Industrial Electronic Manufacturing Process Equipment Parts Tools Day 3 of 3 day event

[4] NEW SWIVEL BASE 4"D X 1"W BLACK POLYURETHANE CASTER WHEELS W/0.35" SHAFT MANUFACTURER: UNBRANDED MODEL: DOES NOT APPLY INDUSTRIAL CASTER WHEELS WHEEL MATERIAL: BLACK POLYURETHANE BASE MATERIAL: STEEL WITH ZINC PLATING WHEEL DIAMETER: 4" WHEEL WIDTH: 1" MOUNTING: PIN SHAFT BASE SHAFT BASE DIAMETER: 0.35"

[YG] [04337] YG 5/8" M42 NON-CENTER CUTTING REGULAR LENGTH COBALT END MILL (5) - CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THESE END MILLS HAVE MINOR MARKINGS FROM NORMAL USE AND SHOW NO MAJOR DEFECTS THAT WOULD AFFECT FUNCTIONALITY. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THESE END MILLS WERE NOT TESTED DUE TO A LACK OF NECESSARY RESOURCES BUT WERE CAREFULLY INSPECTED FOR FLAWS. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (5) 5/8" M42 NON-CENTER CUTTING REGULAR LENGTH COBALT END MILL SPECIFICATIONS: MANUFACTURER: YG MODEL: 04337 DESCRIPTION: M42 NON-CENTER CUTTING REGULAR LENGTH COBALT END MILL CUTTING DIAMETER: 5/8" CUTTING DIRECTION: RIGHT HAND FINISH: UNCOATED HELIX ANGLE: 30-DEGREES MATERIAL M42 HSS-CO 8 MAX DEPTH OF CUT: 1-5/8" FLUTES: 4 OVERALL LENGTH: 3-3/4" SKU: U04U020 1A-01-01-01(1) 0LBS - 8IN X 8IN X 4IN

[TOSHIBA BA30F-UU-M20N-50X] LINEAR ACTUATOR BELT DRIVEN TOTAL TRAVEL: APPROXIMATELY 50CM DUAL LINEAR RAIL MOTION GUIDES APPROX. 72CM LONG 4X RECIRCULATING BALL BEARING BLOCKS BEARINGS: THK SHS15 MOTOR: MITSUBISHI ELECTRIC HC-KFS23 POWER: 200W INPUT: 118V 3PHASE 1.1A RATED SPEED: 3000RPM BALLSCREW DIAMETER: 20MM SCREW PITCH: 20MM STAGE OUTSIDE DIMENSIONS: 19CM X 12.8CM REMOVABLE ALUMINUM SCREW COVER PLASTIC BUMPERS ON EACH END OF TRAVEL

CENCORP BR1000 PCB DEPANEL ROUTER - BOARD DIMENSIONS UP TO 400 X 350 MM - PCB THICKNESS: 5 MM - MAX BOARD LENGTH: 400 MM - MAX BOARD WIDTH: 350 MM - NET WEIGHT: 2100 KG - OVERALL DIMENSIONS: 2225 X 1000 X 1950 MM INCLUDES VACUUM AND POWER SUPPLY.

PENSAR TUSCON INC. ROBOT CELL S/N: P98-674

[7] FAULTLESS 460S-5 5"X1 1/4" BLACK INDUSTRIAL REPLACEMENT CASTER WHEELS. WHEEL DIAMETER: 5". WHEEL/TREAD WIDTH: 1.25". WEIGHT CAPACITY: 350 LBS. MOUNT HEIGHT: 6.125". SWIVEL RADIUS: 3.9375". WHEEL MATERIAL: POLYPROPYLENE. BEARING TYPE: PLAIN. FASTENING SIZE: 2.875" X 3.625". BOLT HOLD SPACING: 1 3/4" X 2 15/16".

[20" GRAVITY CONVEYOR SPRING GATE SECTION] PASS THROUGH - MANUFACTURER: INTERLAKE MODEL: DOES NOT APPLY CONDITION: USED. COMES IN NON ORIGINAL PACKAGING. THE CONVEYOR GATE SECTION IS IN GOOD COSMETIC CONDITION WITH MINOR WEAR AND TEAR FROM PREVIOUS USE. HANDLES AND THE TWO SPRINGS ARE IN GOOD SHAPE. ROLLERS HAVE NO DENTS OR DINGS. COSMETICS MAY DIFFER SLIGHTLY FROM PICTURES. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: THE SPRINGS ON THE GATE WORKED WITH NO ISSUES. THE HANDLES OPENED AND CLOSED PROPERLY IN ORDER TO LIFT AND DESCEND THE GATE SMOOTHLY. NO FURTHER TESTING WAS PERFORMED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) INTERLAKE SPRING GATE CONVEYOR SECTION SPECIFICATIONS: MANUFACTURER: INTERLAKE MODEL: UNKNOWN LENGTH OF ROLLERS: 17 1/2" DIAMETER OF ROLLER: 34.96 MM; 1.3 IN WIDTH OF CONVEYOR: 20" 2 SPRINGS SKU: P42U003 5I-07-03(1) 265LBS - 58IN X 40IN X 45IN

[40] SOUTH WELD 53N58 #4 CERAMIC TIG GAS LENS CUP NOZZLE 1/4" SPECIFICATIONS: MANUFACTURER: SOUTH WELD MODEL: 53N58 DESCRIPTION: CERAMIC TIG WELDING GAS LENS CUP NOZZLE #4 1/4" SKU: U51H022 4B-01-02(1) 3LBS - 6IN X 6IN X 4IN

[NEW] QUALTECH DWTHX13812 1-3/8"-12 CARBON STEEL RETHREADING DIE RIGHT HAND SPECIFICATIONS: MANUFACTURER: QUALTECH MODEL: DWTHX13812 DESCRIPTION: CARBON STEEL RETHREADING DIE RIGHT HAND SIZE: 1-3/8"-12 HEX SIZE: 2-3/8" THICKNESS: 1.0" MATERIAL: CARBON STEEL CUTTING DIRECTION: RIGHT HAND

(4) PPI K.C. 4" SWIVEL LOCKING INDUSTRIAL STEEL ROLLING CASTER WHEELS - MANUFACTURER: PPI K.C. MODEL: UNKNOWN DESCRIPTION: LOCKING SWIVEL TYPE INDUSTRIAL STEEL 4" ROLLING CASTER WHEELS SWIVEL TYPE WHEEL DIAMETER: 4" WHEEL WIDTH: 1.25" TOTAL HEIGHT: 5" THE CASTERS ARE IN USED CONDITION WITH SCUFFS, SCRATCHES, AND SOME RESIDUE FROM PREVIOUS USE. THE WHEELS ROLL AND THE SWIVEL BASE WORKS AS INTENDED. NO FURTHER TESTING WAS PERFORMED AFTER REMOVAL. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN.

