Monthly SIGMA Showroom Floor MultiIndustry Auction

MARBURG IND HEAT SHRINK TUNNEL WITH CONVEYOR WITH: APERTURE DIMENSIONS: WIDTH: 4 INCHES HEIGHT: 4 INCHES WORKING APERTURE DIMENSIONS: WIDTH: 2.5 INCHES HEIGHT: 4 INCHES TUNNEL LENGTH: 22 INCHES CONVEYOR DIMENSIONS: LENGTH: 31 INCHES WIDTH: 10 INCHES VARIABLE HEAT TEMPERATURE OVERALL DIMENSIONS: LENGTH: 32 INCHES WIDTH: 22 INCHES HEIGHT: 54 INCHES

FISHER CONTROLS 667 DIAPHRAGM ACTUATOR WITH: ACTUATION: SPRING-RETURN, LINEAR CERTIFICATIONS: SIL CAPABLE, ATEX, CUTR, PED CONTROL TYPE: ON/OFF, THROTTLING OPERATING TEMPERATURE: CRYOGENIC, LOW TEMPERATURE, STANDARD TEMPERATURE, HIGH TEMPERATURE POWER SOURCE: PNEUMATIC, MANUAL VALVE TYPE: ANGLE VALVE, GLOBE VALVE

AEROVENT VBBD VANEAXIAL 20HP BLOWER FAN - USED AEROVENT VANEAXIAL BLOWER WITH: OUTPUT: 20,000 CFM BELT DRIVEN DIMENSIONS: LENGTH: 49 INCHES DIAMETER: 42 INCHES TECO WESTINGHOUSE MOTOR: 20 HP 1760 RPM ELECTRICAL: VOLTS: 480 FREQUENCY: 60 HZ PHASE 3

HEAT SEAL 1730LB-1 MANUAL L BAR SEALER WITH: SEALING DIMENSIONS: WIDTH: 18 INCHES LENGTH: 30 INCHES OPENING HEIGHT: 10 INCHES MAXIMUM WEB WIDTH: 18 INCHES PERFORATOR ATTACHMENT CONVEYOR DIMENSIONS: LENGTH: 33 INCHES WIDTH: 13 INCHES ELECTRICAL REQUIREMENTS: 115 VOLTS, 60 HETZ, 20 AMPS OVERALL DIMENSIONS: LENGTH: 62 INCHES WIDTH: 24 INCHES HEIGHT: 40 INCHES

MANUAL L-BAR SEALER - USED PREFERRED PACKAGING L-BAR SEALER WITH: SEAL AREA DIMENSIONS: LENGTH: 20 INCHES WIDTH: 28 INCHES MAXIMUM FILM ROLL WIDTH: 25 INCHES EXIT CONVEYOR WIDTH: 17 INCHES DISCHARGE HEIGHT: 34 INCHES ON CASTERS ELECTRICAL: 220 VOLTS, 60 HZ, PHASE 1, 15 AMPS

HIBAR SERVO DISPENSING SYSTEM WITH: STAINLESS STEEL CONSTRUCTION 3.2 HORSEPOWER DIGITAL CONTROL PANEL EMERGENCY STOP ELECTRICAL REQUIREMENTS: 100/240 VOLTS, 50/60 HERTZ, 1 PHASE OVERALL DIMENSIONS: LENGTH: 34 INCHES WIDTH: 19 INCHES HEIGHT: 28 INCHES

FISHER CONTROLS 667 DIAPHRAGM ACTUATOR WITH: ACTUATION: SPRING-RETURN, LINEAR CERTIFICATIONS: SIL CAPABLE, ATEX, CUTR, PED CONTROL TYPE: ON/OFF, THROTTLING OPERATING TEMPERATURE: CRYOGENIC, LOW TEMPERATURE, STANDARD TEMPERATURE, HIGH TEMPERATURE POWER SOURCE: PNEUMATIC, MANUAL VALVE TYPE: ANGLE VALVE, GLOBE VALVE

WALKOVER PLATFORM STEEL 16'L X 32"W 56.5" TALL WITH: TOTAL LENGTH: 16' LONG STAIRWAY WIDTH: 32" WIDE CLEARENCE HEIGHT: 56" TALL PAINTED STEEL CONSTRUCTION SAFETY YELLOW RAILING COMPLETE WELDS FOR DURABILITY

