Industrial Electronic Manufacturing Process Equipment Parts Tools Day 3 of 3 day event

(4) TWO LOCKING TWO NON-LOCKING INDUSTRIAL SWIVEL TYPE CASTER WHEELS SWIVEL TYPE TWO LOCKING TWO NON-LOCKING WHEEL DIAMETER: 3" WHEEL WIDTH: 1" TOTAL HEIGHT: 3.75" BASE DIMENSIONS: 3.75" X 2.75" BOLT HOLE WIDTH: 1.75" X 3"

[FAULTLESS] 3.C STAINLESS STEEL SWIVEL 3" ROLLING CASTER WHEELS (4) - MANUFACTURER: FAULTLESS MODEL: 3.C CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THE CASTERS ARE IN USED CONDITION WITH SCUFFS, SCRATCHES, AND SOME RESIDUE FROM PREVIOUS USE. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: THE CASTERS WERE REMOVED FROM DECOMMISSIONED MACHINES. THE WHEELS ROLL AND THE SWIVEL BASE WORKS AS INTENDED. NO FURTHER TESTING WAS PERFORMED AFTER REMOVAL. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (4) FAULTLESS 3.C STAINLESS STEEL SWIVEL TYPE CASTER WHEELS SPECIFICATIONS: MANUFACTURER: FAULTLESS MODEL: 3.C DESCRIPTION: FAULTLESS 3.C STAINLESS STEEL CASTER WHEELS SWIVEL TYPE WHEEL DIAMETER: 3" WHEEL WIDTH: 1.75" BASE DIMENSIONS: 3.25" X 4.25" TOTAL HEIGHT: 4" BOLT HOLE WIDTH: 3.50" X 2.50" SKU: W21G016 4B-04-02(2) 9LBS - 10IN X 10IN X 6IN

2012 SCHMIDT ST3 SIGMAWIG WELDED STAINLESS HEAT EXCHANGER 10 PLATE 12" X 4" - MANUFACTURER: SCHMIDT MODEL: ST03 CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THIS HEAT EXCHANGER IS IN FAIR COSMETIC CONDITION. THE OUTSIDE IS WRAPPED WITH A 3MM LAYER OF GLUED-ON INSULATION. INSIDE THERE ARE SOME LIGHT RESIDUES FROM PRIOR USE INSIDE. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: THIS WAS TAKEN FROM A DECOMMISSIONED SINGLE TEMPERATURE CONTROLLER AND NOT TESTED SEPARATELY. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) SCHMIDT ST03 HEAT EXCHANGER SPECIFICATIONS: MANUFACTURER: TENEZ/API SCHMIDT SIGMAWIG PLATE HEAT EXCHANGER TYPE STO3 PB-01063 ALL-WELDED STAINLESS CONSTRUCTION ALL WETTED PARTS ARE STAINLESS 10 PLATES WELDED THREADED CONNECTIONS (NOT SURE THE THREAD SIZE, PIPES ARE 35.5MM OD) PRESSURE RATING: -1 TO +25 BAR TEMPERATURE RATING: -195 TO 250 OC VOLUME: 1.2 LITERS PER SIDE MAXIMUM FLOW RATE: 8.5 CUBIC METERS/HOUR PLATE DIMENSIONS: 30 X 10 CM OVERALL DIMENSIONS INCLUDING FITTINGS: 30 X 29 X 11 CM BOLT-DOWN MOUNTING CONSTRUCTED IN 2012

2011 VITRONICS SOLTEC XPM3I 1030 REFLOW OVEN POWER 3PHASE 480V 70A DUAL EDGE-SUPPORTING PIN CHAIN CONVEYORS 10 HEATING ZONES, 3 COOLING ZONES WEIGHT: 2.5 TONS MANUFACTURED IN NOVEMBER 2011

[NEW] RENISHAW RGH34 INCREMENTAL ENCODER SYSTEM 0.1UM 8MHZ MADE IN UK (1) NEW RENISHAW RGI34Y00A31 RGH34 INCREMENTAL ENCODER SYSTEM 0.1UM 8MHZ. MANUFACTURER: RENISHAW MODEL: RGH34 PART NUMBER: RGI34Y00A31 INCREMENTAL ENCODER SYSTEM 0.1 UM 8 MHZ REF READHEAD SIZE: 15 X 15 X 10.5 MM RESOLUTIONS UP TO 50 NM SPEED: UP TO 8 M/S ANALOG OR DIGITAL OUTPUTS POWER: 5 V TEMPERATURE: -20 TO 70 C ACCELERATION: 500 M/S2, 3 AXES SCALE LENGTH: UP TO 50 M

[NEW] HOUGEN 75617 HYDRAULIC PUNCH PRESS ROUND DIE (1/2" CC DIAMETER) S/N: V02U007 4B-04-02(1) 2LBS - 6IN X 6IN X 4IN

2003 CONVEYOR TECHNOLOGIES SG-69I-E-LT-0640 SLIDE GATE PCB BOARD 30" AISLE WIDTH. THIS CONVEYOR IS IN FAIR COSMETIC CONDITION. THE VIEWING WINDOWS ARE SCUFFED AND SCRATCHED. THERE ARE HEAVY SCUFFS/SCRATCHES AND ADHESIVE LABEL RESIDUES HERE-AND-THERE ALL OVER THE MACHINE. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS GATE IS IN GOOD WORKING CONDITION. WE SAW THE CONVEYOR EXTEND AND RETRACT, THE BELTS ON BOTH SIDES RUN, AND ALL THE SENSORS WORK. THE OPTICAL AISLE-BLOCKED SENSORS REQUIRE A REFLECTOR EACH (NO REFLECTORS ARE INCLUDED). THE BUMP SWITCHES WORK. THE STACK LIGHT LIT UP RED AND AMBER AND GAVE A WARNING TONE, BUT WE NEVER SAW GREEN. NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) CTI SG-69I SHUTTLE GATE CONVEYOR SPECIFICATIONS: MANUFACTURER: CONVEYOR TECHNOLOGIES MODEL: SG-69I-E-LT-0640 SHUTTLE GATE CONVEYOR OPEN-CENTER EDGE BELT CONVEYOR TYPICALLY USED FOR PCBS CONVEYOR LENGTH: 1M GATE PROJECTS OUT 30" (STOPS ARE ADJUSTABLE) ADJUSTABLE WIDTH, LOOKS LIKE 2.5" TO 16.5" ADJUSTMENT RANGE OMRON SYSMAC CPM2A PLC CONTROLLER POWER: 120V 60HZ 3A MANUFACTURED: 2003 SKU: X17D015 5I-08-03(1) 685LBS - 49IN X 46IN X 62IN

2010 SWEP B25HX16/1P-SN-S INDUSTRIAL HEAT EXCHANGER MAX-WORKING-PRESSURE:1.2MPA S/N: 110117142000032 MAX FLOW: 9 M CUBED/HOUR, 36.63 GPM CHANNEL VOLUME: 0.114/0.114 DM CUBED CONSTRUCTION: 316/316L STAINLESS STEEL PLATES, COPPER BRAZING LENGTH: 20.75" WIDTH: 4.5" HEIGHT: 2" MAX WORKING TEMPERATURE: 200 C MAX WORKING PRESSURE: 1.2 MPA TEST PRESSURE: 2.4 MPA VOLUME: 0.798L PRIMARY, 0.912L SECONDARY

