MidMonth MultiFacility CNC Fab No Reserve Auction

2010 PARKER MAXIGAS 112 ECBLM GENERATOR. 2 MAXIGAS-112 UNITS IN PARALLEL. 2 BUFFER MIXING TANKS. 165 SCFM COMPRESSED AIR INLET FLOW AT 150 PSIG. 39.3 SCFM 99.9% NITROGEN DISCHARGE AT 130 PSIG. DIGITAL DISPLAY OF O2. ECONOMY STANDBY CONTROL. FLOW VERIFICATION INDICATOR. 115 VOLT, SINGLE PHASE POWER REQUIREMENT. 12 CONNECTION FOR N2. 1 CONNECTION FOR INLET COMPRESSED AIR.

[1981] CINCINNATI CB135 PRESS BRAKE TONNAGE: 135 US OVERALL BED LENGTH: 12' DISTANCE BETWEEN HOUSING: 10' 6.25" STROKE: 8" OPEN HEIGHT: 15" CLOSE HEIGHT: 7" RAM ADJUSTMENT: 5" RAM SPEED HI / MED / LOW: 55 IPM / 20 IPM / 10 IPM RAM RETURN: 185 IPM MAIN MOTOR: 15HP EQUIPPED WITH AUTOMEC CNC 150 AUTOGAUGE, PROGRAMMABLE BACK GAUGE, DIE RAIL, RAM CLAMPS, ELECTRIC FOOT SWITCH, STROKE CONTROL, HYDRAULIC SYSTEM

1999 FANUC ARC MATE 100I ROBOT WELDER (1999) DESCRIPTION TABLE TOB FANUC ROBOT WELDER HAND HELD CONTROL + FANUC CONTROL + 450 POWER SUPPLY REACH: 53.9 IN 6 AXIS PAYLOAD: 13.2LB WEIGHT: 135KG 3-PHASE 50/60HZ

1982 CINCINNATI CINTURN U28 CNC LATHE CHUCK: 28'' SPINDLE BORE: 12'' SWING OVER BED: 33" TURNING DIAMETER: 36" MAXIMUM Z TRAVEL: 100" X TRAVEL: 18" DIMENSIONS: 264 X 121 X 146H WEIGHT: 55000LBS VOLTAGE: 480

[1999] DAEWOO LYNX 200B CNC LATHE - MAX TURNING DIAMETER: 11.0 MAX TURNING LENGTH: 11.8 MAX BAR CAPACITY: 1.75 SWING OVER BED: 18.0 DISTANCE BETWEEN CENTERS: 20.0 X AXIS TRAVEL: 6.3 Z AXIS TRAVEL: 13.0 RAPID TRAVERSE X AXIS: 787 IPM RAPID TRAVERSE Z AXIS: 945 IPM SPINDLE NOSE: A2-5 SPINDLE BORE: 2.0 SPINDLE SPEED: 35 5000 RPM SPINDLE MOTOR: 15HP TURRET CAPACITY: 12 STATIONS TURRET INDEX TIME: 0.15 SECOND OVERALL DIMENSIONS: 120" X 77" X 80" WEIGHT: 7600 LBS EQUIPPED WITH FANUC 21-T SERIES CNC CONTROL, RIGID TAPPING, 8 3 JAW HYDRAULIC CHUCK, TOOL PRESETTER, PARTS CATCHER, RS-232, COOLANT SYSTEM, FOOT SWITCH, TURBO CHIP CONVEYOR, EXTRA STEEL CHUCK JAWS

2006 MAZAK VCN 410A VMC X AXIS TRAVEL: 22 Y AXIS TRAVEL: 16.1 Z AXIS TRAVEL: 20 RAPID RATE X AXIS: 1,181 IPM RAPID RATE Y AXIS: 945 IPM RAPID RATE Z AXIS: 945 IPM POWER: 25HP 12,000 RPM ATC: 30 TAPER: CAT 40 TABLE (WXL): 16.1 X 35.4 DIMS: 78.74" X 102.36" X 110.24" WEIGHT: 10,580 LBS EQUIPPED WITH 1200 HOURS (RUN TIME) FUSION CONTROL CHIP CONVEYOR FIXTURE AND TOOL HOLDERS AVAILABLE 4TH AXIS