(1) EDWARDS PV40EKA C41403000 ELECTROMAGNETIC 110V VACUUM ISOLATION VALVE MANUFACTURER: EDWARDS MODEL: PV40EKA PART NUMBER: C41403000 DESCRIPTION: ELECTROMAGNETIC VACUUM ISOLATION VALVE VALVE ACTUATION TYPE: SINGLE ACTING, ELECTRICALLY OPENED, SPRING CLOSED PRESSURE RANGE VALVE OPEN: 1 X 10-9 TO 2000 MBAR 7.5 X 10-10 TO 1500 TORR (30 PSI) MAXIMUM PRESS DIFFERENTIAL OPENING/CLOSING: 1000 MBAR / 750 TORR VOLTAGE: 110V

[BOSTITCH D60ADC] COIL-FED PNEUMATIC CARTON CLOSER 70-100 PSI 1/4" NPT THREAD ACTUATION: PNEUMATIC SUPPLY PRESSURE: 70-100 PSI, 100 PSI MAX THREAD: 1/4" NPT LUBRICANT: BOSTITCH BC602 OR BC604 IS RECOMMENDED FRAME: LIGHT ALLOY FRAME MAGAZINE COMPATIBILITY: ACCOMODATES 1/2", 5/8", 3/4" SWC STAPLES SKU: V12B015 1C-03-04(2) 9LBS - 15IN X 12IN X 10IN

[BTU] FURNACE CONTROL UNIT FOR REFLOW OVEN. MANUFACTURER: BTU MODEL: 4170574 CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THE CONTROL UNIT IS IN USED CONDITION WITH SCUFFS, SCRATCHES, AND SOME MARKINGS FROM PREVIOUS USE. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: THE UNIT WAS REMOVED FROM A WORKING PARAGON 150 REFLOW OVEN. NO FURTHER TESTING WAS PERFORMED AFTER REMOVAL. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) BTU 4170574 REV-1 3615 FURNACE CONTROL UNIT SPECIFICATIONS: MANUFACTURER: BTU MODEL: 3615 PART #: 4170574-01 FURNACE CONTROL UNIT SERIES: PARAGON-150 ATMOSPHERE: NONEXPLOSIVE VOLTAGE: 480 VAC CURRENT RATING: 175 AMPS, 145 KVA PHASE: 3 FREQUENCY: 50/60 HZ MAX TEMPERATURE: 325 C SKU: V19B002 1E-17-03(2) 9LBS - 22IN X 15IN X 7IN

(LOT OF 4) DME COMPANY 7614 RETURN PINS 3/4" DIAMETER X 6-15/16" LENGTH - MANUFACTURER: DME MODEL: 7614 CONDITION: NEW. COMES IN FACTORY ORIGINAL PACKAGING. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (4) DME COMPANY 7614 RETURN SPRINGS SPECIFICATIONS: MANUFACTURER: DME MODEL: 7614 DESCRIPTION: RETURN PINS DIAMETER: 3/4" DIAMETER LENGTH: 6-15/16" TOTAL WEIGHT: 3.60 LBS. SKU: P42P006 1D-01-03(1) 6LBS - 14IN X 8IN X 4IN

[MKS INSTRUMENTS LPV-25 ANGLE VALVE WITH SMC NVZ110 SOLENOID VALVE] RIGHT ANGLE VALVE MANUFACTURER: MKS/HPS INSTRUMENTS MODEL: LPV-25 HEIGHT:203.2MM WIDTH:76.2MM LENGTH:101.6MM SOLENOID VALVE: MANUFACTURER:SMC MODEL: NVZ110 VOLTAGE: 24VDC PSI: 0-100

[CLECO] [8RSAPT-10B] PNEUMATIC PISTOL GRIP 1/4" AIR SCREWDRIVER/NUTRUNNER DRIVER - MANUFACTURER: CLECO MODEL: 8RSAPT-10B CONDITION: USED. COMES IN NON ORIGINAL PACKAGING. THE SCREWDRIVER HAS SOME SCUFFS, AND BLEMISHES FROM PREVIOUS USE. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: OUR TESTS INCLUDED PLUGGING IN THE SCREWDRIVER INTO AN AIR LINE HOSE. FORWARD AND REVERSE WORKED GREAT WITH NO ISSUES. NO FURTHER TESTING WAS PERFORMED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) CLECO 8RSAPT-10B PISTOL GRIP AIR PNEUMATIC SCREWDRIVER/NUTRUNNER SPECIFICATIONS: MANUFACTURER: CLECO MODEL: 8RSAPT-10B 1/4" HEX QUICK CHANGE CHUCK PISTOL GRIP STYLE SLIDING KNOB REVERSE PUSH TO START REVERSIBLE SKU: Q12U036 4C-01-02(1) 4LBS - 10IN X 10IN X 6IN

