MultiFacility CNC Fabrication Process Equipment

KUKA ROBOTIC WELDING CELL KUKA KR16 ARM W/KRC4 CONTROL PACKAGE FRONIUS TRANSPLUS SYNERGIC 5000 (460V) TWIN MIG CMT TORCH PACKAGE FRONIUS CU 1800 CHILLER FRONIUS FK4000-R & FK9000-R TORCH COOLERS I-KIT TWIN NETWORK INTERFACE ROBACTA REAMER TWIN W/WIRE CUTTER SERVO ROBOT SEAM TRACKING LJ WELDING P12PS-12,000 LB. POSITIONER ROBO VENT HVE-175 FILTRATION SYSTEM THE CELLS INTENDED DESIGN WAS FOR THE CREATION OF LARGE BEVEL FILLET WELD LEG GEOMETRIES UP TO 9MM (APPROXIMATELY 0.375 INCHES) AND DID SO WITH THE USE OF AN INTEGRATED INDEXABLE HORIZONTAL WELD MANIPULATOR THAT WOULD TURN AN APPROXIMATE 1000MM (~39.4 INCH) DIAMETER CYLINDER AND WOULD BE CIRCUMFERENTIALLY WELDED THROUGH THE USE OF A TWIN CMT WELD TORCH ATTACHED TO A KUKA KR16 OUTFITTED WITH LASER SEAM TRACKING AND SMOKE EXTRACTION. FOR THIS APPLICATION, TWIN 0.045 INCH DIAMETER FILLER WIRES ARE FED AT A SPEED OF 385 IPM TO ACHIEVE THE NEEDED RESULTING WELD GEOMETRY ACHIEVING A TOTAL WELD TIME OF APPROXIMATELY 6.5 MIN PER WELD PAIR. DURING THE WELD, THE LASER SEAM TRACKER WOULD ALLOW A LIVE FEEDBACK LOOP FROM WHICH THE WELDING ROBOT WOULD ADJUST FOR ANY DISCONTINUITIES. THE CELL HAS A TOTAL RUNNING TIME OF 1931.72 HRS AS REPORTED FROM THE KUKA CONTROLLER.

NEW/UNUSED FULLY AUTOMATIC TABLET PRESS MACHINE 225,000 TABLETS PER HOUR HMI TOUCHSCREEN TABLET DUST COLLECTOR UPHILL DEDUSTER VACUUM TO PULL POWDER INTO THE MACHINE ALL SENSORS, WIRING, ETC ARE INCLUDED WEIGHT: 1800 KG NEW, UNUSED CONDITION

2 AL8400 & AL8401 PINNACLE MIXING TANKS 5,600 GAL.; 2 MIXERS PER TANK. AL8400 - NEW CAPACITY: 5600 GALLONS (134 BBL) WALLS/ROOF: 1/4" A36 PLATE FLOOR: 1/4" A36 PLATE LONG SILL: 6X2X1/4" TUBING X-MEMBERS: CHANNEL 3 X 5.4 WHEELS: 8" STEEL LIFTING LUGS: 3/4" A36 PLATE MANWAYS: (1) - 36" (ROOF) WITH REMOVABLE FALL PROTECTION (1) - 22" (FRONT) VALVES: (1) - 4" DRAIN (FRONT) (1) - 4" DRAIN (REAR) BLIND FLANGE: (1) - 4" (REAR) (1) - 4" (ROOF) FILL LINE: (1) - 4" (REAR/TOP) P/V VALVE: (1) - 8" (ROOF) PORT: (2) - 1 1/2" MERCH (ROOF) (1) - SIGHT GLASS (FRONT) WELD: AWS D1.1 OSHA: 1910 SUBPART D BLAST: SSPC-SP-10 (INT.) (NEAR WHITE) PAINT: (INT.) EPOXYPHENOLIC 100% SOLID 20.0 MILS D.F.T. 119640 PAINT-NTEBLUEG140 8845 - BLUE # G140 SSPC-SP-6 (EXT.) (COMMERCIAL BLAST) (EXT.) FINISH COAT POLYURETHANE 4.0 TO 5.0 D.F.T. MFG SERIAL NO. AL8400/AL130-MX. AL8401 - USED LESS THAT 5 TIMES CAPACITY: 5600 GALLONS (134 BBL) WALLS/ROOF: 1/4" A36 PLATE FLOOR: 1/4" A36 PLATE LONG SILL: 6X2X1/4" TUBING X-MEMBERS: CHANNEL 3 X 5.4 WHEELS: 8" STEEL LIFTING LUGS: 3/4" A36 PLATE MANWAYS: (1) - 36" (ROOF) WITH REMOVABLE FALL PROTECTION (1) - 22" (FRONT) VALVES: (1) - 4" DRAIN (FRONT) (1) - 4" DRAIN (REAR) BLIND FLANGE: (1) - 4" (REAR) (1) - 4" (ROOF) FILL LINE: (1) - 4" (REAR/TOP) P/V VALVE: (1) - 8" (ROOF) PORT: (2) - 1 1/2" MERCH (ROOF) (1) - SIGHT GLASS (FRONT) WELD: AWS D1.1 OSHA: 1910 SUBPART D BLAST: SSPC-SP-10 (INT.) (NEAR WHITE) PAINT: (INT.) EPOXYPHENOLIC 100% SOLID 20.0 MILS D.F.T. 119640 PAINT-NTEBLUEG140 8845 - BLUE # G140 SSPC-SP-6 (EXT.) (COMMERCIAL BLAST) (EXT.) FINISH COAT POLYURETHANE 4.0 TO 5.0 D.F.T. MFG SERIAL NO. AL8401/AL130MX.

NEW/UNUSED 48 CHANNEL COUNTER FULLY AUTOMATIC ACCURATELY COUNTS TABLETS, CAPSULES, SOFT GELS, GUMMIES 2 LANE CONVEYOR SYSTEM ATTACHED WITH COUNTER - FULLY AUTOMATIC - ALL SENSORS, WIRING, ETC ARE INCLUDED 4 BOTTLE COUNTING NOZZLES TO FILL BOTTLES AT THE SAME TIME - COUNTS 100+ BOTTLES PER MINUTE BASED ON THE BOTTLE SIZE - CANNISTER/DESICCANT MACHINE FULL BOTTLE FILLING LINE CAPABILITY SIEMENS HMI TOUCHSCREEN

