Food Beverage and Nutraceutical Processing and Packaging Equipment Auction

20 INCH WIDE STAINLESS STEEL CAP ELEVATOR WITH 3/4 HORSEPOWER MOTOR, HOPPER DIMENSIONS (INCHES): LENGTH: 48 WIDTH: 48 DEPTH: 36 BELT DIMENSIONS (INCHES): WIDTH: 20 CLEAT FLIGHT: 9 CLEAT HEIGHT: 5 DISCHARGE: 100 INCHES (APPROXIMATELY) OVERALL DIMENSIONS (INCHES): LENGTH: 109 WIDTH: 81 HEIGHT: 123 STAINLESS STEEL CONSTRUCTION MOUNTED ON A STAINLESS STEEL FRAME MOTOR: HORSEPOWER: 0.75 RPM: 1725 ELECTRICAL REQUIREMENTS: 3 PHASE, 60 HERTZ, 230/460 VOLTS

PHOENIX ENGINEERING GOPACKER 3000 VERTICAL FORM FILL SEAL BAGGER, INTERMITTENT TYPE POUCH PACKING MACHINE, PRODUCTION OUTPUT: UP TO 40 CYCLES PER MINUTE, MINIMUM PACKAGE DIMENSIONS: LENGTH: 2 INCHES WIDTH: 1 INCHES, MAXIMUM PACKAGE DIMENSIONS: LENGTH: 5 INCHES WIDTH: 4 INCHES, PNEUMATICS REQUIREMENTS: 80 PSI @ 4 C.F.M, ELECTRICAL REQUIREMENTS: 120 VOLTS, 60 HERTZ, 1 PHASE, 304 STAINLESS STEEL FRAME S/N:

BESTPACK MBD22-3 TOP AND BOTTOM TAPE CASE SEALER, PRODUCTION SPEED: UP TO 20 CASES PER MINUTE, DEPENDING ON SIZE AND APPLICATION. MINIMUM CASE DIMENSIONS: LENGTH: 6 INCHES WIDTH: 7.5 INCHES HEIGHT: 3 INCHES. MAXIMUM CASE DIMENSIONS: LENGTH: UNLIMITED WIDTH: 20 INCHES HEIGHT: 20.25 INCHES. INFEED/DISCHARGE HEIGHT RANGE: 23.5 - 30 INCHES. TAPE HEAD WIDTHS: 3 INCHES. PUSH BUTTON CONTROLS. APPROXIMATE OVERALL DIMENSIONS: LENGTH: 42 INCHES WIDTH: 28.8 INCHES HEIGHT: 75 INCHES. MOUNTED ON CASTERS. ELECTRICAL: 1 PHASE, 60 HZ, 110 VOLTS.

IMA BFB 3781AB OVERWRAPPER - USED IMA BFB HORIZONTAL FLOW WRAPPER WITH: SPEED: UP TO 40 BUNDLES PER MINUTE PRODUCT SIZE RANGE: MINIMUM DIMENSIONS: LENGTH: 50 MILLIMETERS WIDTH: 23 MILLIMETERS DEPTH: 58 MILLIMETERS MAXIMUM DIMENSIONS: LENGTH: 220 MILLIMETERS WIDTH: 90 MILLIMETERS HEIGHT: 330 MILLIMETERS SIDE BELT INFEED ELECTREICAL REQUIREMENTS: 460 VOLTS, 60 HERTZ, 3 PHASE OVERALL DIMENSIONS: LENGTH: 80 INCHES WIDTH: 56 INCHES HEIGHT: 65 INCHES MODEL: 3781AB

SOUTHERN CALIFORNIA PACKAGING ST1100 LABELER, SPEED: UP TO 1,100 LINEAR INCHES PER MINUTE, WEB WIDTH: 6 INCHES, CONVEYOR DIMENSIONS: WIDTH: 6 INCHES LENGTH: 92 INCHES, LABEL SIZE: MINIMUM: WIDTH: 0.5 INCHES LENGTH: 0.5 INCHES MAXIMUM: WIDTH: 6 INCHES LENGTH: 18 INCHES, CORE DIAMETER: 1 INCH, MOUNTED ON CASTERS, PUSH-BUTTON CONTROLS WITH DIGITAL READOUT, ELECTRICAL REQUIREMENTS: 120 VOLTS, 60 HERTZ, SINGLE PHASE

RO TUBE SYSTEM - USED RO TUBE WITH: LENGTH: 172 INCHES DIAMETER: 8 INCHES STAINLESS STEEL CONSTRUCTION

ROTATING FILLER FRAME, NOZZLE DIAMETER: 3/4 INCHES, STATION DIMENSIONS: LENGTH: 6.5 INCHES WIDTH: 3.25 INCHES (24) STATIONS, TOUCHSCREEN HMI, ELECTRICAL REQUIREMENTS: 130 VOLTS, 60 HERTZ, 1 PHASE, OVERALL DIMENSIONS: LENGTH: 39 INCHES WIDTH: 50 INCHES HEIGHT: 75 INCHES

WORLD CUP STAINLESS STEEL SINGLE HEAD ROTARY CUP SEALER, PRODUCTION SPEED: UP TO 30 CUPS PER MINUTE, SEAL RANGE: 1-10 OUNCES, NUMBER OF STATIONS: 8, CURRENT DIAMETER: 2.5 INCHES, CUP DENEST MAGAZINE, AREA TO ADD FILLER, PISTON FILLER NOT INCLUDED, MAGAZINE FOR PRE CUT SEALS, SEAL AREA, MOUNTED ON CASTERS FOR MOBILITY, STAINLESS STEEL CONSTRUCTION, LAST APPLICATION: PRE CUT SEALS ONTO A CUP