KENNAMETAL 1866686 VBGT221F KC5010 DIAMOND CARBIDE TURNING INSERT (20) - MANUFACTURER: KENNAMETAL MODEL: 1866686 CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THESE CARBIDE INSERTS WERE VERY SLIGHTLY USED AND CAREFULLY INSPECTED FOR FLAWS. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: THESE CARBIDE INSERTS WERE VERY SLIGHTLY USED AND CAREFULLY INSPECTED FOR FLAWS. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (20) KENNAMETAL 1866686 VBGT221F KC5010 DIAMOND CARBIDE TURNING INSERT SPECIFICATIONS: MANUFACTURER: KENNAMETAL MODEL: 1866686 ISO NO: VBGT110304LF ANSI NO: VBGT221LF DESCRIPTION: VBGT221F KC5010 DIAMOND CARBIDE TURNING INSERT GRADE: KC5010 CHIP BREAKER: LF THICKNESS: 1/8" (3.175MM) LENGTH: 0.4358" (11.07MM) INSCRIBED CIRCLE: 0.2500" (6.35MM) CORNER RADIUS: 0.0156" (0.39624MM) COATING: TIAIN SKU: T04U018

2017 CONVEYOR TECHNOLOGIES FIFO-2-30/60-RL-2514 CONVEYOR PCB BUFFER FIFO/LIFO CTI THIS BUFFER IS IN FAIR COSMETIC CONDITION. THE OUTSIDES SOME LOTS OF SCUFFS/SCRATCHES AND ADHESIVE LABEL RESIDUES FROM PRIOR USE. THERE ARE SOME SCRATCHES ON THE TOUCHSCREEN THAT DON'T SEEM TO INTERFERE WITH OPERATION. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. THIS CONVEYOR IS IN GOOD WORKING CONDITION AS FAR AS WE CAN TEST. WE DON'T HAVE A PASSWORD TO CHANGE MODES, AND IT KEEPS GIVING COMMUNICATION ERRORS, WE SUSPECT FOR NOT BEING CONNECTED TO WHATEVER IT WAS FORMERLY TALKING TO IN THE PREVIOUS INSTALLATION. THE TOUCHSCREEN WORKS ALTHOUGH IT IS SOMEWHAT SLOW RESPONDING TO TOUCH INPUTS. THE SENSORS ALL LIT UP. NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) CTI FIFO-2-30/60-RL-2514 CONVEYOR BUFFER SPECIFICATIONS: MANUFACTURER: CONVEYOR TECHNOLOGIES MODEL: FIFO-2-30/60-RL-2514 CONVEYOR BUFFER EDGE-SUPPORTING CONVEYORS CONVEYOR LENGTH: 2 METERS OVERALL (4) CONVEYOR SECTIONS TOTAL VARIABLE CONVEYOR WIDTH NUMBER OF CONVEYOR STATIONS: 29 CAN OPERATE IN FIFO, LIFO OR PASSTHROUGH MODE FANS FOR OPTIONAL PCB COOLING INSIDE THE BUFFER POWER: 120V 60HZ 17.26A PLUS COMPRESSED AIR MANUFACTURED: 2017 SKU: W36D018 6-BILR1(1) 1850LBS - 88IN X 70IN X 91IN

[EASTEY EM16TTK] L-BAR SEALER WITH HEAT SHRINK TUNNEL COMMERCIAL SEALER SYSTEM - MANUFACTURER: EASTEY MODEL: EM16TTK. THIS SEALER SYSTEM IS IN GOOD COSMETIC CONDITION WITH SOME MINOR SCUFFS AND SCRATCHES FROM REGULAR COMMERCIAL USE. WE POWERED ON THIS SEALER SYSTEM AND SET THE OVEN TEMPERATURE AT 300 DEGREES F (HEAT TOGGLED B/W 299-300 DEGREES F - BUT CONSISTENT), ADJUSTED THE L-SEALER TIMER, ADJUSTED THE FILM PLATE, AND LOADED THE FILM ONTO THE FILM SPINDLE. WE THEN LOADED SOME DUMMY PRODUCT INTO THE FILM AND CLOSED THE L SEALER TO OBSERVE THE MAGNETIC LOCKS HOLDING THE BRACKET DOWN UNTIL THE FILM WAS HEAT CUT. WHEN THE L SEALER WAS LIFTED THE CONVEYOR TURNED ON TAKING THE PACKAGE INTO THE HEAT SEALER AND EXITING THE MACHINE SHRINK-WRAPPED. WE CONFIRMED THAT THE CONTROLLERS FOR THE CONVEYOR SPEED, THE OVEN TEMPERATURE, THE SEALER TIMER, AND THE SEALER HEAT WERE ALL FUNCTIONING AS DESIGNED. AFTER TESTING THE POWER PLUG WAS REMOVED LEAVING BARE WIRES. NO ADDITIONAL TESTING WAS PERFORMED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) EASTEY EM16TTK COMBINATION L SEALER SHRINK TUNNEL OVEN COMMERCIAL SEALER SYSTEM (1) FULL ROLL OF SEALED AIR D955 75 GAUGE 18" X 3500FT FILM (1) PARTIAL ROLL OF SEALED AIR D955 75 GAUGE 18" X 3500FT FILM SPECIFICATIONS: MANUFACTURER: EASTEY MODEL: EM16TTK DESCRIPTION: COMBINATION L SEALER SHRINK TUNNEL OVEN COMMERCIAL SEALER SYSTEM 220VAC 50A 1 PHASE 60HZ SEMI-MANUAL OPERATION HOT WIRE SEAL SYSTEM MAX PRODUCT HEIGHT: 7" TUNNEL CHAMBER WIDTH: 18" TUNNER CHAMBER HEIGHT: 10" SEAL DIMENSIONS: 20" X 16" FILM SEALED: POLYETHYLENE, POLYOLEFIN, PVC.

(LOT OF 4) CASTERS 4" X 1.25" HEAVY DUTY INDUSTRIAL ALL STEEL SWIVEL AND LOCKING - MANUFACTURER: VARIOUS MODEL: VARIOUS WHEEL: 4" X 1.25" MOUNTING PLATE: 4" X 3" GALVANIZED STEEL SKU: R02G025 2N-01-02(5),2N-02-01(1) 15LBS - 12IN X 12IN X 12IN

[MECCO MC-19 PNEUMATIC AIR IMPACT PRESS] 3/4 TON FORCE 20" HIGH NEEDS CONTROLS - MANUFACTURER: MECCO MODEL: MC-19 CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THIS PRESS IS IN FAIR COSMETIC CONDITION WITH LOTS OF SURFACE RUST AS WELL AS CHIPPED/MISSING PAINT. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: WE WERE ABLE TO ADJUST THE IMPACT ADJUSTMENT AND VERIFY THE PRESS RAISES AND LOWERS, AND THE CLAMP EXTENDS/RETRACTS WHEN AIR IS PUT TO THE HOSE ENDS. IT MAY TAKE SOME EFFORT TO REMOVE THE TOOLING (USE PENETRATING OIL!) AND TO MOVE/ADJUST THE STAND. NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) MECCO MACHINE MC-19 IMPACT PRESS (1) SET OF TOOLING AS SHOWN SPECIFICATIONS: MANUFACTURER: MECCO MACHINE LTD. MODEL: MC-19 IMPACT PRESS BENCHTOP MODEL, BOLT-DOWN MOUNT AIR-POWERED MAX. IMPACT: 3/4 TON COLUMN HEIGHT: 20" THROAT DEPTH: 3-7/8" THROAT HEIGHT: 11-3/4" MAX. TABLE SIZE: 4" SQUARE T-SLOT TABLE REQUIRES 40-90 PSI IMPACT SPRINGS CAN BE SWITCHED TO ADJUST IMPACT FORCE HAND-ADJUSTABLE IMPACT FORCE CONSISTENT IMPACT INDEPENDENT OF PRODUCT THICKNESS WORKPIECE IS HELD PRIOR TO IMPACT CAN BE A MANUAL ARBOR PRESS IF YOU DISCONNECT AIR AND INSTALL A HANDLE MUST HAVE NEW ANTI-TIEDOWN CONTROLS INSTALLED FOR USE! CYLINDER REQUIRES OIL LUBRICATION SKU: W46D008 2A-05-01(1) 51LBS - 25IN X 18IN X 11IN

