TEETH, ENCODER DRIVEN SPROCKET 21 TEETH, ENCODER SHAFT RPM 140.0 RPM, ENCODER TURN RATIO 1.00 REV / LUG. BOARD TURNER BELTS ENCODER DIRECT CONNECTION TO BOARD TURNER BELTS MOTOR, ENCODER SHAFT RPM 2363 RPM, ENCODER RATE 0.764 IN / REV S/N: 10553-0108

2023 USNR LANDING TABLE, NEW, NEVER USED, CHAIN SPEED 151.1 FPM, HEADSHAFT RPM 54.3, REDUCER OUTPUT RPM 49.6, REDUCER RATIO 35.25, REDUCER INPUT RPM 1750, OPERATING FREQUENCY 60 HZ, WEIGHT OF TABLE: 7415 LBS S/N: 10553-0102

2023 USNR POSITIONING TRANSFER, NEW, NEVER USED, 70 RPM TRIMMER TRANSFER, 24 TEETH HEAD SHAFT SPROCKET, 21 TEETH HEAD SHAFT SPROCKET, 14 TEETH HEAD SHAFT SPROCKET, 8 PITCHES LUG SPACING, 140.0 LPM LUG RATE, 65 HZ OPERATING FREQUENCY, 1896 RPM REDUCER INPUT, 21.87 REDUCER RATIO, 86.7 RPM REDUCER OUTPUT, 15 TEETH REDUCER OUTPUT SPROCKET, 15 TEETH ROLL SHAFT DRIVEN SPROCKET, 86.7 RPM ROLL SHAFT, 8.625 INCH ROLL DIAMETER, 195.7 FPM ROLL SPEED S/N: 10553-0110

2023 USNR BACKLOG TABLES (#5), NEW, NEVER USED, OPERATING FREQUENCY: 60 HZ, REDUCER INPUT RPM: 1750 RPM, REDUCER RATIO: 35.25, REDUCER OUTPUT RPM: 49.6 RPM, REDUCER OUTPUT SPROCKET: 24 TEETH, HEAD SHAFT DRIVEN SPROCKET: 24 TEETH, HEADSHAFT RPM: 49.6 RPM, HEADSHAFT SPROCKET: 14 TEETH, CHAIN SPEED: 151.1 FPM S/N: 10551-0010

2023 USNR DUAL ARTICULATING SMART GATE, NEW, NEVER USED. SPECIFICATIONS: DRIVE CALCULATIONS: MACHINE DESCRIPTION: LUGGED TRANSFER ENCODER DRIVEN FROM LUGGED TRANSFER DRIVEN FROM RPM 93.3 RPM DRIVEN FROM SPROCKET 36 TEETH ENCODER DRIVEN SPROCKET 24 TEETH ENCODER SHAFT RPM 140.0 RPM ENCODER RATE 1.0 REV/LUG DRIVE CALCULATIONS: MACHINE DESCRIPTION: DUAL ACTING SMART GATE DRIVEN FROM LUGGED TRANSFER DRIVEN FROM RPM 93.3 RPM DRIVEN FROM SPROCKET 22 TEETH HEAD SHAFT DRIVEN SPROCKET 21 TEETH HEAD SHAFT RPM 97.8 RPM HEAD SHAFT SPROCKET 38 TEETH CHAIN SPEED 309.6 FPM S/N: 10552-0008

2023 USNR OVERHEAD PUSHER DROP OUT, NEW, NEVER USED. SPECIFICATIONS: 1 AIR SCHEMATIC-AS, 1 ELECTRICAL LAYOUT-EL, 1 SAFETY DECAL LAYOUT-SD, 1 LOWER DIVERTER FRAME ASSEMBLY, 1 FOUR POST HOIST, 1 UPPER FRAME ASSEMBLY, 1 AUTOGARD WRENCH, 320 SERIES EA MP70-W-A. MOTOR RPM @ 60 HZ 1780 RPM, REDUCER RATIO 78 HZ / 2270 RPM, OUTPUT RPM 858.3 RPM, ENCODER RATE 1.0000 REV/LUG. FAN MOTOR RPM @ 60 HZ 1750 RPM, DRIVEN FROM OVERHEAD PUSHER DROP OUT, DRIVEN FROM RPM 858.3 RPM, ENCODER RATE 16.2174 REV/LUG. ENCODER SHAFT RPM 2270.4 RPM, ENCODER RATE 16.2174 REV/LUG. ENCODER DRIVEN FROM OVERHEAD PUSHER DROP OUT, DRIVEN FROM RPM 858.3 RPM, DRIVEN FROM SPROCKET 20 T, ENCODER SHAFT RPM 140.0 RPM, ENCODER RATE 1.0000 REV/LUG. S/N: 10553-0116