MINSTER P2-100-60 PIECE-MAKER 100 TON FLYWHEEL STRAIGHT SIDE PRESS. MANUFACTURER: THE MINSTER MACHINE COMPANY SERIES: P2-100-60 PIECE-MAKER TYPE: FLYWHEEL STRAIGHT SIDE / PIECE-MAKER TONNAGE RATING: 100 TONS BOLSTER SIZE (L.R. X F.B.): 60" X 31" STROKES PER MINUTE: 80 - 160 SPM STROKE OF SLIDE: 4" MAXIMUM ADJUSTMENT OF SLIDE: 4" SHUTHEIGHT TO BOLSTER: 15" SHUTHEIGHT TO BED: 20" SLIDE ADJUSTMENT RANGE: 11.000" TO 15.000" DIE CUSHION: 1 CUSHION (1 BED OPENING) CUSHION CYLINDER DIAMETER: 12" CUSHION TRAVEL: 2.9" TONS FORCE ON CUSHION (WITH 10 PSI AIR): 7.56 TONS COUNTERBALANCE CYLINDER EFFECTIVE AREA: 97 SQ. IN. CLUTCH AIR PRESSURE: 60 LBS. MAIN ELECTRIC POWER SUPPLY: 480 V / 3 PH / 60 HZ CLUTCH CONTROL VOLTAGE: 110 V / 1 PH / 60 HZ DRIVE MOTOR FULL LOAD CURRENT: 26 A CLUTCH CONTROL FULL LOAD CURRENT: 16 A CONTROL TRANSFORMER CAPACITY: 1,500 VA CONTROL VOLTAGE: 120 V CONTROL DIAGRAM: V-AMH-62-216 A CLUTCH SERIES/TYPE: CRANKSHAFT LOCATION / 28-CFC (0.070" LEFT/RIGHT SIDE SHRINKAGE) TIE ROD HEATER SIZE: 480 V - 4002 W - 1900 W LUBRICATION SYSTEM: MONITORFLOW CONTINUOUS PRESSURE RE-CIRCULATING SYSTEM EQUIPPED WITH: LITTELL STRAIGHTENER / FEEDER UNIT MACHINE ASSEMBLY (SN: 78982-4-73) WELDOTRON SAFE-T-LITE SAFETY LIGHT CURTAIN SYSTEM CONTROLS (MODEL: 2216 / SN: VC02412 & NC41682) MINSTER CLUTCH CONTROL ENCLOSURE STATION PANEL SYSTEM (SERIAL NO. 25467) STAND-ALONE OPERATOR COMMAND CONSOLE ENCLOSURE WITH RUN/JOG CONTROLS ORIGINAL MINSTER PRESSES SERVICE & OPERATING MANUAL DOCUMENTATION PACK S/N: P2-100-21757

MORI SEIKI NL2500MC 3-AXIS CNC LATHE - MORI SEIKI NL2500MC 3-AXIS CNC TURNING CENTER SWING OVER BED 36.4" (923.8 MM) MAX TURNING DIAMETER 14.4" (366 MM) MAX TURNING LENGTH 49.4" TO 51" (12551298 MM) BAR CAPACITY 3.15" (80 MM) AXIS TRAVEL (X / Z) X: 10.2" (260 MM) / Z: 52.9" (1345 MM) MAIN SPINDLE SPEED UP TO 4,000 RPM SPINDLE NOSE / BORE JIS A2-8 / 3.58" (91 MM) LIVE TOOLING SPEED UP TO 6,000 RPM TURRET CAPACITY 12 STATIONS ELECTRICAL POWER 220V, 3-PHASE, 60 HZ MACHINE WEIGHT APPROX. 16,000 TO 16,500 LBS (~7,300 KG) S/N: NL251F12356

BROOMFIELD LABORATORIES SERIES 500C COIL WINDER WITH RANGER TRAVERSE (NEW)

2000 ARBURG ALLROUNDER 630 INJECTION MOLDING MACHINE BARREL SIZES 1ST SHOT 45MM 2ND SHOT 30 MM 90 DEG TO PLATEN NO ROTARY PLATEN HOURS 53500 ARBURG ROBOT INCLUDED

2004 30 KILO TOPER TKM S30 COFFEE ROASTER - DIGITAL CONTROLS & CUSTOM CHAFF COLLECTOR. 30 KILO COFFEE ROASTER COMES WITH CUSTOM DIGITAL CONTROLS AND A CUSTOM CHAFF COLLECTOR. THE DIGITAL CONTROLS DONT JUST LOG THE ROASTS, THEY AUTOMATE THEM.

CINCINNATI 90CB BY 8' PRESS BRAKE - HAS NEW TOLEDO CONTROLS (8 YEARS OLD)

2023 KEY TECHNOLOGIES PULSESCRUBBER CONTINUOUS POLISHER STAINLESS STEEL FOOD EQUIPMENT WITH VACUMAX PNEUMATIC CONVEYOR CONTINUOUS ROTARY POLISHER / SCRUBBER FOOD-GRADE STAINLESS STEEL CONTINUOUS, FULLY AUTOMATIC POTATOES, CARROTS, BEETS, NUTS, ROOT VEGETABLES, SIMILAR PRODUCE THROUGHPUT CAPACITY APPROX. 10,000-30,000 LBS/HR ELECTRIC MOTOR WITH VARIABLE SPEED CONTROL GENTLE MECHANICAL AGITATION WITH ADJUSTABLE PULSE FREQUENCY CYLINDRICAL STAINLESS DRUM WITH INTERNAL PADDLES OR BRUSH SYSTEM GRAVITY OR CONVEYOR FEED TO DOWNSTREAM PROCESS QUICK-RELEASE COVERS, WASHDOWN-READY DESIGN, DRAIN PORTS DIMENSIONS ~120 L X 48 W X 60 H WEIGHT APPROX. 2,000-3,000 LBS ELECTRICAL 460V / 3-PHASE / 60HZ

CHECK WEIGHER / METAL DETECTOR SYSTEM; FORTRESS STEALTH METAL DETECTOR 8X8 ACCURATE SUPERIOR CHECKWEIGHER (RICE LAKE SCALE CONTROLS) SYSTEM INTEGRATION AND CONVEYANCE BY D&R PACKAGING 120 VAC 1PH 20 AMP COMPRESSED AIR, 80 PSI @ 5 CFM