NEW BLOWER FAN WHEEL 66 IN. DIAMETER STEEL WELDING WITH: IMPELLER: 66" DIAMETER QUARTER INCH WELDED STEEL SHAFT INCLUDED: 2.75" DIAMETER ON OEM PALLET

BLOWER FAN WHEEL 66 IN. DIAMETER STEEL WELDING WITH: IMPELLER: 66" DIAMETER QUARTER INCH WELDED STEEL SHAFT INCLUDED: 2.75" DIAMETER ON OEM PALLET

USED OTC FLOOR CRANE HOIST 1000 POUND CAPACITY CASTERS WITH: CASTERS FOR TRANSPORTATION CAPACITY: 1000 POUND CAPACITY WITH BOOM IN 750 POUND CAPACITY WITH BOOM IN MIDDLE 600 POUND CAPACITY WITH BOOM OUT PAINTED STEEL CONSTRUCTION HYDRAULIC OPERATION

C.E. KING SC4 TABLET COUNTER WITH: SPEED: UP TO 100 CONTAINERS PER MINUTE CHANGE PARTS NEEDED ON CASTERS ELECTRICAL REQUIREMENTS: 220 VOLTS, 60 HERTZ, 1 PHASE OVERALL DIMENSIONS: LENGTH: 44 INCHES WIDTH: 20 INCHES HEIGHT: 62 INCHES

ZALKIN CA-8-320 8 HEAD STAINLESS CHUCK CAPPER - USED NEWMAPAK CHRIMP CAPPER WITH: CONVEYOR: WIDTH: 4.5 INCHES HEIGHT: 48 INCHES SPEED: 320 BOTTLES PER MINUTE 8 HEAD ROTARY STYLE CAPPER ELECTRICAL PHASE3 PH HERTZ60HZ

THOMAS ENGINEERING ACCELA-COTA MKIII SPRAY COATER: TUMBLING DRUM DIAMETER: 59 INCHES DEPTH: 47 INCHES 6 BAFFLES 6 HEAD SPRAY COATER INFEED HEIGHT: 39 INCHES PUSH BUTTON CONTROLS TIMER STAINLESS STEEL CONSTRUCTION

PNEUMATIC LIQUID PRESS WITH JACKETED HOPPER: HOPPER CAPACITY: 3 GALLONS JACKETED HOPPER MAWP: 50 PSI @ 300F MDMT: -20F @ 50 PSI STAINLESS STEEL CONSTRUCTION OVERALL DIMENSIONS: LENGTH: 28 INCHES WIDTH: 28 INCHES HEIGHT: 73 INCHES

FILAMATIC 4 HEAD PISTON FILLER - USED FILAMATRIC PISTON FILLER WITH: CONVEYOR DIMENSIONS: LENGTH: 8 FEET WIDTH: 4 INCHES OVERALL ADJUSTABLE HEIGHT CURRENT DISCHARGE HEIGHT: 34 INCHES (4) STAINLESS STEEL FILLING HEADS INCLUDES STAINLESS STEEL HOLDING TANK ELECTRICAL: 115 VOLTS, 60 HZ, PHASE 1

CLIMAX DP4-1/LD DROP CASE PACKER - USED CLIMAX PACKAGING DROP CASE PACKER WITH: STAINLESS STEEL CONSTRUCTION MAXIMUM OUTPUT: UP TO 28 CASES PER MINUTE (DEPENDING ON PRODUCT AND CONFIGURATION) CASE SIZE RANGE: MINIMUM: 8 INCHES LONG X 8 INCHES WIDE X 3 INCHES HIGH MAXIMUM: 22 INCHES LONG X 15 INCHES WIDE X 16 INCHES HIGH 6 LANES APPROXIMATE DIMENSIONS: LENGTH: 12 FEET WIDTH: 42 INCHES ELECTRICAL: VOLTS: 460 FREQUENCY: 60 HZ PHASE 3 AIR REQUIREMENTS: 60PSI

AIR CUSTOM CPW CHILLER WITH: CAPACITY: 7.5-30 TONS DUAL STAGE CONTROLLED THERMOSTAT SHELL AND TUBE CONDENSORS SCROLL COMPRESSORS SINGLE AND DUAL INDEPENDENT REFRIGERANT CIRCUITS R-4IOA REFRIGERANT HINGED DOORS CRANKCASE HEATERS HIGH AND LOW PRESSURE SWITCHES STAINLESS STEEL FRAME

