Beverage Processing and Packaging Equipment Auction

KRONES AUTOCOL STAINLESS STEEL ROTARY WRAPAROUND PRESSURE SENSITIVE LABELER, UP TO 300 LABELS PER MINUTE, 14 STATIONS, FILM ROLL DIAMETER: 15.75 INCHES (400MM), CORE DIAMETER: 2.95 INCHES (75MM), TIMING SCREW LENGTH: 28 INCHES, FLIGHT: 3 INCHES, APPROXIMATE OVERALL DIMENSIONS: LENGTH: 9 FEET, WIDTH: 8.5 FEET, HEIGHT: 7.5 FEET, ALLEN-BRADLEY PANELVIEW PLUS 600 HMI, STAINLESS STEEL CONSTRUCTION, ELECTRICAL: 3 PHASE, 60 HZ, 460 VOLTS, PREVIOUSLY USED IN 12OZ GLASS BEER BOTTLE APPLICATION

AMF B30 HPS STAINLESS STEEL BREAD BASKET WASHER AND DRYER - AMF WASHING AND DRYING SYSTEM OFFERS OPTIMIZED WATER AND AIR HEATING SOLUTIONS BY MEANS OF GAS, STEAM OR HEAT RECOVERY SYSTEM. BASKETS ARE CLEANED AND DRIED IN A CONTINUOUS MOTION WITHOUT BASKET ACCUMULATION. BASKETS PASS THROUGH A HIGH-PERFORMANCE NOZZLE SYSTEM USING FILTERED HOT WATER. FOR MAXIMUM CLEANING EFFICIENCY, FRESH WATER INTAKE IS CONTROLLED TO ELIMINATE WASH SOLUTION TEMPERATURE DROP. BASKETS ARE DRIED BY AN AIR KNIFE TECHNOLOGY COMBINED WITH A MOISTURE ELIMINATOR SYSTEM THAT RECIRCULATES AIR AND ELIMINATES EXCESS MOISTURE WHILE REDUCING OVERALL ENERGY CONSUMPTION. SINGLE TUNNEL CONTINUOUS MOTION WASHER AND DRYER OUTPUT: UP TO 50 BASKETS PER MINUTE DEPENDING ON THE APPLICATION ADJUSTABLE BASKET SIZE ACCOMMODATION AUTOMATIC DRUM FILTRATION STAINLESS STEEL CHAIN CONVEYOR WITH PUSH BARS WASHER LENGTH: 20 FEET DRYER LENGTH: 20 FEET CENTRIFUGAL CIRCULATING PUMPS TOUCHSCREEN CONTROLS ELECTRICAL: VOLTS: 480 FREQUENCY: 60 HZ PHASE 3 STAINLESS STEEL CONSTRUCTION (3) LAARS MIGHTY THERM BOILERS MODEL: B30 HPS

SACMI OPERA C2 ROLL FED GLUE LABELER, DESIGNED TO APPLY WRAP-AROUND GLUE LABELS TO CYLINDRICAL SHAPED CONTAINERS AT HIGH SPEEDS, PRODUCTS IT CAN RUN: PET, GLASS OR METAL, PREVIOUSLY RUNNING: 20 OUNCE, 1 LITER, AND 1.5 LITER BOTTLES, RITTAL TOP THERM ENCLOSURE COOLING UNIT: REFRIGERANT TYPE, CHARGE: R134A, 18 OUNCES, ALLEN BRADLEY PUSH BUTTON CONTROLS, ELECTRICALS: 480 VOLTAGE / 3 PHASE / 60 HERTZ, MODEL: M0209517

SWITCHBACK SLS72D-3 STAINLESS STEEL DUAL LANE TRAY FORMER, DUAL HEAD. CURRENT MANDREL DIMENSIONS: LENGTH: 9.25 INCHES WIDTH: 7.5 INCHES. CURRENT FORMING AREA: LENGTH: 10.25 INCHES WIDTH: 7.5 INCHES. MAGAZINE DIMENSIONS: LENGTH: 32 INCHES WIDTH: ADJUSTABLE. DISCHARGE CONVEYOR DIMENSIONS: LENGTH: 180 INCHES WIDTH: 12 INCHES. INFEED/DISCHARGE HEIGHT: 12.5 INCHES. ADJUSTABLE GUIDE RAILS. AUTO-ADVANCED CARTON MAGAZINES. ROTARY STYLE SUCTION INFEED. ALLEN BRADLEY PLC CONTROLS: VFD AND SERVO SPEED CONTROL THROUGH HMI. CYCLE RATE DISPLAYED ON HMI. FAULTS ANNUNCIATED ON HMI. PUSHBUTTON CONTROL FOR STOP, START AND JOG. CARTON JAM DETECTION. ELECTRICAL REQUIREMENTS: 240 VOLTS, 60 HERTZ, 3 PHASE. STAINLESS STEEL CONSTRUCTION. MOUNTED ON CASTERS. OVERALL DIMENSIONS (EXCLUDING CONVEYOR): LENGTH: 84 INCHES WIDTH: 94 INCHES HEIGHT: 108 INCHES.