1 AL470-MX4 PINNACLE MIXING TANK 17,630 GAL.; 4 MIXERS 219110-M AL470-MX4 STANDARD MSTR AL470-MX4 4 MIXERS TARE: 32,000 LBS. 420 BBL (17,630 GAL.) VAPOR TIGHT PINNACLE QUALITY ASSURANCE INSPECTIONS FULL HYDROSTATIC WATER TEST WALLS: 1/4" A36 PLATE FLOOR: 1/4" A36 PLATE RECESSED SIDE STAIRWAY FOLDING HANDRAILS SUSPENSION: 22,500 LBS. CAPACITY MANWAYS: 2 - 22" WITH BUNA GASKETS 2 - 36" WITH BUNA GASKETS PRESSURE VACUUM VALVE: 16OZ PRESSURE .4OZ VACUUM DRAINS: 2 - 4" BUTTERFLY VALVE FLANGES: 1 - 4" BLINDED FILL LINE: 3" NIPPLE AND CAP COIL: 1-2 SCH 80 PIPE COIL ASSEMBLY NEMA 7/9 RATED CONTROL BOX WITH 70A MAIN BREAKER 4 IMPELLER GEAR BOXES WITH 10 HP 480V 3 PH MOTORS INTERIOR BLAST: SSPC-SP10 NEAR WHITE EXTERIOR BLAST: SSPC-SP-6 COMMERCIAL LINER: CARBOLINE 310 (20 - 25 MILS) TOP COAT: POLYURETHANE 4 - 6 MILS UNDERCOAT 119640 PAINT-NTEBLUEG140 8845 - COLOR BLUE # G140 (EACH 5 GALLON KIT CONSISTS OF 4 GALLONS PART A IN 5 GALLON PAIL & 1 GALLON PART B IN 1 GALLON PAIL)

CUSTOM INDUSTRIAL PILOT-LINE CHEMICAL VAPOR DEPOSITION (CVD) SYSTEM PRIMARY APPLICATION: HIGH-TEMPERATURE GAS-PHASE SYNTHESIS, COATING OF BATTERY ELECTRODE MATERIALS, OR CARBON NANOMATERIAL GROWTH (CNTS/GRAPHENE) ENCLOSURE TYPE: MODULAR HEAVY-DUTY STEEL FRAME WITH BLUE POWDER-COATED ACCESS PANELS AND INTEGRATED EXHAUST VENTILATION HOODS THERMAL ZONES: MULTI-ZONE HIGH-TEMPERATURE FURNACE (CONTROLLED VIA LOWER RACK-MOUNTED TEMPERATURE CONTROLLERS) VACUUM SYSTEM: INTEGRATED LOWER CABINET HOUSING DUAL BACKING PUMPS (ROTARY VANE / DRY BOOSTER PUMPS) CONNECTED VIA STAINLESS STEEL VACUUM LINES

2007 DOOSAN PUMA MX2000ST MULTI AXIS LATHE - LIVE TOOLING, SUB SPINDLE. SWING OVER BED: 29.52 INCH SWING OVER SADDLE: 23.62 INCH RECOMMENDED TURNING DIAMETER: 8.26 INCH MAX TURNING DIAMETER: 21.65 INCH MAX WORKING LENGTH: 40.15 INCH BAR WORKING DIAMETER: 2.55 INCH MAIN SPINDLE: CHUCK SIZE: 8 INCH SPINDLE NOSE: A2-6 SPINDLE DIAMETER: 4.33 INCH SPINDLE THROUGH HOLE: 2.99 INCH BORE OF DRAW TUBE: 2.59 INCH MAIN SPINDLE MOTOR: 29.5 HP/ 20 HP MAX SPINDLE SPEED: 5,000 RPM MAX SPINDLE INDEXING (C AXIS): 0.001 DEGREES. MILLING SPINDLE: SPINDLE TAPER: CAPTO C6 MILLING SPINDLE DIAMETER: 2.75 INCH SPINDLE MOTOR: 20 HP / 15 HP MAX MILLING SPINDLE SPEED: 10,000 RPM INDEX OF MILLING SPINDLE: 360 DEGREES IN 30-DEGREE INCREMENTS. TOOL CHANGER CAPACITY: 24 TOOL CHANGER ARM: SWING ARM TOOL CHANGE TIME: 1.5 SEC. CARRIAGE: X1 AXIS TRAVEL: 21.85 INCH X2 AXIS TRAVEL: 7.28 INCH Z1 AXIS TRAVEL: 43.11 INCH Z2 AXIS TRAVEL: 44.88 INCH Y AXIS TRAVEL: 6.29 INCH (3.14 INCH) A-AXIS TRAVEL: 41.92 INCH C1, C2 AXIS TRAVEL: 360 (0.001) DEGREE B-AXIS: 240 DEGREE (120) B AXIS COUPLING CLAMP DEGREE: 15 INCH. BED & SADDLE SLANT ANGLE: 45 DEGREES BED (Z1 AXIS): 21.25 INCH SADDLE (X1 AXIS): 11.22 INCH SADDLE (X2 AXIS): 9.44 INCH RIGHT SPINDLE BASE: 17.51 INCH. LOWER TOOL POST: NUMBER OF TOOL STATIONS: 12 BORING BAR SIZE: 1.57 INCH ROTARY TOOL SPEED: 4,000 RPM ROTARY TOOL MOTOR: 7.5 HP. MACHINE WEIGHT: 12,500 KG (27,557 LBS) MACHINE FLOOR DIMENSIONS: 177.95 X 98.22 X 102.36 INCH. EQUIPPED WITH: FANUC 18I-TB CONTROL CHIP CONVEYOR SUB SPINDLE B AXIS Y AXIS C AXIS LIVE TOOLING.

1 FMX25 FLASHMIX MIXER SILVERSON FLASHMIX MIXER MODEL: FMX25 FLASHMIX MIXER PRODUCT CONTACT PARTS: 316L STAINLESS STEEL MOTOR: 7.5HP, 230V/3PH/60HZ EXPLOSION PROOF (CLASS 1/DIV 1/GROUP D) INVERTER DUTY SEAL: SINGLE TUNGSTEN CARBIDE/SILICON CARBIDE/VITON SEAL ELASTOMERS: VITON WORKHEAD: GENERAL PURPOSE DISINTEGRATING HEAD (GPDH) ROTOR: 4-BLADED O-RINGS: VITON NECK SECTION: STAINLESS STEEL CONNECTIONS: TRICLAMP INLET: 2.5 OUTLET: 2.5 TANGENTIAL SELF DRAINING PRESSURES: MAX 150PSI INLET MANIFOLD (1) MACHINE FMX25/0341 (2) MACHINE FMX25/0342 (1) MOTOR SERIAL F2211075633 (2) MOTOR SERIAL F2211075636 HOPPER 1.5TRI-CLAMP- FMX25, FMX30 (1) HOPPER 47965-4 (2) HOPPER 47965-5 SACK TABLE ASSEMBLY FOR FMX25 (1) SACK TABLE 46693 (2) SACK TABLE 42470-2 VARIABLE FREQUENCY DRIVE AC TECH 7.5HP, 230V INPUT / OUTPUT NEMA 4X (1) VFD 4 734-2 (2) VFD 4 734-3 IOM / SAFETY MANUAL INCLUDED IOM / SAFETY MANUAL INCLUDED 1.5 BALL VALVE, 2-WAY O-RING KIT VITON -275UHS-HV FACE KIT BF-035-Z85-16263- 0 FACEKIT SIC TC FPM (VITON)FDA