[AMERICAN FAN COMPANY] SC-600 6" BLOWER WITH 3/4HP BALDOR VM3112 3 PHASE MOTOR. MANUFACTURER: AMERICAN FAN COMPANY MODEL: SC-600. CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THIS BLOWER IS IN FAIR COSMETIC CONDITION. THE END OF THE MOTOR HAS SOME LIGHT CORROSION, AND THE MOTOR SHAFT HAS SOME SURFACE RUST; NEITHER OF THESE AFFECT OPERATION. THERE ARE ALSO SCUFFS/SCRATCHES AND MINOR RESIDUES FROM PRIOR USE. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: WE CONNECTED THIS FOR 208V AND IT RAN QUIETLY, WITH A STRONG JET OF AIR FROM THE OUTPUT FLANGE. NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) AFC SC-600 BLOWER SPECIFICATIONS: MANUFACTURER: AMERICAN FAN COMPANY MODEL: SC-600 SC-SERIES VOLUME BLOWER 3/4 HORSEPOWER 3-PHASE AC MOTOR NOMINAL SIZE: 6" PERFORMANCE: 600 CFM @ 0" TO 500CFM AT 1" H20 (MAXIMUM 1.2" H2O @ NO FLOW) CAST ALUMINUM VOLUTE FORWARD-CURVED STEEL IMPELLER WHEEL FLANGE MOUNTED ROUND SLIP FIT INLET DIRECT DRIVE MOTOR: BALDOR VM-3112, 34F12-883 POWER REQUIREMENT: 208-230/460V 60HZ 3.2/1.5A 3PHASE FRAME: 56C SPEED: 1725 RPM RATED FOR CONTINUOUS OPERATION AT 40OC AMBIENT SKU: Y19D003 5C-15-03(3) 30LBS - 25IN X 19IN X 16IN

[WRIGHT TOOL] 5836 #5 SPLINE 6-POINT STANDARD IMPACT SOCKET 1-1/8" SOCKET DIAMETER: 1-13/16" DRIVE DIAMETER: 2-3/8" LENGTH: 3-1/16" WEIGHT: 1.80LBS. THIS SOCKET HAS SOME DINGS, SCUFFS, AND SCRATCHES, ALONG WITH SOME SPOTS OF RUST AND OTHER MARKINGS EVIDENT FROM NORMAL USE. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). THIS SOCKET WAS REMOVED FROM AN ACTIVE WORKING ENVIRONMENT AND WAS NOT TESTED SUBSEQUENT TO ITS REMOVAL. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. SKU: U47U020 2O-03-02(4)

[TIG STAR T54N16] TIG TORCH NOZZLE #6 9.5MM 3/8" GAS LENS CUP 17/18/26. THESE NOZZLES ARE IN A NEW AND UNUSED COSMETIC CONDITION AND COME INDIVIDUALLY PACKAGED IN THE ORIGINAL WELDTEC BOX THAT DOES SHOW SOME SIGNS OF SHELF WEAR AND OCCASIONALLY WRITING ON THE OUTSIDE OF THE BOX. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (30) TIG STAR T54N16 #6 9.5MM 3/8" TIG TORCH NOZZLE <3 PACKS OF 10> SPECIFICATIONS: MANUFACTURER: TIG STAR MODEL: T54N16 DESCRIPTION: TIG TORCH NOZZLE #6 9.5MM 3/8" GAS LENS CUP 17/18/26 SKU: U51H004 1B-21-02(1) 2LBS - 7IN X 7IN X 7IN

[34] TECHNIWELD TIG STAR 57N75 #6 CERAMIC CUP NOZZLE 3/8" S/N: V04H017 (1) - MANUFACTURER: TECHNIWELD MODEL: 57N75 CONDITION: NEW OTHER. THESE NOZZLES ARE IN A NEW AND UNUSED COSMETIC CONDITION AND COME INDIVIDUALLY PACKAGED IN THE ORIGINAL BOXES THAT DO SHOW SOME SIGNS OF SHELF WEAR AND OCCASIONALLY WRITING ON THE OUTSIDE OF THE BOX. TWO OF THESE BOXES ARE BRANDED AS TIG STAR AND TWO OF THE BOXES ARE TECHNIWELD, SAME MODEL NUMBER. THESE BOXES ORIGINALLY CONTAINED 10 CUPS BUT NOW THREE OF THE BOXES ARE MISSING SOME CUPS. THE TOTAL COUNT OF CUPS IS 34. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (34) TIG STAR / TECHNIWELDSEE U51H019 57N75 #6 CERAMIC GAS LENS NOZZLE 3/8" SPECIFICATIONS: MANUFACTURER: TIG STAR / TECHNIWELD MODEL: 57N75 DESCRIPTION: TIG WELDING CERAMIC LARGE GAS LENS CUP NOZZLE #6 3/8" SKU: V04H017 1E-08-02(1) 5LBS - 8IN X 8IN X 7IN

[COMMERCIAL FOOD-GRADE STAINLESS UPRIGHT TUMBLING CHIP CONVEYOR PLASTIC-CHAIN] CONVEYOR: MANUFACTURER: UNKNOWN MODEL: UNKNOWN FOOD GRADE CONSTRUCTION: STAINLESS STEEL PLASTIC CHAIN ADJUSTABLE TILT 3 ROWS: 10" WIDTH 11" WIDTH BELTS 9.5" METAL PLATES REDUCER: MANUFACTURER: BOSTON GEAR STAINLESS BOST - KLEEN WASH DOWN INPUT HP: 1.33 OUTPUT TORQUE: 1200 LB IN RATIO: 30 ACCESS POINT: MODEL: HOWABN1 MANUFACTURER: HAWKING TECHNOLOGY HI-GAIN OUTDOOR WIRELESS 3000N ACCESSPOINT/BRIDGE/REPEATER DISCONNECT SWITCH: MANUFACTURER: HUBBELL CAT. #: HBLDS3 CIRCUIT-LOCK 30A, 600VAC MAX. SKU: V35L003 6-BILR2(1) 1587LBS - 77IN X 71IN X 81IN. SCUFFS, SCRATCHES, AND DIRT RESIDUE FROM NORMAL USE. LARGER ELECTRICAL ENCLOSURE INTERIOR IS BASICALLY EMPTY. SMALLER ELECTRICAL ENCLOSURE HAS A TRANSFORMER IN IT. SHAFT THAT ROTATES THE 3 BELT SECTIONS ONLY HAS A REDUCER ATTACHED TO IT, NO MOTOR. TO CHANGE THE TILT, ONE SIDE HAS AN ADJUSTMENT THREADED BOLT WHILE THE OTHER SIDE IS "HINGED". CASTERS FOR MOBILITY BUT TWO OF THEM HAVE THEIR OUTER CASING BROKEN OFF.