EXTRUDER HOPPER & SHAFT, MOTOR NEEDED

3995 GALLON STAINLESS STEEL SINGLE WALL TANK - USED COMAT STAINLESS STEEL TANK WITH: TANK CAPACITY: 3995 GALLONS TANK DIMENSIONS (INCHES): DIAMETER: 92 HEIGHT: 144 DISCHARGE DIMENSIONS (INCHES): FLANGED DIAMETER: 2.5 HEIGHT: 11 TOP INLET: 2 INCHES FLANGED MANWAY DIAMETER (INCHES): WIDTH: 18 HEIGHT: 12 OVERALL DIMENSIONS (INCHES): LENGTH: 94 WIDTH: 94 HEIGHT: 180 TOP MOUNTED MOTOR AGITATION PITCHED BOTTOM WITH CENTER DISCHARGE STEAM VENT STAINLESS STEEL CONSTRUCTION LAST APPLICATION: CHEESE MODEL: STVS150.1

OYSTAR TFS 10 TUBE FILLER AND SEALER, INFEED: 75.5 INCHES HIGH, INFEED TANK: GALLONS: 10, DIAMETER: 17.5 INCHES, DISCHARGE: 34 INCHES, DISCHARGE WIDTH: 4 INCHES, PRODUCT PLACEMENT DIAMETER: 2 INCHES, PRODUCT APERTURE: 2.5 INCH, BOTTOM TO TOP FILLER: LENGTH: 5 INCHES, WIDTH: 0.75 INCHES, SEAL BAR LENGTH: 4 INCHES

MFT AUTOMATION 250IP3 FRICTION FEEDERS TABLE (2) - HIGH-PERFORMANCE, VERSATILE MACHINE DESIGNED FOR PRECISE AND RELIABLE FEEDING OF A WIDE RANGE OF PRODUCTS IN PACKAGING AND PRINTING APPLICATIONS. ADVANCED FRICTION TECHNOLOGY ENSURES SMOOTH, CONSISTENT FEEDING OF MATERIALS LIKE PAPER, LABELS, AND CARTONS. EASY ADJUSTABILITY, QUICK SETUP, AND MINIMAL MAINTENANCE ENHANCE EFFICIENCY AND REDUCE DOWNTIME. IDEAL FOR HIGH-SPEED PRODUCTION ENVIRONMENTS. THROUGHPUT: UP TO 140 METERS PER MINUTE DEPENDING ON PRODUCT SIZE AND APPLICATION. MAXIMUM BELT SPEED: UP TO 200 METERS PER MINUTE. MINIMUM PRODUCT DIMENSIONS: LENGTH: 20 MM, WIDTH: 20 MM, THICKNESS: 0.075 MM. MAXIMUM PRODUCT DIMENSIONS: LENGTH: 325 MM, WIDTH: 200 MM, THICKNESS: 25 MM. PRODUCT MAGAZINE: 750 MM. INFRARED SENSOR FOR ACCURATE COUNT. ELECTRICAL: 1 PHASE, 50-60 HZ, 115/230 VOLTS. PREVIOUSLY USED IN PHARMACEUTICAL FACILITY. S/N: NOT SPECIFIED

E PAK 10 HEAD INLINE PRESSURE GRAVITY FILLER WITH 15' LONG CONVEYOR, 10 FILING HEADS (CAPABLE OF HOLDING UP TO 20 HEADS), FILL HEADS DIAMETER: 3/8 INCHES, CONVEYOR: 15 FEET LONG 4.5 INCHES WIDE, STANDARD LINE HEIGHT RANGE: 32 TO 38 INCHES FROM GROUND, TOOL-LESS ADJUSTABLE RAIL BRACKETS, VARIABLE SPEED CONTROLLER, 304 STAINLESS STEEL HEAVY DUTY FRAME, 316 STAINLESS STEEL 3/4" PNEUMATIC ACTUATED FILL VALVES, BRAIDED PVC TUBING AND FITTINGS, ALLEN BRADLEY/MICROLOGIX 1200 CONTROLS WITH NEMATRON TOUCH SCREEN, AUTOMATIC SET UP CAPABILITIES, IN TANK FLOAT, DRIP TRAY, BOTTLE INDEXING SYSTEM, PHOTO SENSOR/COUNTING SYSTEM, ELECTRICALS: 110 VOLTS / 1 PHASE / 50-60 HERTZ, COMPRESSED AIR: 80 - 100 PSI

ACF 2000 STAINLESS STEEL AUTOMATIC CAPSULE FILLER, CAPACITY: UP TO 120,000 CAPSULES PER HOUR, CAPABLE OF RUNNING SIZES #00, #0, #1, #2, #3, #4, #5 (TOOLING NOT INCLUDED), ADJUSTABLE FILLING WEIGHT, MAIN DRIVE: 2 HORSEPOWER, AUGER DRIVE: 1/2 HORSEPOWER, VACUUM PUMP: 1.5 HORSEPOWER, STAINLESS STEEL CONSTRUCTION, TOUCH SCREEN CONTROLS, ELECTRICAL REQUIREMENTS: 220 VOLTS, 60 HERTZ, 3 PHASE, OVERALL DIMENSIONS: LENGTH: 956 MILLIMETERS, WIDTH: 1096 MILLIMETERS, HEIGHT: 2030 MILLIMETERS

EAGLE 50 CUBIC FOOT SINGLE SHAFT RIBBON BLENDER WITH AUGER FEEDER DISCHARGE. CAPACITY: 50 CUBIC FEET. TROUGH DIMENSIONS: LENGTH: 60 INCHES WIDTH: 32 INCHES DEPTH: 45 INCHES. AUGER DIMENSIONS: LENGTH: 96 INCHES DIAMETER: 10 INCHES. DISCHARGE DIAMETER: 10 INCHES. PUSH BUTTON CONTROLS. 1 HORSEPOWER MOTOR. ROTATIONS PER MINUTE: 1750. MILD STEEL CONSTRUCTION. ELECTRICAL REQUIREMENTS: 480 VOLTS, 60 HERTZ, 3 PHASE.

