Gibbs Brower International CorporationVacating BuildingWill Continue to Broker Equipment

1994 CASTALDINI E100 EIS 2000 EVOLUZIONE PAPER BAG MACHINE. FLAT & GUSSETED PINCH BOTTOM BAGS. PERFORATOR CUTOFF. FILM WINDOW RUNS THE FRONT OF THE BAG; USED FOR BREAD BAGS. UNWIND ROLL OF FILM FOR WINDOW FILM. SINGLE PLY BAGS. FORMER OWNER'S TYPICAL PRODUCTION WHEN PRINTING 4-COLORS AND USING WINDOW FILM SYSTEM, 250 BAGS PER MINUTE ON 16" LONG WINDOW BAGS. MECHANICAL SPEEDS UP TO 600 BAGS PER MINUTE. SPEED DEPENDS ON PAPER, GLUE, IF PRINTING, IF MAKING WINDOW, INKS USED, ENVIRONMENT & OPERATOR'S SKILL. 380 VOLT, 3 PHASE, 50/60 CYCLE. 10 HP VARIABLE SPEED AC MOTOR. SIEMENS SIMEVERT AC DRIVE. EXCELLENT MECHANICAL CONDITION. 10" - 30" LENGTH BAG. 3.5" - 13" WIDE BAG. METRIC PITCH. 8 DP. 40" SINGLE POSITION UNWIND, FLOOR PICKUP, MOTORIZED SIDE SHIFT OF ROLL, 50" DIA. ROLLS, 3" CORE. MONTALVO AUTOMATIC TENSION; CONTROLS THE BRAKE. SECOND UNWIND USED FOR WINDOW FILM, 3" CORE, UP TO 9" WIDE FILM, MANUAL SIDE SHIFT, AIR BRAKE, 30" DIAMETER ROLLS. 40" CASTALDINI PRINTER, 4 COLORS, CONSTANT ROTATING INK FEATURE. AUTOMATIC PLATE CYLINDER LIFT. PUSH-BUTTON MOVEMENT OF PRINTER, +/- 4". CERAMIC ANILOX ROLLS. REPEAT RANGE OF PRINTER, 10" TO 30". (36) PRINT CYLINDERS INCLUDED; LIST AVAILABLE. (4) SPARE ANILOX ROLLS. (2) SPARE RUBBER ROLLS. ELECTRIC HOT-AIR DRYER. (10) FORMERS INCLUDED; LIST AVAILABLE. NORDSON HOT-MELT GLUE FOR WINDOW UNIT AND COLD GLUE FOR WINDOW; HAS BOTH. COLD GLUE FOR SEAM AND BOTTOM OF BAG. 43.5" WIDE IDLERS. EXCELLENT MECHANICAL CONDITION.

2002 SYNERCON PSA 450 DUPLEX, GENERAL PURPOSE SLITTER REWINDER S/N: 0237. WAS SLITTING & REWINDING TAPE PRODUCTS. NARROW WIDTH SLITTING. CENTER WIND. MINIMUM GAP REWIND. CANTILEVERED REWIND SHAFTS; REWIND SHAFTS STAY IN MACHINE. REWIND SHAFTS ALLOW FOR ADJUSTABLE MINIMUM GAP REWINDING WHICH ASSISTS WITH REWINDING NARROW SLIT ROLLS. DISTANCE FROM SLIT TO REWIND IS MINIMIZED. CANTILEVERED REWIND SHAFT MOUNTED ON A PIVOTED BRACKET TO PERMIT LOCATION OF THE REWIND IN ORDER TO MINIMIZE THE DRAW DISTANCE BETWEEN THE REWINDING ROLL AND IDLER ROLL. ATTACHED UNWIND. 12 MONTALVO AIR BRAKE WITH ULTRASONIC SENSOR FOR AUTOMATIC TENSION CONTROL OF BRAKING SYSTEM. ACCUWEB ELECTRIC AUTOMATIC EDGE GUIDING SYSTEM. EDGE GUIDES UNWIND LEFT / RIGHT +/- 2. UNWIND HAS AIR-LOADED LAYON PEELER PACKER ROLL WHICH CAN BE USED WHEN UNWINDING TAPE PRODUCTS. ASSISTS WITH EVEN UNWINDING OF PRODUCT. 42 DIAMETER UNWIND WITH 3 AIR UNWIND SHAFT. 6 CORE ADAPTORS. RUBBER-COVERED DRIVEN PULL ROLL. BOWED ROLL. 6.25 DIAMETER, HARDENED STEEL, MAIN DRUM. RAZOR SLITTING IN AIR; (10) RAZOR KNIFE BLADE HOLDERS. SCORE CUT SLITTING. (15) AIR-LOADED SCORE CUT KNIVES, .5 WIDE KNIVES / HOLDERS. ADDITIONAL SCORE CUT KNIVES CAN BE PURCHASED FOR $100.00US PER KNIFE. KNIVES ALLOW .5 MINIMUM SLIT WIDTH. TWO 3 DIFFERENTIAL REWIND SHAFTS, AIR LOADED FROM ONE SIDE. TWO 3 AIR-REWIND SHAFTS FOR LOCKED CORE REWINDING. VICKERS HYDRAULIC SYSTEM WHICH CONTROLS POSITION OF THE REWIND SHAFTS; THEY MOVE AUTOMATICALLY TO MAINTAIN A MINIMUM GAP AS REWINDING ROLL DIAMETER INCREASES. 24 REWIND DIAMETER. 3 MOTOR DRIVE. CONTROL TECHNIQUES CONTROLLER, MODEL UNIDRIVE. AC VARIABLE SPEED DRIVE, SET UP ON 230 VOLT, 3 PHASE, 60 CYCLE. (3) MARATHON ELECTRIC, 7.5 HP AC DRIVE MOTORS. ONE DRIVE MOTOR DRIVES PULL ROLL, SCORING ROLL. OTHER TWO MOTOR DRIVE EACH REWIND SHAFT. ALLEN BRADLEY PLC MICROLOGIX 1200 COMPUTER WITH ALLEN BRADLEY PANELVIEW 600 TOUCHSCREEN. MACHINE IS CAPABLE OF SLITTING & REWINDING BOTH EXTENSIBLE & NON-EXTENSIBLE PRODUCTS, PRESSURE-SENSITIVE TAPES, LABEL STOCK, LAMINATIONS, PAPERS, TEXTILES, NONWOVENS, FILM, FOILS, LIGHT & HEAVY-GAUGE FILMS. CANTILEVERED REWIND SHAFTS ASSIST WITH QUICK UNLOADING OF REWOUND ROLLS. 1000 FEET PER MINUTE WEB SPEED. TIMING BELTS ARE USED THROUGHOUT. LOW MAINTENANCE.

STANFORD 212 HD HEAVY-DUTY SINGLE SHAFT, CENTER REWIND SLITTER REWINDER. ALSO USED AS A ROLL DOCTOR. S/N: 8743839B. MODEL 212 HD. 2400 LBS. MAXIMUM ROLL WEIGHT. 2000 FEET PER MINUTE. SINGLE POSITION DETACHED UNWIND. SL SERIES. AIR CHUCKING TO HOLD UNWIND SHAFT IN PLACE. AIR-LOADED DANCER ROLL WHICH CONTROLS TENSION OF BRAKING AUTOMATICALLY. FIFE AUTOMATIC EDGE GUIDING SYSTEM, PNEUMATIC SENSOR, +/- 2. UNWIND ACCEPTS 60 DIAMETER ROLLS. PNEUMATIC CHUCKING FOR POSITIVE SAFETY LOCK FOR SHAFT RETAINING. STANFORD MODEL 900 PNEUMATIC DANCER CONTROLS. AIR TO PNEUMATIC BRAKE TO MAINTAIN CONSTANT TENSION. UNWIND SHAFTS & REWIND SHAFTS ARE INTERCHANGEABLE. (3) 6 AIR SHAFTS. (8) 3 AIR SHAFTS. SOME SHAFTS ARE BUTTON TYPE; SOME ARE LEAF TYPE. LEAF TYPE ARE TYPICALLY USED FOR NARROW SLITTING. CONSTANT TENSION REWINDING. REWIND HAS PNEUMATIC REWIND SHAFT RETAINING WITH POSITIVE SAFETY LOCKS. AIR-OPERATED RIDER ROLL PROVIDES CONTROLLED ROLL DENSITY; CAN CONTROL AMOUNT OF PRESSURE ON REWINDING ROLL. WRAP-TYPE SHEAR CUT SLITTING. SEPARATION OF UNIFORM CALIPER WEBS WHEN SLITTING IS ACCOMPLISHED WITH AN BOWED ROLL. ONE MALE SHEAR CUT KNIFE. APPROXIMATELY (80) FEMALE SHEAR CUT KNIVES. INCLUDES SPARE FEMALE SHEAR CUT KNIFE ROLL. 4 DIAMETER MOUNT HOPE BOWED ROLL MOUNTED ON RIDER ROLL ASSEMBLY AFTER MATERIAL HAS BEEN SLIT. RIDER ROLL IS 6 DIAMETER. CONTROL PRESSURE DOWN & UP. 50 DIAMETER REWIND. DURANT COUNTER WITH TWO PRESETS. INCLUDES TRIM BLOWER, UPGRADED DRIVE & MOTOR. AC VARIABLE SPEED, 460 VOLT, 3 PHASE, 60 CYCLE. ALLEN BRADLEY POWERFLEX 755 DRIVE WITH 25 HP BALDOR MOTOR. STANFORD 212 TYPICALLY IS USED FOR PAPER, PAPER/FOIL LAMINATES, NONWOVENS, NON-EXTENSIBLES, COATED & UNCOATED MATERIALS, CARBONLESS PAPER, TISSUE, TOWEL, TUBE & CORE STOCK, NON-EXTENSIBLES. MACHINE HAS RECENTLY BEEN REFURBISHED.