[2019] RDI COIL STRAIGHTENER CAPACITY: .078 THICK X 72" WIDE MANUFACTURED IN 2019 TECHNICAL SPECIFICATIONS: ROLL DIAMETER: STRAIGHTENER- 2.2 INCHES (56 MM) WITH POLYURETHANE COVERING (80-85 DUROMETER) FEED IN/OUT - 3.78 INCHES (96 MM) WITH HARD CHROME SURFACE ROLL QUANTITY: FEED ROLLS - 4 (1 ROLL SET ENTRY AND 1 EXIT) STRAIGHTENERS: 11 (5 OVER 6 CONFIGURATION WITH BACKUP ROLLS) ROLL ADJUSTMENTS: TOP ROLLS ADJUSTABLE VIA MOTORIZED ADJUSTMENT WITH HINGED ROLL OPENING MECHANISM FOR EASY CLEANING ROLL DRIVE: ROLLS DRIVEN BY AN AC MOTOR AND GEAR REDUCER TRANSMITTING POWER TO EACH ROLL VIA CHAIN AND SPROCKET ROLL TYPE: 52100 STEEL HARDENED ROLL BACKUPS: TOP AND BOTTOM SIDE GUIDES: AUTOMATIC, CENTERLINE JUSTIFIED LUBRICATION: AUTOMATIC LUBRICATION PNEUMATIC: PNEUMATIC VALVES MOUNTED TO MACHINE BASE AND FACTORY WIRED TO A MACHINE MOUNTED JUNCTION BOX HYDRAULIC: HYDRAULIC VALVES MOUNTED TO MACHINE BASE AND FACTORY WIRED TO A MACHINE MOUNTED JUNCTION BOX EQUIPPED WITH OUTFEED PINCH ROLL SHAFT NEEDS TO BE REPLACED, BUT EVERYTHING ELSE IS IN GREAT CONDITION WAS ONLY IN SERVICE FOR 1.5 YEARS

OKUMA GP-25T CYLINDRICAL GRINDER CONTROL TYPE OSP700 SWING - 12.99" CENTER DISTANCE - 25.6" MAX WEIGHT BETWEEN CENTERS- 110 OUNCES GRINDING WHEEL DIMENSIONS - 24 IN X 2.95 IN GRINDING WHEEL SPEED RPM - 8,859 RPM GRINDING WHEEL SPINDLE MOTOR - 10 HP WORK HEAD TAPER - #4 MT X-AXIS TRAVEL - 12.59" Z-AXIS TRAVEL - 25.59" INTERNAL GRINDING ATTACHMENT - NO PLUNGE MACHINE DIMENSIONS - 113 IN X 97.64 IN MACHINE WEIGHT - 12,000 POUNDS EQUIPPED WITH RENISHAW TOUCH PROBE MIST COLLECTOR

1997 NISSHINBO MAP-1000 II TURRET PUNCH. DESCRIPTION MAX. MATERIAL THICKNESS: .250" HOLE CAPACITY: 3.500" DIA. IN 14 GA. 1.125" DIA. IN .250" PUNCHING FORCE: 22 METRIC TONS MECHANICAL HYDRAULIC WET CLUTCH BRAKE: 24 IMPERIAL TONS ACCURACY X/Y LOCATION: +-.004" AUTO-INDEX: +-.05 DEGREES AXIS CONTROL SIMULTANEOUS 4 AXIS: X, Y, T, C AC SERVO MAX WORKPIECE SIZE STANDARD: 49.6" X 39.375" WITH REPOSITIONING: 99.2" X 39.375" WITH REPOSITIONING & SHEET ROTATION: 99.2" X 78.75" TURRET DRIVE: BI-DIRECTIONAL FEED CLEARANCE THICK: .787" THIN: .866" PRODUCTION RATES 1" CENTERS: 220 HPM NIBBLE: 350 HPM MAXIMUM AXIS SPEED: 2000 IPM AUTO-INDEX SPEED: 30 RPM, BI-DIRECTIONAL ELECTRICAL: 230/460/60, 12 KVA AIR REQUIREMENTS: 3.5 SCFM/ .5 CFM AT 90 PSI CONTROL TYPE: NISSHINBO PAL-500T INTERFACE: RS-232C STANDARD MULTI-TASKING: STANDARD GRAPHIC PROGRAMMING: STANDARD 14" COLOR MONITOR PROGRAM STORAGE: FLOPPY DISK, 100 PROGRAMS MEMORY: 12 PROGRAMS WITH 2000 BLOCKS EACH DIMENSIONS L X W X H: 158.3" X 90.6" X 86.6" WEIGHT: 24,000 LBS EQUIPPED WITH COMES WITH APPROXIMATELY 400 GPT CUSTOM TOOLS, MOSTLY 4-WAY RADIUS TOOLS INCLUDES KYOSHIN DENKI KOGYO MODEL DT-3 TRANSFORMER