MUELLER 100-LITER REACTOR KETTLE WITH CORIOLIS FLOW METER. CAPACITY: 100 LITERS (26.4 GALLONS). TANK DIMENSIONS: DEPTH: 22 INCHES, DIAMETER: 32 INCHES. MAXIMUM WORKING PRESSURE: VESSEL: 100 PSI @ 300F, FULL VACUUM. HEAT TRANSFER SURFACE: 150 PSI @ 300F, FULL VACUUM. TOP INLETS: 9 TOTAL (X5): 2-INCH OUTSIDE DIAMETER, 1-INCH INSIDE DIAMETER; (X4): 3.5-INCH OUTSIDE DIAMETER, 2.75-INCH INSIDE DIAMETER. ACCESS WAY: 6.5 INCHES IN DIAMETER. ENDRESS+HAUSER CORIOLIS FLOW METER HOOKUPS (X3): OUTSIDE DIAMETER: 2 INCHES, INSIDE DIAMETER: 1.25 INCHES. OVERALL DIMENSIONS: LENGTH: 47 INCHES, WIDTH: 42 INCHES, HEIGHT: 85 INCHES. CONSTRUCTION: 316 STAINLESS STEEL. MOTOR: 3 HP. MOTOR ELECTRICAL: 208-230/460 V, 60 HZ, 3,535 RPM, THREE PHASE.

STAINLESS STEEL VOLUMETRIC CUP FILLER FOR DRY FREE-FLOW PRODUCTS - USED ALL-FILL CUP FILLER WITH: PRODUCTION RATE: UP TO 100 CUPS PER MINUTE DEPENDING ON PRODUCT AND APPLICATION FILL WEIGHT RANGE: MINIMUM: 0.25 OUNCES MAXIMUM: 15 POUNDS HOPPER CAPACITY: 16 GALLONS INTERIOR HOPPER DIAMETER: 22 INCHES 7 INCH HMI TOUCH SCREEN CONTROLS FOOT PEDAL OPERATION (4) ROTARY DOSING HEADS STAINLESS STEEL CONTACT PARTS ELECTRICAL REQUIREMENTS: 220 VOLTS, 60 HERTZ, 1 PHASE

KICE 3E6 MULTI-ASPIRATOR PARTICLE DENSITY SEPARATOR, USED KICE MULTI-ASPIRATOR WITH EFFICIENT PRODUCT DENSITY SEPARATION CAPABILITIES. SEPARATES LIGHT MATERIALS FROM HEAVY ONES. APPLICATIONS IN COMMERCIAL FOOD PROCESSING AND OTHER INDUSTRIES THAT RELY ON DRY SEPARATION SYSTEMS. REDUCES DUST, EXPLOSIVE FINES AND INFESTATIONS. REMOVES FINES AND DUST FROM FINISHED PELLETS, CEREALS AND PRILLS. SEPARATES DIFFERENT TYPES OF PLASTICS IN REGRIND/RECLAIM SYSTEMS. DE-DUSTS FERTILIZER PRILLS. CLEANS GRAIN BY REMOVING DAMAGED KERNELS AND FOREIGN MATERIAL. SEPARATES HULLS OR SHELLS FROM SEEDS OR NUTS. ALL MATERIAL OF CONSTRUCTION AND HARDWARE: 304L SS. MOTOR: 1 HORSEPOWER, 3450 RPM, 230/460/3/60

HOPPMANN CORPORATION FT50-21 47 INCH DIAMETER SS STAINLESS STEEL CENTRIFUGAL CAP SORTER WITH BELT FEEDER. HOPPMANN FT50-21 BOWL FEEDER: BOWL DIAMETER: 47 INCHES, BOWL RIM WIDTH: 4.12 INCHES, BOWL RIM TO BOTTOM OF FRAME: 24.88 INCHES, DISCHARGE HEIGHT: 36 INCHES (APPROXIMATELY). MOTOR: 0.75 HORSEPOWER. WEIGHT: 1050 POUNDS. STAINLESS STEEL CONSTRUCTION. WB-6 WIDE BELT PREFEEDER: CAPACITY: 6 CUBIC FEET, OVERALL LENGTH: 72 INCHES, OVERALL WIDTH: 51 INCHES, INFEED HEIGHT: 94 INCHES. UPPER BELT HORSEPOWER: 0.5, LOWER BELT HORSEPOWER: 0.033. STAINLESS STEEL CONSTRUCTION. VARIABLE SPEED CONTROL. PUSH BUTTON CONTROLS. MOUNTED ON A STAINLESS STEEL FRAME. ELECTRICAL: 3 PHASE, 60 HERTZ, 230 VOLTS. MODEL: FT50-21

KENTEX TK850-HA STAINLESS STEEL TUBE FILLER, UP TO 50 TUBES PER MINUTE, 50 LITER HOPPER, 2-320 ML FILL RANGE, 10-52 MM TUBE DIAMETER, 280 MM MAX TUBE LENGTH, 36 INCH DISCHARGE HEIGHT, 316 STAINLESS STEEL CONTACT PARTS, MOUNTED ON CASTERS, 5 BAR AIR, 240 V / 60 HZ / 40 A / THREE PHASE. LAST APPLICATION: FILLING 2 AND 4 OUNCE TUBES OF GEL. S/N:

ELECTRIC BOILER, 120 KW, 480V, 150 PSI MAX WORKING PRESSURE. NEVER PUT INTO PRODUCTION. S/N:

NORDENMATIC 700 AUTOMATIC TUBE FILLER AND SEALER, FILL RANGE: MINIMUM: 1 MILLILITER MAXIMUM: 600 MILLILITERS TUBE SIZE RANGE: MINIMUM: DIAMETER: 10 MILLIMETERS LENGTH: 50 MILLIMETERS MAXIMUM: DIAMETER: 620 MILLIMETERS LENGTH: 280 MILLIMETERS (24) POCKET ROTARY PUCK CAROUSEL AUTO TUBE LOADER TUBE CLEANER ELECTRICAL REQUIREMENTS: 220 VOLTS, 60 HERTZ, 3 PHASE

TAYLOR PRODUCTS APV BAG FILLING MACHINE FOR 50 POUND BAGS, AUTOMATED SYSTEM FOR ACCURATE AND CONSISTENT FILLING, ADVANCED CONTROLS, NEMA12 ENCLOSURE, TUBULAR CARBON STEEL FRAME, STAINLESS STEEL CONTACT PARTS. CAPABLE OF RUNNING UP TO 50 POUND BAGS, OUTPUT UP TO 5 BAGS PER MINUTE, 4,000 CUBIC INCH PRODUCT HOPPER, ACCURACY UP TO 4%. AIR REQUIREMENTS: 90 PSI. ELECTRICAL REQUIREMENTS: 230/460 VOLTS, 3 PHASE, 60 HERTZ. TRV-1000 ROBOTIC BAG PLACER.