TOP OF SLURRY PUMP - USED SLURRY PUMP TOP WITH: APPROXIMATE OVERALL DIMENSIONS: LENGTH: 29 INCHES WIDTH: 24 INCHES HEIGHT: 68 INCHES

USED SLURRY PUMP WITH: APPROXIMATE OVERALL DIMENSIONS: WIDTH: 51 INCHES LENGTH: 30 INCHES HEIGHT: 96 INCHES TOP MOUNTED MOTOR

STOKES VACUUM PUMP WITH 15 HORSEPOWER BALDOR MOTOR - USED STOKES VACUUM PUMP WITH: SELF-CONTAINED ROTARY OIL SEALED PISTON TYPE UNIT FILTER HOUSING 300 CFM RATING ELECTRICS: VOLTAGE: 208-230/460 AMPS: 41-38/19 HERTZ: 60 PHASE: 3 BALDOR MOTOR: HORSEPOWER: 15 RPM: 1760

USED SACHET PACKET SEALER WITH: PACKET SIZE LENGTH: 5 INCHES WIDTH: 1.5 INCHES SEAL BAR LENGTH: 4 INCHES CHAIN LENGTH: 44 INCHES (2) LANES STAINLESS STEEL CONSTRUCTION OVERALL DIMENSIONS: LENGTH: 48 INCHES WIDTH: 15 INCHES HEIGHT: 42 INCHES

USED SACHET PACKET SEALER WITH: PACKET SIZE: LENGTH: 5 INCHES WIDTH: 1.5 INCHES SEAL BAR LENGTH: 4 INCHES CHAIN LENGTH: 44 INCHES (2) LANES STAINLESS STEEL CONSTRUCTION OVERALL DIMENSIONS: LENGTH: 48 INCHES WIDTH: 15 INCHES HEIGHT: 34 INCHES

USED SACHET PACKET SEALER WITH: PACKET SIZE: LENGTH: 4 INCHES WIDTH: 1.5 INCH SEAL BAR LENGTH: 4 INCHES CHAIN LENGTH: 44 INCHES (2) LANES STAINLESS STEEL CONSTRUCTION OVERALL DIMENSIONS: LENGTH: 51 INCHES WIDTH: 20 INCHES HEIGHT: 46 INCHES

HIBAR DEPOSITOR WITH: DIGITAL CONTROL PANEL STAINLESS STEEL CONSTRUCTION ELECTRICAL REQUIREMENTS: 208 VOLTS, 60 HERTZ, 3 PHASE OVERALL DIMENSIONS: LENGTH: 32 INCHES WIDTH: 42 INCHES HEIGHT: 70 INCHES

USED SLURRY PUMP WITH: APPROXIMATE OVERALL DIMENSIONS: WIDTH: 51 INCHES LENGTH: 30 INCHES HEIGHT: 96 INCHES TOP MOUNTED MOTOR

TIPPMANN DIE CUTTING CLAMP - USED TIPPMAN CLAMP WITH: WORKING AREA: WIDTH: 48 INCHES LENGTH: 32 INCHES CLAMP SIZE: WIDTH: 24 INCHES LENGTH: 12 INCHES TABLE HEIGHT: 35 INCHES MOUNTED ON LOCKABLE CASTERS

DOUBLE WELDING TANK CART - USED TANK CART WITH: OVERALL DIMENSIONS: WIDTH: 29 INCHES LENGTH: 24 INCHES HEIGHT: 47 INCHES CHAIN FOR HOLDING UPRIGHT TANKS ROOM FOR (2) NORMAL SIZED CYLINDERS STORAGE BOX: WIDTH: 23 INCHES LENGTH: 5 INCHES HEIGHT: 3 INCHES

MOVINCOOL CLASSIC PLUS 26 AC UNIT - USED MOVINCOOL AC UNIT WITH: TWO FILTERS PUSH BUTTON CONTROLS FRONT OPENING DIAMETER: 6 INCHES ELECTRICAL REQUIREMENTS: 208/230 VOLTS, 1 PHASE, 60 HERTZ