WEBER MODEL 7 AG VARIABLE SIZE, 1 OR 2-PLY, SOS, SQUARE BOTTOM PAPER BAG MACHINE. DESIGNED FOR 5" TO 9" WIDE, 3.5"-5.5" BOTTOM, 14.5"-30" TUBE LENGTH. THIS MACHINE IS AN ADJUSTABLE VARIABLE SIZE PAPER BAG MACHINE THAT CAN BE OPERATED AS A 1 OR 2-PLY MACHINE. 2-POSITION UNWIND, 40" WIDE, 60" DIAMETER ROLLS. NO UNWIND SHAFTS. ONE 38" CROSS THE WEB GLUE APPLICATING SYSTEM FOR COLD GLUE. CAN REGISTER APPLYING GLUE TO THE WEB. TYPICALLY USED WHEN MAKING 2-PLY BAGS. CAN REGISTER THE APPLICATION OF ADHESIVE TO THE WEB. THIS MACHINE HAD EMP ELECTRIC EYE SYSTEM INSTALLED, SERVO STYLE AND IT HAS BEEN REMOVED. NEEDS AN ELECTRIC EYE SYSTEM TO ALLOW FOR OPERATION OF PRE-PRINTED MATERIALS TO REGISTER THE CUTOFF. ALSO ALLOWS THE MACHINE TO CHANGE THE CUTOFF FROM THE SCREEN. NO CHANGE GEAR SYSTEM. THIS SYSTEM ALLOWS ANY PITCH PRINTER TO BE PUT INLINE WITH BAG MACHINE. MACHINE IS CAPABLE OF MAKING BAGS FROM 8 TO 35 LBS.; MAKES 2 KILO BAG. HAS ROTARY CUTOFF. AIR-LOADED, PLASMA-COATED DRAW ROLLS, WHICH ARE TYPICALLY USED FOR COATED PRINTED PAPERS. HAS BAG CARRIER & PRESSING UNIT. COLD GLUE POT FOR APPLYING GLUE TO THE SEAM. COLD GLUE BOTTOM POT FOR APPLYING GLUE TO THE BOTTOM OF THE BAG. TYPICAL MANUFACTURING SPEED IS 120 BAGS PER MINUTE, DEPENDENT UPON THE PAPER, OPERATORS SKILLS, GLUE & ENVIRONMENT. BASIS WEIGHT OF PAPER, FROM 30 TO 90 LB. MACHINE INCLUDES MODERN 20 HP ASHCROFT AC MOTOR WITH ALLEN BRADLEY POWERFLEX 755 SOLID-STATE CONTROLLER. 460 VOLT, 3 PHASE, 60 CYCLE. THUMBNOTCH CUTTING SYSTEM. RAZOR SLITTING ON THE FORMER. CAN HAVE LINESHAFT CONNECTION INSTALLED. DRUM HAS (4) SECTIONS, 10" WIDE DRUM. ONE 9" WIDE FORMER IS INSTALLED AND INCLUDED. 8-35 LB. BAGS ARE TYPICALLY MANUFACTURED ON THIS MACHINE.

CATERPILLAR GC45KS LPG FORKLIFT, 209" LIFT, 9100 LBS., NO FORKS, SIDESHIFT. 6024 HOURS S/N: AT87A00116

BLACK BROTHERS TB-60 HOT-ROLL LAMINATE HEAT-ACTIVATED ADHESIVE-BACKED DECORATIVE FOILS & PAPERS, TOP & BOTTOM SIMULTANEOUSLY. CAPABLE OF RUNNING UP TO 400 FIVE-FOOT WIDE BOARDS PER HOUR, SINGLE OR DOUBLE-SIDED. HIGH PRODUCTIVITY. DESIGNED TO WITHSTAND HIGH TEMPERATURES AND RIGOROUS USE. MACHINE COULD BE SET UP MANY DIFFERENT WAYS. JIB-TYPE CRANE TO EASILY LOAD PAPER FILM ROLLS ON UNWINDS. TYPICALLY USES PAPERS & FOILS FILMS PRE-COATED WITH ADHESIVE. OPERATOR SET UP CONTROLS, REGULATE THE HYDRAULIC PRESSURE AND UNWIND TENSION. HAS ELECTRICAL CONTROL PANEL; ALLOW OPERATOR TO MONITOR AND ADJUST THE SPEED, OIL TEMPERATURE & BRAKE PRESSURE. HEAVY-DUTY STEEL FRAME. CHROME-PLATED LAMINATING ROLLS ARE 1.5 THICK WITH 4 OD JOURNALS FOR MAXIMUM STRENGTH UNDER FULL HYDRAULIC PRESSURE. 65.5 FACE LENGTH ROLLERS; EASILY ACCOMMODATE 60 WIDE ROLLS. INTERNAL OIL HEATED UP TO 425 DEGREES FAHRENHEIT AND HIGH ROLL PRESSURES PRODUCE AN EXCELLENT BOND AND FINISH. HEAVY-DUTY HYDRAULIC CYLINDERS PROVIDE AMPLE PRESSURE FOR DIFFICULT TO RUN PRODUCTS. HAS RED LION COUNTER. TWO ROLLS ARE HEATED. SELF-CONTAINED UNIT. 13.5 DIAMETER HEATED LAMINATING ROLLS. TWO UNWIND POSITIONS. ONE 3 AIR UNWIND SHAFT. HAS GAP ADJUSTMENT BETWEEN TWO LAMINATING ROLLS. 500 LB. CAPACITY HOIST SYSTEM. INCLUDES OIL TANK & PUMP. MACHINE IS APPROXIMATELY 20 YEARS OLD. HAS AC TEC VARIABLE SPEED AC DRIVE, MODEL SCF. 230 VOLT, 3 PHASE, 60 CYCLE. BALDOR 5 HP AC MOTOR. UNWINDS WILL ACCEPT 24 & 40 DIAMETER ROLLS. MACHINE HAS BEEN REFURBISHED AND TESTED, REPAIRS MADE.

HARRIS SEYBOLD CJH-MBS FULL HYDRAULIC GUILLOTINE CUTTER / TRIMMER S/N: 3724. KNIFE, CHF-8A. WITH MICROCUT, SERIAL # MC6178. SET UP FOR 220 / 440 VOLT INPUT POWER. MACHINE HAS BEEN UPDATED OVER THE YEARS AND WAS OVERHAULED & REBUILT BY COLTER PETERSON. WAS CUTTING FILM PRODUCTS & PAPER. MINIMUM TRIM, 1/32. HAS VICKERS HYDRAULIC CLAMP. KNIFE BAR IS POWERED HYDRAULICALLY. HAS DOUBLE END PULL. MACHINE HAS 7.5 HP DAYTON AC MOTOR, SET UP 230 / 460 VOLT. APPROXIMATELY 85 BACKGAUGE. SIDE TABLES. UPPER CLAMP CLEARANCE, 7. TABLE IS AIR FILM DESIGN. FRONT OF TABLE TO KNIFE, 22. GENERAL SIZE TO CUT & SQUARE, 84. MAXIMUM 22 CUTS PER MINUTE. TWO SPARE KNIVES.

1991 PCMC ECM-14 HIGH-SPEED ELECTRONIC CORE MACHINE S/N: 7296. INCLUDES UNWIND STAND, ADHESIVE APPLICATION UNIT, CORE WINDING UNIT, SERVO DRIVEN CUTOFF MODULE. STANDARD PRODUCT RANGE: CORE STOCK WIDTH 2.5" - 3.5"; CORE INSIDE DIA. RANGE 1" - 2"; CORE LENGTH RANGE 60" MINIMUM - UNLIMITED MAXIMUM CUTOFF. MAXIMUM WALL THICKNESS .17". PRODUCT SPECIFICATIONS: CORE STOCK THICKNESS .015. CORE STOCK WIDTH 3". CORE INSIDE DIA. 1.65". 1.65" ID MANDREL. WAS MAKING 102" LONG CORES. UNWIND STAND WILL ACCEPT 50" DIA. ROLLS OF PAPER ON 3" CORES. 2 PLIES. (2) UNWINDS ARE BEING UNWOUND AT THE SAME TIME. GUARANTEES: SPEED-BASED USING GOOD QUALITY LIGHTWEIGHT CORE STOCK & HEATED ADHESIVE, 350 FPM OF FINISHED CORE, GUARANTEED 400 FPM DESIGN SPEED OR 60 CORES PER MINUTE, WHICHEVER COMES FIRST. CUTOFF ACCURACY: SET LENGTH +/- .0625". LEFT-HAND MACHINE. CUTOFF TO THE LEFT WHEN VIEWED FROM OPERATOR POSITION. NEW AC TECH LENZE, SMV INVERTER. (2) NEW AC DRIVE MOTORS; 5 HP EACH ON CORE WINDING UNIT. SET UP ON 400/460 VOLTAGE, 3 PHASE, 50 OR 60 CYCLE. TOTAL OF (4) UNWIND POSITIONS. HAS 4-POSITION UNWIND WITH DRAG BELT BRAKING. STANDARD HEATED GLUE POT. AIR CYLINDER FOR TENSION BETWEEN WINDING DRUMS. SERVO CONTROLLED ELECTRONIC CUTOFF MODULE. SAW CUTOFF. IN OCTOBER 2013, ORIGINAL SERVO CORE CUTTER ELECTRICS & MOTORS WERE REPLACED DUE TO BEING OBSOLETE. THEY HAVE BEEN REPLACED WITH A NEW BALDOR SERVO MOTOR AND NEW BALDOR (ABB) SERVO AMPLIFIER. THE FRONT END CONTROL & OPERATOR INTERFACE HAVE BEEN REPLACED WITH A NEW CONTREX M-SHUTTLE CONTROL. ALL PROGRAMMING INFORMATION WILL BE SUPPLIED WITH THE MACHINE. NEW ELECTRICAL DRAWINGS WILL REFLECT THE WIRING CLEANUP & CHANGES. ALL TECHNICAL INFORMATION NOT DIRECTLY SUPPLIED IS DIRECTLY AVAILABLE WITH INTERNET ACCESS. COPY OF MANUAL INCLUDED. AIR MOTOR IS USED FOR CUTOFF SAW BLADE. UNIT WAS INLINE WITH PCMC 250 SERIES WINDER. OPERATING AT 2,500 FPM. HIGH-SPEED SERVO DRIVEN CORE MACHINE.