POPCORN POPPING AND SEASONING LINE WITH CONVEYOR AND TRANSFORMER. POPPING KETTLE: DIAMETER: 40 INCHES, STRAIGHT WALL HEIGHT OF KETTLE: 16 INCHES. CONVEYOR: WIDTH: 24 INCHES, OVERALL DIMENSIONS (INCHES): LENGTH: 67, WIDTH: 59, HEIGHT: 67. CLEATED CONVEYOR: CONVEYOR DIMENSIONS (INCHES): LENGTH: 160, WIDTH: 34.5, HEIGHT: 60. CLEAT DIMENSIONS (INCHES): HEIGHT OF CLEATS: 1.5, DISTANCE BETWEEN CLEATS: 8. MOTOR: 380 V / 60 HZ / 2 A / 1,700 RPM. 70 KVA TRANSFORMER: CE COMPLIANT, OVERALL DIMENSIONS (INCHES): LENGTH: 29.5, WIDTH: 19, HEIGHT: 31, INPUT: 208 VAC / 194 A, OUTPUT: 380 VAC / 106 A, FREQUENCY: 50 / 60 HZ. SEASONING DRUM: OVERALL DIMENSIONS (INCHES): LENGTH: 75, WIDTH: 51, HEIGHT: 69.

MANESTY BB4 35 STATION DOUBLE SIDED ROTARY TABLET PRESS - PRODUCTION OUTPUT: UP TO 210,000 TABLETS PER HOUR DEPENDING ON SIZE AND APPLICATION. MAXIMUM TABLET SIZE: DIAMETER: 0.625 INCHES (16 MM), THICKNESS: 0.34375 INCHES (8.5 MM), DEPTH OF FILL: 0.6875 INCHES (17.5 MM). MAXIMUM TABLET FORMING PRESSURE: 6.5 TONS. PRESSURE ROLL DIAMETER: 8 INCHES (203 MM). PUNCH PITCH DIAMETER: 15.125 INCHES (384 MM). TURRET SPEED: FROM 17 TO 50 RPM. TABLET DIE: TYPE: B, DIAMETER: 1.1875 INCHES (30.1 MM), HEIGHT: 0.875 INCHES (22.22 MM). UPPER/LOWER PUNCH LENGTH: 5.25 INCHES (133 MM). PUNCH BODY DIAMETER: 0.75 INCHES (19.05 MM). PUSH BUTTON CONTROLS. APPROXIMATE OVERALL DIMENSIONS: WIDTH: 32 INCHES (812 MM), DEPTH: 37 INCHES (940 MM), HEIGHT: 72 INCHES (1834 MM). STAINLESS STEEL CONSTRUCTION. ELECTRICAL: 3 PHASE.

HUDSON SHARP NG4331018 FOOD SERVICE GLOVE PRODUCTION LINE, PRODUCTION SPEED: UP TO 400 PIECES PER MINUTE, UNWIND SHAFT FILM DIAMETER: 20 INCHES, EXIT CONVEYOR DIMENSIONS: LENGTH: 90 INCHES WIDTH: 40 INCHES, TURNING BAR ANGLE: 45 DEGREES, INCLUDES: UNWINDER, V-FOLDER, CUFF CUT PUNCH SECTION, MAIN NIP SECTION, HEAT SEAL SECTION, EXIT CONVEYOR, GLOVE STACK QUANTITY CONTROL, THREAD SPEED CONTROL, TOGGLE BETWEEN PICK 2 AND PICK 4 GLOVES, LIFETIME PRODUCT COUNT, HMI TOUCHSCREEN INTERFACE, PUSH BUTTON CONTROLS, ELECTRICAL REQUIREMENTS: 240/480 VOLTS, 60 HERTZ, 1 PHASE, OVERALL DIMENSIONS: LENGTH: 242 INCHES WIDTH: 72 INCHES HEIGHT: 97 INCHES, LAST USED FOR PRODUCTION OF FOOD SERVICE GLOVES

APACKS EXACT MASS DUAL HEAD FLOW METER LIQUID FILLER, FILL SIZE RANGE: 0.5 OUNCE TO 5 GALLONS, TWO (2) SANITARY FLOW METERS, TWO (2) BOTTOM-CLOSE FILL HEAD VALVES, MAXIMUM CONTAINER HEIGHT: 12 INCHES, CONTAINER INFEED HEIGHT: 23 INCHES, OVERALL DIMENSIONS (INCHES): LENGTH: 86 WIDTH: 92 HEIGHT: 84.5, BOTTOM-CLOSE FILL HEAD, PNEUMATIC BOTTOM-UP FILL HEADS, 316 STAINLESS STEEL PRESSURE VESSEL, CIP SYSTEM WITH INTERIOR SPRAY BALL, 304 TUBULAR STAINLESS STEEL FRAME, ADJUSTABLE LEVELING LEGS, TOOLLESS FILL HEAD ADJUSTMENT

