Oil Patch Power Sale

WATSON HOPPER GXXTA WORK OVER RIG 102/250K DERRICK 500 HP 12.7L DETROIT SERIES 60 DIESEL ENGINE. ALLISON TRANSMISSION. 102' TALL DERRICK, 250,000# MAST. HAS ROD AND TUBING RACKING BOARD, WORK PLATFORM, AND HYDRAULIC LEVELING JACKS. BLOCK AND HOOK INCLUDED.

2010 GEFCO / AMERICAN AUGERS VR-330 DRILL RIG - ***UNUSED*** AMERICAN AUGERS USED VR-330 STANDARD OIL AND GAS DRILLING RIG 2010 SERIAL NUMBER VR3300050808 CAT C11 DIESEL ENGINES SAFE WORKING LOAD RATING: 330,000 LBS (150 TONNES) 1. BUILT TO API SPEC 4F SPECIFICATION FOR DRILLING AND WELL SERVICING STRUCTURES 2. CANADIAN DRILL RIG STANDARD STABILIZATION: 1. TWO STRUTS BETWEEN THE DERRICK AND THE TRAILER ARE THE SAFETY SUPPORTS ON THE BACK SIDE OF THE DERRICK. 2. TRAILER HAS 4 JACKS 2 AT THE REAR OF THE TRAILER AND 2 TOWARD THE GOOSENECK TRANSITION. THERE ARE 4 NON-HYDRAULIC SCREW JACKS PERMANENTLY WELDED INTO THE TRAILER 2 AT THE TILT CYLINDER ATTACHMENT POINT AND 2 AT THE REAR OF THE TRAILER TO HANDLE HALF OF THE DRILLING FORCES. 2 ADDITIONAL SCREW JACKS ARE ON THE SUBSTRUCTURE BEAM THAT CARRIES THE OTHER HALF OF THE DRILLING FORCES. 3. DRILL RIG MOUNTED ON TRIPLE-AXLE TRAILER, AIR RIDE SUSPENSION. COMES WITH A TANDEM STINGER AXLE FOR TRANSPORTATION ON ROADS. 4. 10MAX OVERALL TRANSPORT WIDTH 5. THE TRAILER JACKS RAISE THE RIG ENOUGH TO PROVIDE ABOUT 8 OF CLEARANCE BELOW THE DRILLING FLOOR. DERRICK: 1. SPACE FRAME CONSTRUCTION MADE MOSTLY OF PLATE HAVING TRIANGULATED LIGHTENING HOLES WHERE POSSIBLE. THE DESIGN WILL NOT REQUIRE A TRUSS FOR STIFFNESS. 2. REMOVABLE 15FT REAR SECTION ALLOWS SHORTER TRANSPORT LENGTH. 3. DESIGNED TO OPERATE ONLY IN THE VERTICAL POSITION 4. RANGE III DRILL PIPE COMPATIBLE LENGTH 5. 50 OF TOTAL CARRIAGE TRAVEL. 6. LADDER FULL LENGTH WITH HARNESS ATTACHMENTS. 7. 2 TELESCOPIC CYLINDERS ARE USED TO RAISE THE DERRICK. LOAD CHECK VALVES ARE INTEGRATED INTO THE CYLINDERS. A THIRD CYLINDER (SINGLE STAGE) HAS A CABLE ATTACHED TO THE ROD END AND CONTROLS THE DERRICK WHEN IT IS NEARLY VERTICAL. IT WILL PREVENT THE TELESCOPIC CYLINDERS FROM UNDERGOING AN OVERRUNNING LOAD. 8. 2 WINCHES ARE PROVIDED AT THE TOP OF THE DERRICK DRILL PIPE HANDLING SYSTEM: 1. SWING ARM TYPE OF HANDLING APPARATUS WITH OPPOSED JAW GRIPPERS THAT ROLL 180 DEGREES. 2. ALIGNMENT IS BY PATENT PENDING AMERICAN AUGERS FLOATING ASSEMBLY WHICH ENSURES RELIABLE ALIGNMENT OF PIPE. 3. THE PIPE HANDLER IS POWERED BY THE RIG. 4. THE CONTROLS ARE ELECTRIC OVER HYDRAULIC WITH SUFFICIENT CABLING TO OPERATE FROM THE DRILLERS CABIN 5. SUITABLE FOR 2 7/8 DRILL PIPE TO 8 COLLARS & 9 5/8 AND 13-5/8 CASING MAX LOAD 3000LBS. DRILLING FLOOR AND SUPPORT BEAM: 1. DRILLING STRUCTURE HAS A STEEL FLOOR COVERED IN HI-VIS ANTI SKID PLASTIC TRAC MAT A SLIP BOWL ATTACHES TO FLOOR 2. THE REAR OF THE TRAILER AND DRILLING FLOOR IS SUPPORTED BY A DEEP BEAM THAT ATTACHES TO THE BACK OF THE TRAILER STRUCTURE. THE BEAM HAS SCREW JACKS AT EACH END WHICH CONDUCT THE LOAD AGAINST 6 X 6 GROUND PLATFORMS. 