[2000] YASKAWA MOTOMAN ERCR-UP20-8800 WELDING CELL 7 AXIS APPROXIMATELY 7' REACH STATIONARY ROBOT NO WELDING EQUIPMENT ATTACHED OR SUPPLIED NO FIXTURES OR TOOLING CNC POWER HEAD TWO TAIL STOCKS APPROXIMATELY 10' X 7' MAX PART DIAMETER WELDING CELL CAGES INCLUDED

1993 EXCEL 510 COLT VERTICAL MACHINING CENTER - MACHINE CONTROL: FANUC OMC CNC TABLE SIZE: 27.5" X 16.5" MACHINE TRAVELS (X/Y/Z): 20.1" X 16.2" X 18.1" TABLE CAPACITY: 660 LBS. SPINDLE TAPER: BT 40 SPINDLE SPEEDS: 200 - 6,000 RPM RAPID TRAVERSE RATE (X/Y/Z): 710 / 710 / 500 IPM TOOL CHANGER CAPACITY: 18 STATION POWER REQUIREMENT: 208V, 3 PHASE

1993 MORI-SEIKI SV500/40 VERTICAL MACHINING CENTER CONTROL TYPE MSC-501 # AXIS - 3 TABLE SIZE - 43.3" X 23.6" TABLE CAPACITY - 2,200 POUNDS X-AXIS TRAVEL - 40.2" Y-AXIS TRAVEL - 20.1" Z-AXIS TRAVEL - 20.1" RAPID TRAVERSE RATE (X/Y/Z) - 1,260 IPM SPINDLE TAPER - CAT 40 SPINDLE SPEED - 10,000 RPM MAIN MOTOR - 25 HP TOOL CHANGER CAPACITY - 30 EQUIPPED WITH PALLET CHANGER 1 PALLET 40 T

1993 EXCEL 610 COLT VERTICAL MACHINING CENTER X-AXIS TRAVEL: 25 IN (635 MM) Y-AXIS TRAVEL: 20 IN (508 MM) Z-AXIS TRAVEL: 22 IN (558 MM) TABLE SURFACE: 2712 1712 IN TABLE LOAD CAPACITY: APPROX. 1,100 LB (500 KG) SPINDLE TAPER: CAT 40 SPEED RANGE: 10,000 RPM SPINDLE MOTOR: 15 HP TOOL CHANGER: 20 ATC FANUC OM

JET 1860 3PGH ENGINE LATHE SWING OVER BED -16" SWING OVER CROSS SLIDE - 8-5/8" SWING THRU GAP - 25-5/8" LENGTH OF GAP - 10-5/8" DISTANCE BETWEEN CENTERS - 60" HOLE THRU SPINDLE - 3-1/8" RANGE OF SPEEDS - 25-1800RPM FEED RATES - 12 3 PHASE (230/460V) 7.5 HP EQUIPPED WITH FOLLOW REST, TAILSTOCK, THREADING, TOOL POST HOLDER, 3 JAW CHUCK (10 INCH DIA.), WORK LIGHT,

[1997] AMADA PROMECAM HFBO 100 PRESS BRAKE TONNAGE: 100 LENGTH: 10' CONTROL: AMADA MAX STROKE: 7.8" (200 MM) 3 PHASE 230/460 V 60 HZ WEIGHT: 15,000 LBS (6750 KG)

2012 AKIRA SEIKI RMV500APC VMC X-AXIS - 19.69" Y-AXIS - 11.81" Z-AXIS - 11.02" # AXIS - 3 POWER - 20 HP RPM - 15,000 RPM TAPER - BT30 # ATC - 24 TABLE-W - 11.81" TABLE-L - 19.69" CONTROL - CNC (AKIRA MI645) DIMENSIONS - 59.06" X 109.33" WEIGHT - 9,260 LBS EQUIPPED WITH TWO TABLES PALLET CHANGER COOLANT TANK CAPACITY: 40 GALLONS

1984 AMADA OCTO-334 TURRET PUNCH TONNAGE: 33 TURRET STATIONS: 8 MAX SHEET THICKNESS: .25 INCH WORKPIECE X AXIS: 29.5 INCH WORKPIECE Y AXIS: 39.3 INCH TOOLING INCLUDED ALL TOOLING IN PHOTO, ELECTRIC FOOT SWITCH, FANUC 6M CONTROL