2013 AMK / ROSS KE-40 KNEADER EXTRUDER / MIXER, CLASS IV. WORKING CAPACITY 40 GALLONS. CLASS IV CONSTRUCTION. STAINLESS STEEL. TWO AC MOTORS, 230/460 VOLT, 3 PHASE, 60 CYCLE. INCLUDES TOUCHSCREEN CONTROLS. DOES NOT HAVE DRIVES & STARTERS. JACKETED SYSTEM. HAS AUTOMATION DIRECT TOUCHSCREEN. AMK MACHINE KNE-0160L KNEADER EXTRUDER, SERIAL # 11966. MACHINE WAS PURCHASED IN 2013, RAN PRODUCT; USED FOR MIXING ADHESIVES FOR TAPE INDUSTRY. MACHINE IS IN VERY GOOD CONDITION. CHARLES ROSS & SON HAD RECONDITIONED KNEADER EXTRUDER.

2015 COLD JET AERO 40FP PORT. FULL PRESSURE DRY ICE CLEANING SYSTEM, 170 HOURS, S/N: 2A0290-G1-F, W/GUN & WANDS

1991 PCMC ECM-14 HIGH-SPEED ELECTRONIC CORE MACHINE S/N: 7294. INCLUDES UNWIND STAND, ADHESIVE APPLICATION UNIT, CORE WINDING UNIT, SERVO DRIVEN CUTOFF MODULE. STANDARD PRODUCT RANGE: CORE STOCK WIDTH 2.5" - 3.5"; CORE INSIDE DIA. RANGE 1" - 2"; CORE LENGTH RANGE 60" MINIMUM - UNLIMITED MAXIMUM CUTOFF. MAXIMUM WALL THICKNESS .17". PRODUCT SPECIFICATIONS: CORE STOCK THICKNESS .015. CORE STOCK WIDTH 3". CORE INSIDE DIA. 1.65". 1.65" ID MANDREL. WAS MAKING 102" LONG CORES. UNWIND STAND WILL ACCEPT 50" DIA. ROLLS OF PAPER ON 3" CORES. 2 PLIES. (2) UNWINDS ARE BEING UNWOUND AT THE SAME TIME. GUARANTEES: SPEED-BASED USING GOOD QUALITY LIGHTWEIGHT CORE STOCK & HEATED ADHESIVE, 350 FPM OF FINISHED CORE, GUARANTEED 400 FPM DESIGN SPEED OR 60 CORES PER MINUTE, WHICHEVER COMES FIRST. CUTOFF ACCURACY: SET LENGTH +/- .0625". LEFT-HAND MACHINE. CUTOFF TO THE LEFT WHEN VIEWED FROM OPERATOR POSITION. TOSHIBA AC CONTROLLER. (2) NEW AC DRIVE MOTORS; 5 HP EACH ON CORE WINDING UNIT. SET UP ON 208/230/460 VOLTAGE, 3 PHASE, 50 OR 60 CYCLE. TOTAL OF (4) UNWIND POSITIONS. HAS 4-POSITION UNWIND WITH DRAG BELT BRAKING. STANDARD HEATED GLUE POT. AIR CYLINDER FOR TENSION BETWEEN WINDING DRUMS. SERVO CONTROLLED ELECTRONIC CUTOFF MODULE. SAW CUTOFF. IN OCTOBER 2013, ORIGINAL SERVO CORE CUTTER ELECTRICS & MOTORS WERE REPLACED DUE TO BEING OBSOLETE. THEY HAVE BEEN REPLACED WITH A NEW BALDOR SERVO MOTOR AND NEW BALDOR (ABB) SERVO AMPLIFIER. THE FRONT END CONTROL & OPERATOR INTERFACE HAVE BEEN REPLACED WITH A NEW CONTREX M-SHUTTLE CONTROL. ALL PROGRAMMING INFORMATION WILL BE SUPPLIED WITH THE MACHINE. NEW ELECTRICAL DRAWINGS WILL REFLECT THE WIRING CLEANUP & CHANGES. ALL TECHNICAL INFORMATION NOT DIRECTLY SUPPLIED IS DIRECTLY AVAILABLE WITH INTERNET ACCESS. COPY OF MANUAL INCLUDED. AIR MOTOR IS USED FOR CUTOFF SAW BLADE. UNIT WAS INLINE WITH PCMC 250 SERIES WINDER. OPERATING AT 2,500 FPM. HIGH-SPEED SERVO DRIVEN CORE MACHINE.

HYSTER H200E FORKLIFT, 20,000 LB., DUAL FRONT TIRES, READS 1200 HOURS S/N: B7L1935H

1980 STANFORD 142-HD DOCTOR MACHINE, REWINDER. CENTER REWINDER. S/N: 6804301. DESIGNED TO SALVAGE DOCTOR REJECTED OR PARTIALLY SPOILED ROLLS. THE 142 SERIES WILL UNWIND AND REWIND THE ROLLS THAT ARE TELESCOPED, UNEVENLY WOUND, PRINTED PARTIALLY OUT OF REGISTER OR REJECTED FOR OTHER REASONS. PAPERS, LAMINATED STOCKS, CARBONLESS PAPER, PRESSURE-SENSITIVE CARBON PAPER & FOIL LAMINATES CAN BE HANDLED ON A 142 SERIES DOCTOR. OPEN CANTILEVER SHAFT DESIGN. 4 MINIMUM WEB WIDTH. WEB SPEED IS LIMITED TO 1500 FEET PER MINUTE. MAXIMUM UNWIND ROLL DIAMETER, 40. MAXIMUM REWIND ROLL DIAMETER, 40. MAXIMUM ROLL WEIGHT, 350 LBS. AUTOMATIC WEB GUIDING & CONSTANT TENSION. REWIND IS CONSTANT TENSION CENTER REWIND. HEAVY-DUTY PNEUMATIC SHAFTS. TOP MOUNTED AIR-OPERATED RIDER ROLL PROVIDES UNIFORM ROLL DENSITY. RIDER ROLL RESTS ON TOP OF REWINDING ROLL. UPDATED DRIVE & MOTOR. TOSHIBA VARIABLE SPEED AC DRIVE WITH 10 HP VECTOR MOTOR, 230 VOLT, 3PHASE, 60 CYCLE. ELECTRIC PRE-DETERMINING COUNTER. VEEDER ROOT PRE-DETERMINED COUNTER; STOPS AT FOOTAGE. CONSTANT TENSION AIR BRAKE ASSEMBLY OPERATED THROUGH A COUNTER-BALANCED DANCER ROLL WHICH SENSES WEB TENSION AND CONTROLS THE UNWIND BRAKE AUTOMATICALLY. BRAKE IS AIR-COOLED, AIR-OPERATED. WEB GUIDING IS A FIFE AUTOMATIC WEB GUIDING, PNEUMATIC SENSOR. ANTI-FRICTION BALL BEARINGS. 3 AIR SHAFTS USED ON THE UNWIND AND REWIND POSITIONS. RECENTLY OVERHAULED.

2006 GRACO DL-3 3-PART MIXER/PUMPING SYSTEM. WAS USED TO MIX 2-PART SILICONE ADHESIVE. THE THIRD TANK/PUMP WAS NOT USED. SILICONE PARTS A & B WERE RATIO AT THE MIXING HEAD. LINES & TANKS WERE INSULATED AND TANKS HEATED. SERIAL # 7233. ALPHANUMERIC KEYPAD. FLOW RATE SET UP SCREEN, CALIBRATION SCREEN. MIXER HEAD. BALL VALVE. (3) COMPONENTS. MIX HEAD. B PUMP. C PUMP. A PUMP. COMPONENT A ORIFICE IS .01. COMPONENT B ORIFICE IS .01. COMPONENT C ORIFICE IS .04. HAS ALL ELECTRICS. (3) TANKS ARE HEATED. CTC PARKER TOUCHSCREEN. OMRON SYSMAC PLC. HAVE PROGRAM & MANUALS. DRIVES ARE INCLUDED. AC MOTORS, 460 VOLT. COMPUTER CONTROLLED. COMPLETE MIXING & DISPERSING SYSTEM. (3) PUMPS. (3) TANK ASSEMBLIES. HOSE ASSEMBLY. MIX HEAD.