SWITCHBACK SLS72D-3 DUAL LANE STAINLESS STEEL LOCK STYLE TRAY FORMER, DUAL HEAD, CURRENT MANDREL DIMENSIONS: LENGTH: 9.25 INCHES WIDTH: 7.5 INCHES, CURRENT FORMING AREA: LENGTH: 10.25 INCHES WIDTH: 7.5 INCHES, MAGAZINE DIMENSIONS: LENGTH: 32 INCHES WIDTH: ADJUSTABLE, DISCHARGE CONVEYOR DIMENSIONS: LENGTH: 180 INCHES WIDTH: 12 INCHES, INFEED/DISCHARGE HEIGHT: 12.5 INCHES, ADJUSTABLE GUIDE RAILS, AUTO-ADVANCED CARTON MAGAZINES, ROTARY STYLE SUCTION INFEED, ALLEN BRADLEY PLC CONTROLS: VFD AND SERVO SPEED CONTROL THROUGH HMI, CYCLE RATE DISPLAYED ON HMI, FAULTS ANNUNCIATED ON HMI, PUSHBUTTON CONTROL FOR STOP, START AND JOG, CARTON JAM DETECTION, ELECTRICAL REQUIREMENTS: 240 VOLTS, 60 HERTZ, 3 PHASE, STAINLESS STEEL CONSTRUCTION, MOUNTED ON CASTERS, OVERALL DIMENSIONS (EXCLUDING CONVEYOR): LENGTH: 84 INCHES WIDTH: 94 INCHES HEIGHT: 108 INCHES

KRONES SOLOMODUL 4 STATION ROTARY FRONT AND BACK PRESSURE SENSITIVE LABELER, OUTPUT: 550 CONTAINERS PER MINUTE DEPENDING ON THE APPLICATION, 4 STATIONS, FRONT AND BACK LABELING, PRESSURE SENSITIVE LABELS, MAXIMUM LABEL LENGTH: 7 INCHES (180MM), WORM SCREW INFEED, STARWHEEL BOTTLE HANDLING, ELECTRICAL: VOLTS: 480, FREQUENCY: 60 HZ, PHASE 3, STAINLESS STEEL CONSTRUCTION

CERMEX F39741 DUAL LANE HIGH SPEED GLUE CASE ERECTOR, 70 CASES PER MINUTE. DUAL LANE BELT FED CASE MAGAZINE AND CASE ERECTING. CASE DIMENSIONS: LENGTH: 6-12 INCHES, WIDTH: 4-10 INCHES, HEIGHT: 6-12 INCHES. INFEED DIMENSIONS: LENGTH: 10 FEET, WIDTH: 27 INCHES. NORDSON GLUE UNIT, SERVO CONTROLLED AUTOMATIC ADJUSTMENTS, DUAL ALLEN BRADLEY TOUCHSCREEN CONTROLS. ELECTRICAL: 480 VOLTS, 60 HZ, 3 PHASE. AIR REQUIREMENTS: 80 PSI. STEEL CONSTRUCTION. RIGHT HAND CASE ERECTING. LEFT TO RIGHT OR RIGHT TO LEFT OPERATION. CAN RUN RSC AND HALF CASES AS WELL AS CASES WITH SPECIAL FLAPS AND PRE-JOINED DISPLAY CASES.

KRONES SOLOMODUL 1200-25 GLUE LABELING SYSTEM. OUTPUT RANGE: 4,700 TO 37,400 BOTTLES PER HOUR. TWO (2) AGGREGATE STATIONS: LABEL LENGTH MAXIMUM: 180 MILLIMETERS. COLD GLUE STATION. STEEL GLUE ROLLER. CONTAINER INFEED: DESIGNED FOR 2 INFEED WORMS (ON TOP OF EACH OTHER). INFEED DESIGN: BOTTLE STOP STARWHEEL. NUMBER OF CONTAINER PLATES (HEADS): 25. NUMBER OF DOCKING STATIONS: 2. FEED DIRECTION: LEFT TO RIGHT. MACHINE PITCH: 150.7 MILLIMETERS. STAINLESS STEEL CONSTRUCTION. CONTROL UNIT: SIEMENS S7 300. ELECTRICAL REQUIREMENTS: 460 V, AC 3-PHASE CURRENT, 60 HZ, 45 A (FULL LOAD MAX), 6.6 A (FULL-LOAD AMPS OF LARGEST MOTOR). PREVIOUSLY RAN 16.9 OZ WATER BOTTLES AT 1,200 BOTTLES PER MINUTE APPLYING LABELS 8.25 INCHES LONG BY 1.3 INCHES WIDE.