USED SIFTING CONVEYOR WITH: MILD STEEL FRAME STEEL MESH SCREEN

UNIPAK WD-7797 AUTOMATIC BOTTLE DEPALLETIZER S/N: 8000A110 WITH: PALLET SIZE: 44 X 56 (INCHES) HOIST: PALLET STATIONARY W/ LAYER TRANSPORT REMOVING LAYER AND TRANSFERRING TO ACCUMULATION TABLE HEAVY WELDED STEEL LEG STRUCTURE 5 HP BRAKE MOTOR W/ FREQUENCY CONTROLLER AUTOMATIC HEIGHT CONTROL W/ PHOTOEYE FOR LOCATING TOP OF PALLET AUTOMATIC PALLET POSITIONING STOP PUSH BUTTON CONTROL STATION NEMA 12 WIRED CONTROL PANEL CIRCUIT BREAKER FUSED DISCONNECT SWITCH TRANSFORMER ALLEN-BRADLEY (1500) P. L.C. W/ PANEL VIEW 600 PLUS 110" MAX. PALLET LOAD HEIGHT (INCLUDING PALLET) LAYER SWEEP: ON TRAVELING PLATFORM FRONT & REAR SWEEP PUSHER FLIGHT BAR DRIVEN BY SEPARATE 3/4 HP MOTORS SWEEP TRANSFERS OFF THE PALLET AND ONTO ACCUMULATION TABLE LAYER SHEET GRIPPERS: DUAL SET OF CAM ACTIVATED JAW TYPE GRIPPERS GRIPPERS MOUNTED ON REAR STACK ALIGNMENT PUSHER LAYER SHEET STORAGE: AUTOMATIC LAYER SHEET STORAGE IS LOCATED AT THE SIDE OF HOIST ACCUMULATION TABLE: 8' LONG X 4' WIDE (STANDARD BUILT TO SUIT ALL APPLICATIONS) 1 HP MOTOR W/ VARIABLE FREQUENCY CONTROLLER REX SERIES 8505 FLUSH GRID MATT CHAIN OR INTERLOX 900 RAISE RIB TWO SWITCHES ON TABLE HIGH LEVEL TO CONTROL SWEEP CYCLE LOW LEVEL TO CONTROL SINGLE FILLING SINGLE FILER EMPTY PALLET STACKER: HEAVY DUTY SCISSOR LIFT EMPTY PALLET CONVEYOR FROM HOIST TO STACKER INFEED PALLET CONVEYOR: 7' LONG (STANDARD) 1 HP MOTOR W/ VARIABLE SPEED EACH OPERATES INDEPENDENT OF EACH OTHER EACH CONVEYOR HAS PHOTOEYE DETECTION OF PALLET ELECTRICAL: VOLTS: 460 FREQUENCY: 6 HZ PHASE 3

G-FORCE G5-A CENTRIFUGE - USED G-FORCE PAINT PUMP: BOTTOM MOUNTED RESERVOIR TOP MOUNTED DISCHARGE: DIAMETER: 2 INCHES 15 HORSEPOWER MOTOR SKID MOUNTED

HOFFMAN DUST COLLECTION SYSTEM WITH: ONE (1) GLASS TANK: 41 DIAMETER X 112 HEIGHT (INCHES) TOP MOUNTED INLET: 9 INCHES BOTTOM MOUNTED OUTLET: 6 INCHES MANUAL FLOW CONTROL VALVES OVERALL HEIGHT: 192 INCHES ONE (1) FILTER TANK: 41 DIAMETER X 112 HEIGHT (INCHES) TOP MOUNTED INLET: 6 INCHES BOTTOM MOUNTED OUTLET: 6 INCHES MANUAL FLOW CONTROL VALVE OVERALL HEIGHT: 178 INCHES

VON GAL VAL-U-PAL LOW LEVEL PALLETIZER OUTPUT: UP TO 10 CASES PER MINUTE CYCLE RATE: UP TO 4 CYCLES PER MINUTE MAXIMUM LIFT WEIGHT: 250 POUNDS 30 POUNDS WITH SUCTION CUPS MAXIMUM LOAD HEIGHT: 6 FEET 8 INCHES PALLET MAGAZINE PALLET DIMENSIONS: 48 INCHES X 40 INCHES 6 HEAD SUCTION PICK UP: 3 CUPS PER SECTIONS CHAIN PALLET CONVEYOR: LENGTH: 15 FEET WIDTH: 43 INCHES HEIGHT: 18 INCHES ROLLER PRODUCT CONVEYOR: LENGTH: 14 FEET WIDTH: 31 INCHES HEIGHT: 38 INCHES PNEUMATIC CASE ROTATOR DROPPED CASE DETECTOR LOW PALLET DETECTION ELECTRICAL: VOLTS: 460 FREQUENCY: 60 HZ PHASE 3