INDUSTRIAL STEEL BLACK DOUBLE WHEEL SWIVEL 2" ROLLING CASTER WHEELS (4) - MANUFACTURER: UNKNOWN MODEL: DOES NOT APPLY DESCRIPTION: INDUSTRIAL STEEL BLACK DOUBLE WHEEL ROLLING CASTER WHEELS SWIVEL TYPE DOUBLE WHEEL WHEEL DIAMETER: 2" WHEEL WIDTH: 1.75" TOTAL HEIGHT: 2.75" BASE DIMENSIONS: 3.75" X 2.50" BOLT HOLE WIDTH: 1.75" X 3"

[2.75" DIAMETER] SIEMENS 8WD4 COMPACT MODULAR 3-SEGMENT SIGNAL TOWERS (2) - MANUFACTURER: SIEMENS MODEL: 8WD4 MODULAR SIGNAL TOWER SEGMENTS: RED, GREEN, ORANGE DEGREE OF PROTECTION: IP65 CONNECTION: SCREW ELEMENTS VOLTAGE RATING: TOTAL LENGTH: 15.5" DIAMETER: 2.75" VOLTAGE RATING: 230V MAX MADE IN GERMANY

[SOMACA SOMMER & MACA] DBM-84 VERTICAL BELT SANDER 84"L X 2"W 3450-RPM 2-HP 1-PH. SPECIFICATIONS: MANUFACTURER: SOMACA SOMMER & MACA MODEL: DBM-84 TYPE: VERTICAL BELT: WIDTH: 2" LENGTH: 84" MOTOR: HP: 2 RPM: 3450 V: 115/208-230 SINGLE PHASE. CONDITION: USED. THIS ITEM COMES IN NON-ORIGINAL PACKAGING. IT HAS SCUFFS, SCRATCHES, SURFACE RUST AND A RUSTED HOLE FROM NORMAL USE. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: WHEN POWER WAS APPLIED, THIS ITEM RAN VERY SMOOTHLY. IT WAS NOT TESTED WITH A BELT. THE OTHER TWO PULLEYS NOT ATTACHED TO THE MOTOR MANUALLY SPUN EASILY WITHOUT PROBLEMS. THIS SANDER DOES NOT COME EQUIPPED WITH A BELT OR A NON-SLIP BAND (AS SHOWN, SEPARATED). THE PUMP DOES NOT WORK, AND WILL HAVE TO BE REPLACED. THERE IS ALSO A RUSTED HOLE ON ONE SIDE OF THE TANK WHERE THE WATER CAN ESCAPE. IT WILL BE THE RESPONSIBILITY OF THE BUYER TO REPLACE THE PUMP AND REPAIR THE HOLE. NO FURTHER TESTING WAS PERFORMED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) SOMACA SOMMER & MACA DBM-84 VERTICAL BELT SANDER 84"L X 2"W 3450-RPM 2-HP 1-PH. SKU: W49L001 5H-02-01(1) 350LBS - 48IN X 40IN X 74IN

RW&D 636 TOX AIR-OVER-HYDRAULIC PRESS 40KN 4 TONS WORKS-ISH. MANUFACTURER: RW&D MACHINE AND ENGINEERING RWD MODEL: 636. THIS PRESS HAS LOTS OF MINOR BLEMISHES FROM USE. THERE ARE SCUFFS/SCRATCHES AND ADHESIVE LABEL RESIDUES HERE AND THERE ALL OVER. SOMETHING HAS BEEN UNBOLTED FROM BEHIND THE PRESS IN THE WORKING AREA, BUT WE ARE NOT SURE WHAT THAT WAS. THE WIRING IN THE CONTROL ELECTRONICS ENCLOSURE HAS BEEN OPENED; WE ARE NOT SURE IF IT WAS TAMPERED WITH. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS PRESS IS IN PARTIAL WORKING CONDITION. THE NATIONAL INSTRUMENTS SOFTWARE HAS AN EXPIRED LICENSE, AND WE ARE NOT SURE IF THAT IS RELATED TO THE ERROR WE FOUND. WHEN THE PRESS FIRST STARTS, THE CRIMP PRESS APP LOADS AND GIVES AN ERROR IMMEDIATELY: "THE FOLLOWING ERROR OCCURRED: VISA CLEAR IN CRIMPSTATION.VI AT SEQUENCE: INIT OPENCOMPORTS" WE ARE NOT SURE WHAT THIS MEANS. WHEN RESUME IS PRESSED, THE ALARM SOUNDS AND THE SOFTWARE CLOSES ITSELF. THE VERY GOOD NEWS IS: BOTH THE TOP AND BOTTOM AIR CYLINDERS RAISE AND LOWER WHEN AIR IS APPLIED TO THEIR PORTS. THE BARCODE SCANNER SCANS. THE LASER DISTANCE SENSORS SENSE. THE PNEUMATIC PRESSURE SENSOR SHOWS A READING. THE TOUCH SCREEN RESPONDS TO TOUCH INPUTS. NO OTHER TESTING WAS DONE. THIS MACHINE WILL NOT INITIALIZE ITS SOFTWARE PROPERLY. WE ARE CONFIDENT IT IS ABLE TO FUNCTION AS A PNEUMATIC PRESS. WE ARE NOT ABLE TO SUPPORT THE SOFTWARE AT ALL, SORRY! NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) RW&D 636 4-TON PRESS (1) OPERATIONS MANUAL SPECIFICATIONS: MANUFACTURER: RW&D MACHINE & ENGINEERING, INC. MODEL: 636 LID CRIMP CELL AIR-OVER-HYDRAULIC PRESS 4-POST PRESS CAPACITY: TO 40KN / 4 TONS @ 10 BAR AIR PRESSURE FACILITY REQUIREMENTS: 120V 60HZ 1PHASE 10A AND COMPRESSED AIR PRESS POST THICKNESS: 44MM PRESS PLATE THICKNESS: 45MM TOP, 48MM BOTTOM PRESS PLATE SIZE: 24" X 14" AREA BETWEEN POSTS: 19" X 8" TOP PRESS PLATE FRAME: 31 AND 25MM THICK PLATE STEEL OPERATED BY WINDOWS PC USING NATIONAL INSTRUMENTS INTERFACE (PLEASE READ TEST NOTES!) 19" COLOR TOUCHSCREEN LCD DISPLAY (2) EMERGENCY STOP SWITCHES VISUAL AND AUDIBLE ALARM STACK TOWER ON TOP KEYENCE SL-V28HM-T SAFETY LIGHT CURTAIN MICROSCAN FIS-6300-5001G MINI HAWK BARCODE READER UPPER PRESS PLATE DRIVEN BY TOX PRESSOTECHNIK KRAFT-PAKET CYLINDER LOWER PRESS PLATE HAS A REGULAR PNEUMATIC CYLINDER TO LIFT FIXTURES TOX CYLINDER TYPE: S 04.00.300.440.US TOTAL STROKE: 300MM POWER STROKE: 44MM MAXIMUM PRESSURE INPUT: 10 BAR SKU: W42D012 6-BILR1(1)