ACCRAPLY 350BT AUTOMATIC SERVO TOP AND/OR BOTTOM LABELER, CURRENTLY SET UP TO RUN: 115 MILLIMETER TOP LABEL AND A 90 MILLIMETER BOTTOM LABEL (DIAMETER) PRODUCT: 120 MILLIMETER DIAMETER X 50 MILLIMETER HEIGHT OUTPUT: UP TO 120 PRODUCTS PER MINUTE DEPENDING ON APPLICATION TOP LABEL DIMENSION: 115 MILLIMETERS DIAMETER BOTTOM LABEL DIMENSIONS: 90 MILLIMETERS DIAMETER HEAVY GAUGE STAINLESS STEEL BASE FRAME DUAL SIDE BELT PRODUCT TRANSPORT WITH ADJUSTABLE SPEED PHOTOELECTRIC PRODUCT SENSOR SERVO SP10 APPLICATORS (2) VIDEOJET DATA FLEX 6420 TRANSFER PRINTERS AIR ASSISTED LABEL PEELER LABEL APPLICATION METHOD: TAMP ARM CONTAINER GEOMETRY: CYLINDRICAL ELECTRICALS: 380 VOLTS / 1 PHASE / 60 HERTZ MODEL: 350B-S

KRONES SOLOMODUL 1200-25 GLUE LABELING SYSTEM. OUTPUT RANGE: 4,700 TO 37,400 BOTTLES PER HOUR. TWO (2) AGGREGATE STATIONS. LABLE LENGTH MAXIMUM: 180 MILLIMETERS. COLD GLUE STATION. STEEL GLUE ROLLER. CONTAINER INFEED: DESIGNED FOR 2 INFEED WORMS (ON TOP OF EACH OTHER). INFEED DESIGN: BOTTLE STOP STARWHEEL. NUMBER OF CONTAINER PLATES (HEADS): 25. NUMBER OF DOCKING STATIONS: 2. FEED DIRECTION: LEFT TO RIGHT. MACHINE PITCH: 150.7 MILLIMETERS. STAINLESS STEEL CONSTRUCTION. CONTROL UNIT: SIEMENS S7 300. ELECTRICAL REQUIREMENTS: 460 VAC, 3-PHASE CURRENT, 60 HZ, 45 A (FULL LOAD MAX), 6.6 A (FULL-LOAD AMPS OF LARGEST MOTOR). PREVIOUSLY RAN 16.9 OZ WATER BOTTLES AT 1,200 BOTTLES PER MINUTE APPLYING LABELS 8.25 INCHES LONG BY 1.3 INCHES WIDE.

BARRY-WEHMILLER PC-900 18HD 18 HEAD ROTARY CAPPER, UP TO 300 BOTTLES PER MINUTE, CURRENT SET UP FOR CAP SIZE 38X38 MM, CAPPING HEAD CENTERS: 6.5 INCHES, STARWHEEL BOTTLING HANDLING, ALLEN BRADLEY TOUCHSCREEN CONTROLS, STAINLESS STEEL CONSTRUCTION, LEFT TO RIGHT OPERATION.

SACMI FORMSLEEVER 500 LABELER, SPEEDS UP TO 866 PER MINUTE, SUITABLE FILMS: PET, OPS, PO, PVC, PLA, OPP AND OTHERS, MAXIMUM LABEL SIZE: 175MM/6.9 INCHES, MINIMUM LABEL SIZE: 30MM/1.2 INCHES, MAXIMUM CONTAINER SIZE: 350MM/13.8 INCHES, MINIMUM CONTAINER SIZE: 150MM/5.9 INCHES, MAIN TURRET: CONTAINERS ARE ROTATED AROUND AXIS SO LABELS CAN BE APPLIED, TUBULAR SLEEVE APPLIED, SLEEVE CAN BE FULL OR PARTIAL BODY, LABELING UNIT: PHOTOCELL NEAR INLET WHEEL GENERATES SIGNAL AND STARTS LABELING PROCESS, LABELING TAPE TRANSFERRED FROM REEL TO DRIVE ROLLER, DRIVE ROLLER ADJUSTS TO MAKE SURE CUTTING POINT IS CORRECT, SOLVENT APPLIED TO LABEL AND SLEEVE IS SEALED, REEL UNWINDER, CONTROL CABINET, ELECTRICALS: 480 VOLTAGE / 3 PHASE / 60 HERTZ, OPERATION: AUTOMATICALLY LOADS, APPLIES WRAP AROUND LABELS TO CONTAINERS, AND THEN UNLOADS THEM, CONTAINERS ENTER ON A SINGLE ROW CONVEYOR AND TRANSFERRED TO THE MAIN TURRET