2005 STRONG ROBINETTE 2000 FEEDER. HIGH DAILY PRODUCTION, DOUBLE-DECK FEEDER. HIGH SPEED CAPABILITY, 100 TO 150 BAGS PER MINUTE. TUBE STORAGE, UP TO TEN HANDS. HANDLES STACKS UP TO 5 HIGH. HANDLES FLAT OR GUSSETED TUBES. QUICK SIZE CHANGES. TUBE LENGTH RANGE, 16 TO 52 (41-132CM). TUBE WIDTH RANGE, 6 TO 30 (15-76CM). PRE-WIRED FOR 3 PHASE. ADJUSTABLE TIMING SWITCH FOR BOTTOMER INCLUDED. SELF-CONTAINED VACUUM SYSTEM. ABB VARIABLE SPEED AC DRIVE. MODEL ACS. 480 VOLT, 3 PHASE, 60 CYCLE. EMERSON 2 HP AC DRIVE. EACH DECK HAS ITS OWN VACUUM PUMP. MACHINE IS IN GOOD CONDITION

HYSTER FORTIS S120FTPRS LPG FORKLIFT, 9000 LB., 196.9" LIFT, TRUCK CAP. 12,000 LBS. S/N: G004V06102J

CAMERON 420 2-DRUM SURFACE REWIND, SINGLE SHAFT SLITTER REWINDER. S/N: L-7260. 42" DIAMETER REWIND. FRAMES ARE HEAVY-DUTY. 70" WIDE, 6.25" DIAMETER SOLID STEEL BEDROLLS. UPPER RIDER ROLL, 4.75" DIAMETER, STEEL WITH RUBBER COVERING ON UPPER RIDER ROLL; THIS ASSISTS WITH GRIPPING AND ENSURING TIGHTLY REWOUND ROLLS. RIDER ROLL NEEDS TO BE RE-COVERED WITH RUBBER. FINCOR MODEL 3130M DC VARIABLE SPEED DRIVE CONTROLLER. 460 VOLTAGE, 3 PHASE, 60 CYCLE. 40 HP G.E. DC DRIVE MOTOR. TWO MOUNT HOPE BOWED ROLLS. ONE BOWED ROLL IS MOUNTED BEFORE SLITTING SECTION, 65" WIDE. OTHER BOWED ROLL IS AFTER SLITTING IS DONE, 66" WIDE. BOTH ROLLS ARE MOUNT HOPE; THEY ASSIST WITH ROLL SEPARATION OF REWINDING ROLLS. TANGENTIAL / DRAW SHEAR. SET UP FOR 1.5 MINIMUM SLIT WIDTH. (24) MALE SHEAR CUT KNIVES & HOLDERS. (26) FEMALE BACK DRIVEN KNIVES. FORMER OWNER WAS SLITTING 3" WIDE SLITS ACROSS THE WEB. WAS SLITTING & REWINDING COATED PAPERS USED IN THE TAPE INDUSTRY. MOTOR USED FOR LIFTING UP THE RIDER ROLL. ASSISTS WITH CHANGE BETWEEN REWINDING OF ROLLS. BELTING IS USED FOR DRIVING BEDROLLS & RIDER ROLL SO THE MACHINE IS QUIETER. TWO 3" STEEL REWIND SHAFTS. TWO 1.375" DIAMETER REWIND SHAFTS. MAXIMUM SPEED OF MACHINE IS 2000 FEET PER MINUTE. UPPER RIDER ROLL IS COUNTER-WEIGHTED WHICH ASSISTS IN REWINDING TIGHTER ROLLS. REWIND SHAFT BEARING CARRIAGES RUN IN VERTICAL WAYS OF HARDENED AND GROUND STEEL. RIDER ROLL IS EQUIPPED WITH SELF-ALIGNING FLAT BELTS WHICH DRIVE EACH SIDE OF THE RIDING ROLL. HAS ADJUSTABLE TENSION EQUALIZING MECHANISM. PERMITS VARIATION OF THE RIDER ROLL TORQUE. BECAUSE OF BELTING, OPERATION IS SMOOTH, QUIET AND VIBRATIONLESS. UNWIND CAN BE PURCHASED FOR AN ADDITIONAL CHARGE OF $7,500 TO $25,000 FOR SHAFTLESS FLOOR PICKUP UNWIND. 420 SERIES IS A HIGH-SPEED SLITTER REWINDER FOR WINDING WAXED, GUMMED, COATED PAPERS, PAPER, BOARD, TUBE & CORE STOCK, TEXTILES, RUBBER, LAMINATIONS, TISSUE, TOWELING, NONWOVENS & NON-EXTENSIBLE PRODUCTS.

STANFORD 152 HD REVERSIBLE ROLL DOCTOR. CANTILEVERED UNWIND & REWIND SHAFTS. SHEAR CUT SLITTING. (2) MALE KNIFE HOLDERS. (5) FEMALE SHEAR KNIVES. MINIMUM SLIT WIDTH, 2.5. SPLICE SYSTEM. 3 AIR SHAFTS ON UNWIND & REWIND. MODEL 152 HD IS A REVERSIBLE ROLL DOCTOR. 40 DIAMETER ROLLS ON UNWIND & REWIND. 850 LB. ROLL WEIGHT. 1500 FEET PER MINUTE. UPDATED MODERN DRIVE, ALLEN BRADLEY POWERFLEX 755 DRIVE, 460 VOLTAGE. ABB 10 HP AC MOTOR. DURANT COUNTER WITH PRESET FOOTAGE STOP. FIFE 2-ROLL WEB GUIDING. ELECTRIC EYE CPD-01 CONTROLLER. AUTOMATIC EDGE GUIDING & AUTOMATIC TENSION CONTROL. AIR-OPERATED RIDER ROLLS ON BOTH UNWIND & REWIND. CAN CONTROL PRESSURE OF RIDER ROLLS TO PROVIDE UNIFORM DENSITY CONTROL. SINGLE MOTOR DRIVE. BOWED ROLL MOUNTED ON RIDER ROLL BEFORE PRODUCT IS REWOUND; HELPS WITH ROLL SEPARATION OF REWOUND ROLL. 4" TO 20" WIDE WEBS. REWIND PRINT IN OR OUT. EFFICIENT METHOD OF SPLICING & REMOVING DEFECTIVE PRINTING/SPLICES. REVERSING FEATURE REDUCES ROLL SALVAGING TIME BY UP TO 50 PERCENT. CAN SPLICE & REVERSE WIND TO MAINTAIN THE PRINT PATTERN. WIDE RANGE OF MATERIALS, NON-EXTENSIBLE FILMS, PAPER, FILM/FOIL LAMINATIONS, P/S LAMINATIONS. S/N: 5874702

BECK H-1 ROTARY SHEETER. SINGLE POSITION UNWIND FOR 70" OD MAXIMUM ROLLS. 2 STEEL SHAFT WITH 3 CHUCKS FOR 3 CORES. MANUAL EDGE GUIDE. SEGMENTED PULL-ROLL. 14" TO 71 CUTOFF RANGE VIA CONE GEAR SYSTEM. 3-ROLL DECURLER BAR. 55 WIDE IDLERS. 42 LONG TAPE SECTION WITH JOGGER TABLE WHICH HAS TOP TAPES. CAN CONTROL SPEED OF TAKEAWAY TAPES. DIFFERENT MATERIALS NEED DIFFERENT SPEEDS. 52 MAXIMUM SHEET LENGTH ON DELIVERY TABLE. HAS JOGGER TABLE. 7.5 HP AC MOTOR. 3 PHASE, 6 CYCLE, 208/220/460 VOLTAGE. INCLUDES ONE SPARE SHEETING KNIFE. TYPICALLY USED TO SHEET PAPER, LIGHT BOARD, NONWOVENS, FILM, & LAMINATIONS.