3. (8) OF APPROXIMATE VERTICAL CLEARANCE FROM THE GROUND TO THE BOTTOM OF THE DRILLING FLOOR. 4. THE DRILLING FLOOR IS 14 DIAMOND PLATE AND IS SUPPORTED BY TUBULAR BRACES THAT ARE PINNED IN PLACE. 5. THE SLIP ASSEMBLY IS HYDRAULICALLY POWERED AND IS CONTROLLED FROM THE CABIN. CARRIAGE: 1. RACK AND PINION CARRIAGE DRIVE - SIX (6) PINION 2. 330,000 LBS. @ 44 FPM IN MAX PULL MODE 3. 200,000 LBS, @ 120 FPM IN MAX SPEED MODE 4. INFINITELY ADJUSTABLE PULL DOWN AND PULLBACK FORCE LIMITER 5. (6EA) BRAKES ARE SPRING SET HYDRAULIC RELEASE TYPE. 6. RACK AND PINION DESIGN 7. HOOK DEVICES HAVE TRIPLE ROLLER DESIGN AT TOP FRONT AND BOTTOM REAR. 8. POWERED GREASER LUBRICATES THE PINIONS PERIODICALLY 9. POWERED GREASER FOR DRILL PIPE THREADS IS REMOTE CONTROL. ROTARY DRIVE: 1. TOP HEAD TYPE WITH SLIP SPINDLE AND SLIP SUB 2. 30,000 FT-LBS MAX ROTARY TORQUE 3. (95) RPM MAX ROTARY SPEED 4. DIGITAL ROTARY TACHOMETER 5. DUAL PINION DRIVE 6. ROTARY BRAKES BETWEEN ROTARY MOTORS AND PLANETARIES 7. SLIP SPINDLE WITH 5-1/2 API-FH TOOL JOINT CONNECTION 8. 3" (76MM) FLUID COURSE IN THE ROTARY SPINDLE, 4 5,000PSI SWIVEL HOSE 9. INFINITELY ADJUSTABLE TORQUE LIMITER WRENCHES: 1. OPEN SIDE TYPE WITH OPPOSED JAW DESIGN USING 8 CLAMP CYLINDERS 2. HYDRAULICALLY MOVEABLE TO ALLOW CLEARANCE FROM THE DRILL STRING 3. ENTIRE ASSEMBLY CAN MOVE 12 UPWARD USING CYLINDER POWER. 4. CLAMPS ROLL ON CAM FOLLOWERS 5. QUICK CHANGE DIE HOLDERS 6. MAX. BREAKOUT TORQUE, 60,000 FT-LB 7. MAX. MAKEUP TORQUE, 60,000 FT-LB 8. GRIP RANGE 4 1/8 TO 10 3/4 9. OPERATOR ADJUSTABLE TORQUE LIMITERS FOR MAKEUP AND BREAKOUT FUNCTIONS 10. REMOTE CONTROL FROM CABIN 11. DESIGNED FOR EASY REMOVAL AND TRANSPORT HPU, (HYDRAULIC POWER UNIT): 1. 770 TOTAL HORSEPOWER - (2) TIER III CATERPILLAR C-11, 385 HP @ 2100 RPM 2. POSITIVE AIR SHUTOFF VALVE, EACH ENGINE 3. HYDROSTATIC DRIVE PUMPS 4. PRESSURE COMPENSATED PISTON PUMPS 5. ELECTRICAL POWER IS NOT PROVIDED FOR ANYTHING SUCH AS EXTERNAL LIGHTING, ELECTRIC TRASH PUMP, ETC. 6. THE HYDRAULIC AND MUD HOSES ARE CONTAINED IN A HOSE CARRIER. 7. AUXILIARY HYDRAULIC FLOW OF 30 GPM IS PROPORTIONALLY CONTROLLED FROM THE CABIN. 8. HYDRAULIC POWER FOR SLIPS PROVIDED AND CONTROLLED FROM CABIN. OPERATORS CONTROL PANEL AT DRILLERS CONSOLE: 1. ENGINE START/STOP, THROTTLE 2. FULL PROPORTIONAL CONTROLS ON