2018 SWEP B25HX16/1P-SN-S INDUSTRIAL HEAT EXCHANGER MAX-WORKING-PRESSURE:1.1 MPA CONSTRUCTION: 316/316L STAINLESS STEEL PLATES, COPPER BRAZING LENGTH: 20.75" WIDTH: 4.5" HEIGHT: 3.5" MAX WORKING TEMPERATURE: 135 C MAX WORKING PRESSURE: 1.1 MPA TEST PRESSURE: 2.1 MPA VOLUME: 0.798L PRIMARY, 0.912L SECONDARY MIN WORKING TEMPERATURE: -196C YEAR OF MANUFACTURER: 2018

[PULNIX TM-440X] PULNIX TM-440X 422X489 PIXEL MACHINE VISION CAMERA W/KLA PERISCOPE ARM. MACHINE VISION CAMERA SYSTEM: EIA (NTSC) IMAGE SENSOR: MN3734SK PIXELS: 422 H X 489 V RESOLUTION: 310 TV LINES H X 350 TV LINES V LENS: 20MM DIMENSIONS: 4.75" X 1.75" X 1.5". KLA ASSY. #: 740-905000-00 MACHINE VISION PERISCOPE/ X-Y STAGE ATTACHMENT LENGTH: 12.25". CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THE CAMERA ASSEMBLY IS IN GOOD, USED CONDITION WITH SOME MINOR SCUFFS AND SCRATCHES FROM THE PREVIOUS INSTALLATION. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THE ASSEMBLY WAS REMOVED FROM A DECOMMISSIONED MACHINE. NO FURTHER TESTING WAS PERFORMED AFTER REMOVAL. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. SKU: X07B003 1C-01-01(1) 5LBS - 16IN X 12IN X 6IN

CONVEYOR TECHNOLOGIES 1 METER ENCLOSED PCB SHUTTLE CONVEYOR

RUBBERMAID 1046 TILT TRUCK 2 1/2 CUBIC YARDS

29 SOUTH WELD 10N47L #7 LONG ALUMINA NOZZLE 7/16" MANUFACTURER: SOUTH WELD MODEL: 10N47L DESCRIPTION: LONG ALUMINA CERAMIC GAS CUP NOZZLE SPECIFICATIONS: MANUFACTURER: SOUTH WELD MODEL: 10N47L DESCRIPTION: LONG ALUMINA CERAMIC GAS CUP NOZZLE SKU: V03H019 2O-02-01(1) 4LBS - 7IN X 7IN X 7IN

2008 GRUNIG G-DRY 570 HOT AIR SCREEN PRINT DRYING CABINET FOR LARGE FORMAT G-570I - MANUFACTURER: GRUNIG MODEL: G-570I CONDITION: USED. THIS CABINET IS IN FAIR COSMETIC CONDITION. THE RIGHT DOOR WINDOW HAS BEEN REPLACED WITH A FROSTED PIECE OF PLEXIGLASS, AND THE LEFT WINDOW HAS A CRACK AT THE BOTTOM. INSIDE, AND OUTSIDE ESPECIALLY ON THE DOORS, THERE IS A LOT OF PAINT RESIDUE FROM THE PREVIOUS OWNER. THE UPPER PART OF THE RACKS TO HOLD FRAMES ARE MISSING (THEY WERE USING THIS WITH ROLL-IN CARTS AND ADDED TRACKS ON THE FLOOR). THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS CABINET IS IN GOOD WORKING CONDITION. WHEN SET TO 45O IT REACHED AND HELD TEMPERATURE WITHIN A DEGREE. FOR CURIOSITY, WE SET 55O AND SHUT OFF WHEN IT WAS READING 50O. AT 45O, THE OUTSIDE WAS WARM TO TOUCH. THE FANS VIBRATE SLIGHTLY. NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) GRUNIG G-DRY 570 SCREEN DRYER SPECIFICATIONS: MANUFACTURER: GRUNIG-INTERSCREEN AG TYPE: G-570I G-DRY 570 HOT AIR CONVECTION DRYER CABINET IDEAL FOR VERTICAL DRYING OF LARGE FORMAT SCREENS, COATED OR WET MAXIMUM FRAME SIZE: 2M X 1.9M MAXIMUM TEMPERATURE: 45OC/113OF SPACE FOR AT LEAST 10 STENCILS 2-3/4" WIDE TRACKS ON FLOOR, 80" LONG DOOR OPENING: 43-1/2"W X 74"H VENTILATED TOP/FRONT FOR VAPOR ESCAPE DUAL FAN/HEATERS IN TOP OF CABINET TRANSPARENT DOORS FOR GOOD INTERIOR VIEWS ALUMINUM T-SLOT FRAME CONSTRUCTION SWING-OPEN DOORS FOR EASY ACCESS DIGITAL TEMPERATURE CONTROLLER POWER REQUIREMENT: 3PHASE 60HZ 220V 8A (3KW) MANUFACTURED IN 2008 SKU: Y24D002 6-BILR2(1) 975LBS - 110IN X 72IN X 102IN

[LEGACY FROM WELDCRAFT] 10N28LGC COLLET BODY 1/8" - LOT OF 75 - NEW - MANUFACTURER: LEGACY MODEL: 10N28LGC CONDITION: NEW. COMES IN ORIGINAL PACKAGING. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (15) PACKS OF (5) LEGACY FROM WELDCRAFT 10N28LGC COLLET BODYS SPECIFICATIONS: MANUFACTURER: LEGACY MODEL: 10N28LGC COLLET BODY 1/8" 3.2MM PACK OF 5 SKU: R13C020 1B-11-02(1) 5LBS - 8IN X 8IN X 7IN

1998 DELTECH D-3000-CF AIR FILTER HOUSING 3000 SCFM 200 PSIG STEEL SILVAN TANK. MANUFACTURER: DELTECH MODEL: D-3000-CF AIR FILTER HOUSING RATED FLOW: 3000 SCFM RATED PRESSURE: 200 PSIG (14 BARG) MAX. INLET TEMPERATURE: 150 OF STEEL TANK FLANGE FITTINGS GATE VALVE ON BOTTOM DIFFERENTIAL PRESSURE METER REPLACEABLE FILTER ELEMENT (SPECIFIES D-3000-CFE) OVERPRESSURE VALVE: HYDRO-SEAL SIZE 2 2" SEAT PRESSURE: 145 PSI CAPACITY: 1195 CFM TANK: SILVAN INDUSTRIES 80DE526A MAWP: 225PSI @ 105OF MDMT: -20OF @ 225 PSI BUILT: 1998 SKU: W43D005 5A-05-04(1) 675LBS - 48IN X 40IN X 90IN

[VITRONICS SOLTEC XPM31] HEATER ASSEMBLY W/ HEATER PANEL. MANUFACTURER: VITRONICS SOLTEC. MODEL: XPM31. DESCRIPTION: HEATER ASSEMBLY W/ HEATER PANEL. SKU: V39H009. 5A-18-04(12) 55LBS - 37IN X 19IN X 16IN.