BECK H-1 ROTARY SHEETER. 4-POSITION UNWIND FOR 30" OD ROLLS. MANUAL EDGE GUIDE. TWO 3 AIR UNWIND SHAFTS. SEGMENTED PULL ROLL. 14 TO 71 CUTOFF RANGE VIA CONE GEAR SYSTEM. 3-ROLL DECURLER BAR. 45 WIDE IDLERS. 42 LONG TAPE SECTION. DELIVERING CUT SHEETS TO A JOGGER TABLE. 50 MAXIMUM SHEET LENGTH ON JOGGER TABLE. 300 FEET PER MINUTE. ADJUSTABLE TAPE SPEED. CAN VARY THE SPEED OF TAKE-AWAY TAPES WHICH IS USED FOR DIFFERENT PRODUCTS. VEEDER ROOT COUNTER. PAPER TURNOVER GUIDES. VARIABLE SPEED DRIVE MOTOR; HAS BEEN UPDATED. RELIANCE GV-3000 AC DRIVE. 460 VOLTAGE, 60 CYCLE. RELIANCE 5 HP AC MOTOR. TYPICALLY USED TO SHEET PAPER, LIGHT BOARD, NONWOVENS, FILM & LAMINATIONS. S/N: 1452

NORTHERN ENGRAVING COMPOSITE ROLL TO STEEL ROLL EMBOSSING SYSTEM. S/N: 19749 50 HP AC VARIABLE SPEED MARATHON MANUFACTURED MOTOR. SET UP FOR 230/460 VOLTAGE. NO DRIVE FOR MOTOR. 68 WEB WIDTH. 68 WIDE STEEL ROLL. 10.5 DIAMETER NORTHERN ENGRAVING MANUFACTURED STEEL EMBOSS ROLL, SERIAL # NG4023706-M800 650. RUBBER / COMPOSITE ROLL, 71 WIDE, 12.5 DIAMETER. RUBBER / COMPOSITE ROLL IS STATIONARY. RUBBER / COMPOSITE ROLL IS DRIVEN. RUBBER / COMPOSITE ROLL IS BOTTOM ROLL. STEEL ROLL IS ON TOP, AIR LOADED INTO THE RUBBER ROLL. MECHANICAL SCREW ADJUSTMENT TO ADJUST THE GAP BETWEEN THE TWO ROLLS. RUBBER ROLL HAS SQUARING ADJUSTMENT. 84.5 WIDTH BETWEEN FRAMES. 3.25 THICK EMBOSSER FRAMES. EMERGENCY STOP. 9 WIDE, 8.5 HIGH, 3.25 WIDE BEARING BLOCK. MOUNT HOPE BOWED ROLL WHICH CAN BE DRIVEN. THIS EMBOSSER WAS INLINE WITH HIGH-SPEED HAND TOWEL REWINDER. HAND TOWEL USED IN GAS STATIONS. OPERATING AT 1500 FEET PER MINUTE. EMBOSSING ROLL, STEEL ROLL IS IN VERY GOOD CONDITION.

MONTALVO BRAKES. APPROXIMATELY 4 COMPLETE WITH SAFETY CHUCKS AND MANY OTHER PARTS

1985 BECK HF ROTARY SHEETER (5) POSITION UNWIND. MANUAL SKEW ADJUSTMENT. MANUAL EDGE GUIDING, APPROXIMATELY +/- 2. 3 ID UNWIND SHAFTS. 26 DIAMETER ROLLS. NEXT INLINE IS 4-ROLL SEPARATOR. NEXT IS RAZOR SLITTING SECTION. INCLUDES TWO RAZOR KNIVES. UPDATED MOTOR, DRIVE. 5 HP AC MARATHON MOTOR, VARIABLE SPEED. 230 VOLT, 3 PHASE, 60 CYCLE. DURAPULSE AC VARIABLE SPEED DRIVE. AGE OF DRIVE MOTOR, 2012. VEEDER ROOT COUNTER WITH PRESET; TURNS MACHINE OFF ONCE IT REACHES PRESET COUNT. TOP & BOTTOM TAPE SECTION. BOTTOM TAPE SECTION HAS PIV TO VARY THE SPEED. 72 CUTOFF KNIFE. SET UP WITH FINGERS WHICH ALLOWS PRODUCTS TO BE CONTROLLED FROM THE POINT AT WHICH IT HAS BEEN SHEETED TO THE JOGGER DELIVERY FINGERS SYSTEMS. TYPICALLY USED FOR LIMP MATERIALS, LIGHT FILMS, NONWOVENS, GAUZE, FABRICS, ANY MATERIAL WHICH NEEDS TO BE CONTROLLED FROM THE POINT AT WHICH IT IS SHEETED TO THE POINT AT WHICH IT GOES TO THE DELIVERY SECTION. CAN DEACTIVATE, DISCONNECT FINGER SYSTEM. JOGGER DELIVERY. MAXIMUM 6 PILE HEIGHT. 15 TO 72 CUTOFF. JOGGER TABLE WILL ACCEPT 72 LONG PRODUCT. THE MACHINE WAS MOST RECENTLY SHEETING FILMS USED IN THE MEDICAL AND ELECTRONICS INDUSTRY. TYPICAL OPERATING SPEED, UP TO 200 FEET PER MINUTE. CUTOFF IS CHANGED WITH CONE GEAR SYSTEM. HAS STEPLESS FEED WHICH ALLOWS THE CUTOFF TO BE VARIABLE WITHIN THE 15 TO 72 CUTOFF RANGE. TAPE SECTION HAS VARIABLE SPEED AC DRIVE, SECO, 2 HP; ALLOWS YOU TO VARY THE SPEED OF THE TAKEAWAY TAPES DEPENDING ON WHAT THE MATERIAL IS THAT YOU ARE SHEETING. PNEUMATIC FEED ROLLS. SIMCO STATIC ELIMINATOR. MOTOR CONTROL ON JOGGERS. THIS MACHINE CAN BE USED FOR MANY DIFFERENT PRODUCTS, NONWOVENS, PAPERS, FABRICS, FILMS, PAPER BOARD. S/N: 2556

JOHNSTONE 10 FSRS SLITTER REWINDER, 2-DRUM SURFACE REWIND, HEAVY-DUTY, SINGLE SHAFT, SLITTING & REWINDING MACHINE. S/N: 17065A. 50" DIAMETER REWIND. SINGLE POSITION DETACHED UNWIND STAND, JOHNSTONE MODEL 34, SERIAL # 32645. SHAFTLESS OPERATION. CONSTANT TENSION SYSTEM DANCER; CONTROLS BRAKES AUTOMATICALLY. 64 DIAMETER ROLLS OF MATERIAL ON UNWIND. DUAL JOHNSTONE BRAKES & AUTOMATIC TENSION. 3 DOUBLE E CORE CHUCKS ON UNWIND. FIFE AUTOMATIC EDGE GUIDING; AUTOMATICALLY MOVES UNWIND LEFT & RIGHT +/- 3" OF TRAVEL. PNEUMATIC SENSOR. ROLL LIFT SYSTEM; LIFTS ROLLS UP TO CHUCKS. SELF-CENTERING. HAS PUSH-BUTTON TO OPEN & CLOSE SIDES OF UNWIND. HAS SKEW ROLL MOUNTED ON UNWIND. SHEAR CUT SLITTING. (15) FEMALE SHEAR KNIVES. (10) MALE SHEAR KNIVES. MALE / FEMALE KNIVES / SHAFTS DRIVEN. TANGENTIAL SHEAR. TWO SETS OF CIRCULAR CUTTERS MOUNTED ON DRIVEN PARALLEL SHAFTS. CUT CLEANING & ACCURATELY, KEEPING DUST TO A MINIMUM. 3" ID SHEAR SHAFTS, WHICH ARE DRIVEN. JOHNSTON ROLL SEPARATION SYSTEM AFTER SLITTING SECTION, BEFORE REWINDING. BOWED BAR HELPS WITH ROLL SEPARATION. 2 MINIMUM SLIT WIDTH. TYPICAL OPERATING SPEED 2000 FEET PER MINUTE. MECHANICAL SPEED, 2500 FEET PER MINUTE. 74 WIDE BEDROLLS. SMOOTH BEDROLLS. 9.5 DIAMETER BEDROLLS. IDLERS ARE 9.5" DIAMETER, 74" WIDE. UPPER RIDER ROLL IS DRIVEN, 5.375" DIAMETER, 74" WIDE. UPPER RIDER ROLL. HAS COUNTERWEIGHT SYSTEM TO CONTROL AMOUNT OF PRESSURE RIDER ROLL APPLIES TO THE REWINDING ROLL; HELPS TO REWIND TIGHT/SOFT ROLLS. PUSH-BUTTON CONTROL TO LIFT RIDER ROLL UP. LOUIS ALLIS DYNAMATIC ADJUSTO SPEED DRIVE CLUTCH. DRIVE, 50 HP AC MOTOR, 230 VOLT, 60 CYCLE. LOUIS ALLIS DRIVE & MOTOR, VARIABLE SPEED. HAS BEEN SLITTING & REWINDING PAPER. ONE 3" AIR REWIND SHAFT. CAPABLE OF SLITTING LIGHT PAPERS TO 40 PT. BOARD. LARGER DIAMETER BEDROLLS. WINDING DRUMS HELP WHEN SLITTING BOARD & ALLOW HIGH-SPEED OPERATION. LARGER DIAMETER IDLERS ALSO HELP WHEN SLITTING BOARD. SLITS ALL WEIGHTS & GRADES OF PAPER & BOARD CLEANLY & PRECISELY. MACHINE WAS RECENTLY OVERHAULED.