2015 PETERBILT 389 WINCH TRUCK - HYDRAULIC WINCH TRUCK - WINCH RATING 100K LBS, CUMMINS ISX-15 550HP. DIESEL ENG, FULLER 18-SPD. TRANS, STEER TIRE SIZE: 445/65R22.5, LIFT AXLE TIRE: 255/70R22.5, REAR AXLES: 11R24.5, 4 NEW GOOD YEAR REAR AXLE TIRES, NEW RADIATOR, ALL NEW BRAKES, FULL LOCKERS, 46K REAR AXLE GAWR, 20K FRONT AXLE GAWR, DOUBLE FRAME, FULL SLIDING 5TH WHEEL PLATE, FULL LENGTH REAR ROLLER S/N: 1XPXP4EX2FD282083

FRANKS ROCKET 658 D/D BACK-IN WELL SERVICE RIG P/B DETROIT 8V-71 ENG, ALLISON 4460 TRANS, PEMCO 96'H 180,000# MAST, 15" DBL HYD ROD & TUBING BOARDS, WORK PLATFORM, ALL MTD ON 4-AXLE CARRIER, MCKISSICK 100-TON 3-SHEAVE BLOCK

2006 GARDNER DENVER PZ9 1000 HP MUD PUMP - RUNS GREAT! 2006 GARDNER DENVER PZ9 1000 HP MUD PUMP POWERED BY (2) DETROIT SERIES 60, 14.0L 665HP DIESEL ENGINES ENGINE, W/ IN-LINE ENGINE COMPOUND, AIR VOLUME TANK, DIESEL DAY TANK, WORK LIGHTS, SKIDDED. - FULLY OPERATIONAL

GARDNER DENVER TEE MUD PUMP COUPLED TO A 6 CYLINDER DETROIT MODEL 6V71 ON A SKID.

GARDNER DENVER TEE PUMP SKID

AMERICAN BLOCK 1300HP TRIPLEX MUD PUMP - POWER RATING: 1300 HP RATED SPEED: 140 RPM STROKE: 10 IN MAX PRESSURE: 5000 PSI POWERED BY 2 ELECTRIC TRACTION MOTORS

2009 BOMCO RSF 1000 MUD PUMP - 2009 RSF1000 MUD PUMP DRIVEN BY MTU 12V2000 DIESEL ENGINE, ALLISON DP8962R TRANSMISSION. 5,613 HOURS, 5000 PSI, QUICK CHANGE CAPS, PULSATION DAMPENER, CHARGE PUMP

CANRIG 1050E-712 500 TON TOP DRIVE - TYPE: ELECTRIC / HYDRAULIC, RATED CAPACITY: 500 TONS, TEST/WORKING PRESSURE: 5000 PSI / PSI 23.6'L X 6'W X 9'H

NATIONAL 1300HP 10-P-130 TRIPLEX MUD PUMP - NATIONAL 10-P-130 TRIPLEX MUD PUMP RATED AT 1300 INPUT HORSEPOWER (969 KW) AT 140 STROKES PER MINUTE, WITH A 10-INCH (254 MM) STROKE POWERED BY (2) ELECTRIC TRACTION MOTORS S/N: RH1059-1