PNEUMATIC SCALE ANGELUS 4V ATMOSPHERIC 4 HEAD ROTARY CAN SEAMER, RATED FOR 100 TO 450 CONTAINERS PER MINUTE. CURRENTLY SET UP FOR 210 DIAMETER CANS (CHANGE PARTS REQUIRED FOR DIFFERENT DIAMETERS). MINIMUM CAN DIAMETER: 200, MINIMUM CAN HEIGHT: 46 MILLIMETERS, MAXIMUM CAN DIAMETER: 401, MAXIMUM CAN DIAMETER: 203 MILLIMETERS. TRANSFER CHAIN PITCH: 164.0B MILLIMETERS. 4 SEAMING STATIONS. INFEED AND DISCHARGE: RANDOM INFEED WITH SERVO TIMING SPIRAL. DRIVEN TABLETOP FEED CHAIN. SEAMER DISCHARGE TABLE CONVEYOR. FEED LINE HEIGHT: 1250 MILLIMETERS WITH +/- 50 MILLIMETER ADJUSTMENT. MOTORIZED TURRET ELEVATING MECHANISM (1/2 HORSEPOWER). JAM STOP SWITCH. HANDWHEEL (MANUAL TURRET ROTATION). LOW COVER SENSOR. UPPER AND LOWER OIL CYCLE SENSOR. BASE OIL LEVEL SENSOR. OIL FILTRATION AND INJECTION PUMP. OIL HEATER. INFEED CLUTCH JAM SENSOR. DISCHARGE TORQUE JAM SENSOR. NEMA 4 CONTROL CABINET WITH LOCKABLE DISCONNECT. OIL LUBRICATION AND FILTRATION SYSTEM. STAINLESS STEEL CONSTRUCTION.

EAC STAINLESS STEEL TABLETOP WATER HEATER, OVERALL DIMENSIONS: LENGTH: 17 INCHES WIDTH: 21 INCHES HEIGHT: 18 INCHES CONSTRUCTION: STAINLESS STEEL ELECTRICAL: 220 V / 0.45 A / SINGLE PHASE

25 GALLON SS MIXING TANK WITH DURA IPULSE GS 20X VARIABLE SPEED CONTROLLER. CAPACITY OF TANK: 25 GALLONS. STAINLESS STEEL TANK. INNER TANK DIMENSIONS: 21 INCH DIAMETER X 22 INCHES DEEP. INLET PORT DIAMETER: 2.5 INCHES. OUTLET PORT DIAMETER: 2.5 INCHES. REVES PUMP.

MATEER PACKAGING HEAD, 1/2 HORSEPOWER, 1725 ROTATIONS PER MINUTE, STAINLESS STEEL CONSTRUCTION, ELECTRICAL REQUIREMENTS: 230/460 VOLTS, 60 HERTZ, 3 PHASE

MATEER PACKAGING HEAD AUGER FILLER, 1/2 HORSEPOWER, 1725 ROTATIONS PER MINUTE, STAINLESS STEEL CONSTRUCTION, ELECTRICAL REQUIREMENTS: 230/460 VOLTS, 60 HERTZ, 3 PHASE

125 GALLON STAINLESS STEEL SINGLE WALL TANK, CAPACITY: 125 GALLONS, TANK DIMENSIONS: DIAMETER: 28 INCHES HEIGHT: 54 INCHES, SIDE BOTTOM DISCHARGE DIAMETER: 2 INCHES, CENTER TOP INLET DIAMETER: 2 INCHES, STAINLESS STEEL CONSTRUCTION

100-GALLON STATIONARY STAINLESS STEEL KETTLE, CAPACITY: 100 GALLONS, POWER TYPE: STEAM, JACKET: FULL, STYLE: STATIONARY, DRAWOFF: 2 INCH SANITARY TANGENT, MAWP: 45 PSI @ 650F, OVERALL DIMENSIONS: DEPTH: 48 INCHES, WIDTH: 50.25 INCHES, HEIGHT: 36 INCHES, MOUNTED ON FOUR CASTERS, EXTERIOR CONSTRUCTION: 304 STAINLESS STEEL, INTERIOR CONSTRUCTION: 316 STAINLESS STEEL

MATEER PACKAGING HEAD, 1/2 HORSEPOWER, 1725 ROTATIONS PER MINUTE, STAINLESS STEEL CONSTRUCTION, ELECTRICAL REQUIREMENTS: 230/460 VOLTS, 60 HERTZ, 3 PHASE, HEAD ONLY