(1) ALLEN-BRADLEY BULLETIN 1330 ADJUSTABLE FREQUENCY MOTOR DRIVE 1.6 KVA OUTPUT SPECIFICATIONS: MANUFACTURER: ALLEN BRADLEY MODEL: BULLETIN 1330 PART NUMBER: 1330-AOA-TW4 ADJUSTABLE FREQUENCY MOTOR DRIVE MADE IN USA INPUT: VOLTAGE: 230 VAC CURRENT RATING: 2.5 AMPS FREQUENCY: 60 HZ PHASE: 3 KVA RATING: 1 OUTPUT: VOLTAGE: 0-230 VAC CURRENT: 4 AMPS FREQUENCY: 0-60 HZ PHASE: 3 KVA RATING: 1.6

[ATI INDUSTRIAL AUTOMATION] QC011T ROBOT TOOL CHANGER PLATE WITH E20-10 20-PIN MOD. MANUFACTURER: ATI INDUSTRIAL AUTOMATION, MODEL: QC011T. ROBOTIC TOOL CHANGER. LIGHTWEIGHT, SMALL SIZE WITH HIGH STRENGTH LOCKING MECHANISM. NO-TOUCH LOCKING TECHNOLOGY ALLOWS UP TO 1.5MM PLATE SEPARATION WHEN LOCKING. SUGGESTED PAYLOAD LIMIT: 16KG. LOCKING FORCE @ 5.5 BAR: 1100 N. POSITIONAL REPEATABILITY: 0.0102MM. (6) PNEUMATIC PASS-THROUGH PORTS. REQUIRES A MASTER PLATE (NOT INCLUDED) FOR OPERATION. ELECTRICAL MODULE: E20-010 TOOL SIDE 20 PINS 3 AMP/50 VAC SOLDER CONNECTION. 2LBS - 6IN X 6IN X 4IN

2007 SWEP B25HX16/1P-SC-S INDUSTRIAL HEAT EXCHANGER MAX-WORKING-PRESSURE: 31 BAR INDUSTRIAL HEAT EXCHANGER CONSTRUCTION: 316/316L STAINLESS STEEL PLATES, COPPER BRAZING LENGTH: 20.75" WIDTH: 4.5" HEIGHT: 3.5" MAX WORKING TEMPERATURE: 155(225) C MAX WORKING PRESSURE: 31(27) BAR TEST PRESSURE: 50 BAR VOLUME: 0.798L PRIMARY, 0.912L SECONDARY YEAR OF MANUFACTURER: 2007

[NEW OTHER] JOGLER LS 10 285 PSIG ARMORED LEVEL GAUGE SINGLE GLASS TUBE 36" LONG - MANUFACTURER: JOGLER MODEL: LS 10 CONDITION: NEW OTHER. COMES IN ORIGINAL PACKAGING. THE ITEM IS NEW/ UNUSED. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) JOGLER LS 10 ARMORED LEVEL GAUGE 36" LON SPECIFICATIONS: MANUFACTURER: JOGLER MODEL: LS 10 ARMORED GLASS LEVEL GAUGE FLOW METER PRESSURE RATING: 285 PSIG UNOBSTRUCTED VISIBILITY PATENTED ONE-PIECE SUPERSEAL INSERTS ARE SELF-SEALING MAINTENANCE FREE BOROSILICATE SIGHT TUBING PTFE TEFLON SUPERSEAL INSERTS EPOXY-COATED CARBON STEEL SHIELD AND FLANGES ANSI CLASS 150-LB FLANGES APPROVED BY THE FACTORY MUTUAL SYSTEM (150O F MAX) SKU: R43B033 5A-02-01(1) 18LBS - 48IN X 8IN X 8IN

(1) WESTERN INNOVATOR LCHP-7-2 PORTABLE BULK GAS MANIFOLD 350PSIG 0-120F TEMP. RANGE MANUFACTURER: WESTERN INNOVATOR MODEL: LCHP-7-2 PORTABLE BULK GAS MANIFOLD MAX PRESSURE 350 PSIG TEMPERATURE RANGE: 0-120F AUTOMATIC ANALOG SYSTEM MANIFOLD OUTLET: 1/2" NPT MALE RELIEF VALVE OUTLET: 1/4" NPT MALE NITROGEN CGA-580 2-CYLINDERS

[CONVEYOR TECHNOLOGIES] LG-48I-1-L-0640 LIFT GATE OPEN-CENTER BOARD-EDGE - MANUFACTURER: CONVEYOR TECHNOLOGIES CTI MODEL: LG-48I-1-L-0640 CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THIS GATE IS IN FAIR COSMETIC CONDITION WITH LOTS OF SCUFFS/SCRATCHES TO THE BARE METAL, AS WELL AS RESIDUES FROM OLD ADHESIVE LABELS. THERE IS A CYLINDER INSIDE THAT LOOKS LIKE IT SHOULD BE A LIFTING CYLINDER TO RAISE THE GATE BUT THIS IS DISCONNECTED FROM ANY AIR SOURCE; WE ARE NOT SURE WHY. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: THIS UNIT IS IN GOOD WORKING CONDITION. WHEN A BOARD IS PRESENTED TO THE INPUT SIDE, THE CONVEYOR RUNS. WHEN IT CROSSES THE OUTPUT SENSOR, THE CONVEYOR STOPS. WHEN EITHER PAUSE/LIFT BUTTONS ARE PRESSED, THE CONVEYOR STOPS AND THE PNEUMATIC CLAMP RELEASES SO A USER CAN LIFT THE GATE OUT OF THE WAY. WHEN THE GATE IS LOWERED AGAIN, THE PNEUMATICS CLAMP IT IN PLACE. NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) CTI LG-48I-1-L-0640 BOARD CONVEYOR LIFT GATE SPECIFICATIONS: MANUFACTURER: CONVEYOR TECHNOLOGIES MODEL: CTI LG-48I-1-L-0640 CIRCUIT BOARD CONVEYOR AISLE GATE 28" AISLE OPENING GATE IS OPENED MANUALLY BY LIFTING GATE FROM EITHER SIDE EMERGENCY STOP OPERATORS ON BOTH SIDES CONVEYOR WIDTH ADJUSTMENT RANGE: 18" TO 2" 2 CONVEYOR DRIVE SECTIONS PNEUMATIC LOCK DURING PCB TRANSFER PLC CONTROLS WITH SMEMA CONNECTIONS POWER: 120V 60HZ 1.6A