IDECO T-1000 TRIPLEX MUD PUMP POWERED BY D398 CAT DIESEL ENGINE

IDECO T-1000 TRIPLEX MUD PUMP POWERED BY D398 CAT ENGINE - SHOWING 1,208 HRS ENGINE STARTED ON 6/27/25

JETSTREAM 4200 SERIES UNX TRIPLEX PUMP SKID MOUNTED POWERED BY A JOHN DEERE 8.1L / 6-CYLINDER DIESEL ENGINE KEY PUMP SPECS: WIDE RANGE OF FLOW AND PRESSURE COMBINATIONS THREE PLUNGERS (TRIPLEX) DESIGN PLUNGER STROKE LENGTH 4.25 IN (108 MM) MAX POWER INPUT 325 HP (242 KW) 73.5 GPM AT 6,800 PSI (278 L/MIN AT 469 BAR) 11.9 GPM AT 40,000 PSI (45 L/MIN AT 2750 BAR) MAX FRAME LOAD 17, 750 IB (79 KW) TOTAL WEIGHT 1800 LB (820 KG) PUMP OIL CAPACITY 9 GAL (34 L)

2009 BOMCO RSF 1000 MUD PUMP - 2009 RSF1000 MUD PUMP DRIVEN BY MTU 12V2000 DIESEL ENGINE, ALLISON DP8962R TRANSMISSION. 14,240 HOURS

2014 TOTAL OILFIELD EQUIPMENT & SUPPLY COIL TUBING INJECTOR HEAD AND GOOSENECK. INJECTION HEAD - COIL TUBING. 100,000 POUND CAPACITY, DRESSED OUT FOR 2-3/8 TUBING, 111 MILES ON INJECTOR HEAD.

PZ9 POWERED BY CAT 3508 ENGINE, PUMP HOUSE

ZP275 ROTARY TABLE WITH MASTER BUSHING. LOADING RATE: 450 TONS GEAR RADIO: 3.67 TOTAL WEIGHT: 13650 LBS TABLE OPENING: 27 1/2 IN TABLE AXIS TO CENTER OF THE INNER TOW SPROCKET TEETH: 53 1/4 IN

TESCO 500 TON ECI 900HP SKIDDED, TESCO POWER MODULE MODEL PM 900 HP S/N T-31802-008, W/CONTROL PANEL, HEATING & A/C UNIT, FLUORESCENT LIGHTING, SKIDDED, HYD COOLING SYSTEM, HYD TANK, SERVICE LOOP INSIDE 8W X 8L STEEL BIN. - 7 UNITS

[2000-2030] TESCO 500 TON ECI 900HP S/N UNIT-910-1, SKIDDED, TESCO POWER MODULE MODEL PM 900 HP S/N T-31802-008, W/CONTROL PANEL, HEATING & A/C UNIT, FLUORESCENT LIGHTING, SKIDDED, HYD COOLING SYSTEM, HYD TANK, SERVICE LOOP INSIDE 8W X 8L STEEL BIN. - 7 UNITS

2001 PETERBILT 330 DATA VAN/OFFICE TRUCK - 2001 PETERBILT 330 S/A DATA VAN TRUCK, VIN-2NPNHD7X51M566953, P/B CAT 3126 DIESEL ENG, EATON 8-SPD TRANS W/ WT VAN BODY, HARRISON HYD GEN, (2) ROOMS W/ DESK & WORK AREAS, DATA CABLE REELS, AIR RIDE SUSP, 11R22.5 TIRES, BUDD WHEELS (85,688 ODOMETER MILES)

2002 JOHN EVANS MFG HI1652 40' FOOT CONTAINER TRAILER

[IDECO MUD MOVER 550] IDECO MUD MOVER 550 DUPLEX MUD PUMP. 7-1/4X15 INCH STROKE POWERED BY CAT 379 DIESEL ENGINE.

CLARK GPS25MB FORKLIFT - CLARK GPS25MB PNEUMATIC TIRED FORKLIFT; LPG, SHUTTLE, 4,000 LB CAPACITY, 188 IN MAST HEIGHT, 2-STAGE MAST, OPEN/CLOSE FORKS, SIDE SHIFT FULLY OPERATIONAL, HAS SOME LEAKS - HOURS: 3,130