100 GALLON GROEN GT-100 JACKETED STAINLESS STEEL KETTLE, STEAM POWERED, FULL JACKET, STATIONARY STYLE, 2 INCH SANITARY TANGENT DRAWOFF, MAWP: 45 PSI @ 650F, OVERALL DIMENSIONS: DEPTH: 48 INCHES, WIDTH: 50.25 INCHES, HEIGHT: 36 INCHES, MOUNTED ON FOUR CASTERS, EXTERIOR CONSTRUCTION: 304 STAINLESS STEEL, INTERIOR CONSTRUCTION: 316 STAINLESS STEEL

STAINLESS STEEL MIXER MOUNT WITH 20 HORSEPOWER ELECTRIC MOTOR: 230/460 VOLTS, 60 HERTZ, 3 PHASE

500 GALLON STAINLESS STEEL DUAL LID SINGLE WALL TANK - USED 500 GALLON TANK WITH: CAPACITY: 500 GALLONS (APPROXIMATELY) TANK DIMENSIONS (INCHES): DIAMETER: 52 DEPTH: 64 DISCHARGE FLANGED DIAMETER: 2 INCHES OVERALL DIMENSIONS (INCHES): LENGTH: 56 WIDTH: 56 HEIGHT: 124 MOUNTED ON (4) LEGS BOTTOM CENTER DISCHARGE CONICAL BOTTOM STAINLESS STEEL CONSTRUCTION

SANI-MATIC 20 GALLON STAINLESS STEEL BREW HOPPER, WORKING CAPACITY: 20 GALLONS, NUMBER OF TANKS: 2, OPERATING PRESSURE: 6 BAR, CONTROL AIR PRESSURE: 6 TO 8 BAR, CONE DRIVE RATIO: 5:1, WAUKESHA CHERRY-BURRELL PUMP: 3 HORSEPOWER, MOUNTED ON STAINLESS STEEL FRAME, STAINLESS STEEL CONSTRUCTION, ELECTRICAL REQUIREMENTS: 208-230/460 VOLTS, 60 HERTZ, 3 PHASE

1972 PAUL MUELLER SS 75 GALLON JACKETED TANK, STAINLESS STEEL CONSTRUCTED WITH 3 LEG MOUNT, OPEN TOP, DIAMETER 29.5 INCHES, OUTLETS SIDE MOUNT (2) - 2 INCHES DIAMETER, BOTTOM MOUNT (1) - 1 INCH DIAMETER, TANK HEIGHT: 29 INCHES, HEAT TRANSFER SURFACE TAG: MAX WORKING PRESSURE- 90 PSI, MAX TEMPERATURE - 350 DEGREES FAHRENHEIT, NATIONAL BOARD CERTIFICATION - 1775 S/N: 118101-3

20 CUBIC FOOT SINGLE SHAFT DUAL RIBBON BLENDER, TANK CAPACITY: 20 CUBIC FOOT, INTERIOR TANK DIMENSIONS: 65 INCHES LONG X 25 INCHES WIDE X 25 INCHES DEEP, SINGLE SHAFT DUAL RIBBON BLENDER, MOTOR: 5 HORSEPOWER, BOTTOM SLIDE GATE DISCHARGE: 12 INCHES X 7 INCHES, DISCHARGE HEIGHT FROM GROUND: 34 INCHES, ELECTRICAL REQUIREMENTS: 208-230/460 3 PHASE 60 HZ

SCOTT EQUIPMENT COMPANY PUG 1030 DUAL SHAFT CARBON STEEL MIXER - USED SCOTT MIXER WITH: SHAFT DIAMETER: 2 INCHES MIXING CHAMBER OPENING: LENGTH: 30 INCHES WIDTH: 9.5 INCHES INFEED HEIGHT: 43 INCHES DISCHARGE HEIGHT: 33 INCHES DISCHARGE DIMENSIONS: LENGTH: 9 INCHES WIDTH: 5 INCHES OVERALL DIMENSIONS: LENGTH: 58 INCHES WIDTH: 35 INCHES HEIGHT: 51 INCHES CARBON STEEL CONSTRUCTION ELECTRICAL: 440 VOLTS PREVIOUSLY USED IN FIBER PROTEIN MIXING APPLICATION

200 GALLON AOL200 STAINLESS STEEL SUSPENSION TANK, CAPACITY: 200 GALLONS, PRODUCTION SPEED: 67 GALLONS PER HOUR, MINIMUM CONDENSING CAPACITY: -30 F AT 18,000 BTU AN HOUR, AGITATION TYPE: PROPELLER, TANK DIMENSIONS: DIAMETER: 42 INCHES, DEPTH: 41 INCHES, MANWAY DIAMETER: 19 INCHES, MOTOR: HP: 0.5 RPM: 950, ELECTRICAL: 95 VOLTS, 5.5 AMPS, 1 PHASE, MOUNTED ON PAINTED MILD STYLE FRAME AND CASTERS FOR MOBILITY, STAINLESS STEEL CONSTRUCTION