[COLUMBUS MCKINNON CM 1.5-TON MANUAL RATCHET LEVER CHAIN HOIST] 10'-LENGTH-CHAIN SPECIFICATIONS: MANUFACTURER: COLUMBUS MCKINNON CM MODEL: UNKNOWN CHAIN LENGTH: 10' CAPACITY: 1.5 TON OPERATION: MANUAL HAND TYPE: CHAIN HOIST SKU: W51L007 5C-02-02(1) 38LBS - 36IN X 25IN X 10IN

[800] NEW POWERS 55330 .730" C5 TRAK-IT STRAIGHT PINS NO FUEL CELL MANUFACTURER: POWERS FASTENERS MODEL: 55330 DESCRIPTION: C5 TRAK-IT STRAIGHT PINS APPLICATION: 1/4" PLYWOOD TO STEEL OR HARD CONCRETE PINS FOR C5 TRAK-IT GUN PIN LENGTH: 0.730" SHANK DIAMETER: 0.120" NO FUEL CELL

(1) OZAT 9538 2-3/8-INCH 6-POINT #5 SPLINE DRIVE REGULAR LENGTH IMPACT SOCKET 6.30LB MANUFACTURER: OZAT MODEL: 9538 DESCRIPTION: 6-POINT #5 SPLINE DRIVE IMPACT SOCKET SIZE: 2-3/8" LENGTH: 98MM 3.85" SOCKET DIAMETER: 88MM 3.46" DRIVE DIAMETER: 86MM 3.38" WEIGHT: 6.30LB SKU: U46U045 2O-06-03(4) 9LBS - 6IN X 6IN X 4IN

[WOOD'S GD55S] INDUSTRIAL 101 PINTS DEHUMIDIFIER MANUAL HUMIDISTAT REAR PANEL OPEN - MANUFACTURER: WOOD'S MODEL: GD55S CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THIS DEHUMIDIFIER IS IN FAIR COSMETIC CONDITION WITH DUST AND RESIDUES FROM PRIOR USE. THE REAR PANEL, WHICH INCLUDES THE AIR FILTER, IS MISSING. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS DEHUMIDIFIER IS IN GOOD WORKING CONDITION. WE SWITCHED ON AND LET IT RUN UNTIL THE DRAIN HOSE WAS DRIPPING WITH WATER. THE CONDENSER SHUT OFF EVERY ONCE IN A WHILE DURING OPERATION. NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) WOOD'S GD55S DEHUMIDIFIER SPECIFICATIONS: MANUFACTURER: WOOD'S MODEL: GD55S DEHUMIDIFIER CAPACITY RATINGS: AT SATURATION: 101 PINTS 80OF 60% RH (AHAM): 52 PINTS 2-SPEED FAN HUMIDISTAT, MANUALLY ADJUSTABLE PAINTED STEEL CABINET CASTERS FOR EASY RELOCATION FOLD-DOWN HANDLE CONFIGURED FOR CONTINUOUS DRAIN-OFF (NO INTERNAL RESERVOIR) R410A REFRIGERANT POWER: 115V 60HZ 5A AIR FLOW: 325 CFM DIMENSIONS: 16"W X 17"D X 21"H (INCLUDING HANDLE WIDTH) SKU: W13D004 48LBS - 25IN X 25IN X 20IN

[POLY HI SOLIDUR GNFA0630] SPUR GEAR 6 PITCH 5" PITCH DIAMETER 30 TOOTH SPUR GEAR 1-1/2" FACE WIDTH 1-3/4" MAX BORE 3" HUB DIAMETER OIL FILLED NYLON MACHINED OIL FILLED NYLON 6DP 1-1/2" FACE

2007 CONVEYOR TECHNOLOGIES TT-30I-4S-0640 MULTI-LINE PCB TURNTABLE NO TOUCHSCREEN - PARTS. MANUFACTURER: CONVEYOR TECHNOLOGIES CTI MODEL: TT-30I-4S-0640 CONDITION: FOR PARTS OR NOT WORKING. THIS UNIT IS IN FAIR COSMETIC CONDITION. THERE SCUFFS/SCRATCHES AND ADHESIVE RESIDUES FROM PRIOR USE. INCLUDING ALL THE WAY TO BARE METAL. SOME OF THE PLASTIC WINDOWS ARE CRACKED. THE TOUCHSCREEN HMI WAS REMOVED. A FOOT IS MISSING. NOTES: WITHOUT AN HMI WE COULD NOT TEST THIS UNIT. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) CTI TT-30I-4S-0640 PCB TURNTABLE SPECIFICATIONS: MANUFACTURER: CONVEYOR TECHNOLOGIES INC. (CTI) MODEL: TT-30I-4S-0640 MULTI-LINE TURNTABLE CIRCUIT BOARD TURN TABLE CAPABLE OF RECEIVING BOARDS AT RIGHT/LEFT/REAR, THEN SENDING TO EITHER OF THE OTHER EXITS FOR RIGHT-ANGLE OR STRAIGHT-THROUGH PROCESS LINES BOARD SIZE: 2" X 4" TO 16" X 18" CONVEYOR HEIGHT: 37.5" +/-2" CYCLE TIME: 12 SECONDS OMRON CPM2A PLC ROTATION DRIVEN BY CAMCO 80RDM4H20-330 ROTARY INDEXER POWER: 120V 60HZ 4.7A MANUFACTURED: DECEMBER 2007 INCOMPLETE, NOT WORKING!