1 FMX25 FLASHMIX MIXER PRODUCT CONTACT PARTS: 316L STAINLESS STEEL MOTOR: 7.5HP, 230V/3PH/60HZ EXPLOSION PROOF (CLASS 1/DIV 1/GROUP D) INVERTER DUTY SEAL: SINGLE TUNGSTEN CARBIDE/SILICON CARBIDE/VITON SEAL ELASTOMERS: VITON WORKHEAD: GENERAL PURPOSE DISINTEGRATING HEAD (GPDH) ROTOR: 4-BLADED O-RINGS: VITON NECK SECTION: STAINLESS STEEL CONNECTIONS: TRICLAMP INLET: 2.5 OUTLET: 2.5 TANGENTIAL SELF DRAINING PRESSURES: MAX 150PSI INLET MANIFOLD (1) MACHINE FMX25/0341 (2) MACHINE FMX25/0342 (1) MOTOR SERIAL F2211075633 (2) MOTOR SERIAL F2211075636 HOPPER 1.5TRI-CLAMP- FMX25, FMX30 (1) HOPPER 47965-4 (2) HOPPER 47965-5 SACK TABLE ASSEMBLY FOR FMX25 (1) SACK TABLE 46693 (2) SACK TABLE 42470-2 VARIABLE FREQUENCY DRIVE AC TECH 7.5HP, 230V INPUT / OUTPUT NEMA 4X (1) VFD 4 734-2 (2) VFD 4 734-3 IOM / SAFETY MANUAL INCLUDED 1.5 BALL VALVE, 2-WAY O-RING KIT VITON -275UHS-HV FACE KIT BF-035-Z85-16263- 0 FACEKIT SIC TC FPM (VITON)FDA

2010 FLOW WATER JET WITH 60,000 PSI INTENSIFIER PUMP, 10 FOOT BY 6.5 FOOT WORK AREA TABLE. INCLUDES GARNET, SPARE PARTS, TOOLS, SONIC CLEANER, PARTS WASHER, ELECTRICAL BOX AND OTHER MISC ITEMS. VERY LOW HOURS. THE WATER JET HAS BEEN RECENTLY SERVICED AND IS READY TO RUN.

GRIEVE WTC686-500 INDUSTRIAL ELECTRIC OVEN INTERIOR CHAMBER DIMENSIONS: 72" W X 96" D X 78" H BLOWER / AIR RECIRCULATION: ~6,000 CFM POWERED BY 5 HP MOTOR AIRFLOW PATTERN: COMBINATION HORIZONTAL/VERTICAL AIRFLOW HEATING ELEMENTS: INCOLOY ALLOY-SHEATHED TUBULAR HEATING ELEMENTS ESTIMATED WEIGHT: ~6,500 LBS

2016 DALLAS INDUSTRIES DPR-6,000# X 18 MOTORIZED CENTERING REEL & HOLD DOWN ARM. REEL MODEL: DPR-6,000# X 18 REEL SN: 22089 HOLD DOWN MODEL: CR-6,000# X 18 HOLD DOWN SN: 22090 MAXIMUM COIL WEIGHT CAPACITY: 6,000 LBS. MAXIMUM COIL WIDTH CAPACITY: 18" COIL I.D. RANGE: 16" - 21" MAXIMUM COIL O.D.: 60" (HOLD DOWN ACCOMMODATES 22" O.D. MIN / 60" O.D. MAX) REEL DRIVE: 2 H.P. AC VARIABLE FREQUENCY DRIVE PAYOUT RATE: 4 TO 16 R.P.M. EQUIPPED WITH: AIR-OPERATED NON-MOTORIZED COIL HOLD DOWN ARM LOOP CONTROL ARM MANUAL MANDREL EXPANSION VIA SNAP-OUT CRANK SIX 60" OD COIL KEEPERS. S/N: 22089 / 22090

CLAMCO R785 ROLLBAG SEALER - OPERATION: FOOTSWITCH, MANUAL, OR AUTO CYCLE MODE - SPEED: UP TO 40 BAGS/MIN (UP TO 30 BAGS/MIN WITH LABEL PRINTER APPLICATOR) - BAG DIMENSIONS: 2" - 12" WIDTH; 3" - 20" LENGTH - BAG GAUGE: 1-4 MIL (10" MAX ROLL DIAMETER) - SEAL WIDTH: 1/8" - SEAL BAR OPENING: 4" - DIMENSIONS: 26" W X 18" D X 24" H (24 D WITH LABEL PRINTER APPLICATOR) - WEIGHT: 105 LBS - ELECTRICAL: 120V, 5A

2018 AP SN2816 LASER ENGRAVER. WORKSPACE: 28" X 16". MATERIAL PROCESSING AREA: 448 SQ. IN. MACHINE FOOTPRINT: 7' X 5'. CONNECTION TO COMPUTER: USB. CO2 POWER: 100W UPGRADE. POWER CONSUMPTION: 900W. ELECTRICAL REQUIREMENTS: 110V. RATED FREQUENCY: 60HZ. RATED POWER: 1.15KW. ENGRAVING SPEED: 0-50"/S. LASER TUBE LIFE: 8,000 HRS. EXHAUST SIZE: 6". NET WEIGHT: 575 LBS. EQUIPPED WITH 100W LASER TUBE.

2022 NEPTUNE ECOBAGGER 2100 PREMADE POUCH BAGGER - ORIGINAL PACKAGING, UNOPENED PRODUCTION OUTPUT RATE: UP TO 20 BAGS PER MINUTE, DEPENDING ON APPLICATION AND PRODUCT VARIETY OF BAG STYLES: 3 OR 4 SIDE SEALED PILLOW POUCHES STAND UP BAGS / DOY PACK GUSSETED POUCHES QUAD SEALED BOX POUCH BAGS WITH OR WITHOUT ZIPPER 25% HEAD SPACE IS REQUIRED MINIMUM BAG WIDTH: 3.93 INCHES / 100 MILLIMETERS MAXIMUM BAG WIDTH: 8.26 INCHES / 210 MILLIMETERS STAINLESS STEEL CONSTRUCTION LCD TOUCH CONTROL OPERATING SYSTEM PRODUCT OUTPUT CONVEYOR ELECTRICALS: 220 VOLTAGE / 1 PHASE ZIPPER OPENER EXIT CHUTE ELITE NET LINEAR WEIGHT - 2 LANE DIMPLED SCALE PLATFORM FLOOR STAND FOR SCALE VIDEOJET INKJET 1280 PRINTER