200 GALLON STAINLESS STEEL PRESSURE KETTLE, MAWP: 125 PSI @ 353 F, BOTTOM CENTER FLANGED DISCHARGE: DIAMETER: 2.25 INCHES, HEIGHT FROM FLOOR: 23.5 INCHES, SIDE BOTTOM OUTLET DIAMETER: 2.25 INCHES, HALF JACKETED, JACKET INLET DIAMETER: 1.5 INCHES, DISH BOTTOM, TOP MOUNTED PADDLE AGITATION, SIDE SCRAPE, OVERALL DIMENSIONS: DIAMETER: 48 INCHES, HEIGHT: 104 INCHES, MOUNTED ON PAINTED STEEL FRAME, 316 STAINLESS STEEL CONSTRUCTION, MOTOR: 2 HORSEPOWER, ELECTRICAL: 3 PHASE, 60 HZ, 550 VOLTS, PREVIOUSLY USED IN BAKERY APPLICATION

ROTATING FILLER FRAME, NOZZLE DIAMETER: 3/4 INCHES, STATION DIMENSIONS: LENGTH: 6.5 INCHES WIDTH: 3.25 INCHES (24) STATIONS, TOUCHSCREEN HMI, ELECTRICAL REQUIREMENTS: 130 VOLTS, 60 HERTZ, 1 PHASE, OVERALL DIMENSIONS: LENGTH: 39 INCHES WIDTH: 50 INCHES HEIGHT: 75 INCHES

EPAK MACHINERY 6 HEAD INLINE LIQUID GRAVITY FILLER WITH HOLDING TANK, 6 INLINE PNEUMATIC ACTUATED FILLING HEADS, 7/16 INCH DIAMETER FILL NOZZLES, 1 INCH LONG FILL NOZZLES, MANUAL CLEAN IN PLACE SYSTEM, (2) 3/4 INCH DIAMETER STAINLESS STEEL PRODUCT SUPPLY CONTROL VALVES WITH LEVEL SENSOR, IN TANK FLOAT SYSTEM, ALLEN BRADLEY/MICROLOGIX 1200 CONTROLS, AUTOMATIC DRIP TRAY, AUTOMATIC PIN STYLE INDEXING SYSTEM, PHOTO SENSOR FOR COUNTING SYSTEM, ANTI BACK UP SENSOR SHUT DOWN, 304 STAINLESS STEEL FRAME, AIR REQUIREMENTS: 80-100 PSI COMPRESSED DRY AIR, ELECTRICAL REQUIREMENTS: 115 VOLTS / 1 PHASE / 50-60 HERTZ, PRODUCT LAST RAN: BUBBLES

E PAK 10 HEAD INLINE PRESSURE GRAVITY FILLER WITH 15' LONG CONVEYOR, 10 FILING HEADS (CAPABLE OF HOLDING UP TO 20 HEADS), FILL HEADS DIAMETER: 3/8 INCHES, CONVEYOR: 15 FEET LONG 4.5 INCHES WIDE, STANDARD LINE HEIGHT RANGE: 32 TO 38 INCHES FROM GROUND, TOOL-LESS ADJUSTABLE RAIL BRACKETS, VARIABLE SPEED CONTROLLER, 304 STAINLESS STEEL HEAVY DUTY FRAME, 316 STAINLESS STEEL 3/4" PNEUMATIC ACTUATED FILL VALVES, BRAIDED PVC TUBING AND FITTINGS, ALLEN BRADLEY/MICROLOGIX 1200 CONTROLS WITH NEMATRON TOUCH SCREEN, AUTOMATIC SET UP CAPABILITIES, IN TANK FLOAT, DRIP TRAY, BOTTLE INDEXING SYSTEM, PHOTO SENSOR/COUNTING SYSTEM, ELECTRICALS: 110 VOLTS / 1 PHASE / 50-60 HERTZ, COMPRESSED AIR: 80 - 100 PSI

ELF 8-HEAD STAINLESS STEEL INLINE GRAVITY PRESSURE FILLER, NUMBER OF NOZZLES: 8, NOZZLE DIAMETER: 3/4 INCH, STAINLESS STEEL HOPPER, PUSH BUTTON CONTROLS, MOUNTED ON (4) LEGS, STAINLESS STEEL CONSTRUCTION, ELECTRICAL REQUIREMENTS: 230/460 VOLTS, 60 HERTZ, 3 PHASE