[ALBION] STAINLESS STEEL SWIVEL CASTER WHEELS TWO STRAIGHT TWO LOCKING (4) - MANUFACTURER: ALBION MODEL: DOES NOT APPLY CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THE CASTERS ARE IN USED CONDITION WITH SCUFFS AND SCRATCHES FROM HEAVY REGULAR USE. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THE CASTERS WERE REMOVED FROM A DECOMMISSIONED MACHINE. THE CAST WHEELS ROLL WITH NO OBSTRUCTION. NO FURTHER TESTING WAS PERFORMED AFTER REMOVAL. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (2) ALBION STAINLESS STEEL SWIVEL CASTER LOCKING WHEELS (2) ALBION STAINLESS STEEL SWIVEL CASTER STRAIGHT WHEELS SPECIFICATIONS: MANUFACTURER: ALBION MODEL: DOES NOT APPLY DESCRIPTION: ALBION STAINLESS STEEL SWIVEL CASTER WHEELS TWO STRAIGHT TWO LOCKING SWIVEL TYPE TWO LOCKING CASTERS WHEEL DIAMETER: 3" WHEEL WIDTH: 1.25" BASE DIMENSIONS: 2.50" X 3.75" TOTAL HEIGHT 4" BOLT HOLE WIDTH: 1.75" X 3"

[UNIVERSAL INSTRUMENTS] CT-0891 SURFACE MOUNT COMPONENT FEEDERS 8MM USED WITH 4796 SERIES HIGH SPEED PLACEMENT MACHINE LARGE TYPE FEEDERS CT-0891 -0898 (77) W/ ROLL-AROUND STORAGE RACK. THE CART IS A BIT ROUGH, WITH LOTS OF SCRATCHED PAINT. THE FEEDERS ALL LOOK COMPLETE, EXCEPT 7 HAVE THE SPRING-LOADED ARM MISSING FROM THE BIG REEL SECTION. MOST HAVE AT LEAST ONE HAND-WRITTEN OR TAPED-ON MARKING. THE SIDES OF THE FEEDERS HAVE TYPICAL SCUFFS/SCRATCHES FROM PRIOR USE. INCLUDED: (68) CT-0891 FEEDERS (9) CT-0898 FEEDERS (1) STORAGE CART. CART HAS 79 FEEDER POSITIONS PLUS A DIY-LOOKING COUPLE-DOZEN MORE ON BOTTOM RACK. 530LBS - 68IN X 44IN X 54IN

[INGERSOLL-RAND W3A1] INGERSOLL-RAND W3A1 HEAVY DUTY PNEUMATIC CHIPPING HAMMER 3/8"NPT 1725BPM. BORE: 1.13" STROKE LENGTH: 3" BPM: 1725 AIR CONSUMPTION: 29CFM RUBBER BUFFERED AIR INLET: 3/8" MINIMUM HOSE SIZE: 1/2" LENGTH: 18.25". CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THE CHIPPING HAMMER IS IN GOOD, USED CONDITION WITH SOME SCUFFS AND FINISH CHIPPING FROM PREVIOUS USE. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THE HAMMER WAS REMOVED FROM A DECOMMISSIONED ENVIRONMENT. NO FURTHER TESTING WAS PERFORMED AFTER REMOVAL. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) INGERSOLL-RAND W3A1 HEAVY DUTY PNEUMATIC CHIPPING HAMMER 3/8"NPT 1725BPM SPECIFICATIONS: MANUFACTURER: INGERSOLL RAND MODEL: W3A1 HEAVY DUTY INDUSTRIAL CHIPPING HAMMER BORE: 1.13" STROKE LENGTH: 3" BPM: 1725 AIR CONSUMPTION: 29CFM RUBBER BUFFERED AIR INLET: 3/8" MINIMUM HOSE SIZE: 1/2" LENGTH: 18.25". SKU: X28B020 1D-01-01(1) 21LBS - 25IN X 12IN X 8IN

[BEST WELDS] 4.5" X 5.25" HARDENED GLASS FILTER PLATE (9) - MANUFACTURER: BEST WELDS MODEL: 932-107-11 DESCRIPTION: HARDENED GLASS LENS WELDING FILTER PLATE 4.5 X 5.25 SHADE 11 SKU: U49H013 1E-09-01(1) 5LBS - 10IN X 10IN X 6IN

[USED] MITUTOYO 30CM STAINLESS HARDENED UPRIGHT HEIGHT GAUGE ~20.75" TOTAL HEIGHT. ADJUSTABLE HEIGHT GAUGE 30CM. CONSTRUCTION: STEEL, STAINLESS HARDENED. UNIT TOTAL HEIGHT: ~20.75". BASE DIMENSIONS: 5.75"L X 3.75"W X 1.75"H. INCREMENTS: 1MM. MADE IN JAPAN.

[2] DE STA CO 604 STRAIGHT LINE ACTION CLAMP W/ ADJUSTABLE PNEUMATIC HOLDING BASE. MANUFACTURER: DESTACO MODEL: 604 CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THE STRAIGHT CLAMP AND BASE ARE IN GOOD CONDITION. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: THE STRAIGHT LINE ACTION CLAMP CAN BE MOVED UP AND DOWN BY PROPERLY USING THE CLAMP HANDLE. THE CLAMP IS IN GOOD WORKING CONDITION. NO FURTHER TESTING WAS PERFORMED. SPECIFIC JAM NUTS NOT INCLUDED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (2) DE STA CO 604 STRAIGHT LINE ACTION CLAMP W/ ADJUSTABLE PNEUMATIC HOLDING BASE SPECIFICATIONS: MANUFACTURER: DE STA CO MODEL: 604 STRAIGHT LINE ACTION CLAMP W/ BASE FULLY RETRACTABLE LOCATORS ERGONOMIC HANDLE GRIP 4 SUCTION CUP FEET BASE 1: 1" (LXW) BASE 2: 0.5" (LXW) SKU: M35N020 1B-13-02(1) 6LBS - 14IN X 11IN X 5IN

(2) QINDE WLL 6 1/2T 7/8" 6.5 TON CAPACITY ANCHOR SHACKLES W/PIN. SPECIFICATIONS: MANUFACTURER: QINDE MODEL: WLL 6 1/2T ANCHOR SHACKLE AND PIN ASSEMBLY THICKNESS: 7/8" HOLDING CAPACITY: 6.5 TONS LENGTH: 6" WIDTH: 4.25" HEIGHT: 2.25" PIN THREAD: 1" MADE IN CHINA.