2016 DALLAS INDUSTRIES DPR-6,000# X 18 MOTORIZED CENTERING REEL & HOLD DOWN ARM. REEL MODEL: DPR-6,000# X 18 REEL SN: 23459 HOLD DOWN MODEL: CR-6,000# X 18 HOLD DOWN SN: 23460. MAXIMUM COIL WEIGHT CAPACITY: 6,000 LBS. MAXIMUM COIL WIDTH CAPACITY: 18" COIL I.D. RANGE: 16" - 21" MAXIMUM COIL O.D.: 60" (HOLD DOWN ACCOMMODATES 22" - 60" O.D.). REEL DRIVE: 2 H.P. AC VARIABLE FREQUENCY DRIVE PAYOUT RATE: 4 TO 16 R.P.M. EQUIPPED WITH: AIR-OPERATED NON-MOTORIZED COIL HOLD DOWN ARM AUTOMATION DIRECT US DRIVE (3 HP, 480 VAC, MODEL: GS2-43P0) LOOP CONTROL ARM MANUAL MANDREL EXPANSION VIA SNAP-OUT CRANK SIX 60" OD COIL KEEPERS

1996 138 TON X 13' AMADA HFB 125-40 CNC PRESS BRAKE - 6 AXIS BACKGAUGE CAPACITY: 138 TONS STROKE: 7 BED LENGTH: 13' THROAT: 16.1 OPEN HEIGHT: 17.7" BETWEEN COLUMNS: 12' 4 AUTOMATIC BACKGAUGE CAPACITY: 28 8-AXIS: PASSIVE & ACTIVE NUMBER OF FINGERS: 8 APPROACH SPEED: 236 IPM BENDING SPEED: 19 IPM RETURN SPEED: 189 IPM MACHINE DIMENSIONS (APPROX.): 138 X 92 X 105 MACHINE WEIGHT (APPROX): 22,000 LBS EQUIPPED WITH: 14 AMADA ONE TOUCH TOOL HOLDERS OPERATUER CNC CONTROL

2007 KOMO FUSION 524 VR BRIDGE STYLE CNC ROUTER TABLE SIZE: 5 X 24 (60 X 288) VACUUM TABLE. AXIS TRAVEL: X-AXIS: 288 (MOVING TABLE) Y-AXIS: 60 (GANTRY CROSS TRAVEL) Z-AXIS: 12 (SPINDLE VERTICAL TRAVEL) SPINDLE: 24,000 HORSEPOWER: 14 HP SPEED: 24,000 RPM TAPER: HSK 63F TYPE: FAN-COOLED, 4-POLE AUTOMATIC TOOL CHANGER: 15 POSITION CAROUSEL CONTROL SYSTEM: KOMO-GE FANUC I CNC CONTROL AXIS DRIVES: DIGITAL FANUC ALPHA HVI SERVO MOTORS ON ALL AXES, WITH A PRE-LOADED PRECISION BALL SCREW SYSTEM FOR Y AND Z AXES, AND A RACK AND PINION OR BALL SCREW SYSTEM FOR THE X-AXIS. CONSTRUCTION: HEAVY-DUTY STEEL FABRICATION WITH A FEA ENGINEERED STRUCTURE. OVERALL MACHINE DIMENSIONS: APPROXIMATELY 299 (L) X 86 (W) X 10 (H) WEIGHT: APPROXIMATELY 25,000 LBS (11,340 KG) ELECTRICAL: 480 VOLTS, 3 PHASE, 60 HZ EQUIPPED WITH: KOMO-GE FANUC I CNC CONTROL, MANUAL ROLLER-BALL TYPE TRANSFER TABLES WITH PNEUMATIC POSITIONING LOCKS PORTABLE PEDESTAL TYPE CONTROL STAND WITH HAND PENDANT, KOOLANT KOOLERS DIMPLEX THERMAL SOLUTIONS MODEL JT750 SPINDLE OIL CHILLER DUST COLLECTION SYSTEM WITH CYCLONE RECEIVER & DUST FILTER BAGS

WEST BEND EQUIPMENT WELD-BILT 10,000 LBS. CAPACITY UPENDER LIFT TRUCK. MANUFACTURER: WEST BEND EQUIPMENT CORP. MODEL NUMBER: 48-48-48 WEIGHT CAPACITY: 10,000 LBS. EQUIPMENT TYPE: MECHANICAL COIL/DIE UPENDER INVERTER HYDRAULIC LIFT TRUCK PLATFORM DRIVE MOTOR MANUFACTURER: RELIANCE ELECTRIC COMPANY DRIVE MOTOR MODEL: DUTY MASTER / IDENT NO. F52 MOTOR SPECIFICATIONS: 230V / 38 AMPS / 1 PHASE / 60 HZ TORQUE OUTPUT: 10 FT. LBS. S/N: CR-2054

PARLEC PARSETTER TMM TOOL PRESETTER WITH SHRINK SET

1 ZEFIRO EVAP 560 PN DELFIN INDUSTRIAL VACUUM 5HP, THREE-PHASE, 460V 60HZ, ZONE 22, 6.4HP, 26-GALON CAPACITY, 150MM (6IN.) INLET, POLYESTER ANTISTATIC CLASS M CARTRIDGE FILTER, AUTOMATIC PNEUMATIC FILTER CLEANING SYSTEM H H14 HEPA FILTER L=3 D. 150 - 10 FT. SUCTION ARM

1985 90 TON X 11' PACIFIC J13514/10 HYDRAULIC PRESS BRAKE - 3/16" CAPACITY, 208V. MANUFACTURER: PACIFIC MACHINE TYPE: HYDRAULIC PRESS BRAKE MODEL: J13514/10 TONNAGE: 90 TON PUNCHING CAPACITY CAPACITY: 3/16" MILD STEEL PLATE X 14'0" LONG MAXIMUM RAM/DIE WEIGHT: 0.35 TONS (APPROX. 700 LB ON THE RAM) HYDRAULIC RELIEF SETTING: 2,825 PSI ELECTRICAL SUPPLY: 208 VOLTS, 3PHASE, 60 HZ FULLLOAD CURRENT: 74.8 AMPS (125AMP CIRCUIT RATING) INTERRUPTING CAPACITY: 25,000 AMPS CONTROL POWER: 115 VOLTS, 1PHASE, 500 VA