[1986] AMADA FAB-100D PRESS BRAKE 100 TON 122" MAX BENDING LENGTH 106.3" DISTANCE BETWEEN HOUSINGS 15.75" THROAT DEPTH 3.94" STROKE 14.57" OPEN HEIGHT 17.2 GALLON HYDRAULIC RESERVOIR APPROXIMATELY 40 PIECES OF TOOLING INCLUDED WAS UNDER POWER WITHIN THE LAST MONTH EQUIPPED WITH ALL TOOLING IN PHOTO INCLUDED, CONTROL - NC-9EX, TWO SECTIONAL DIE RAILS, RAM CLAMPS, ELECTRIC FOOT SWITCH FOR OPERATION, GAP TYPE MACHINE, HYDRAULIC SYSTEM

WHITING 40A CIRCLE SHEAR 5/16 INCH CAP MECHANICAL CIRCLE SHEAR MAXIMUM CAPACITY NEEDED: 10' X 5/16'' MILD STEEL THROAT DEPTH: 48'' SHEAR BLADES: 6'' DIAMETER CUTTING SPEED: 5-10FPM DIMENSIONS (LRXFBXHEIGHT): 11'3'' X 4'6'' X 9'2'' TOTAL WEIGHT: 30,000LBS JOGGLES: 3/8'' METAL THICKNESS FLANGES CIRCLES: 3/8'' THICKNESS X 2-1/4'' DEPTH ADJUSTABLE BLANK HOLDER PNEUMATIC BLANK HOLDER AC MOTOR

2019 Doosan DNM 4500 Vertical Machining Center. Control: Fanuc 0i-M. CAPACITY: X axis travel 31.49", Y axis travel 17.71", Z axis travel 20.1". Table loading area 39.37" x 17.72". Allowable table load 1,320 lbs. Table T-slot spacing x width (3) - 125mm x 18H8 (3) - (4.92" x .71"). SPINDLE: Spindle nose to table top 15.9" to 26". Big Plus Spindle system CAT 40 Big Plus. Spindle speed 8,000 rpm. AC Spindle Motor (S3 25%) 15 / 20 hp. Spindle Torque (S3 15%) 211 ft-lbs. Spindle Acceleration Deceleration time 0 - 8k (3.53 sec) 8k - 0 (2.52 sec). Equipped With 30 ATC, Thru Spindle Coolant - 230 PSI, Renishaw probe, Tool setter, LNS MH250 filtration conveyor. 4,842 Cutting Hours.

OKUMA GA 25T CYLINDRICAL GRINDER ANGLE HEAD SWING OVER TABLE: 12.99 MAX GRINDING DIA.: 7.87 MAX WORKPIECE LENGTH: 13.78 TRAVEL RANGE: 25.59 AUTO INFEED RATE: .000024 TO 236 IPM POSITIONING RATE: 630 IPM WORK SPINDLE SPEED: MAX. 800 RPM BORE TAPER: MT-4 AUTO TRAVEL MANUAL TAPER OFFSET:.0031 ANGLE HEAD EQUIPPED WITH OSP700G CNC MARPOSS GAUGING

[24.5] SWING OVER TABLE, [90 DEGREES] ANGULAR ADJUSTMENT OF WORKHEAD, [11 1/2] WORKHEAD CROSS SLIDE TRAVEL, [20] TABLE TRAVEL MAX. GRINDING STROKE, [16] MAXIMUM GRINDING STROKE, [1 1/2] WHEELHEAD CROSS SLIDE TRAVEL, [0 TO 18 FPM] TABLE SPEED RANGE, [18 FPM] RAPID TRAVERSE OF TABLE, [5 HP] WHEELHEAD MOTOR, [REVERSIBLE & VARIABLE: 0 - 500 RPM] WORKHEAD SPEEDS, [480V/3PH/60HZ] ELECTRICAL REQUIREMENTS, APPROX DIMENSIONS: [96(L-R) X 64(F-B) X 75(H)], EST. WEIGHT: [7,000 LBS], EQUIPPED WITH 3 JAW CHUCK, INTEGRATED COOLANT SYSTEM, INTEGRATED HYDRAULIC SYSTEM. HEALD 273 A ID GRINDER