HOLWEG RS-2 ROTO SIMPLEX PERFORATOR CUTOFF, VARIABLE SIZE PAPER BAG MACHINE TO MANUFACTURE FLAT & GUSSETED BAGS. MACHINE # DA188. 10 PITCH. PERFORATOR CUTOFF. OPERATES WITH WIDE RANGE OF MATERIALS INCLUDING TISSUE, DRY OR WAXED PAPER, GLASSINE, BOND, SULFITE OR KRAFT PAPERS UP TO 65 LBS. & PAPER / FOIL LAMINATIONS. HAS COLD GLUE SEAM POT & COLD GLUE BOTTOM GLUE POT. SINGLE POSITION UNWIND, 50 DIAMETER, 3 CORE. BRAKING & SIDE SHIFTING OF UNWINDING ROLL. VARIABLE SPEED DRIVE. DESIGNED FOR VERY HIGH SPEED OPERATION. 2.75 15 WIDE BAGS. 5.75 26 CUTOFF. 30 WIDE PAPER. EITHER CENTER OR SIDE SEAM GLUING. PRODUCTION FOR FLAT BAGS, 200 TO 300 BAGS PER MINUTE; DEPENDENT UPON BAG LENGTH, OPERATORS SKILL, GLUE, PAPER & ENVIRONMENT MACHINE IS SET UP IN. MACHINE HAS 4 WIDE FORMER IN MACHINE. MECHANICAL COUNTER. 15 WIDE DRUM; (4) STATIONS ON DRUM. 17 BETWEEN STATIONS. STANDARD VERTICAL DELIVERY. UPDATED AC VARIABLE SPEED DRIVE & MOTOR. MITSUBISHI FREQROL 2300 CONTROLLER AND TOSHIBA 15 HP AC MOTOR, 460 VOLTAGE, 3 PHASE, 60 CYCLE. MACHINE IS IN GOOD MECHANICAL CONDITION.

ARROW 325-24 SLITTER REWINDER NARROW WIDTH SLITTING, MINIMUM GAP REWIND, CENTER REWIND, CANTILEVERED REWIND SHAFTS, DUPLEX SLITTER REWINDER. S/N: 9214. MINIMUM GAP CENTER REWIND. MOVEABLE REWIND SHAFTS WHICH ALLOW FOR ADJUSTABLE MINIMUM GAP REWINDING CAPABILITY WHICH ALLOWS FOR NARROW SLITS. .25 & .5 SLIT WIDTHS USING CORRECT SLITTING KNIVES. CANTILEVERED REWIND SHAFTS. EACH REWIND STATION IS DRIVEN THROUGH A SENSITIVE SLIP CLUTCH. CANTILEVERED REWIND SHAFT MOUNTED ON A PIVOTED BRACKET TO PERMIT LOCATION OF THE REWIND IN ORDER TO MINIMIZE THE DRAW DISTANCE BETWEEN REWINDING ROLL AND IDLER ROLL. THIS ALLOWS NARROW SLITS TO BE MADE. ATTACHED UNWIND, 24 DIAMETER ROLL. ONE 3 AIR UNWIND SHAFT. AIR BRAKE. ACCUGUIDE AUTOMATIC EDGE GUIDING SYSTEM TO MOVE UNWINDING ROLL LEFT & RIGHT +/- 4. ELECTRIC EYE SENSOR. RAZOR SLITTING. SLIT IN AIR. SHEAR CUT SLITTING. (15) MALE SHEAR CUT KNIVES. .25 SLIT WIDTH USING RAZOR SLITTING. DRIVEN FEMALE SHEAR CUT KNIFE SHAFT. (25) FEMALE KNIVES. WRAP SHEAR. SHEAR KNIVES ALLOW 1.5 MINIMUM SLIT. 3 GOLDEN ROD AIR REWIND SHAFTS. LOCKED CORE REWINDING. EACH REWIND POSITION HAS ITS OWN AIR CLUTCH. 24 DIAMETER REWIND. 5 HP AC BALDOR MOTOR WITH CONTROL TECHNIQUES VARIABLE SPEED AC DRIVE, UNIDRIVE M200, 480 VOLTAGE, 60 CYCLE, 3 PHASE. UPGRADED DRIVE & MOTOR. 26 WIDE ROLLS. INCLUDES SLEEVES FOR SCORING ROLL. CAN USE FEMALE KNIFE SHAFT. INSTALL SLEEVES AND CAN DO SCORE CUTTING. WHEN USING SCORE CUT SLITTING. .5 MINIMUM SLIT WIDTH. NO MALE SCORE CUT KNIVES. MANUALLY CONTROL MINIMUM GAP. REWIND ARMS / SHAFTS MOVE OUT AS THE DIAMETER OF THE REWINDING ROLL INCREASES. DISTANCE FROM IDLER ROLL TO REWINDING ROLLS KEPT TO A MINIMUM. MECHANICAL COUNTER. 400 FEET PER MINUTE. MACHINE IS CAPABLE OF SLITTING & REWINDING PRESSURE-SENSITIVE TAPES, LABEL STOCK, LAMINATIONS, PAPER, TEXTILE PRODUCTS, NONWOVENS, FILMS, FOILS, LIGHT & HEAVY-GAUGE FILMS. CANTILEVERED REWIND SHAFTS ASSIST WITH QUICK LOADING & UNLOADING OF ROLLS. 500 FEET PER MINUTE WEB SPEED.

ECLIPSE LF350 DIGITALLY PRINTED ROLLS, LABEL CUTTING & FINISHING SYSTEM. S/N: 15105523. HAS CUTTING & READING FOR DIFFERENT SHAPES. LABEL LENGTHS, UP TO 850MM. CUTTING DIES ARE NOT REQUIRED. MAXIMUM WEB WIDTH, 13.7. LINEAR CUT SPEED DEPENDENT ON GRAPHICS. CUT SPEEDS, 800 400 AXIAL. CUT TYPE, SINGLE HEAD DRAGGED KNIFE AND TANGENTIAL EMULATION. SINGLE POINT REGISTRATION MARK. CUTTING ABILITY, BOTH PRINTED & UNPRINTED MEDIA. MAXIMUM LABEL LENGTH REPEAT, 31.5. UNSUPPORTED LAMINATING ROLL. SUPPORTED REWIND. CANTILEVERED SHAFTS. MAXIMUM ROLL DIAMETER, 17.7, 3 CORES. HAS WASTE MATRIX, REMOVAL & REWIND. DUAL REVERSIBLE CENTER REWINDERS. FINISHED LABEL REWIND. 220 VOLT, SINGLE PHASE, 50 OR 60 CYCLE. WIDTH OF IDLER ROLLS, 14. HAS NIP ROLL FOR LAMINATING.

CATERPILLAR GC40KSTR LPG FORKLIFT, 183" LIFT, 5100 LBS., 9450 HOURS, 3-STAGE MAST S/N: AT87A02009

WINDMOLLER & HOLSCHER QMS 992 4-COLOR INLINE FLEXOGRAPHIC PRINTING PRESS. 37" WIDE PRINT CYLINDERS. MOST RECENTLY PRINTING KRAFT PAPER FOR PAPER BAGS. 36" WEB WIDTH, 6" DIAMETER. 38" WIDE IMPRESSION ROLL, 5" DIAMETER. 32" WIDE CHROME ANILOX ROLLS. 9 TO 31 REPEAT. 10 PITCH. ALSO REFERRED TO AS ALINA X TAILEND PRINTER. 30" DISTANCE BETWEEN COLORS. UNIVERSAL DRIVE SHAFT WITH BEVEL GEARS WHICH DRIVE THE INFEED ROLLERS. PRINTER CAN BE PUT INLINE WITH PAPER BAG MACHINE, SLITTER REWINDER, SHEETER, LAMINATOR & MANY OTHER PROCESSES. DESIGNED WITH CENTRAL BULL GEAR FOR GOOD REGISTER PRINTING. TYPICAL OPERATING SPEED, 750 FEET PER MINUTE. WAS PRINTING WITH WATER-BASED INKS. CAPABLE OF PRINTING ON PAPER AND OTHER SUBSTRATES FROM 8.25 TO 82 LB. PLATE CYLINDER LIFT. CONSTANT ROTATION OF ANILOX ROLLS DONE WHEN MACHINE IS STOPPED. AC MOTOR DRIVES ANILOX ROLLS. HEAVY-DUTY SIDE FRAMES. HIGH-SPEED OPERATION. (4) INK PANS. PRECISION REGISTER ADJUSTMENTS ACROSS THE WEB & IN TRAVELING DIRECTION. BOTH LONGITUDINAL & LATERAL REGISTRATION. REGISTRATION CONTROLS ALLOW ADJUSTMENTS TO BE MADE WHILE PRINTER IS RUNNING. HAS ADJUSTMENT TO SHIFT PRINTER LEFT & RIGHT, +/- 2. CHANGE GEAR SYSTEM. APPROXIMATELY (2) SPARE CHROME ANILOX ROLLS. CHROME ANILOX ROLLS; 2 OF 4 RECENTLY REPLACED. (4) 6.35 PRINT CYLINDER LENGTH, 66-TOOTH. (4) PRINT CYLINDERS, LENGTH 7.35, 76-TOOTH. (4) PRINT CYLINDERS, LENGTH 8.55, 88-TOOTH. WAS INLINE WITH PAPER BAG MACHINE. S/N: 11001

CATERPILLAR T80D FORKLIFT, 188" LIFT, 7800 LB., 7094 HOURS, TOW LIFT-CASCADE MAST, NO FORKS, WAS USED W/CLAMP ATTACHMENT S/N: 5KBO4924

1996 ZINK 3-ROLL GRAVURE COATING STATION S/N: 4-401-10072. TOP ROLL IS SMOOTH STEEL, CHROME COVERED. MIDDLE ROLL IS RUBBER-COVERED. BOTTOM ROLL IS STEEL GRAVURE. BOTTOM ROLL IS STATIONARY. TOP & MIDDLE ROLLS ARE AIR LOADED. GAP ADJUSTMENTS FOR THE TOP & MIDDLE ROLLS. BOTTOM GRAVURE ROLL HAS HARRIS & BRUNO ENCLOSED DOCTOR BLADE ASSEMBLY, SERIAL # HB1823. ONE SPARE DOCTOR BLADE ASSEMBLY. INCLUDES (3) MOTORS. MOTOR STAND & GEARBOXES. COATING HEAD MOTORS MOUNTED ON SEPARATE DRIVE STAND. INDEPENDENTLY DRIVEN ROLLS. CAN OPERATE AS DIRECT / DIFFERENTIAL / REVERSE / OFFSET STATION; EACH ROLL IS INDEPENDENTLY DRIVEN. WAS USED FOR COATING ON FILMS. 4" THICK FRAME. STAINLESS STEEL DRIP PANS. ONE 75 HP BLACK CLAWSON DC DRIVE MOTOR. TWO BLACK CLAWSON 25 HP DC MOTORS. GEARBOXES INLINE WITH MOTORS. ONE SPARE DOCTOR BLADE. 89" TOP ROLL, CHROME-COVERED, 16" DIAMETER, AIR-LOADED. 89" RUBBER-COVERED MIDDLE ROLL, 13.875" DIAMETER, AIR-LOADED. 89" GRAVURE BOTTOM ROLL, 16" DIAMETER, STATIONARY. TWO SPARE DRIP PANS. 89" WIDE AIR-LOADED DANCER. WAS OPERATING AT 1500 FEET PER MINUTE. IN GOOD MECHANICAL CONDITION. WATER-BASED COATINGS APPLIED.