KM GRANDPACK 12 BASKET STATIC STEAM RETORT WITH 2 DOOR, MANUAL LOADING. STYLE: STATIC STEAM CAPACITY: 12 BASKETS PRESSURE RATING: MAWP: 43.5 PSI AT 302 F (300 KPA AT 150 C) MDMT: 32 F AT 43.5 PSI (0 C AT 300 KPA) BASKET DIMENSIONS (INCHES): LENGTH: 40 WIDTH: 32 HEIGHT: 27.5 CHAMBER DIMENSIONS: LENGTH: 41 FEET DIAMETER: 48 INCHES OVERALL DIMENSIONS: LENGTH: 44 FEET WIDTH: 54 INCHES HEIGHT: 54 INCHES INFEED: 2 DOORS, MANUAL SWING DOOR BASKET ROLLER RAILS WITH DOUBLE STAINLESS STEEL CHAIN NO. 80 AND GEAR MOTOR DRIVE 3.0 HP FOR BASKET LOADING/UNLOADING DOUBLE DOOR LOCKING SYSTEM INSULATION: THERMAL INSULATION 50 MM THICK BY ROCKWOOL 80K AND MIRROR POLISHED STAINLESS STEEL CLADDING 0.7 MM THICK. BLOCK AND BLEED VALVES FOR AIR AND WATER SIGHT GLASS WITH SENSORS FOR WATER LEVEL CONTROL STEAM VALVE: SPIRAX SARCO TYPE LE33 COMPRESSED AIR VALVE: OMAL SAFETY VALVE: ARI X 2 SET (ASME U-STAMP) PRESSURE GAUGE: 0-6 BARS VESSEL PRESSURE SENSOR: ESI MODEL GS4200 MIG THERMOMETER: TAYLOR SCALE 75-135 C. DIGITAL THERMOMETER: WAHL CIRCULAR CHART RECORDER: HONEYWELL MODEL DR4500AT ASME: ASME U-STAMP CERTIFICATE WITH NATIONAL BOARD NO. REGISTRATION TO MEET PRESSURE VESSEL REGULATION IN GA INCLUDING ENGINEERING, MANUFACTURING, TESTING, INSPECTION TO ASME SECTION VIII, DIVISION I, EDITION 2021. CONTROL SYSTEM: ALLEN BRADLEY PROGRAMMABLE LOGICAL CONTROLLER (PLC) MODEL MICROLOGIX 1400 CONSTRUCTION: STAINLESS STEEL SUS 304 6MM THICK ELECTRICAL: 3 PHASE, 60 HERTZ, 480 VOLTS CONTROL VOLTAGE: 120 VOLTS SIGNAL VOLTAGE: 24VDC LAST APPLICATION: TUNA CANS AT A 5, 7, AND 12 OUNCE WEIGHT. TYPICALLY CYCLE WAS 2 HOURS AND 45 MINUTES. 4 POUND PRODUCT WAS ALSO RAN ON THIS A 5 + HOUR CYCLE.

VLS TECHNOLOGIES FVV 35 VERTICAL PLATE FILTER, FILTERING SURFACE: 33.8 SQUARE METERS, MAXIMUM WORKING PRESSURE: 8 PSI, FILTER SCREEN SIZE: 80 MICRONS, DOSING TANK FOR FILTER AIDS PREPARATION, AGITATION, MEMBRANE DOSING PUMP WITH ADJUSTABLE FLOW, CENTRIFUGAL FEEDING PUMP, FILTER CHAMBER WITH PRESSURE GAUGE, AISI 304 CONTROL BOARD WITH PUSH BUTTON CONTROLS, PRESSURIZTION DEVICE COMPLETE OF INTERCEPTION VALVE, BREATHER BEER DEVICE ON HEAD PUMP, PRESSURE SWITCH, DISHED LID WITH C-CLAMPS, CENTER BOTTOM VALVE FOR CAKE DISCHARGE, ELECTRICAL MOTOR VIBRATOR FOR DRY CAKE DISCHARGE, (2) BUTTERFLY VALVES FOR PRODUCT INLET, STAINLESS STEEL FEED PUMP, MOUNTED ON CASTERS, 304 STAINLESS STEEL CONSTRUCTION, ELECTRICAL REQUIREMENTS: 480 VOLTS, 60 HERTZ, 3 PHASE, OVERALL DIMENSIONS: LENGTH: 3200 MILLIMETERS, WIDTH: 1850 MILLIMETERS, HEIGHT: 2600 MILLIMETERS

RONTECH MF FRICTION FEEDER, UP TO 2500 PRODUCTS PER MINUTE, PRODUCT THICKNESS UP TO 20 MILLIMETERS, MAX PRODUCT DIMENSIONS LENGTH 1500 MILLIMETERS WIDTH 530 MILLIMETERS, MIN PRODUCT DIMENSIONS LENGTH 30 MILLIMETERS WIDTH 30 MILLIMETERS, INFEED CONVEYOR DIMENSIONS LENGTH 82 INCHES WIDTH 3 INCHES, MAX WIDTH 6 INCHES, DISCHARGE DIMENSIONS LENGTH 14 INCHES WIDTH 6.5 INCHES HEIGHT 40 INCHES, POSITIONING ACCURACY +/- 1 MILLIMETER, HMI ROTATABLE 8.4 INCH COLOR TOUCH SCREEN, SERVO DRIVEN, STAINLESS STEEL CONSTRUCTION, AIR PRESSURE 5 BAR, ELECTRICAL REQUIREMENTS 230 VOLTS, 50/60 HERTZ

HUIJI PHARMACEUTICAL INSPECTOR MACHINE - INSPECTION MACHINE FOR CAPSULES, SOFTGELS OR GUMMIES! INCLUDES LIGHT TO VIEW AND AIR SYSTEM. LOW USAGE

PACKLAB FRONT BACK AND WRAPAROUND LABELER, VERSATILE LABELING MACHINE DESIGNED TO APPLY LABELS TO BOTH THE FRONT AND BACK OF CONTAINERS, AS WELL AS WRAPAROUND LABELS FOR CYLINDRICAL PRODUCTS. FEATURES ADJUSTABLE SETTINGS TO ACCOMMODATE VARIOUS CONTAINER SIZES AND LABEL TYPES. OPERATES AT HIGH SPEEDS, ENSURING EFFICIENT AND PRECISE LABEL APPLICATION. OUTPUT: UP TO 80 INCHES PER MINUTE DEPENDING ON LABEL SIZES. CONVEYOR DIMENSIONS: 3.25 INCHES WIDE X 116 INCHES LONG. FRONT/BACK LABEL SIZE RANGE: WRAP BELT: 23 INCHES LONG X 4 INCHES. WEB WIDTH: 7.5 INCHES. 1.5 INCH DIAMETER INNER CORE. ELECTRICAL REQUIREMENTS: 480 / 50/60 HERTZ / 3 PHASE.