VARIOUS CONVEYOR BELTS STEEL WIRE PLASTIC ROLLER RACKS BEARINGS

APM MFA-26-P SHRINK BUNDLER AND HEAT TUNNEL. FILM WIDTH: 22 INCHES. DUAL LANE INFEED: 4 INCHES WIDE (EACH). SECO GUAGES. SHRINK TUNNEL WIDTH: 17 INCHES. HEIGHT: 16 INCHES. STEEL MESH CONVEYOR. DISCHARGE: 36 INCHES. PUSH BUTTON CONTROLS. ELECTRICAL: 480 VOLTS, 3 PH, 60 HZ. STAINLESS STEEL CONTACT SURFACES.

6 STAINLESS STEEL BUCKETS: DIAMETER: 12 INCHES DEPTH 12 INCHES 4 STAINLESS STEEL TRAYS (2) TRAYS: LENGTH: 18 INCHES WIDTH: 6 INCHES DEPTH: 7 INCHES (2) TRAYS: LENGTH: 12 INCHES WIDTH: 6 INCHES DEPTH: 12 INCHES

AUTOMATIC LABELLING MACHINE - USED AUTOMATIC LABELER WITH: AUTOMATIC MONOBLOCK COLD GLUE LABELER PREVIOUSLY RAN 12 OZ BEER BOTTLES APPLIED FRONT, BACK AND NECK LABELS 24 LABELING STATIONS INFEED DIMENSIONS: HEIGHT: 49 INCHES WIDTH: 3.5 INCHES TIMING WHEEL PRODUCT DIAMETER: 2 INCHES PROTECTIVE GUARDING SIEMENS TOUCHSCREEN HMI PUSH START/STOP BUTTONS STAINLESS STEEL CONSTRUCTION ELECTRICS: VOLTS: 460 PHASE:1 HERTZ:60

DIVERSIFIED STEAM CAPPER WITH: CONTAINER CONVEYOR (MISSING BELT): LENGTH: 105 INCHES WIDTH: 4 INCHES INFEED/DISCHARGE HEIGHT: 35 INCHES RESINA STYLE CAP SORTER: 32 INCH DIAMETER CAP HOPPER: LENGTH: 30 INCHES WIDTH: 30 INCHES DEPTH: 20 INCHES PUSH BUTTON CONTROLS WASHDOWN IDC MOTOR ELECTRICAL: VOLTS: 460 FREQUENCY: 60 HZ PHASE 3

2020 GKS FB-640 10 LANE SACHET TOWELETTE MACHINE - USED GKS TOWELETTE MACHINE WITH: 10 LANES BLUE BELT PRODUCT INSPECTION CONVEYORS: APPROXIMATE LENGTH: 300 INCHES WIDTH: 26.5 INCHES INFEED HEIGHT: 26 INCHES DISCHARGE HEIGHT: 41 INCHES PRODUCT DISCHARGE FUNNEL LENGTH: 6.5 INCHES WIDTH: 15 INCHES HEIGHT: 23 INCHES CURRENT PRODUCT PACKAGE WIDTH: 2 INCHES HEIGHT:2 INCHES MAX FILM WIDTH: 50 INCHES 10 HEAD PRESSURE FILLER (2) 5 STATION FABRIC CUTTERS WITH 6 SEAM ROLLERS PER SECTION 3 STAGE STRIP FOLDER TEAR NOTCH ESCHERICH STATIK AIR SYSTEM LAST RUNNING TOWELETTES: LENGTH: 4.75 INCHES WIDTH: 7 INCHES 6 VERTICAL FOLDS 3 HORIZONTAL FOLDS SERVO DRIVEN ALLEN BRADLEY PANELVIEW PLUS HMI ELECTRICAL: 480 VOLTS, 3 PH, 60 HZ

BUCKEYE BOILER COMPANY COMPRESSED AIR SURGE TANK WITH: SHELL RATING: 150 POUNDS PER SQUARE INCH VACUUM READOUT MOUNTED ON LEGS DIMENSIONS: 20 DIAMETER X 48 HEIGHT (INCHES)

30 INCH DIAMETER BUTTERFLY VALVE - USED BUTTERFLY VALVE BUTTERFLY DOOR: 30 INCHES DIMENSIONS: OUTSIDE DIAMETER: 36 INCHES HEIGHT: 6 INCHES