GARDNER DENVER PZ7 - APPEARS TO BE REBUILT! GARDNER DENVER PZ7 S/N: 20350

2012 LETOURNEAU 500 TON AC TOP DRIVE WITH TRACKS AND SHIPPING SKID S/N: DDTD500150R1

SWABBING RIG - SWABBING RIG ON CRANE CARRIER. 12-15,000 FEET OF LINE DETROIT DIESEL 6V-92T ENGINE, ALLISON CLT-4460 TRANS 43' MAST SINGLE DRUM DRAWWORKS WITH AIR CLUTCH (BILL OF SALE ONLY)

WHEATLEY TRIPLEX PUMP POWERED BY DETROIT 4-71 ENGINE, RUNS GOOD, GOOD OIL PRESSURE

GARDENER DENVER PZ9 MUD PUMP WITH CAT 398 ENGINE - CAT 398 DIESEL ENGINE ENG S/N 5L95488 GARDENER DENVER PZ9 MUD PUMP

316 STAINLESS STEEL TANKER TRAILER, CENTER DISCHARGE, TANDEM AXLE, AIR RIDE S/N: 1A921403N1005098

14" ROTARY TABLE

14 INCH VERTICAL TURBINE PUMP - FLOWSERVE 14 INCH VERTICAL TURBINE PUMP, 1500 GPM, 20 HP ELECTRIC MOTOR S/N: 0801NP004450-12

FLOWSERVE 14 INCH VERTICAL TURBINE PUMP - 1500 GPM, 20 HP, 3 PH ELECTRIC MOTOR S/N: 0801NP004450-1

12 INCH 3 STAGE VERTICAL TURBINE PUMP GOULDS PUMPS 12 FDLO, 12 INCH, 3 STAGE VERTICAL TURBINE PUMP, 1800 GPM, 75 HP ELECTRIC MOTOR

BJ 500 TON SPIDER ELEVATOR 500 TON SPIDER ELEVATOR

GARDNER DENVER 400 TON BLOCK - WIRE GROOVE: 1-3/8 SHEAVE DIAMETER: 50 SIX (6) SHEAVES 8.6'L X 3'W X 4.6'H

DRILLING PARTS BASKET - BASKET FULL OF DRILLING PARTS, DRILL SUBS, BOP TROLLEY

COBRA CENTRIFUGAL PUMP SIZE: 5X6X11 MOTOR: 50//60HP, 50//60HZ, 3 PHASE VOLTS: 190/380 - 230/450

DRILLING PARTS BASKET - BASKET FULL OF DRILLING RIG PARTS, DRILL SUBS, BOP TROLLEY

MUD BOAT - MUD BOAT

2010 SCHLUMBERGER 425 CU FT VERTICAL DRY FRICTION REDUCER SILO, W/ (2) BASE MTD FILL/SUCTION HOSES ON REELS SER# 10-003

12 INCH, 3 STAGE VERTICAL TURBINE PUMP - GOULDS, 12 FDLO, 12 INCH, 3 STAGE VERTICAL TURBINE PUMP, 1800 GPM, 75 HP ELECTRIC MOTOR

CENTRIFUGAL PUMP SIZE: 6X5X14 MOTOR: 75HP, 60HZ, 3 PHASE VOLTS: 230/460

CENTRIFUGAL PUMP - CENTRIFUGAL PUMP SIZE: 250 - 5X6X14 MOTOR: 75HP, 60HZ, 3 PHASE VOLTS: 230/460

GOULDS 8X10 CENTRIFUGAL FLUID PUMP 60 HP 230/460 3 PHASE ELECTRIC MOTOR SER# C0609200044

SENTRY SWIVEL 5D-266 - MODEL 5D-266 WITH JUNK BOX, HANDLING TOOLS AND OTHER CONTENTS.

TRIPLEX PUMP PUMP

SKY TOP BREWSTER 250T BLOCK

2016 MISSION MAGNUM ELECTRICAL CENTRIFUGAL PUMP SKIDDED SIZE: 6X5X11 MOTOR: 60HP, 50HZ, 3 PHASE VOLTS: 230/460 S/N: BV789260

OIL WORKS 35C7 OWI 35C HYDRAULIC PIPE SPINNER - VERSATILITY: ACCOMMODATES PIPE SIZES RANGING FROM 2-7/8 DRILL PIPE TO 7 DRILL COLLARS, MAKING IT SUITABLE FOR VARIOUS DRILLING APPLICATIONS.