TENTE GREY INDUSTRIAL 2-LOCKING SWIVEL TYPE 4" CASTER WHEELS (4) - MANUFACTURER: TENTE MODEL: DOES NOT APPLY CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THE CASTERS ARE IN USED CONDITION WITH SCUFFS, SCRATCHES, AND SOME RESIDUE FROM PREVIOUS USE. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: THE CASTERS WERE REMOVED FROM DECOMMISSIONED MACHINES. THE WHEELS ROLL AND THE SWIVEL BASE WORKS AS INTENDED. NO FURTHER TESTING WAS PERFORMED AFTER REMOVAL. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (4) TENTE GREY INDUSTRIAL 2-LOCKING SWIVEL TYPE 4" CASTER WHEELS SPECIFICATIONS: MANUFACTURER: HAMMER MODEL: DOES NOT APPLY DESCRIPTION: CASTER WHEELS SWIVEL TYPE WHEEL DIAMETER: 4" WHEEL WIDTH: 1.25" BASE DIMENSIONS: 3" X 2.75" TOTAL HEIGHT: 5.50" BOLT HOLE WIDTH: 2" X 2.50"

MATE STEEL PRESS BRAKE TOOLING DIES .062X.625+.012 TO .312X1.0+.012 (19) - MANUFACTURER: MATE MODEL: DOES NOT APPLY CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THE TOOLING DIES ARE IN GOOD, USED CONDITION WITH SOME SCUFFS AND OXIDATION RESIDUE FROM PREVIOUS USE. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THE DIES WERE REMOVED FROM DECOMMISSIONED MACHINES. NO FURTHER TESTING WAS PERFORMED AFTER REMOVAL. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (19) MATE STEEL PRESS BRAKE TOOLING DIES .062X.625+.012 TO .312X1.0+.012 SPECIFICATIONS: MANUFACTURER: MATE MODEL: DOES NOT APPLY PRESS BRAKE TOOLING DIES MATERIAL: STAINLESS STEEL SLUG FREE DIAMETER: 1.567" SIZES: (1) .062 X .625 + .012 (1) .137 X .637 (1) .125 X .500 + .018 (1) .265 X .406 + .018 (1) .312 X .750 + .012 (1) .171 X .500 + .036 (1) .218 X 1.00 + .018 (1) .281 X .500 + .012 (1) .171 X .281 + .010 (1) .218 X .406 + .010 (1) .375 X .500 + .032 (1) .375 X .750 + .024 (1) .312 X .500 + .010 (1) .328 X .828 + .024 (1) .375 X .625 + .012 (1) .218 X .750 + .018 (1) .281 X .375 + .012 (1) .312 X .625 + .012 (1) .312 X 1.00 + .012 SKU: T02B003 1D-10-02(1) 6LBS - 8IN X 8IN X 7IN

[INDUSTRIAL GRANITE MACHINE BLOCK/SURFACE 55.5"L X 42" X 8" FLAT SURFACE PLATE] - MANUFACTURER: UNBRANDED MODEL: DOES NOT APPLY CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THE MACHINE SURFACE BLOCK IS IN GOOD, USED CONDITION WITH NO STRUCTURAL CRACKS. THERE ARE SOME MINOR SCUFFS AND SCRATCHES FROM PREVIOUS USE AND INSTALLATION. WE ARE NOT SURE WHAT GRADE THE SURFACE IS. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THE BLOCK WAS REMOVED FROM A DECOMMISSIONED MACHINE. NO FURTHER TESTING WAS PERFORMED AFTER REMOVAL. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) INDUSTRIAL GRANITE MACHING BLOCK/SURFACE 55.5"L X 42" X 8" FLAT SURFACE SPECIFICATIONS: MANUFACTURER: UNBRANDED MODEL: DOES NOT APPLY INDUSTRIAL MACHINE SURFACE PLATE MATERIAL: GRANITE LENGTH: 55.5" WIDTH: 42" HEIGHT: 8" INNER HOLE DIAMETER: 15.5" THREADS: 3/16" 3/8" 8/32" 0.75" SKU: X31G002 6-BILR1(1) 1940LBS - 64IN X 51IN X 16IN

[USED] STANDARD PNEUMATIC 6021 ELECTRIC 120V WIRE-WRAP GUN TOOL 18-32 AWG LEXAN. COMES IN NON ORIGINAL PACKAGING. THE WIRE WRAP TOOL IS IN GOOD COSMETIC CONDITION WITH LIGHT WEAR FROM PREVIOUS USE. THE CORD IS IN GOOD CONDITION WITH NO FRAYING. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: TESTING INCLUDED PLUGGING IN THE CORD TO A STANDARD OUTLET. THE TRIGGER WAS PULLED AND SEEMED TO WORK GREAT WITH NO ISSUES. NO FURTHER TESTING WAS PERFORMED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) STANDARD PNEUMATIC 6021 WIRE WRAP GUN. SPECIFICATIONS: MANUFACTURER: STANDARD PNEUMATIC MODEL: 6021 ERGONOMIC AND WELL-BALANCED WORKS WITH 18-32 AWG WIRE LIGHT PULL TRIGGER GEARED DRIVE POSITIVE INDEXING MECHANISM DURABLE HIGH SPEED ELECTRIC MOTOR STANDARD 20 FT POWER CORD 120 VOLTS 4000 RPM. SKU: Q10U023 1D-09-02(1) 4LBS - 10IN X 10IN X 8IN

[4] INDUSTRIAL SWIVEL TYPE HEAVY-DUTY STEEL ROLLING 3" CASTER WHEELS SWIVEL TYPE WHEEL DIAMETER: 3" WHEEL WIDTH: 1.75" TOTAL HEIGHT: 4" BASE DIMENSIONS: 4.25" X 3.25" BOLT HOLE WIDTH: 2.50" X 3.75". THE CASTERS ARE IN USED CONDITION WITH SCUFFS, SCRATCHES, AND RESIDUE FROM PREVIOUS USE. THE WHEELS ROLL AND THE SWIVEL BASE WORKS AS INTENDED.

WINHOLT INDUSTRIAL TWO ROLLING TWO LOCKING 5" CASTER WHEELS (4) - WINHOLT INDUSTRIAL ROLLING 5" CASTER WHEELS, WINHOLT INDUSTRIAL LOCKING 5" CASTER WHEELS. SWIVEL TYPE TWO LOCKING. WHEEL DIAMETER: 5". WHEEL WIDTH: 1.25". TOTAL HEIGHT 8.25". STEM WIDTH: 1".