USE BLUE ROLLING CART WITH: FRAME DIMENSIONS: LENGTH: 94 INCHES WIDTH: 42 INCHES HEIGHT: 38 INCHES PAINTED STEEL FRAME LOCKABLE CASTERS

METALTECNO ROLLER CONVEYOR 63" L X 80" W - USED METALTECNO ROLLER CONVEYOR WITH: CHAIN DRIVEN CONVEYOR: LENGHT: 63 INCHES WIDTH: 80 INCHES DICHARGE: 45 INCHES ROLLERS: DIAMETER: 2.5 INCHES CENTERS: 6 INCHES 41 INCH VERTICAL LIFT OVERALL DIMENSIONS: LENGTH: 63 INCHES WIDTH: 105 INCHES HEIGHT: 100 INCHES ELECTRICAL: VOLTS: 460 FREQUENCY: 60 HZ PHASE 3

HAYSSEN ULTIMA VERTICAL FORM FILL AND SEAL BAGGER ONLY - USED HAYSSEN ULTIMA WITH: OUTPUT: UP TO 100 BAGS PER MINUTE MINIMUM BAG DIMENSIONS: LENGTH: 3 INCHES WIDTH: 2 INCHES MAXIMUM BAG DIMENSIONS: LENGTH: 8 INCHES WIDTH: 8 INCHES AIR REQUIREMENTS: 65 PSI ELECTRICAL: 230 VOLTS, 1 PH, 60 HZ

PEERLESS PBD 6 BREAD AND DOUGH DIVIDER WITH: STAINLESS STEEL HOPPER: 28 INCHES LONG X 26 INCHES DEPTH X 16 INCHES WIDTH ROLLER WIDTH: 28 INCHES CONVEYOR: 54 INCHES LENGTH X 12 INCHES WIDTH ALLEN BRADLEY PANEL VIEW 100 6 POCKET BREAD DIVIDER RATES: 60-180 PIECES PER MINUTE DEPENDING ON NUMBER OF HEADS, MATERIALS, AND APPLICATION PRODUCT RANGE FOR: WHITE BREADS VARIETY BREADS ETHNIC BREADS FROZEN DOUGH 6-60 OUNCES ALL DRIVEN BY HYDRAULIC CYLINDERS: FLOUR DUSTER RAM KNIFE DIVISION BOX EJECTOR HYDRAULIC PUMP VOLTAGE480 ELECTRICAL PHASE3PH HERTZ60HZ

GENERON NITROGEN GENERATOR WITH: COMBINE POLYMER HOLLOW FIBER MEMBRANES OXYGEN ANALYZER ACTIVATED CARBON FILTER POWDER COATED STEEL BACK PANEL PURITY CONTROL VALVE STAINLESS STEEL PIPING AIR REQUIREMENTS: 14.5 PSI INLET TEMPERATURE: 75F DEW POINT: 38F APPROXIMATE OVERALL DIMENSIONS: LENGTH: 32 INCHES WIDTH: 32 INCHES HEIGHT: 87 INCHES

2016 PEARSON CE60-TL CASE ERECTOR AND BOTTOM GLUE SEALER - USED CASE ERECTOR AND BOTTOM GLUE SEALER WITH: OUTPUT RATE: UP TO 55 CASES PER MINUTE ERECTED CASE SIZE RANGE: LENGTH: 12 INCHES TO 23 INCHES WIDTH: 5.5 INCHES TO 16 INCHES OPEN DEPTH: 5.5 INCHES TO 22.5 INCHES KNOCKED-DOWN SIZES: LENGTH: 17.5 INCHES TO 36 INCHES WIDTH: 8.25 INCHES TO 30.5 INCHES BOTTOM FLAP WIDTH: 3 INCHES TO 8 INCHES CHAIN DRIVEN BELT INFEED WIDTH: 4.5 INCHES HOT MELT GLUE UNIT ALLEN-BRADLEY PLC ELECTRICAL: 460 VOLTS, 3 PH, 60 HZ RIGHT HAND CASE MACHINE

STAINLESS SMOKE GENERATOR WITH HOPPER - USED SMOKE GENERATOR WITH: AGITATED HOPPER: DIAMETER: 24 INCHES DEPTH: 24 INCHES STAINLESS STEEL CONSTRUCTION

STAINLESS STEEL SMOKE GENERATOR WITH: AGITATED HOPPER: DIAMETER: 30 INCHES DEPTH: 28 INCHES STAINLESS STEEL CONSTRUCTION