KIDDER CW CENTER REWIND, SINGLE SHAFT, SLITTER REWINDER. 40" DIA. UNWIND. 40" DIA. REWIND. SINGLE MOTOR DRIVE. SHEAR & SCORE CUT SLITTING. MOUNT HOPE AUTOMATIC TENSION CONTROL WITH TENSION ROLL. FIFE AUTOMATIC EDGE GUIDING ON UNWIND STAND +/- 3". SINGLE MOTOR DRIVE. TWO AIR-LOADED SCORE CUT KNIVES. HAS BEEN SLITTING & REWINDING PAPER & NON-EXTENSIBLE PRODUCTS. 2000 FPM. CW DESIGNED TO SLIT 5.5 LB. CARBON TISSUE TO 200 LB. TAG STOCK. CAN SLIT LAMINATIONS, HEAVY FILM, COATED PAPERS. SCORE SLITTING CAN ALSO BE USED TO PERFORATE THE WEB. MOTORTRONICS MODEL K PLUS CONTROLLER. VARIABLE SPEED AC DRIVE, APPROX. 10 YEARS OLD. 460 VOLTAGE, 3 PHASE, 60 CYCLE. 20 HP TECO MOTOR, AC MOTOR. TAPER TENSION. DRIVE SLOWS DOWN REWINDING ROLL AS REWINDING ROLL DIAMETER INCREASES. IDLERS IN MACHINE ARE 44" WIDE, 4" DIAMETER STEEL IDLERS. ONE 3" AIR UNWIND SHAFT. ONE 3" AIR REWIND SHAFT. ATTACHED UNWIND. MANUAL SKEW ADJUSTMENT. 12" DIAMETER TIDLAND AIR BRAKE. SHEAR CUT BOTTOM FEMALE KNIVES. (46) KNIVES. (8) MALE SHEAR CUT KNIVES & HOLDERS. FEMALE KNIVES ARE .75" WIDE. MALE SHEAR KNIVES WITH HOLDER ARE 2" WIDE; SO 2.5" MINIMUM SLIT WIDTH. RED LION COUNTER. COMPACT, LOW PROFILE DESIGN. EASY TO OPERATE. THIS MACHINE HAS BEEN REFURBISHED; MANY NEW BEARINGS INSTALLED.

HYSTER S150A LPG FORKLIFT, 15,000 LB., 99.5" LIFT S/N: A024D02918V

WINDMOLLER & HOLSCHER ALINA X 3-COLOR, FLEXOGRAPHIC INLINE TAILEND PRINTING PRESS S/N: 7252. SOME PARTS TO THE FOURTH PRINT STATION. 32 WEB WIDTH. 31 PRINT WIDTH. 32.5 RUBBER ROLL. 32.5 ANILOX ROLLS. 32.5 IMPRESSION CYLINDERS. ALINA X30 FLEXOGRAPHIC TAILEND PRINTER. 30 DRYING DISTANCE BETWEEN EACH COLOR. 10 PITCH GEARING. DESIGNED WITH CENTRAL BULLGEAR WHICH HELPS TO ASSURE QUALITY PRINTING & GOOD REGISTER CONTROL. TYPICAL OPERATING SPEED, 600 FEET PER MINUTE. SPEED DEPENDS UPON MATERIAL & DRYING CAPABILITY OF THE INK USED & SUBSTRATE PRINTED. MOST RECENTLY PRINTING WITH WATER-BASED INKS. CYLINDER THROWOFF WHICH IS DONE MANUALLY. SOLID CONSTRUCTION & HEAVY-DUTY SIDE FRAMES ASSURE VIBRATIONLESS, HIGH-SPEED OPERATION & QUALITY PRINTING. SHAFT DRIVES THE PRINTER. MANUAL 360 DEGREE REGISTRATION CONTROLS. PRINTING PLATE CYLINDER IS MOVED FROM SIDE-TO-SIDE MANUALLY TO ADJUST FOR CROSS REGISTER. BOTH ADJUSTMENTS ARE MADE WHILE THE PRESS IS RUNNING. TWO 8.4 DIAMETER, THREE 6.8 DIAMETER, FIVE 5 DIAMETER & THREE 4.7 DIAMETER PRINT CYLINDERS. 6 DIAMETER IMPRESSION CYLINDERS. 5 DIAMETER ANILOX ROLLS. 5 DIAMETER RUBBER ROLLS. MANUAL SIDE SHIFTING OF PRINTER LEFT & RIGHT 4. THIS PRINTER CAN BE USED WITH PAPER BAG MACHINES, POLY BAG MACHINES, LAMINATORS, SHEETERS, ETC. MOST RECENTLY WAS INLINE WITH PAPER BAG MACHINE. HAS CHANGE GEAR SYSTEM. REFURBISHED RECENTLY

1980 DUSENBERY 260 FS DUPLEX CENTER SURFACE REWIND SLITTING & REWINDING MACHINE S/N: 57961. 24" MAXIMUM REWIND ROLL DIA. 1500 FPM. 2.25" MINIMUM SLIT WIDTH. UPDATED EMT. SHEAR CUT SLITTING. TANGENTIAL SHEAR CUT. AIR FEMALE KNIFE SHAFT, DRIVEN. (15) FEMALE KNIVES. (25) AIR-LOADED MALE KNIVES. CAN EASILY RAZOR SLIT IN AIR. MALE KNIFE BAR CAN HAVE RAZOR HOLDERS INSTALLED. DETACHED SINGLE POSITION SHAFTLESS UNWIND, MODEL 824ND, 60" ROLL DIA. MAXIMUM 80" CORE LENGTH. AUTOMATIC EDGE GUIDE. AUTOMATIC TENSION CONTROL. AIR-COOLED, AIR-OPERATED BRAKING SYSTEM. AGE 1981. 6", 8", 10" & 12" CORE CHUCKS. 20" MONTALVO BRAKE WITH MONTALVO SYSTEM 3000 TENSION CONTROLLER WITH LOAD CELLS. E&L DCS ELECTRIC EDGE GUIDE; +/- 3" OF MOVEMENT. ALL CONTROLS MOUNTED ON UNWIND. 3 MOTOR DRIVE, DC VARIABLE SPEED. (2) 15 HP MOTORS; ONE ON EACH REWIND POSITION. 20 HP MOTOR; DRIVES PULL ROLLS & SURFACE BEDROLL. RELIANCE MOTORS & CONTROLLERS. DYNAPAR MAX COUNT COUNTER. PRECISION TRIM CHOPPER WITH 1 HP MOTOR INCLUDED. UPDATED BRAKE, TENSION SYSTEM, EDGE GUIDE, SHEAR CUT SECTION. (3) 3 DIFFERENTIAL REWIND SHAFTS. 1-ZONE, AIR-LOADED DIFFERENTIAL REWIND. AIR-OPERATED SINGLE DIFFERENTIAL REWIND TENSION CONTROL. REWIND ARMS WITH ADJUSTABLE AIR CYLINDERS FOR DOWN PRESSURE CONTROL USING BALANCING PRESSURE SYSTEM. PLAIN STEEL WINDING DRUMS. 230 VOLT, 3 PHASE, 60 CYCLE. RELIANCE 3-MOTOR SCR DRIVE FOR SLIP CORE OR LOCKED CORE WINDING. SLOW DOWN SYSTEM USING REWIND ARM POSITION TO SENSE DIAMETER OF REWINDING ROLL. HAS BEEN SLITTING & REWINDING FLEXIBLE PACKAGING MATERIALS, LAMINATIONS.