[HARRINGTON HOISTS & CRANES] 6-TON PNEUMATIC CHAIN HOIST AIR-PRESSURE:60~90PSI 30'-CHAIN SPECIFICATIONS: MANUFACTURER: HARRINGTON HOISTS & CRANES MODEL: UNKNOWN CAPACITY: 6 TON OPERATION: PNEUMATIC CHAIN HOIST 30' CHAIN AIR PRESSURE: 60 ~ 90 PSI 410 ~ 620 KPA SKU: X02L001 5A-14-02(1) 360LBS - 48IN X 40IN X 25IN

[19] K-O CONCEPTS LCR-1 RACK-MOUNTED REFRIGERATING/HEATED RECIRCULATOR - PARTS - MANUFACTURER: K-O CONCEPTS MODEL: LCR-1 CONDITION: FOR PARTS OR NOT WORKING. COMES IN NON-ORIGINAL PACKAGING. THIS CHILLER IS IN FAIR COSMETIC CONDITION WITH SCUFFS/SCRATCHES/RESIDUES FROM PIROR USE. THERE IS GREEN AND BLACK RESIDUE ON THE HEATER AND GREEN FLECKS IN THE BOTTOM OF THE RESERVOIR. THE HEAT EXCHANGER HAS INSULATION PEELING OFF THE SIDES. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS SYSTEM IS IN PARTIAL WORKING CONDITION. THE PUMP GIVES VERY WEAK FLOW. THE HEATER HEATS THE WATER IN THE RESERVOIR. THE CONTROL RESPONDS TO USER INPUTS TO CHANGE THE SETPOINT. THE EXHAUST FAN RUNS QUIETLY. THE COMPRESSOR DID NOT RUN, POSSIBLY DUE TO LOW WATER FLOW OR LACK OF AN INPUT ON THE REAR PANEL CONNECTORS, WE ARE NOT SURE. THE TEMPERATURE READING JUMPED AND CHANGED WHEN THE THERMOCOUPLE WIRES WERE TOUCHED, WE ARE NOT SURE WHY. WE ARE NOT SURE WHAT ELSE MAY BE WRONG WITH THIS UNIT. NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) K-O CONCEPTS LCR-1 CHILLER SPECIFICATIONS: MANUFACTURER: K-O CONCEPTS, INC. MODEL: LCR-1 P/N: 25422300 REFRIGERATED/HEATED CIRCULATOR WATER CHILLER/HEATER MOUNTS IN 19" EQUIPMENT RACK CARRY HANDLES FRONT-AND-BACK QUICK RELEASE LIQUID CONNECTIONS DIGITAL CONTROLLER R-134A REFRIGERATION DIGITAL CONTROLLER: WATLOW 96A0-CDAA-00GR COMPRESSOR: EMBRACO EM20HHR3 PUMP: IWAKI MD-6Z-220/240 MAGNET PUMP, RATED 1.5 GPM/6.9FT. HEAD POWER: 120/230V 50/60HZ 1PHASE 2.5A NOT WORKING PROPERLY! SKU: W52D023 1E-03-03(1) 56LBS - 25IN X 25IN X 13IN

[030.078.125] KABELSCHLEPP 030.078.125 ENERGY E-CHAINS (2) - MANUFACTURER: KABELSCHLEPP MODEL: 030.078.125 CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THESE E-CHAINS HAVE SCUFFS AND SCRAPES FROM PREVIOUS USE. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THESE E-CHAINS BEND AND FLEX WITH NO KINKS. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (2) KABELSCHLEPP 030.078.125 ENERGY E-CHAINS SPECIFICATIONS: MANUFACTURER: KABELSCHLEPP MODEL: 030.078.125 FLEX CABLE CARRIER LENGTH: 1066MM (42") OUTER DIMS: 95.25MM (3-3/4") INNER DIMS: 76.2MM (3") MATERIAL: NYLON

UNBRANDED MOTORIZED BELT CONVEYOR INCLINE 75"L X 43"W X 41.5"H W/ NORD 0.25HP MOTOR. MANUFACTURER: UNBRANDED. MODEL: 63L/4 CUS. CONDITION: USED. THIS CONVEYOR INCLINE IS IN GOOD COSMETIC CONDITION WITH SCUFFS, SCRATCHES, AND SOME GENERAL WEAR FROM REGULAR INDUSTRIAL USE. THE COVER FOR THE CHAIN DRIVE IS MISSING AND NOT INCLUDED. THE TOP CHAIN PULLEY WOBBLES SLIGHTLY WHILE RUNNING. THE BELT IS IN GOOD CONDITION WITH SOME WEAR LINES ALONG THE LENGTH (SEE PHOTO). COMES IN NON-ORIGINAL PACKAGING. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: WE CONNECTED THIS CONVEYOR MOTOR TO POWER AND TURNED IT ON TO OBSERVE THE CONVEYOR RUN SMOOTHLY. THERE IS A SLIGHT WOBBLE IN THE TOP CHAIN PULLY WHEN RUNNING. THE CONVEYOR BELT RUNS STRAIGHT AND TRUE. NO ADDITIONAL TESTING WAS PERFORMED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) MOTORIZED CONVEYOR INCLINE 75"L X 43"W X 41-1/2"H W/ NORD 63L/4 CUS 0.25HP MOTOR. SPECIFICATIONS: MANUFACTURER: UNBRANDED / NORD. MODEL: DOES NOT APPLY / 63L/4 CUS. DESCRIPTION: MOTORIZED BELT CONVEYOR INCLINE WITH MOTOR. CONVEYOR OVERALL DIMENSIONS: 75"L X 43"W X 41-1/2"H. FRONT HEIGHT: 12". BELT WIDTH: 40-3/4". 1-3/4" T-SLOT CONSTRUCTION. MOTOR NORD MTR. 63L/4 CUS NO. 31711502 / 13340893 SYST.DV155J 3PH SF: 1.15 DUTY 1 IP 55 INS: F PF: 0.71 FR: 63 AMB: 40 DEGREES C ENCL: TEFC DP CODE E 0.250 HP 0.180 KW 1680 RPM 60HZ 230/460 YY/Y V 1.12/0.56A. SKU: Y08H001 5J-03-05(1) 310LBS - 83IN X 53IN X 50IN

[USED] HANSHIN CHAIN HSP0450-1B 59.5" LONG ENERGY CHAIN MANUFACTURER: HANSHIN CHAIN MODEL: HSP0450-1B ENERGY CHAIN MATERIAL: ENGINEERING PLASTIC LENGTH: 59.5" WIDTH: 2 1/8" HEIGHT: 1 3/8" MOVING VELOCITY: BELOW 180 M/MIN DIAMETER OF CABLE HOSE: LESS THAN 36 MM OPERATING TEMPERATURE: -25 TO 100 C TENSION: 190 (IN DRY), 120 (IN MOISTURE) N/MM SQUARED STRETCH: 4 (IN DRY), 6 (IN MOISTURE) % ELASTICITY: 10000 (IN DRY), 7000 (IN MOISTURE) N/MM SQUARED SLIDING FRICTION: 0.4 (NON GREASED) BASIC COLOR: BLACK INCLUDED: (1) HANSHIN CHAIN HHSP0450-1B 59.5" LONG ENERGY CHAIN