2023 USNR ENDING ROLL TRANSFER, NEW, NEVER USED. DRIVE CALCULATIONS: MACHINE DESCRIPTION: ENDING ROLL TRANSFER DRIVEN FROM TRAY SORTER JACKSHAFT DRIVEN FROM RPM 93.33 RPM DRIVEN FROM SPROCKET 30 TEETH HEAD SHAFT DRIVE SPROCKET 28 TEETH HEAD SHAFT RPM 100.0 RPM HEADSHAFT SPROCKET 14 TEETH LUG SPACING 10 PITCHES LUG SPEED 140 LPM LUG RATE 304.4 FPM. DRIVE CALCULATIONS: MACHINE DESCRIPTION: ENDING ROLLS MOTOR RPM @ 60 HZ 1750 RPM OPERATING FREQUENCY 67 HZ REDUCER INPUT RPM 1954 RPM REDUCER RATIO 21.87 :1 REDUCER OUTPUT RPM 89.3 RPM REDUCER SPROCKET 21 TEETH HEAD PULLEY SPROCKET 15 TEETH HEAD PULLEY RPM 125.0 RPM ROLLS DIAMETER 10.75 INCH. DIA. BELT SPEED 352 FPM S/N: 10553-0117

2023 USNR TRIMMER OUTFEED HOLD DOWNS, NEW, NEVER USED. HOLD DOWN MOUNTING FRAME ASSEMBLY, TRIMMER OUTFEED HOLD DOWN SHOE ASSEMBLY, ELECTRICAL COMPONENTS, SAFETY DECALS, JUNCTION BOX AND CABLES, WIND-UP HANDLE, WIND-UP SHAFT, OUTFEED HOLD DOWNS, PIVOT PIN THRU 1 INCH OD X 3.75 INCH LG, PIVOT PIN THREADED 1 INCH OD X 3.75 INCH LG, STRAPPING NYLON 1 PLY X 2 WIDE, POINTER BACKING PLATE, BLOCK 2 PIPE UHMW, BEARING CAP .25 X 1.75 X 4.5, .125 DIA X 1.5 LG COTTER PIN, .625 DIA. HARD WASHER, SAE, GRADE 8, .625-18NF HEX NUT-STD-GR 8, .625-18NF HEX JAM NUT, 0.50-13 NC X 5 LG., HEX HEAD CAP SCREW, GRADE 8, 0.5000 STD LOCKWASHER, .375-16 NC HHCS X 1 LG., HEX HEAD CAP SCREW, GRADE 8, 0.3750 STD LOCKWASHER, .375 DIA HARD WASHER SAE GRADE 8 S/N: 10553- 0115

2023 USNR RE-ENTRY UNSCRAMBLER, NEW, NEVER USED. RAD BACK UNSCRAMBLER OPERATING FREQUENCY 75 HZ REDUCER INPUT RPM 2188 RPM REDUCER RATIO 28.32 REDUCER OUTPUT RPM 77.2 RPM REDUCER OUTPUT SPROCKET 21 TEETH HEAD SHAFT DRIVE SPROCKET 45 TEETH HEAD SHAFT RPM 36.0 RPM HEAD SHAFT SPROCKET 24 TEETH BAR SPACING 7 PITCHES BAR SPEED 123.6 LPM UNSCRAMBLER SPEED-UP OPERATING FREQUENCY 75 HZ REDUCER INPUT RPM 2188 RPM REDUCER RATIO 20.23 REDUCER OUTPUT RPM 108.1 RPM HEAD SPROCKET 36 TEETH CHAIN SPEED 324.4 FPM S/N: 10551-0008

(3) 2023 USNR BACKLOG TABLE, NEW, NEVER USED. CHAIN SPEED 151.1 FPM, HEADSHAFT RPM 54.3, REDUCER OUTPUT RPM 49.6, REDUCER RATIO 35.25, REDUCER INPUT RPM 1750, OPERATING FREQUENCY 60 HZ, REDUCER OUTPUT SPROCKET 24 TEETH, HEAD SHAFT DRIVEN SPROCKET 24 TEETH, HEAD SHAFT SPROCKET 14 TEETH