TECH FOR FOOD ROLL IT STAINLESS STEEL FOOD ROLLER, USABLE ROLL WIDTH: 420 MILLIMETERS, USABLE ROLL DIAMETER: 8-73 MILLIMETERS, ROLLING PERFORMANCE: 1 TRACK UP TO 50 ROLLS PER MINUTE, 2 TRACKS UP TO 100 ROLLS PER MINUTE, 4 TRACKS UP TO 200 ROLLS/MIN, INFEED HEIGHT: 42 INCHES, TOUCH SCREEN CONTROLS, MOUNTED ON STAINLESS STEEL LEGS, STAINLESS STEEL CONSTRUCTION, ELECTRICAL: 230 VOLTS, 50/60 HERTZ, 3 PHASE, 13 AMPS

SOUTHERN CALIFORNIA ST1100 FRONT AND BACK LABELER, SPEED: UP TO 1,100 LINEAR INCHES PER MINUTE, WEB WIDTH: 6 INCHES, CONVEYOR DIMENSIONS (MISSING BELT): WIDTH: 6 INCHES LENGTH: 92 INCHES, LABEL SIZE: MINIMUM: WIDTH: 0.5 INCHES LENGTH: 0.5 INCHES MAXIMUM: WIDTH: 6 INCHES LENGTH: 18 INCHES, CORE DIAMETER: 1 INCH, MOUNTED ON CASTERS, PUSH-BUTTON CONTROLS WITH DIGITAL READOUT, ELECTRICAL REQUIREMENTS: 120 VOLTS, 60 HERTZ, SINGLE PHASE

INLINE FILLING SYSTEMS AUTOMATIC CAPPING SYSTEM - USED AUTOMATIC CAPPING SYSTEM WITH: CURRENT CAP SIZE: 24 MM VARIABLE SPEED CONTROLS CAP FEEDER DIAMETER: 24 INCHES HOPPER DIMENSIONS: LENGTH: 31 INCHES WIDTH: 36.5 INCHES DEPTH: 26 INCHES STAINLESS STEEL CONSTRUCTION ADJUSTABLE HEIGHT LEGS PNEUMATIC REQUIREMENTS: 80 PSI AT 7 CUBIC FEET PER MINUTE MOTOR: 0.5 HORSEPOWER, 1725 RPM ELECTRICAL: 110 VOLTS, 50/60 HZ

STAINLESS STEEL STEAM TUNNEL, APERTURE DIMENSIONS: WIDTH: 9.5 INCHES HEIGHT: 19 INCHES TUNNEL LENGTH: 79 INCHES INFEED/DISCHARGE HEIGHT: 22 INCHES EXHAUST BLOWER MAXIMUM: 592 CFM AIR REQUIREMENTS: 80 PSI BLOWER MOTOR: 1 HORSEPOWER, 3,450 RPM OVERALL DIMENSIONS: LENGTH: 79 INCHES WIDTH: 24 INCHES HEIGHT: 74 INCHES STAINLESS STEEL CONSTRUCTION ANALOG CONTROLS ELECTRICALS: 3 PHASE, 15 AMPS, 220 VOLTS

METTLER TOLEDO C3130 4.75 INCH WIDE BELT CHECKWEIGHER WITH AIR BLOW REJECT. THROUGHPUT: UP TO 200 PACKAGES/MINUTE, APPLICATION DEPENDENT. WEIGHING RANGE (GRAMS): MINIMUM: 20 MAXIMUM: 6,000. ACCURACY: 0.5 GRAMS (500 MG). WEIGH BELT DIMENSIONS (INCHES): LENGTH: 11 WIDTH: 4.75. INFEED LENGTH: 11 INCHES. INFEED HEIGHT: 33 INCHES. DISCHARGE LENGTH: 17 INCHES. REJECT: AIR BLAST. OVERALL DIMENSIONS (INCHES): LENGTH: 40 WIDTH: 38 HEIGHT: 53. AIR: 80 PSI. ELECTRICAL: 120/240 VAC, 50/60 HZ, SINGLE PHASE.

CANCO 610-1-HUL SEMI-AUTOMATIC EMPTY CAN DEPALLETIZER, UP TO 300 CANS PER MINUTE. SPEEDS: 20 TO 300 CPM. CAPABLE OF DEPALLETIZING METAL, GLASS, AND PLASTIC CONTAINERS. PALLET INFEED CONVEYOR (INCHES): LENGTH: 84 WIDTH: 33. EMPTY PALLET DISCHARGE CONVEYOR (INCHES): LENGTH: 84 WIDTH: 33. 1 HP HYDRAULIC LIFT TABLE FOR PRODUCT PALLETS UP TO 58" LONG X 45" WIDE X 57" HIGH. 44" WIDE X 4" HIGH MANUAL PUSH BAR SWEEP CARRIAGE. PRODUCT DISCHARGE CONVEYOR (INCHES): LENGTH: 55 WIDTH: 55. ELECTRICAL REQUIREMENTS: 3 PHASE, 60 HERTZ, 480 VOLTS. LAST APPLICATION: 16 OUNCE ALUMINUM CONTAINERS.