1994 BRIDGEPORT SERIES I EZ-TRAK MANUAL MILLING MACHINE TABLE TRAVEL (X-AXIS): 30 SADDLE TRAVEL (Y-AXIS): 12 SPINDLE TRAVEL (Z-AXIS): 5 TABLE SIZE: 48 X 9 T-SLOTS: 3 ON 2.5 CENTERS T-SLOT SIZE: .00625 HEIGHT ABOVE FLOOR (MAX): 47.4 MAXIMUM VERTICAL LOAD UNIFORM DISTRIBUTION: 300 LBS POSITIONING: AUTO (X,Y): 100 IPM MANUAL (X,Y): 100 IPM FEEDRATE RANGE (X,Y): 0.1-100 IPM MINIMUM INCREMENT: 0.0001 IN. SPINDLE: A.C. SPINDLE MOTOR RATING: 2 HP POWER RATING (DUTY CYCLE): 3 HP POWER: INPUT POWER: 208/230/460 VOLTS 3 PHASE 50/60 CYCLES POWER CAPACITY: 4KVA SPACE AND WEIGHT: FLOOR SPACE: 98 X 64 (DOOR OPEN: 98 X 87) MACHINE HEIGHT: 82 WORKING SURFACE: 48 X 9 APPROX WEIGHT: 2,200 LBS MILLING HEAD SPECIFICATIONS: MODEL: 2J POWER: 2 HP MOTOR RPM: 1,800 RPM SPEED RANGES- RPM: LOW (60-500), HIGH (500-4200) QUILL TRAVEL: 5 QUILL DIAMETER: 3.375 SPINDLE TAPERS: R-8 #30 Q.C. SPINDLE DIAMETER: 1.875 DRILLING CAPACITY (MANUAL): 0.87 DRILLING CAPACITY (POWER): 0.37 BORING CAPACITY: 6 MILLING CAPACITY: 2 CU. IN./MIN. SPINDLE TO COLUMN: 6 23"

[1975] ROUSELLE #8 85T OBI PRESS TONNAGE: 85 STROKE: 8" SHUT HEIGHT: 16" ADJUSTMENT: 4" STROKES/MIN: 100 BED AREA: 48" L X 22" F-B RAM AREA: 41" L X 16" F-B DISTANCE BETWEEN UPRIGHTS: 60" MOTOR: 15HP 3-PHASE DRIVE SYSTEM: FLYWHEEL WITH AIR CLUTCH & BRAKE WEIGHT: 10,000-12,000LBS OVERALL DIMENSIONS: 65" L-R X 82" F-B X 113" H EQUIPPED WITH AIR CLUTCH AND BRAKE, UPDATED ROSS VALVE, DUAL PALMS FOR OPERATION, BOLSTER,

[2024] MILLTRONICS IV MANUAL MILLING MACHINE 3 AXIS(X,Y,Z) TABLE DIMENSIONS - W X L - 13" X 42" X AXIS TABLE LONGITUDINAL TRAVEL - 32" Y AXIS SADDLE CROSS TRAVEL - 16" TABLE LOAD CAPACITY - 800 LBS SPINDLE TO TABLE, MAXIMUM - 17" SPINDLE TAPER - #30 CAT SPINDLE SPEEDS - 0 TO 4250 RPM POWER RAPID TRAVERSE RATE (X/Y) - 300 IPM 13 X 42 TABLE NEW SPINDLE MOTOR - 2024 EQUIPPED WITH CENTROID ACORN CONTROL (NEW IN 2024), 5 TOOLS HOLDERS INCLUDED, WINDOWS 10 COMPUTER (24 INCH TOUCH SCREEN), CENTROID DXF IMPORT, VFD DRIVE ON SPINDLE (NEW IN 2024)

2000 MIGHTY VIPER VMC 1500 VERTICAL MACHINING CENTER 4TH AXIS X - 60" Y - 30" Z - 30" TAPER - 50 HORSE POWER - 8,000 RPM EQUIPPED WITH CONTROL - CNC (MITSUBISHI) TSUDAKOMA 4TH AXIS

1995 MAZAK FJV 20 VERTICAL MACHINING CENTER TABLE SIZE: 31.5 X 18.1 X-AXIS TRAVEL: 22 INCH Y-AXIS TRAVEL: 16 INCH Z-AXIS TRAVEL: 16 INCH AUTO TOOL CHANGER: 21 TAPER: CAT 40 SPINDLE SPEED: 12,000 RPM MOTOR: 25 HP APPROX WEIGHT: 9,000 LB APPROX DIMENSIONS (L X W X H): 83 X 84 X 107.5 EQUIPPED WITH CHIP CONVEYOR, MAZATROL M PLUS