MILLTRONICS ML26 CNC LATHE - MILLTRONICS ML26 CNC TURNING CENTER CAPACITY & WORKING ENVELOPE SWING OVER BED: 27" (685 MM) SWING OVER CROSS SLIDE: 16.1" (410 MM) SWING OVER GAP (IF EQUIPPED): 34.2" (870 MM) DISTANCE BETWEEN CENTERS / BED LENGTHS: 40", 80", 120", OR 160" MAIN SPINDLE SPINDLE MOTOR: 24 HP (18 KW) SPINDLE SPEED RANGE: 30 - 1,600 RPM (UP TO 2,000 RPM ON ML26/40) SPINDLE BORE: 3.22" (STANDARD) OR 4.17" / 6.02" OPTIONAL BIG BORE SPINDLE NOSE: A1-8 (A1-11 FOR BIG BORE OPTIONS) MAX SPINDLE TORQUE: UP TO 1,250 FT-LBS (1,695 NM) TURRET & TOOLING TOOL POST / TURRET TYPE: STANDARD 8-STATION AUTOMATIC ELECTRO-MECHANICAL TURRET OR 4-WAY AUTO TOOL POST SHANK TOOLING SIZE: 1" (25 MM) MAX BORING BAR SIZE: 1.5" (38 MM) MOTION & FEED RATES X-AXIS TRAVEL: 13" (330 MM) Z-AXIS TRAVEL: VARIES BY BED LENGTH (42" TO 160") RAPID TRAVERSE RATE (X / Z): 500 IPM (12.7 M/MIN)

NOVEXX LABELER SYSTEM - STAINLESS STEEL FRONT / BACK / TOP TRIPLE LABEL APPLICATION SYSTEM WITH LID SEATING TAMP; (3) NOVEXX 4" WIDTH CAPACITY LABEL DISPENSING HEADS; ALLEN BRADLEY PLC AND 7" COLOR TOUCH SCREEN OPERATOR INTERFACE PANEL FOR SYSTEM STAINLESS STEEL FRAME AND CONVEYOR COMPONENTS SIDE GRIP TRANSFER / ALIGNMENT HUGGER BELTS TOP LABELING AND LID SEATING WILL BE DONE WITH A SINGLE TAMP APPLICATION SYSTEM TOP HOLD DOWN BELT TO INSURE PRODUCT ALIGNMENT AS THE FRONT AND BACK LABELS ARE APPLIED SHAFT MOUNTED GEAR MOTORS REMOTE LABEL HEAD CONTROLS FOR THE BACK SIDE LABELING HEAD 240 VAC 1PH 20 AMP COMPRESSED AIR, 80 PSI @ 5 CFM

MARBURG SHRINK SEAL SYSTEM TAMPER SLEEVE APPLICATOR WITH CONVEYOR AND HEAT SHRINK TUNNEL; MARBURG 1250 DELI BANDER WITH OPTIONAL VERTICAL PERFORATION MARBURG CONVECTION HEAT SHRINK TUNNEL WITH OPTIONAL AUTO LIFT STAINLESS STEEL CONVEYOR INTEGRATION OF COMPONENTS AND ASSEMBLY SLEEVE APPLICATOR: 120 VAC 1PH 20 AMP SHRINK TUNNEL: 240 VAC 1 PH 30 AMP COMPRESSED AIR, 80 PSI @ 15 CFM

1999 CMS PG5 5 AXIS CNC VERTICAL CNC CENTER WITH OSAI CMS CONTROLLER - PXS 4204. X/Y TRAVEL: 120 INCHES, Z TRAVEL: 24 INCHES. FEED RATE: 120 INCHES PER MINUTE IN X&Y, 24 INCHES PER MINUTE IN Z. SPINDLE SPEED: 24000 RPM. TAPER: ISO40. S/N B391, CONTROLLER S/N 984403.

MAZAK QUICK TURN NEXUS 250-II M CNC TURNING CENTER STANDARD CHUCK SIZE: 10 INCHES MAXIMUM SWING: 26.5 INCHES (675 MM) MAXIMUM MACHINING DIAMETER: 14.75 INCHES (380 MM) MAXIMUM MACHINING LENGTH: 20 INCHES OR 40 INCHES (500U OR 1000U BED LENGTH OPTION) BAR WORK CAPACITY: 3.0 INCHES (77 MM) MAIN SPINDLE & C-AXIS SPINDLE SPEED RANGE: 35 - 4,000 RPM MAIN SPINDLE MOTOR: 35 HP (26 KW) SPINDLE BORE: 3.46 INCHES (88 MM) C-AXIS INDEXING: 0.001 FULL CONTOURING MILLING CAPABILITY & TURRET TURRET TYPE: 12-POSITION DRUM TURRET ROTARY TOOL DRIVE MOTOR: 7.5 HP (5.5 KW) ROTARY TOOL MAX SPEED: 4,500 RPM TOOL TYPE: MAZAK VDI / BOLT-ON STYLE AXIS TRAVEL & FEED RATES X-AXIS TRAVEL: 9.0 INCHES (230 MM) Z-AXIS TRAVEL: 22.6 INCHES (500U MODEL) OR 43.1 INCHES (1000U MODEL) RAPID TRAVERSE RATES (X / Z): 1,181 IPM / 1,299 IPM (30 M/MIN / 33 M/MIN)

SERIES 5 CINCINNATI PRESS BRAKE 10', 90 TON, 3" - MECHANICAL S/N: 46761

SERIES 5 CINCINNATI PRESS BRAKE 10', 90 TON, 3"- MECHANICAL SN: 47106

2016 JUNGHEINRICH EKS 308 ORDER PICKER S/N FN522631 (36 VOLT) YEAR OF MANUFACTURE: 2016 MODEL/OPTION: EKS 308, Z+I 105 550 ZT MANUFACTURER: JUNGHEINRICH AG, 22039 HAMBURG, GERMANY MADE IN GERMANY CAPACITY RATED CAPACITY: 1000 KG / 2205 LBS LOAD CENTER DISTANCE: 610 MM / 24 IN RESIDUAL LIFT CAPACITY: 1000 KG / 2200 LBS CAPACITY DE-RATE BY LIFT HEIGHT: LIFT HEIGHT: 24 IN 28 IN 31 IN CAPACITY: 2200 LB 1910 LB 1670 LB (REDUCE TRUCK CAPACITY BY ANY OPERATOR WEIGHT OVER 100 KG / 220 LB) LIFT / MAST MAX. LIFT HEIGHT: 6310 MM / 248 IN HOISTING SPEED (LOADED): 0.31 M/S HOISTING SPEED (UNLOADED): 0.39 M/S WEIGHTS WEIGHT OF TRUCK (NO BATTERY, 5%): 2704 KG / 5962 LBS APPROX. TOTAL SERVICE WEIGHT: ~3.75 T (WITH BATTERY) BATTERY WEIGHT, MIN: 927 KG / 2044 LBS BATTERY WEIGHT, MAX: 1025 KG / 2260 LBS ELECTRICAL / BATTERY SYSTEM VOLTAGE: 36 V MAX. BATTERY CAPACITY: 840 AH BATTERY ID: EO DISCHARGE (HOUR RATE): 6 H NOMINAL DRIVE POWER: 6.9 KW HOIST MOTOR POWER: ~7.5 KW PERFORMANCE TRAVEL SPEED (LOADED/UNLOADED): 11.5 KM/H (~7.1 MPH) DIMENSIONS (GENERAL EKS 308 36V PLATFORM) WHEELBASE: 1.69 M / 67 IN TRANSPORT LENGTH: 3.275 M / ~129 IN TRANSPORT WIDTH: 1.0 M / ~39 IN TRANSPORT HEIGHT: 2.32 M / ~91 IN WORKING AISLE WIDTH: 1.22 M / ~48 IN ADDITIONAL NOTES: LOW HOURS, ORIGINALLY BOUGHT FOR WAREHOUSE RACKING WELL-MAINTAINED BUT HAVE BEEN IN STORAGE IN THE WAREHOUSE FOR A FEW YEARS, NOT SURE ON BATTERY LIFE EACH MACHINE COMES WITH ITS OWN CHARGER AND SET OF FORKS