ACCUTEK STAINLESS STEEL 6 SPINDLE CAPPER - USED ACCUTEK INLINE CAPPER WITH: NUMBER OF SPINDLES: 6 CENTRIFUGAL ORIENTATION BOWL DIAMETER: SIDE GRIPPER BELT HEIGHT: 1 INCH LENGTH: 34 INCHES STAINLESS STEEL CONSTRUCTION ELECTRICAL: VOLTS: 110, HERTZ: 60 PHASE:1 AIR REQUIREMENTS: 60 PSI LAST RUNNING: 32 MM CAPS

CONFLEX FUSION INTERMITTENT MOTION SIDE SEALER, MINIMUM PRODUCT DIMENSIONS: LENGTH: 2 INCHES WIDTH: 1 INCHES HEIGHT: 0.125 INCHES MAXIMUM PRODUCT DIMENSIONS: LENGTH: INFINITE WIDTH: 22 INCHES HEIGHT: 10 INCHES OVERALL DIMENSIONS: LENGTH: 79 INCHES WIDTH: 57.5 INCHES HEIGHT: 59.5 INCHES SEAL BAR WIDTH: 24 INCHES MAXIMUM FILM WIDTH: 32 INCHES MAXIMUM ROLL DIAMETER: 14 INCHES INFEED HEIGHT: 34.75 INCHES SELVAGE WINDER HMI TOUCH SCREEN CONTROLS AIR REQUIREMENTS: 80 PSI ELECTRICAL REQUIREMENTS: 230 VOLTS, 60 HERTZ, 1 PHASE

1997 GEI MATEER BURT 408D MK V ROLL THROUGH HOT MELT GLUE CAN LABELER. OUTPUT: UP TO 500 PRODUCTS PER MINUTE. PRODUCT SIZE RANGE: DIAMETER: 1-3/4 INCH TO 4-1/2 INCHES, HEIGHT: 1-9/16 INCH TO 10-1/12 INCHES. LABEL SIZE RANGE: LENGTH: 4-5/8 INCH TO 15 INCHES, WIDTH: 1-1/4 INCH TO 9-1/4 INCHES. DISCHARGE HEIGHT: 60 INCHES. OVERALL DIMENSIONS: LENGTH: 62 INCHES, WIDTH: 32 INCHES, HEIGHT: 82 INCHES. MAGAZINE DIMENSIONS: WIDTH: 16 INCHES, HEIGHT: 10 INCHES. STEEL CONSTRUCTION. MOTOR ELECTRICAL: 460 V, 3.2 A, 60 CYCLE, 3-PHASE. HEATER ELECTRICAL: 460 V, 3.2 A, 1450 W. LAST RAN: 208-401.

1993 GEI MATEER BURT 408D ROLL THROUGH HOT MELT GLUE CAN LABELER, OUTPUT: UP TO 500 PRODUCTS PER MINUTE, PRODUCT SIZE RANGE: DIAMETER: 1-3/4 INCH TO 4-1/2 INCHES, HEIGHT: 1-9/16 INCH TO 10-1/12 INCHES, LABEL SIZE RANGE: LENGTH: 4-5/8 INCHES TO 15 INCHES, WIDTH: 1-1/4 INCH TO 9-1/4 INCHES, DISCHARGE HEIGHT: 60 INCHES, OVERALL DIMENSIONS: LENGTH: 62 INCHES, WIDTH: 32 INCHES, HEIGHT: 82 INCHES, MAGAZINE DIMENSIONS: WIDTH: 16 INCHES, HEIGHT: 10 INCHES, VALCO HOT MELT GLUE SYSTEM, STEEL CONSTRUCTION, MOTOR ELECTRICAL: 440 V, 3.8 A, 60 CYCLE, 3-PHASE, HEATER ELECTRICAL: 440 V, 3000 W, LAST RAN: 208-401

1982 MATEER-BURT 408D ROLL THROUGH HOT MELT GLUE CAN LABELER. OUTPUT: UP TO 500 PRODUCTS PER MINUTE. PRODUCT SIZE RANGE: DIAMETER: 1-3/4 TO 4-1/2 INCHES, HEIGHT: 1-9/16 TO 10-1/12 INCHES. LABEL SIZE RANGE: LENGTH: 4-5/8 TO 15 INCHES, WIDTH: 1-1/4 TO 9-1/4 INCHES. DISCHARGE HEIGHT: 60 INCHES. OVERALL DIMENSIONS: LENGTH: 62 INCHES, WIDTH: 32 INCHES, HEIGHT: 82 INCHES. MAGAZINE DIMENSIONS: WIDTH: 16 INCHES, HEIGHT: 10 INCHES. STEEL CONSTRUCTION. MOTOR ELECTRICAL: 230V, 15 A, 60 CYCLE, 3-PHASE. HEATER ELECTRICAL: 230 V, 1340 W. LAST RAN: 208-401.

HMC IMF 7-14 STAINLESS STEEL HORIZONTAL FORM FILL AND SEAL BAGGER, PRODUCTION SPEED: 50-70 BAGS PER MINUTE, MAX BAG DIMENSIONS: WIDTH: 5.75 INCHES DEPTH: 9.5 INCHES, MIN BAG SIZE: WIDTH: 3 INCHES DEPTH: 3 INCHES, BAG OPTIONS: GUSSET ZIPPER POUCH, DUPLEX CAPABLE, MAX ROLL DIAMETER: 24 INCHES, PRODUCT FLOW: LEFT TO RIGHT, CURRENT FILL HEAD DIAMETER: 2 INCHES, CHANGE PART INCLUDED FOR 2.5 INCH DIAMETER HEAD, NITROGEN PLUNGE, BAG KICKER, TEAR NOTCH, TOUCH SCREEN CONTROLS, MARKEM IMAJE INK JET PRINTER, SERVO DRIVEN FILM REPOSITIONER, PLUNGED NITROGEN ROUTER, ELECTRICAL: 480 VOLTS, 60 HERTZ, 40 AMPS, 3 PHASE, LAST RAN: SNACK FOOD (NUT MIX), POUCH SIZE: WIDTH: 5 INCHES DEPTH: 9 INCHES

PACE M500 STAINLESS STEEL AUTOMATIC BULK BOTTLE UNSCRAMBLER WITH INFEED HOPPER, SPEED: UP TO 300 BOTTLES PER MINUTE (DEPENDING ON PRODUCT SPECIFICATIONS), BOWL DIMENSIONS: DIAMETER: 60 INCHES DEPTH: 18 INCHES CAPACITY: 40 CUBIC FEET INFEED HEIGHT: 50 INCHES DISCHARGE WIDTH: 32 INCHES CONVEYOR DIMENSIONS: LENGTH: 70 INCHES WIDTH: 12 INCHES CLEAT CENTERS: 13 INCHES CLEAT HEIGHT: 2 INCHES INFEED HOPPER: DIMENSIONS: INCLINE LENGTH: 60 INCHES STRAIGHT TOP LENGTH: 30 INCHES WIDTH: 44 INCHES CONVEYOR: LENGTH: 70 INCHES WIDTH: 12 INCHES CLEATS: CENTERS: 13 INCHES HEIGHT: 2 INCHES DISCHARGE WIDTH: 33 INCHES ELECTRICAL: 220 VOLTS, 3 PHASE, 60 HZ