MAYHEW 12405 BALTIMORE GUARDIAN 1" X 12" HANDGUARD FLAT COLD CHISELS - MANUFACTURER: MAYHEW MODEL: 12405 CONDITION: NEW. COMES IN FACTORY ORIGINAL PACKAGING. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (9) MAYHEW 12405 BALTIMORE GUARDIAN 1" X 12" HANDGUARD CHISELS SPECIFICATIONS: MANUFACTURER: BALTIMORE GUARDIAN MAYHEW MODEL: 12405 HANDGUARD CHISELS SIZE: 1" X 12" TIP STYLE: FLAT TIP WIDTH: 1-1/2" GUARD WIDTH: 3-3/8" CHISEL MATERIAL: STEEL HANDLE COLOR: ORANGE SKU: Q12Y009 1D-08-01(1) 18LBS - 18IN X 12IN X 12IN

(2) LARGE 6" X 2" HEAVY INDUSTRIAL ROLLING SWIVEL CASTER WHEELS W/ LOCKS. SWIVEL TYPE WHEEL DIAMETER: 6" WHEEL WIDTH: 2" TOTAL HEIGHT: 7.50" BASE DIMENSIONS: 4" X 4.50" BOLT HOLE WIDTH: 3.50" X 2.75". THE CASTERS ARE IN USED CONDITION WITH SCUFFS, SCRATCHES, AND SOME RESIDUE FROM PREVIOUS USE. THE WHEELS ROLL AND THE SWIVEL BASE WORKS AS INTENDED.

DATAMAX O'NEIL H-4212X 4" THERMAL LABEL PRINTER (240X320 LCD BACKLIT DISPLAY, 600 DPI RESOLUTION, 12 IPS MAX PRINT SPEED, 16.4X12.6X19.3 DIMENSIONS) INTEGRATED WITH PANTHER INDUSTRIES INDUSTRIAL AUTOMATED LABEL APPLICATOR STAND (17" X 15.5" X 14.25" THERMAL LABEL PRINTER SURFACE AREA, 68" H X 45.75" W X 34.5"D TOTAL DIMENSIONS, 46" ADJUSTABLE TRAVEL, 3 CASTER WHEELS WITH 5.5" CASTER HEIGHT). THE PRINTER IS MISSING ITS FRONT COVER.

AIMCO-URYU U-410S INLINE NON-SHUTOFF PNEUMATIC AIR 3/8" SQUARE DRIVE U-WRENCH. MANUFACTURER: AIMCO URYU MODEL: U-410S. AIR HOLE SIZE: 1/4" AIR INLET THREAD N.P.T.: 1/4" FREE SPEED-RPM: 10,000 NOISE LEVEL: 67DB(A) SQUARE DRIVE: 3/8" CLUTCH TYPE: NON-SHUT OFF TORQUE RANGE-FT LBS:5.0 ~7.2 TORQUE RANGE: NM: 7.0~10 TOOL PULSE: 5-7.2 FT LB

[NUARC TLCTS5260H221606KW] SCREEN EXPOSURE SYSTEM. MANUFACTURER: NUARC. MODEL: TLCTS5260H221606KW. CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THIS SCREEN EXPOSURE SYSTEM IS IN GOOD COSMETIC CONDITION WITH SCUFFS AND SCRATCHES TO THE LOWER ENCLOSURE FROM REGULAR COMMERCIAL USE BUT NOTHING SIGNIFICANT. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: WE POWERED ON THIS EXPOSURE SYSTEM TO OBSERVE THE LED DISPLAY TURN ON AND OFFER MENU ITEMS. AFTER PUSHING THE START BUTTON THE LED DISPLAY INDICATED THAT THE VACUUM WAS ON AND WE COULD OBSERVE THE TOP COVER VACUUMING DOWN AND THE FANS BEGAN TO RUN. NEXT, WE OBSERVED THE LIGHT TURN ON WITHIN THE UNIT AND AFTER A SHORT PERIOD TURNED OFF AND THE LED DISPLAY READ EXPOSURE COMPLETE. WE PRESSED THE OK BUTTON AND THE DISPLAY READ COOLING LAMP WITH A COUNTDOWN. WE CONFIRMED THAT BOTH LAYERS OF THE TOP ASSEMBLY COULD BE RAISED, LOWERED, AND LOCKED AS DESIGNED. NO ADDITIONAL TESTING WAS PERFORMED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) NUARC TRI-LIGHT CTS DUAL PURPOSE COMPUTER-TO-SCREEN EXPOSURE SYSTEM 142X163 CM SPECIFICATIONS: MANUFACTURER: NUARC MODEL: TLCTS5260H221606KW DESCRIPTION: TRI-LIGHT CTS DUAL PURPOSE COMPUTER-TO-SCREEN EXPOSURE SYSTEM BLANKET & VACUUM ADVANCED DESIGN ELIMINATES THE NEED FOR A VACUUM HOSE CONNECTION TO THE BLANKET EXCEPTIONALLY FLEXIBLE AND RESILIENT MATERIAL ENSURES INTIMATE CONTACT AND BLANKET LONGEVITY GAS SHOCKS SIMPLIFY BLANKET FRAME OPENING AND CLOSING THE OIL-FREE PUMP IS FAST, QUIET, AND EFFICIENT UNIQUE MANIFOLD SYSTEM ENSURES INTIMATE CONTACT BY DRAWING VACUUM EVENLY AROUND THE PERIMETER OF THE BLANKET FRAME THE VACUUM RELEASE SYSTEM INSTANTLY RELEASES VACUUM CERTIFICATION CE & UL COMPLIANT: BUILT TO SPECIFICATIONS ESTABLISHED BY THE EUROPEAN COMMITTEE FOR STAND COMPUTER-TO-SCREEN (CTS) FEATURE ELIMINATION OF BLANKET DRAWDOWN PRODUCES FASTER COMPUTER-TO-SCREEN EXPOSURES EXPOSES SCREENS THAT HAVE BEEN GENERATED BY A COMPUTER-TO-SCREEN (CTS) SYSTEM RACKS ARE ADJUSTABLE TO ACCOMMODATE DIFFERENT SIZE SCREENS SEPARATES THE SCREEN FRAME FROM THE BLANKET TO PREVENT SMEARING AND DISTORTION CONTROLLER/INTEGRATOR FOR SCREEN EXPOSURES COMPUTER-CONTROLLED AND FULLY PROGRAMMABLE JOB RECALLTM ALLOWS THE STORAGE AND RECALL OF NUMEROUS VACUUM AND SCREEN EXPOSURE VALUES LIGHT INTEGRATOR ENSURES PRECISE SCREEN EXPOSURE TIMES TOUCH-SCREEN PANEL WITH ALPHANUMERIC DISPLAY DESIGN & CONSTRUCTION 104 CM (41") WORKING HEIGHT FOR NO-STEP ACCESS 9.5 MM (3/8") THICK OPTICALLY-CLEAR PLATE GLASS IT CAN BE DISASSEMBLED TO FIT THROUGH A 76 CM (30") WIDE OPENING FRAME LATCHES ARE MADE WITH STATE-OF-THE-ART MATERIAL FOR DURABILITY, LONGEVITY, AND OPERATOR COMFORT FULLY-ENCLOSED, HEAVY-DUTY STEEL CABINET LIGHT-LOCTM AUTOMATICALLY TURNS OFF THE SCREEN EXPOSURE LIGHT SOURCE IF THE BLANKET FRAME IS OPENED REMOVABLE COVERS PROVIDE EASY ACCESS TO COMPONENTS TO CLEAN OR REPLACE SERVICEABLE ITEMS LIKE SCREEN PRINTING LAMPS SELF-CONTAINED DESIGN SPEEDS PRODUCTION BY ALLOWING PLACEMENT IN LIGHT-SAFE SCREEN-COATING ROOMS SQUARE TUBULAR STEEL WELDED FRAME LIGHT SOURCE FOR SCREEN EXPOSURES THE LAMP DRAWER MAKES THE SCREEN EXPOSURE LAMP EASY TO ACCESS AND CHANGE MULTI-POINT METAL-HALIDE UV SCREEN EXPOSURE LAMPS EXCEL ON ALL EMULSIONS: DIRECT, CAPILLARY, AND INDIRECT POINT-LIGHT SOURCE PROVIDES MAXIMUM COLLIMATION AND OPTIMUM COVERAGE TO HOLD FINE LINES AND DOTS DURING SCREEN EXPOSURE PROPORTIONAL TEMPERATURE CONTROL (PTC) TURNS COOLING FANS ON AND OFF TO KEEP THE SCREEN EXPOSURE LAMP AT OPTIMUM OPERATING TEMPERATURE SCREEN EXPOSURE LAMP IDLES AT 1 KW WHEN NOT EXPOSING SCREENS SYSTEM 631 SHUTTERED MULTI-SPECTRUM METAL-HALIDE SCREEN EXPOSURE LAMP PRODUCES FAST, EFFICIENT USER-SELECTED EXPOSURES OF 6 KW, 3 KW, OR 1 KW SCREEN EXPOSURE AREA 132 X 152 CM (52" X 60") MAXIMUM SCREEN FRAME SIZE WHEN USING THE VACUUM WITH CONVENTIONAL SCREENS 142 X 163 CM (56" X 64") MAXIMUM SCREEN FRAME SIZE FOR RACK-MOUNTED CTS-GENERATED SCREENS (THE RACK WILL ALSO ACCOMMODATE TWO 64 X 91 CM (25" X 36") OR FOUR 58 X 79 CM (23" X 31") SCREEN FRAMES SIMULTANEOUSLY) COMPATIBLE WITH THE TRI-LOC & DOUBLE TRI-LOC RAPID REGISTRATION SYSTEMS FROM M&R ELECTRICAL REQUIREMENTS 208/230 V, 1 PH, 32/29 A, 50 HZ, 7 KW 208/230 V, 1 PH, 30/28 A, 60 HZ, 6 KW MAXIMUM SCREEN FRAME SIZE (CTS RACK) 142 X 163 CM (56" X 64") MAXIMUM SCREEN FRAME SIZE (VACUUM BLANKET) 132 X 152 CM (52" X 60") OVERALL SIZE (H X W X D) 2 117 X 188 X 180 CM (46" X 75" X 71") VACUUM FRAME SIZE 152 X 174 CM (60" X 68.5") WATTAGE 6 KW SKU: Y26H029 6-BILR3(1) 1350LBS - 81IN X 77IN X 56IN