2020 SONICS & MATERIALS X-PRESS XPE2200-5 ULTRASONIC WELDER. 2200 WATTS. DIGITAL TIME AND/OR CONSTANT ENERGY WELD MODES AVAILABLE. SINGLE-PIECE RIGID CAST ALUMINUM MACHINE BASE AND COLUMN HUB. DIGITAL AMPLITUDE CONTROL. ULTRASONIC HORN/STACK FREQUENCY DISPLAY. FRONT PANEL PNEUMATIC SPEED AND PRESSURE MICROPROCESSOR WITH FRONT PANEL KEYPAD. STROKE AIR CYLINDER: 4 INCHES. 360 SNAP-IN STACK ASSEMBLY. ADJUSTABLE POSITIVE STOP HEAD. ADJUST COUNTER BALANCE SPRING. FRONT EMERGENCY STOP. DUAL CYCLE START BUTTONS. ADDITIONAL FEATURES: AUTOMATIC FREQUENCY TUNING. WELD, HOLD, DELAY AND AFTER-BURST TIMERS. BACK-LIT LCD DISPLAY. ULTRASONIC LOAD METER SCALE. UPPER AND LOWER WELD LIMIT SETTINGS. SOFT-START OVERLOAD PROTECTION CIRCUITRY. LOAD REGULATION CIRCUITRY. DIGITAL WATTAGE DISPLAY. NON-CONTACT CYCLE START BUTTONS: OPTIONAL. AUTOMATION LIMIT SWITCHES: OPTIONAL. RIGID MOUNT BOOSTER: OPTIONAL. STAND ALONE COLUMN HUB: OPTIONAL. EXTENDED LENGTH COLUMN: OPTIONAL.

2002 FADAL 4020HT VERTICAL MACHINING CENTER TRAVELS X-AXIS: 40 INCH | Y-AXIS: 20 INCH | Z-AXIS: 20 INCH TABLE TABLE SIZE: 47.9 INCH 20.4 INCH | MAX TABLE LOAD: 3,641 LBS SPINDLE NOSE TO TABLE TOP: 4 INCH 24 INCH FEED RATES RAPID TRAVERSE: 900 IPM SPINDLE SPINDLE SPEED: 10,000 RPM | SPINDLE TAPER: CAT-40 | SPINDLE MOTOR: 15 HP AC TOOL CHANGER 21-POSITION ATC MAX TOOL DIAMETER: 3 INCH / 6 INCH (WITHOUT ADJACENT) | MAX TOOL LENGTH: 15 INCH | MAX TOOL WEIGHT: 15 LBS MACHINE DIMENSIONS & WEIGHT DIMENSIONS: 146 INCH L 103 INCH W 128 INCH H | MACHINE WEIGHT: ~10,800 LBS S/N: 12002094688

AMADA HFA-400W SAW, SERIAL NUMBER 40660313

AMADA HFA-400W SAW, SERIAL NUMBER 40660311

COOPER WEYMOUTH PETERSON SE 12 B 12" COIL FEEDER. MODEL NO: SE 12 B. STOCK WIDTH: 12 INCHES. STOCK THICKNESS IN MILD STEEL: .018 - .125 INCHES. SPEED: 50 FPM. MACHINE DIRECTION: R-L (RIGHT TO LEFT). AIR SUPPLY: 80-100 PSI. POWER SUPPLY: 460 V / 3 PH / 60 HZ. FULL LOAD AMPS: 15. S/N: C15592

2016 JUNGHEINRICH EKS 308 ORDER PICKER S/N FN522520 (36 VOLT) YEAR OF MANUFACTURE: 2016 MODEL/OPTION: EKS 308, Z+I 105 550 ZT MANUFACTURER: JUNGHEINRICH AG, 22039 HAMBURG, GERMANY MADE IN GERMANY CAPACITY RATED CAPACITY: 1000 KG / 2205 LBS LOAD CENTER DISTANCE: 610 MM / 24 IN RESIDUAL LIFT CAPACITY: 1000 KG / 2200 LBS CAPACITY DE-RATE BY LIFT HEIGHT: LIFT HEIGHT: 24 IN 28 IN 31 IN CAPACITY: 2200 LB 1910 LB 1670 LB (REDUCE TRUCK CAPACITY BY ANY OPERATOR WEIGHT OVER 100 KG / 220 LB) LIFT / MAST MAX. LIFT HEIGHT: 6310 MM / 248 IN HOISTING SPEED (LOADED): 0.31 M/S HOISTING SPEED (UNLOADED): 0.39 M/S WEIGHTS WEIGHT OF TRUCK (NO BATTERY, 5%): 2704 KG / 5962 LBS APPROX. TOTAL SERVICE WEIGHT: ~3.75 T (WITH BATTERY) BATTERY WEIGHT, MIN: 927 KG / 2044 LBS BATTERY WEIGHT, MAX: 1025 KG / 2260 LBS ELECTRICAL / BATTERY SYSTEM VOLTAGE: 36 V MAX. BATTERY CAPACITY: 840 AH BATTERY ID: EO DISCHARGE (HOUR RATE): 6 H NOMINAL DRIVE POWER: 6.9 KW HOIST MOTOR POWER: ~7.5 KW PERFORMANCE TRAVEL SPEED (LOADED/UNLOADED): 11.5 KM/H (~7.1 MPH) DIMENSIONS (GENERAL EKS 308 36V PLATFORM) WHEELBASE: 1.69 M / 67 IN TRANSPORT LENGTH: 3.275 M / ~129 IN TRANSPORT WIDTH: 1.0 M / ~39 IN TRANSPORT HEIGHT: 2.32 M / ~91 IN WORKING AISLE WIDTH: 1.22 M / ~48 IN ADDITIONAL NOTES: LOW HOURS, ORIGINALLY BOUGHT FOR WAREHOUSE RACKING WELL-MAINTAINED BUT HAVE BEEN IN STORAGE IN THE WAREHOUSE FOR A FEW YEARS, NOT SURE ON BATTERY LIFE EACH MACHINE COMES WITH ITS OWN CHARGER AND SET OF FORKS