HOPPMANN CORPORATION FT50-21 47 INCH DIAMETER SS STAINLESS STEEL CENTRIFUGAL CAP SORTER WITH BELT FEEDER. HOPPMANN FT50-21 BOWL FEEDER: BOWL DIAMETER: 47 INCHES, BOWL RIM WIDTH: 4.12 INCHES, BOWL RIM TO BOTTOM OF FRAME: 24.88 INCHES, DISCHARGE HEIGHT: 36 INCHES (APPROXIMATELY). MOTOR: 0.75 HORSEPOWER. WEIGHT: 1050 POUNDS. STAINLESS STEEL CONSTRUCTION. WB-6 WIDE BELT PREFEEDER: CAPACITY: 6 CUBIC FEET, OVERALL LENGTH: 72 INCHES, OVERALL WIDTH: 51 INCHES, INFEED HEIGHT: 94 INCHES. UPPER BELT HORSEPOWER: 0.5, LOWER BELT HORSEPOWER: 0.033. STAINLESS STEEL CONSTRUCTION. VARIABLE SPEED CONTROL. PUSH BUTTON CONTROLS. MOUNTED ON A STAINLESS STEEL FRAME. ELECTRICAL: 3 PHASE, 60 HERTZ, 230 VOLTS. MODEL: FT50-21

HOPPMANN CORPORATION 52 INCH DIAMETER CENTRIFUGAL BOTTLE UNSCRAMBLER MOUNTED ON A FRAME - SHIBUYA HOPPMANNS STANDARD FRS-60 CENTRIFUGAL FEEDER IS SPECIFICALLY DESIGNED TO FEED A WIDE RANGE OF LARGE BOTTLES AND PARTS. THE DELIVERY RATE VARIES FROM MODERATE TO HIGH SPEED DEPENDING ON PART CHARACTERISTICS. THE FRS-60 CENTRIFUGAL FEEDER IS ENGINEERED TO INTERFACE WITH SHIBUYA HOPPMANN PREFEEDERS, ACCUMULATING CONVEYORS, ASSEMBLY SYSTEMS AND OTHER DOWNSTREAM EQUIPMENT. USED HOPPMANN STAINLESS STEEL BOWL FEEDER WITH: BOWL INSIDE DIAMETER: 52 INCHES RIM WIDTH: 3.61 INCHES SCALLOP LENGTH: 12 INCHES INFEED HEIGHT: 66 INCHES DISCHARGE HEIGHT: 40 INCHES (APPROXIMATELY) OVERALL DIMENSIONS (INCHES): LENGTH: 82 WIDTH: 82 HEIGHT: 70 EQUIPMENT WEIGHT: 2500 POUNDS MOTOR: AC HORSEPOWER: 0.75 ELECTRICAL REQUIREMENTS: 3 PHASE, 60 HERTZ, 208-230-460 VOLTS MODEL: FRS-60

ELECTRIC BOILER, 120 KW, 480V, 150 PSI MAX WORKING PRESSURE. NEVER PUT INTO PRODUCTION. S/N:

16 HEAD INLINE PRESSURE FILLER WITH: FILL HEADS: 16 BRADFORD PUMP ELECTRICAL: 220 VOLTS, 60 HERTZ, 1 PHASE

32 HEAD VACUUM COUNTER PRESSURE FILLER UP TO 500 FILLS PER MINUTE - THE HORIX HOV3238 32-HEAD VACUUM COUNTER PRESSURE FILLER IS A HIGH-PERFORMANCE FILLING MACHINE DESIGNED FOR RAPID, EFFICIENT BOTTLING OF LIQUIDS. CAPABLE OF FILLING UP TO 500 CONTAINERS PER MINUTE, THIS SYSTEM UTILIZES 32 FILLING HEADS TO MAINTAIN HIGH THROUGHPUT AND CONSISTENCY. IT OPERATES WITH A VACUUM COUNTER-PRESSURE FILLING METHOD, ENSURING THAT THE LIQUID IS DISPENSED WITH MINIMAL FOAM FORMATION AND REDUCED OXYGEN EXPOSURE, MAKING IT IDEAL FOR SENSITIVE PRODUCTS LIKE CARBONATED BEVERAGES. THIS MACHINE IS SUITABLE FOR MEDIUM TO LARGE-SCALE PRODUCTION ENVIRONMENTS LOOKING FOR SPEED, RELIABILITY, AND QUALITY IN THEIR FILLING PROCESS. PRODUCTION SPEED: UP TO 500 FILLS PER MINUTE, DEPENDING ON APPLICATION HOPPER CAPACITY: 60 GALLONS SCREW PITCH: 2.75 CONVEYOR DIMENSIONS (INCHES): LENGTH: 162 WIDTH: 3.5 HOPPER DIMENSIONS (INCHES): DIAMETER: 51 DEPTH: 8 OVERALL DIMENSIONS (INCHES): LENGTH: 100 WIDTH: 70 WITHOUT CONVEYOR / 160 WITH CONVEYOR HEIGHT: 114 SERVO DRIVEN INFEED JOG CAPABILITY SANITARY FITTINGS RECENTLY REBUILT IN 2017, UPDATED TO MODERN STANDARDS ELECTRICAL: 3 PHASE, 60 HERTZ, 480 VOLTS LAST APPLICATION: 16 OUNCE SEA FOAM CANS AT 30 PER MINUTE. ORIGINAL USE WAS FOR WHISKEY AT 500 BOTTLES PER MINUTE. MODEL: HOV3238