[USED] SPARKS BELTING MHD1.9-17.36-30-VOF MOTORIZED CONVEYOR PULLEY 24VDC. MANUFACTURER: SPARKS BELTING. MODEL: MHD1.9-17.36-30-VOF. CONVEYOR ROLLER MOTORIZED PULLEY. GROOVES: 2. VOLTAGE RATING: 24VDC. ROLLER LENGTH: 17.5". TOTAL LENGTH: 19.25". DIAMETER: 1.91". ACTUATION: BALL BEARING, ELECTRONIC HEX. DIAMETER: 0.43". THREAD DIAMETER: 0.44". FINISH/COLOR: SILVER. COMES IN NON-ORIGINAL PACKAGING. THE ROLLER IS IN GOOD, USED CONDITION WITH SOME SCUFFS, SCRATCHES, AND STICKER RESIDUE FROM PREVIOUS INSTALLATION. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). THE ROLLER WAS REMOVED FROM A DECOMMISSIONED MACHINE. NO FURTHER TESTING WAS PERFORMED AFTER REMOVAL. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN.

YG 16020HC Y4TRA-14004 14MM 4-FLUTE END MILL (5) - MANUFACTURER: YG MODEL: 16020HC CONDITION: USED. COMES IN ORIGINAL OPEN BOX PACKAGING. THESE END MILLS HAVE MINOR MARKINGS FROM NORMAL USE AND SHOW NO MAJOR DEFECTS THAT WOULD AFFECT FUNCTIONALITY. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: THESE END MILLS WERE NOT TESTED DUE TO A LACK OF NECESSARY RESOURCES BUT WERE CAREFULLY INSPECTED FOR FLAWS. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (5)HC Y4TRA-14004 14MM 4-FLUTE END MILL REGULAR LENGTH SPECIFICATIONS: MANUFACTURER: YG MODEL: 16020HC DESCRIPTION: 14MM 4-FLUTE END MILL REGULAR LENGTH SIZE: 14.0MM SHANK DIAMETER: 1/2" FLUTE DIAMETER: 1-3/8" OVERALL LENGTH: 3-3/8" COATING: TIAIN-FUTURA FLUTES: 4 SKU: U04U018 1A-03-01-02(1) 0LBS - 6IN X 6IN X 4IN

[DODGE 41511265TR] V/D VARI SLIDING DISC KIT SIZE 050 SKU: X03H039 1D-20-02(1) 3LBS - 8IN X 8IN X 7IN

[USED] MST 9602-0400 FMK SATELLITE FTT DIGITAL CONTINUOUS GAS MONITORING SYSTEM MANUFACTURER: MST MODEL: 9602-0400 DESCRIPTION: CONTINUOUS GAS MONITORING SYSTEM DISPLAY: DIGITAL 12 - 24 VDC TYPE: CONTINUOUS GAS NO SENSOR SKU: X46G013

[OMRON K3TS-SD11B] INTELLIGENT SIGNAL PROCESSOR NO OUTPUTS 100-240V POWER SUPPLY. MANUFACTURER: OMRON MODEL: K3TS-SD11B. THIS UNIT IS IN GOOD COSMETIC CONDITION WITH MINOR BLEMISHES FROM PRIOR USE/INSTALLATION/REMOVAL. INCLUDES: (1) OMRON K3TS-SD11B SIGNAL PROCESSOR. SPECIFICATIONS: MANUFACTURER: OMRON MODEL: K3TS-SD11B INTELLIGENT SIGNAL PROCESSOR MEASUREMENT RANGE: 4-20MA, 1 TO 5V OR -9.999 TO 9.999V 1.04MS SAMPLING TIME SET VALUE LED DISPLAYS WITH NO OUTPUTS SUPPLY VOLTAGE: 100-240VAC, 50/60HZ 15VA MAX.

[NEW] IRWIN BI-METAL HOLE SAW SET: INCLUDES (1) 373058BX 5/8" (16MM), (3) 373078BX 7/8" (22MM), (1) 373118BX 1-1/8" (29MM), (1) 373138BX 1-3/8" (35MM). CONDITION: NEW. COMES NEW IN ORIGINAL PACKAGING. MANUFACTURER: IRWIN. SKU: U50U012.