2005 HAAS VF-3D TABLE SIZE: 48" X 18" MAX. TABLE LOAD: 3,500 LBS T-SLOTS: 3 SLOTS, 5/8" WIDE X-AXIS TRAVEL: 40" Y-AXIS TRAVEL: 20" Z-AXIS TRAVEL: 25" SPINDLE NOSE TO TABLE: 4"-29" RAPID TRAVERSE (X/Y/Z): 1,000 IPM MAX CUTTING FEED RATE: 500 IPM MAX THRUST X/Y: 2,550 LBF MAX THRUST Z: 4,200 LBF SPINDLE SPEED: 0-7,500 RPM SPINDLE TAPER: CAT 40 SPINDLE MOTOR: 20 HP PEAK MAX TORQUE: 90 FT-LBS @ 2,000 RPM DRIVE: 2-SPEED GEARBOX ATC STYLE: SIDE-MOUNT (SMTC) ATC CAPACITY: 24 STATIONS MAX TOOL DIAMETER (ADJACENT FULL): 3.5" MAX TOOL LENGTH (FROM GAGE LINE): 13" MAX TOOL WEIGHT: 12 LBS TOOL-TO-TOOL: 4.2 SEC (AVG) CHIP-TO-CHIP: 4.5 SEC (AVG) POSITIONING: .0002" REPEATABILITY: .0001" HAAS 32-BIT CNC CONTROL DISPLAY: 12" CRT SCREEN MEMORY: 1 MB PROGRAM MEMORY INTERFACES: HARD DISK DRIVE, FLOPPY, ETHERNET, RS-232C, USB FEATURES: RIGID TAPPING, COORDINATE ROTATION & SCALING, MACROS, 4TH-AXIS PREWIRED POWER: 195-260 VAC, 3-PHASE / 50A (OR 354-488 VAC / 30A) AIR REQUIRED: 4 SCFM @ 100 PSI COOLANT CAPACITY: 55 GAL MACHINE DIMENSIONS (L X W X H): 144" X 96" X 110" MACHINE WEIGHT: ~12,500 LBS

ATRUMP K2V MANUAL KNEE MILL STANDARD TABLE SIZE: 42" X 9" (1,066MM X 228MM) OPTIONAL TABLE SIZE: 49" X 9" (1,245MM X 228MM) T-SLOTS: 3 SLOTS X-AXIS TRAVELS: 30-1/4" STD (770MM) / 37-1/4" OPT (948MM) Y-AXIS TRAVELS: 12-3/4" (325MM) Z-AXIS TRAVELS: 17" (430MM) QUILL DIAMETER: 3-3/8" (86MM) QUILL TRAVEL: 4-7/8" (125MM) QUILL AUTO FEED RATES: 0.002", 0.004", 0.006" PER REV SPINDLE TAPER: R8 (OR NST #30 OPTIONAL) SPINDLE MOTOR: 3 HP / 4-POLE SPINDLE SPEED (60 HZ): 70-4,200 RPM (VARIABLE) DRIVE: MECHANICAL VARIABLE SPEED (VARI-DISC BELT SYSTEM) OVERALL HEIGHT: 83-1/2" (2,120MM) OVERALL DEPTH: 67-1/8" (1,706MM) OVERALL WIDTH: 57-3/4" (1,466MM) SPINDLE NOSE TO TABLE (MIN-MAX): 2-3/8"-19-1/4" (60-490MM) SPINDLE CENTERLINE TO COLUMN (MIN-MAX): 0"-19-3/8" (0-493MM) TABLE SURFACE TO SPINDLE NOSE (MIN-MAX): 4-1/2"-19-3/4" (114-504MM) SPINDLE NOSE TO FLOOR (MIN-MAX): 5"-20-3/8" (127-517MM) NET WEIGHT: 2,227 LBS (1,010 KG)

20"X60" KOBE MACHINERY CO., LTD. RUBBER INTERNAL INTENSIVE MIXER PACKAGE INCLUDES: SPARE ROLLER (IN ITS ORIGINAL PACKAGING) VENTILATION HOOD TALC BATH/SLAB DIP DRYING CONVEYOR W/FANS STERLCO TEMPERATURE CONTROL UNIT PARAMETER 22" 60" FRONT ROLL SPEED 15 RPM BACK ROLL SPEED 18 RPM FRICTION RATIO 1.22 MOTOR (SINGLE MILL) 150 HP MOTOR (TWIN MILL) 300 HP

MAZAK QUICK TURN 250 CNC TURNING CENTER STANDARD CHUCK SIZE: 10 INCHES MAXIMUM SWING OVER BED: 26.5" 26.6" (675 MM) MAXIMUM MACHINING DIAMETER: 14.75" 14.76" (380 MM) MAXIMUM BAR CAPACITY: 3.0" 3.1" (77 80 MM) MAXIMUM MACHINING LENGTH: ~20" 40" (500 MM 1,025 MM, DEPENDING ON BED LENGTH OPTION) MAIN SPINDLE MAXIMUM SPINDLE SPEED: 4,000 RPM SPINDLE MOTOR POWER: 26 KW 26.1 KW (35 HP) SPINDLE BORE: 3.58" (91 MM) SPINDLE NOSE: A2-8 TURRET & TOOLING NUMBER OF TOOL STATIONS: 12-POSITION DRUM TURRET INDEXING TIME: ~0.2 SEC (STATION-TO-STATION) AXIS TRAVEL & FEED RATES X-AXIS TRAVEL: 9.0" (230 MM) Z-AXIS TRAVEL: 22.6" 43.1" (575 MM 1,095 MM, MODEL VARIANT DEPENDENT) RAPID TRAVERSE RATE (X / Z): UP TO 1,181 IPM / 1,299 IPM (30 M/MIN / 33 M/MIN)

HSK 100 HEAT SHRINK TOOL HOLDERS - VARIOUS SIZES AND LENGTHS

BROOMFIELD LAB SERIES 500C COIL WINDER WITH BROOMFIELD LAB RANGER TRAVERSE