THK 28" 711.2MM LONG "L" DESIGN STAINLESS STEEL LINEAR GUIDE RAILS (5) LINEAR GUIDE RAILS DESIGN: "L" SHAPED ON THE UNDERSIDE COLOR: SILVER LENGTH: 28", 711.2 MM TOP WIDTH: 0.61" UNDERSIDE WIDTH: 0.76" MOUNTING HOLE DIAMETERS: 0.236", 0.37" CONSTRUCTION: STAINLESS STEEL WEIGHT: 2.80 LBS EACH

[JOHN CRANE LMA-52575-001] 30 PSI 1.5 GPM 50/50 EG/W INDUSTRIAL WET SEAL SYSTEM. SPECIFICATIONS: MANUFACTURER: JOHN CRANE MODEL: LMA-52575-001 DESCRIPTION: PRESSURE: 30 PSI FLOW RATE: 1.5 GPM FLUID: 50/50 EG/W DIMENSIONS: TOP OPEN CONNECTION: 1" UNITED ELECTRIC QJ120-15190 PRESSURE SWITCH: 5 TO 30 PSI 0.3 TO 2.1 BAR 15A 480VAC WELLMARK 790SF-1A LIQUID LEVEL SWITCH: 1500 PSI / 10.3 MPA 5A @ 250VA LONE STAR V-530SCV VALVE: 316SS 10000 PSI @ 200F 8000 PSI @ 400F MAX. SKU: Y20G009 1E-13-06(2) 265LBS - 48IN X 40IN X 40IN

[175-F 79-C] MARKAL 86481 THERMOMELT HEAT STICK TEMP 175-F 79-C (12) - MANUFACTURER: MARKAL MODEL: 86481 CONDITION: NEW OTHER. THESE HEAT STICKS ARE IN A NEW AND UNUSED COSMETIC CONDITION AND COME IN THE ORIGINAL MARKAL BOX THAT CONTAINS 12 STICKS. THE BOX SHOWS SOME MINOR WEAR FROM STORAGE. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (12) MARKAL 86481 THERMOMELT HEAT STICK TEMP 175-F 79-C SPECIFICATIONS: MANUFACTURER: MARKAL MODEL: 86481 DESCRIPTION: THERMOMELT HEAT STICK TEMP 175-F 79-C THE BIG STICK! SKU: V03H031 2F-03-02(2) 2LBS - 8IN X 8IN X 4IN

[RITTAL TOP THERM SK 3384.510] ENCLOSURE AIR CONDITIONER COOLING UNIT AC 115V B. THIS COOLER IS IN FAIR COSMETIC CONDITION. THERE ARE SCUFFS/STAINS/SCRATCHES FROM PRIOR USE ALL OVER BUT MOSTLY ON TOP. THE UNIT YOU RECEIVE MAY HAVE MINOR CORROSION. THIS COOLING UNIT IS FITTED TO A ROLL-AROUND CART/BASE/DUCT ADAPTER, WHICH THE PRIOR OWNERS USED TO HAVE HOOKED UP TO THEIR EQUIPMENT WITH HOSES. THE UNIT YOU RECEIVE MAY HAVE A LITTLE MORE DUST THAN THIS ONE, AND THE POWER CORD MAY BE LONGER THAN THE ONE SHOWN. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: THIS UNIT IS IN GOOD WORKING CONDITION. WHEN WIRED TO OUR 115V MAINS POWER AND WITH THE TEMPERATURE SETPOINT SET APPROPRIATELY, THIS UNIT BLOWS A STRONG JET OF COOL AIR FROM THE OUTLET ON THE BASE (THE LEFT HOLE) AND DRAWS AIR INTO THE INLET (THE RIGHT HOLE). THE COLD AIR OUTPUT WAS 50OF OR COLDER ON ALL THE UNITS WE HAVE IN-HOUSE. THERE IS A DISTINCT WHISTLING NOISE THAT COMES FROM THE COOLING AIR - THIS IS FROM THE ADAPTER BASE AND WOULD GO AWAY WITH DUCTS INSTALLED ON YOUR EQUIPMENT. IT ALSO WENT AWAY WHEN WE TEMPORARILY LIFTED THE COOLING UNIT OFF THE BASE. THE WHEELS ROLL EASILY. OPERATION IS RELATIVELY QUIET (YOU CAN TALK OVER IT WITHOUT RAISING YOUR VOICE, EVEN VERY NEAR THE UNIT). NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) RITTAL SK 3384.510 COOLING UNIT (1) DUCT ADAPTER BASE/CART SPECIFICATIONS: MANUFACTURER: RITTAL TOPTHERM MODEL: SK 3384.510 (SK3384510) ENCLOSURE COOLING UNIT ENERGY-EFFICIENT BLUE E ELECTRONIC ENCLOSURE AIR CONDITIONER ROOF-MOUNTED BOLTED ON TOP OF ROLL-AROUND DUCTED BASE ADAPTER CAN COMBINE WITH DUCTS INSIDE YOUR CABINET FOR TARGETED COOLING COOLING CAPACITY: 5630 BTU COOLING OUTPUT TO L35/60HZ 1.65KW RATED OPERATING POWER: 115V 1PHASE 50/60HZ 10.1A STARTUP CURRENT: 27.2A RATED AIR THROUGHPUT: EXTERNAL CIRCUIT 942 CFM, INTERNAL CIRCUIT 289 CFM DIGITAL "COMFORT" TEMPERATURE CONTROLLER ELECTRIC CONDENSATE EVAPORATION PLUG-IN TERMINAL STRIP CONNECTOR EER: 2.13 REFRIGERANT: R134A RATED FOR 100% DUTY CYCLE OPERATING TEMPERATURE RANGE: 10 ... 55 OC SETTING RANGE: 20 ... 50OC LOW NOISE, SUITABLE FOR OFFICE USE SHEET STEEL CONSTRUCTION LOCKING CASTERS OVERALL DIMENSIONS: 29" X 19" X 30"H COOLING UNIT DIMENSIONS: 23-1/2" X 18-1/4" X 16-1/2"