RONCHI EXACTA/R MONOBLOC 16 HEAD MAGNETIC FLOW METER NET WEIGHT FILLER AND 5 HEAD CAPPER. VOLUMETRIC FLOW METERS SUITABLE TO HANDLE ALL PRODUCTS HAVING A MINIMUM LEVEL OF ELECTRICAL CONDUCTIVITY OF 5 S/CM. SANITARY VERSION AVAILABLE WITH ELECTRO-POLISHED PARTS, ORBITAL WELDING AND TRI-CLAMP CONNECTIONS. PHARMACEUTICAL PRODUCTS VERSION CAN BE PROVIDED WITH FDA CERTIFICATION. SUITABLE TO HANDLE VISCOUS AND FOAMY PRODUCTS FOUND IN THE CHEMICAL, COSMETIC, PHARMACEUTICAL AND FOOD FIELDS. 16 FILLING HEADS, FILL CAPACITY: UP TO 10 LITERS DEPENDING ON CHANGE PARTS. MAGNETIC FLOW METER NET WEIGH FILLING. FILLING ACCURACY: = 0.2 PERCENT. WORM SCREW INFEED, STAR WHEEL PRODUCT TRANSFER. 5 HEAD CHUCK CAPPER. ELECTRICAL: 460 VOLTS, 60 HZ, 3 PHASE. 304 STAINLESS STEEL CONSTRUCTION, 316L STAINLESS CONTACT PARTS.

KRONES SENSOMATIC 36 HEAD STAINLESS STEEL MONOBLOCK PRESSURE FILLER AND CAPPER - USED KRONES PRESSURE FILLER SYSTEM WITH: THROUGHPUT: UP TO 300 BOTTLES PER MINUTE DEPENDING ON SIZE AND APPLICATION NUMBER OF SEALING HEADS: 36 FILLING VALVES: 154 CROWNING HEADS: 9 PITCH: 103 MM PRODUCTION FLOW: LEFT TO RIGHT DOUBLE PRE-EVACUATION ADDITIONAL CO2 CHANNEL PROBE-ASSISTED FILL LEVEL CORRECTION LIFT CYLINDER MAXIMUM PRESSURE: 75 PSI BOWL TEST PRESSURE: 150 PSI CIP CAPABLE CURRENTLY TOOLED FOR 12 OUNCE BOTTLES OVERALL DIMENSIONS: LENGTH: 9 FEET WIDTH: 9 FEET HEIGHT: 7 FEET PUSH BUTTON CONTROLS THREADED LEVELER LEGS STAINLESS STEEL CONSTRUCTION MOTOR: 29.5 HORSEPOWER (22 KW) ELECTRICAL: 3 PHASE, 60 HZ, 550 VOLTS PREVIOUSLY USED IN BEER BOTTLING APPLICATION

GONGDA BEVERAGE DRYING, FILLING, CAPPING, AND LABELING LINE. FILLER/CAPPER: 16 HEAD, INFEED HEIGHT: 43.5 INCHES, DISCHARGE HEIGHT: 42.5 INCHES, RUNS LEFT TO RIGHT, CURRENT BOTTLE SIZE CONFIGURATION: 12 OUNCES 24 OUNCES, BOTTLE MATERIAL: PRESSURIZED GLASS, CAP DIAMETER: 13 MM, ADJUSTABLE HEIGHT FEET. LABELER: VARIABLE SPEED, ADJUSTABLE RAILS, INFEED HEIGHT: 44 INCHES, DISCHARGE HEIGHT: 44 INCHES, AUGER SCREW PITCH: 3 INCHES, RUNS LEFT TO RIGHT, FILM CORE DIAMETER: 2 INCHES, TOUCHSCREEN CONTROLS, STAINLESS STEEL CONSTRUCTION, ADJUSTABLE HEIGHT FEET. PACK OFF TABLE: INFEED HEIGHT: 41 INCHES, RAIL HEIGHT: 3 INCHES. OVERALL DIMENSIONS: LENGTH: 90 INCHES WIDTH: 73 INCHES HEIGHT: 86 INCHES (FILLER/CAPPER), LENGTH: 140 INCHES WIDTH: 33 INCHES HEIGHT: 67 INCHES (LABELER), LENGTH: 40 INCHES WIDTH: 24 INCHES HEIGHT: 45.5 INCHES (PACK OFF TABLE).