1995 MAZAK FJV 20 VERTICAL MACHINING CENTER TABLE SIZE: 31.5 X 18.1 X-AXIS TRAVEL: 22 INCH Y-AXIS TRAVEL: 16 INCH Z-AXIS TRAVEL: 16 INCH AUTO TOOL CHANGER: 21 TAPER: CAT 40 SPINDLE SPEED: 12,000 RPM MOTOR: 25 HP APPROX WEIGHT: 9,000 LB APPROX DIMENSIONS (L X W X H): 83 X 84 X 107.5 EQUIPPED WITH CHIP CONVEYOR MAZATROL M PLUS

1998 HURCO HAWK 40/SSM VERTICAL MILLING MACHINE 13X58 WORK TABLE TAPER 40 80 TO 3800 RPM 16" Y TRAVEL 31" X TRAVEL 230 VOLTS MACHINE SIZE IS 65 X 60 X 88 MACHINE WEIGHTS 5500 POUNDS EQUIPPED WITH HURCO ULTIMAX SSM (MOUNTED SCREEN FOR DIGITAL READOUT), DRAW BAR, WORK LIGHTS,

AMERICAN STYLE PRESS BRAKE TOOLING (QTY: 15) PUNCHES: 1 INCH GOOSENECK PUNCH: RATED UP TO 10 GAUGE .43 INCH GOOSENECK PUNCH: RATED UP TO16 GAUGE .75 INCH SASH PUNCH: RATED UP TO10 GAUGE HEMMING PUNCH: RATED UP TO 18 GAUGE 2 INCH BLOCK PUNCH: RATED UP TO 1/2 INCH .625 ACUTE PUNCH: RATED UP TO 14 GAUGE DIES: .25 INCH SINGLE V : RATED UP TO 22 GAUGE .375 INCH SINGLE V : RATED UP TO 18 GAUGE .75 INCH SINGLE V : RATED UP TO 13 GAUGE .875 INCH SINGLE V : RATED UP TO 12 GAUGE 1.25 INCH SINGLE V : RATED UP TO 9 GAUGE 1.5 INCH SINGLE V : RATED UP TO 3/16 INCH 2 INCH SINGLE V : RATED UP TO 1/4 INCH HEMMING DIE : RATED UP TO 18 GAUGE .625 ACUTE DIE : RATED UP TO 14 GAUGE

[2001] FRASER 1856-Z3 MECHANICAL SHEAR 10FT X 1/4" HYDRAULIC SWING BEAM SHEAR FRONT OPERATED 24 INCH POWER BACK GAUGE 1 SQUARING ARM 3 SUPPORT ARMS MANUAL CLEARANCE ADJUSTMENT

[2001] FRASER HYDRAULIC SHEAR 10FT X 1/4 HYDRAULIC SHEAR 185 TON X 13FT HYDRAULIC PRESS BRAKE HYDRAULIC MOTOR BACK GAUGE - 24 INCH MANUAL CONTROL BETWEEN THE HOUSING LENGTH - 11FT 2 FRONT SUPPORT ARMS GAP TYPE MACHINE EQUIPPED WITH **TOOLING NOT INCLUDED**

2006 TRUMPF TRULASER 3030 LASER CUTTING MACHINE TABLE SIZE 60" X 120" TYPE CO2 WATTAGE 4000 WATTS IPM 3346 INCHES-PER-MINUTE X-TRAVEL 120 INCHES Y-TRAVEL 60 INCHES Z-TRAVEL 4.5 INCHES MAX WORKPIECE WEIGHT 1,980 LBS MAX CUT (MILD STEEL): .80 MAX CUT (STAINLESS STEEL): .63 MAX CUT (ALUMINUM): .39 TYPE OF CNC CONTROL SIEMENS 840D BEAM ON TIME: 11,929 HOURS EQUIPPED WITH CHILLER, DUST COLLECTOR, TRUFLOW 4000W RESONATOR, DUAL PALLET SHUTTLE TABLE.

1994 BRIDGEPORT SERIES II MANUAL MILLING MACHINE X AXIS TRAVEL: 30" Y AXIS TRAVEL: 12" Z AXIS (QUILL) TRAVEL: 5" KNEE TRAVEL: 14.5" TABLE SIZE: 9" X 48" HEAD TILT: +/- 90 DEGREES SPINDLE SPEEDS: 60-4,200 RPM SPINDLE TAPER: #30 WITH BRIDGEPORT POWER DRAW BAR SPINDLE MOTOR: 2 HP DUAL VOLTAGE 220/440 WIRED 480 V 3PH AT THIS TIME EQUIPPED WITH QUICK CHANGE COLLET, TOOLING