2016 SUN INDUSTRIES SBR-8V2016 8 STATION ROTARY STRETCH PAK SYSTEM - USED SUN INDUSTRIES ROTARY STRETCH PAK WITH: 8 STATIONS TOTAL PLATE DIMENSIONS: WIDTH: 16.5 INCHES LENGTH: 21.5 INCHES PLATES CURRENTLY SETUP FOR: (4) PIECES WIDTH: 2.75 INCHES ALUMINUM TABLE DIAMETER: 72 INCHES WORKING HEIGHT: 36 INCHES INFEED WIDTH: 14 INCHES DISCHARGE CONVEYOR: WIDTH: 20 INCHES LENGTH: 60 INCHES HEIGTH: 29 INCHES (ADJUSTABLE) PUSH BUTTON CONTROLS WITH DIGITAL SCREEN OVERALL FOOTPRINT: 15 X 12 FEET AIR REQUIREMENTS: 100 PSI AT 25 SCFM ELECTRICAL: 206/220 VOLTS, 3 PHASE, 50/60 HZ

KOSME ADHESIVE COMPACT 440 4T S2 E2 SELF ADHESIVE PRESSURE SENSITIVE ROTARY LABELER, PRODUCTION SPEED: UP TO 3000 BOTTLES PER HOUR, LABEL DIMENSIONS (INCHES): MAXIMUM LENGTH: 12.4 CORE DIAMETER: 3 MAX DIAMETER: 12, STYLE: ROTARY (3) STATIONS (5) HEADS COLD GLUE FRONT, BACK, NECK LABELING WORKING HEIGHT: 40 INCHES OVERALL DIMENSIONS (INCHES): LENGTH: 90 WIDTH: 95 HEIGHT: 81 PUSH BUTTON CONTROLS STAR WHEEL TIMING INFEED STAINLESS STEEL CONSTRUCTION MOUNTED ON SCREW LEVELING LEGS ELECTRICAL: 3 PHASE, 60 HERTZ, 230 VOLTS LAST APPLICATION: 12 OUNCE NECK BOTTLES WITH A LABEL DIMENSION OF 4 BY 3.5 AND 1.75 BY 1.25 AT A SPEED OF 3,000 BOTTLES PER HOUR

TEXWRAP 2201-SS CONTINUOUS MOTION SIDE SEALER WITH STAINLESS STEEL LUGGED INFEED. MAXIMUM PRODUCT DIMENSIONS: LENGTH: INFINITE WIDTH: 20 INCHES HEIGHT: 10 INCHES. MINIMUM PRODUCT DIMENSIONS: LENGTH: 4 INCHES WIDTH: 2 INCHES. SEAL BAR WIDTH: 24 INCHES. MAXIMUM FILM WIDTH: 32 INCHES. SELVAGE REWINDER. ELECTRICAL: 115 VOLTS, 60 HERTZ, 1 PHASE. LUGGED INFEED DIMENSIONS: LENGTH: 121.5 INCHES WIDTH: 18 INCHES (ADJUSTABLE). INFEED HEIGHT: 34 INCHES. STAINLESS STEEL CONSTRUCTION.

PALACE SFMPB-50 BOTTLE UNSCRAMBLER WITH HOPPER, DESIGNED TO AUTOMATICALLY ORIENT AND FEED BOTTLES INTO PRODUCTION LINES, IMPROVING OPERATIONAL EFFICIENCY. IT FEATURES A HIGH-CAPACITY HOPPER THAT CAN HANDLE LARGE VOLUMES OF BOTTLES, REDUCING THE NEED FOR MANUAL HANDLING. THE MACHINE ENSURES PRECISE BOTTLE PLACEMENT, MINIMIZING JAMS AND ENSURING SMOOTH FLOW. BUILT FOR DURABILITY AND EASY OPERATION, THE SFMPB-50 HELPS STREAMLINE BOTTLE HANDLING IN HIGH-SPEED PRODUCTION ENVIRONMENTS. OUTPUT: UP TO 120 CONTAINERS PER MINUTE DEPENDING ON BOTTLE SIZE. 50 INCH DIAMETER DISC. HOPPER SPECIFICATIONS: INFEED HEIGHT FROM GROUND: 47 INCHES. CLEATS: 7 INCHES WIDE X 4 INCHES TALL. BELT WIDTH: 11 INCHES. DISCHARGE HEIGHT FROM GROUND: 71 INCHES. OPERATOR CONTROLS WITH E-STOP. VARIABLE SPEED CONTROLS. STAINLESS STEEL CONSTRUCTION. LAST RUNNING 750 ML PET BOTTLES.

ALEPACK AP411S BATTERY PACKAGING LINE, LAST RAN PACK SIZE: LENGTH: 2.5 INCHES WIDTH: 1.75 INCHES INFEED DIMENSIONS (3) LANES: LENGTH: 27 INCHES WIDTH: 3 INCHES DISCHARGE CONVEYOR DIMENSIONS (3) LANES: LENGTH: 32 INCHES WIDTH: 2 INCHES ACCUMULATION TABLE DIMENSIONS: LENGTH: 32 INCHES WIDTH: 24 INCHES DUST COLLECTOR INCLUDES MULTIPLE INSERTS FOR DIFFERENT PACK SIZES TOUCH SCREEN CONTROLS STAINLESS STEEL FRAME AIR CONSUMPTION: 6 CUBIC FEET PER MINUTE AT 100 PSIG ELECTRICAL REQUIREMENTS: 230 VOLTS, 60 HERTZ, 3 PHASE OVERALL DIMENSIONS: LENGTH: 163 INCHES WIDTH: 33 INCHES HEIGHT: 100 INCHES LAST USED IN PACKAGING OF HEARING AID BATTERIES