1998 FLATPLATE SC8 INDUSTRIAL HEAT EXCHANGER STAINLESS STEEL PLATES, COPPER BRAZING LENGTH: 12.25" WIDTH: 5" HEIGHT: 3.25" MAX WORKING TEMPERATURE: 350(177) C MAX WORKING PRESSURE: 450(31) BAR VOLUME: 0.991L PRIMARY, 1.076L SECONDARY

DEPRAG 343-521U MINIMAT STRAIGHT PUSH-TO START PNEUMATIC SCREWDRIVERS (2) MANUFACTURER: DEPRAG MODEL: 343-521U PART NUMBER: 386364C STRAIGHT STYLE PNEUMATIC SCREWDRIVER MINIMUM TORQUE: 0.3 NM TORQUE MAX SOFT PULL-UP: 5 NM MAXIMUM HARD PULL-UP: 5 NM IDLING SPEED: 500 RPM SCREWS: M5 CHUCK DIAMETER: 1/4" CONNECTION: NIPPLE NIPPLE DIAMETER: 0.33"

MARKAL 86544 THERMOMELT HEAT STICK TEMP 225-F 107-C (12) - MANUFACTURER: MARKAL MODEL: 86562 CONDITION: NEW OTHER. THESE HEAT STICKS ARE IN A NEW AND UNUSED COSMETIC CONDITION AND COME IN THE ORIGINAL MARKAL BOX THAT CONTAINS 12 STICKS. THE BOX SHOWS SOME MINOR WEAR FROM STORAGE AND THERE IS TAPE ON THE OUTSIDE OF THE BOX. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (12) MARKAL 86544 THERMOMELT HEAT STICK TEMP 225-F 107-C SPECIFICATIONS: MANUFACTURER: MARKAL MODEL: 86544 DESCRIPTION: THERMOMELT HEAT STICK TEMP 225-F 107-C THE BIG STICK! SKU: V03H030 2F-03-02(1) 2LBS - 8IN X 8IN X 4IN

URYU US-LT30PB-05 PNEUMATIC AUTO SHUT-OFF 1/4" AIR SCREWDRIVER/NUTRUNNER - MANUFACTURER: URYU MODEL: US-LT30PB-05 CONDITION: USED. COMES IN NON ORIGINAL PACKAGING. THIS SCREWDRIVER IS IN GOOD COSMETIC CONDITION WITH FEW BLEMISHES AND SCRATCHES FROM PREVIOUS USE. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: TESTS INCLUDED PLUGGING IN THE SCREWDRIVER TO AN AIR LINE HOSE. THE SCREWDRIVER WORKED GREAT WITH NO ISSUES IN THE FORWARD POSITION AS WELL AS IN REVERSE. NO FURTHER TESTING WAS PERFORMED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) URYU US-LT30PB-05 OIL PULSE PNEUMATIC PISTOL GRIP NUTRUNNER/SCREWDRIVER SPECIFICATIONS: MANUFACTURER: URYU MODEL: US-LT30PB-05 DRIVE TYPE: 1/4" HEX MIN TORQUE: 8.8 IN LB MAX TORQUE: 44.0 IN LB MIN TORQUE: 1.0 NM MAX TORQUE: 5.0 NM CLUTCH TYPE: AUTO SHUT OFF TRIGGER TYPE: TRIGGER MAX FREE SPEED: 500 RPM SKU: Q10U027 1B-17-01(5) 4LBS - 10IN X 10IN X 6IN

MEMTRON 46974 WEBER SURETORK ELECTRIC SCREWDRIVER KEYPAD REPLACEMENT KEYPAD FOR USE WITH: WEBER SURETORK SCREWDRIVER CONTROLLERS WEIGHT: 0.60 LBS. CONDITION: NEW QUANTITY: 1 SKU: P06P006 2F-01-01(1) 0LBS - 17IN X 11IN X 6IN

CONVEYOR TECHNOLOGIES LIFT GATE PCB EDGE RAIL CONVEYOR

RUBBER COATED CONVEYOR ROLLER W/ FIXED 15MM AXEL 500MM X 60MM GOLD X 4MM TREAD - MANUFACTURER: UNBRANDED MODEL: DOES NOT APPLY CONDITION: USED. THIS CONVEYOR ROLLER IS IN GOOD COSMETIC CONDITION WITH ONLY MINOR SCUFFS AND SCRATCHES FROM REGULAR INDUSTRIAL USE AND HANDLING. COMES IN NON-ORIGINAL PACKAGING. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS ROLLER WAS REMOVED FROM DECOMMISSIONED EQUIPMENT AND HAS NOT BEEN TESTED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) UNBRANDED RUBBER COATED CONVEYOR ROLLER W/ AXLE 500MM X 60MM GOLD 4MM TREAD SPECIFICATIONS: MANUFACTURER: UNBRANDED MODEL: DOES NOT APPLY DESCRIPTION: RUBBER COATED CONVEYOR ROLLER W/ AXEL OVERALL TOTAL LENGTH: 500MM MAJOR DIAMETER (ROLLER DIAMETER): 60MM TREAD (RUBBER) THICKNESS: 4MM AXLE DIAMETER (MINOR DIAMETER): 15MM FIXED AXLE GOLD COLOR SKU: Y16H010 4B-04-03(1) 8LBS - 24IN X 6IN X 6IN

[CAREL UE090XM0U0] HUMISTEAM XPLUS ELECTRODE HUMIDIFIER 90KG/HR 460V 85A 3PHASE. THIS HUMIDIFIER IS IN FAIR COSMETIC CONDITION WITH MINOR BLEMISHES FROM PRIOR USE. THE STEAM DISTRIBUTORS HAVE LOTS OF RESIDUE, ESPECIALLY AT THE BASE WHERE THEY WERE SEALED TO DUCTWORK, AND AROUND THE HOLES WHERE THERE IS LIGHT RUST. THE CABINET HAS MINOR SCUFFS/SCRATCHES. THE CYLINDERS HAVE RESIDUES INSIDE. THIS HUMIDIFIER IS IN PARTIAL WORKING CONDITION. AT POWER ON IT GIVES ALARMS THAT BOTH THE CYLINDERS NEED SERVICE. IT HAS BEEN SITTING UP FOR SEVERAL YEARS AND MAY NEED OTHER MINOR MAINTENANCE. THE DISPLAY IS EASY TO READ AND BUTTONS RESPONDED TO USER INPUTS AS EXPECTED. INCLUDED: (1) CAREL UE090XM0U0 HUMIDIFIER (1) USER MANUAL (4) STEAM DISTRIBUTORS, 36" LONG SPECIFICATIONS: MANUFACTURER: CAREL MODEL: ELECTRODE HUMIDIFIER HUMISTEAM XPLUS SERIES PART NO.: UE090XM0U0 POWER REQUIREMENT: 460V 50/60HZ 84.7A 3PHASE 67.5KW PRODUCTION RATING: 90 KG/HR (198.5 LBS/HR) PROGRAMMABLE HUMIDITY CONTROLLER PHC COMES WITH 3' LONG STEAM DISTRIBUTORS TWO HUMIDIFIER CYLINDERS WATER INSTANT FLOW RATE: 14 L/M X-PLUS GRAPHICAL DIGITAL CONTROLLER UEXA3M0000 PROGRAMMABLE CONTROLLER DRAIN CONDENSATE MAY BE UP TO 100OC, UP TO 45 LITERS/HOUR 345LBS - 61IN X 40IN X 56IN