1992 BRETTING 86 EMBOSSING SYSTEM WITH MATCHED STEEL-TO-STEEL EMBOSSING ROLLS. SERIAL # OF EMBOSSING STAND, 4555-92. MATCHED STEEL-TO-STEEL ROLLS. STANDARD DIMPLE PATTERN. USED FOR INDUSTRIAL HAND TOWELS. SERIAL # OF ONE OF THE TWO EMBOSSING ROLLS IS GREEN BAY EMBOSSING 98-3262-04-4860 10-5984A. 87 FACE WIDTH EMBOSS ROLL. 12 DIAMETER. EACH EMBOSS ROLL HAS A DRIVEN BRISTLE ROLL. TOP ROLL IS STATIONARY. BOTTOM ROLL IS AIR-LOADED INTO THE TOP ROLL. ELECTRIC MOTORS TO ADJUST THE GAP BETWEEN THE TWO ROLLS. SQUARING ADJUSTMENT TO SQUARE THE TWO ROLLS. SPRAY BAR & NOZZLES FOR MISTING SYSTEM. 101 BETWEEN THE FRAMES. 2.5 THICK FRAMES. 8 TALL, 9 WIDE, 4.5 THICK BEARING BLOCKS. BOWED ROLL WHICH CAN BE DRIVEN. DANCER INLINE; CONTROLS SPEED OF EMBOSSER. FAIRCHILD VARICHAIN SPECON PIV. LINESHAFT DRIVES THE FAIRCHILD, WHICH DRIVES THE EMBOSSING ROLLS. TOP ROLL IS STATIONARY. TOP ROLL IS ROLL THAT IS SQUARED. BOTTOM ROLL IS AIR-LOADED UP INTO THE TOP ROLL. GEARING BETWEEN THE TWO ROLLS. WAS OPERATING AT UP TO 1500 FEET PER MINUTE. ROLLS ARE IN VERY GOOD CONDITION. MOST RECENTLY BEING USED TO EMBOSS KRAFT HAND TOWEL PRODUCTS. 1:1 RATIO OF EMBOSS ROLLS. ROLLS & EMBOSSER WERE REFURBISHED IN 2012; FORMER OWNER INDICATED THAT APPROXIMATELY $80,000 WAS SPENT ON REFURBISHING AT THAT TIME. CAN BE USED FOR TISSUE, TOWELING, NONWOVENS & PAPERS.

1990 PERINI ECHO RODENA AUTOMATIC REWINDER. SURFACE REWINDER. SINGLE POSITION UNWIND, BELT DRIVEN. 60 DIAMETER. (4) 2.25 REWIND SHAFTS. 110 IDLERS & ROLLS THROUGHOUT THE MACHINE. STEEL-TO-RUBBER EMBOSSER. STANDARD DIMPLE PATTERN. (2) SPARE RUBBER ROLLS. PERF SECTION WITH (4) BLADES, 3.74 8.86 PERFORATION DISTANCE. (27) AIR-LOADED PLY BONDERS. EDGE EMBOSSING. FEMALE SHEAR CUT KNIFE SECTION. NO MALE SHEAR CUT KNIVES. RIDER ROLL. AUTOMATIC TAIL CUTTING & GLUING, TAIL SEALING. CORE HOPPER, CORE CUTTING SYSTEM. AUTOMATIC LOADING OF CORES ONTO REWIND SHAFTS. AUTOMATIC STRIPPING OF FINISHED ROLLS. EATON IDT PANELMATE SCREEN. (2) ALLEN BRADLEY SLC500 PLCS. DC VARIABLE SPEED DRIVE & MOTOR, 45 KW. 380 VOLT, 3 PHASE, 60 CYCLE. 4.8 TO 24 DIAMETER REWIND. 120-600MM LOG DIAMETER. MANDREL SIZE CAPABILITY, 1.5 TO 3.25. UP TO 400 METERS PER MINUTE. MACHINE HAD BEEN MANUFACTURING JUMBO ROLLS OF TOILET TISSUE. IS CAPABLE OF REWINDING PAPER FOR MEDICAL, INDUSTRIAL WIPES, HAND TOWELS, CENTER PULLS, NONWOVENS PRODUCTS, 1 & 2-PLY TISSUES. MACHINE IS OUT OF OPERATION; FORMER OWNER WAS NOT USING THE CORE RECUTTING NOR SLITTING INLINE. THEY WERE REWINDING FULL LENGTH LOGS, WHICH WERE THEN CONVEYORED TO LARGE DIAMETER LOGSAW. WITHOUT SLITTING CORES AND SLITTING PRODUCT, MACHINE CAN GO FASTER. IN FAIR MECHANICAL CONDITION.

W&H MATADOR MODEL 26 STRIKER BAR CUTOFF, MODEL CD, F&S, VARIABLE SIZE PAPER BAG MACHINE. BAG WIDTH, 2 TO 8.25. CUTOFF LENGTH, 4 TO 18.875. TYPICAL SPEED, 400 BAGS PER MINUTE, DEPENDENT UPON PAPER, GLUE, IF PRINTING, OPERATOR & ENVIRONMENT. UNWIND TO ACCOMMODATE 36 OD ROLL. ONE 3 UNWIND SHAFT. MANUAL SIDE SHIFTING. COLD GLUE FOR SEAM & BOTTOM GLUE POT. ONE 8.25 WIDE GUSSETED FORMER. THREE EXTRA FORMERS, 4", 5.5" & 6". DELIVERY DRUM, 9 FACE WIDTH. (4) GRIPPING STATIONS AROUND THE DRUM. MECHANICAL COUNTER. STANDARD TABLE VERTICAL DELIVERY. 10 PITCH GEARING. VARIABLE SPEED DRIVE. BOSTON GEAR DC MOTOR CONTROL, MODEL RATIOTROL, 7.5 HP. DRIVE SET UP ON 230 VOLTAGE. RELIANCE DC 7.5 HP MOTOR. MAXIMUM WEB WIDTH, 28.5. SINGLE POSITION ATTACHED UNWIND. MANUAL SIDE SHIFTING. MANUAL ADJUSTMENT OF THE BRAKING. HAS MANUALLY ADJUSTED REGISTER ROLL TO REGISTER PRINT TO WEB. STRIKER BAR CUTOFF. 20 LONG DELIVERY TABLE. MACHINE IS IN GOOD MECHANICAL CONDITION. HAS BEEN RECENTLY OVERHAULED.

GOEBEL PRACTICA MODEL H3 1000 SURFACE REWIND SLITTER REWINDER FOR HIGH-SPEED PRODUCTION OF ROLLS. HAS BEEN SET UP AS A SHAFTLESS REWINDER. CAN OPERATE AS SHAFTED REWIND BY PURCHASING REWIND SHAFTS. FORMER OWNER WAS REWINDING 3 ID PRODUCT SHAFTLESS; IS ADJUSTABLE WIDTH. CAN HANDLE 1 ID ON REWIND. 2-DRUM SURFACE REWIND. SEMI-AUTOMATIC OPERATION. ATTACHED UNWIND. 40 DIAMETER ROLLS OF MATERIAL. 3 AIR SHAFT. UNWIND EQUIPPED WITH GOEBEL FRICTION-TYPE BRAKE, WHICH IS CONTROLLED BY A DANCER, WHICH PROVIDES AUTOMATIC TENSION CONTROL. MANUAL SKEW ADJUSTMENT. AUTOMATIC EDGE GUIDING OF UNWIND +/- 2. FIFE EDGE GUIDE. UPPER RIDER ROLL IS NOT DRIVEN. PRODUCT THAT WAS BEING REREELED WAS A COATED PAPER. IS CAPABLE OF REWINDING NON-EXTENSIBLE PRODUCTS. MOTORIZED RIDER ROLL LIFT. DYNAPAR COUNTER PRESET THAT TURNS MACHINE OFF WHEN REACHES A PRESET FOOTAGE. ANTI-REVERSE ROLL. SHEAR CUT SLITTING SECTION WAS UPDATED TO TIDLAND SERIES I. HAS (100) FEMALE BACK KNIVES, .5 WIDE AND (5) MALE SHEAR CUT KNIVES. WRAP SHEAR SLITTING. 1 MINIMUM SLIT WIDTH. BOWED ROLL. WINDING DRUMS, 55 WIDE. MAXIMUM REWIND DIAMETER, 15.75. HAS ADAPTORS FOR 3 ID REWIND. RELIANCE VARIABLE SPEED DC DRIVE, MINI PAK. SET UP ON 230 VOLT, 3 PHASE, 60 CYCLE. 7.5 HP BALDOR DC DRIVE MOTOR. RUBBER-COVERED RIDER ROLL; IT IS NO LONGER DRIVEN. INCLUDES TRIM BLOWER / CHOPPER. DYNAPAR COUNTER. MAXIMUM OPERATING SPEED, 1000 FEET PER MINUTE. TOP RIDER ROLL, 2.75 DIAMETER. CAN REWIND PAPER, LAMINATIONS, NON-EXTENSIBLE PRODUCTS & NONWOVENS.

WOLVERINE 46-4 HYDROLINE 2-COLOR ON 4-COLOR FRAME, STACK, HLRE, FLEXOGRAPHIC INLINE PRINTING PRESS. HAS SOME PARTS FOR 3RD AND 4TH PRINT STATION. 46 WEB WIDTH. 46 PRINT WIDTH. QUARTER PITCH GEARING. 10 TO 40 REPEAT RANGE. STAINLESS STEEL INK PANS & COVERS. MANUAL REGISTRATION CONTROL. SIDE REGISTER CONTROL ON ALL PRINT STATIONS. MANUAL 360 DEGREE REGISTRATION WHILE MACHINE IS RUNNING AT EACH PRINT STATION. VARIABLE SPEED OF INK ROLLERS. EACH COLOR STATION IS EQUIPPED WITH FREEWHEELING CLUTCH WHICH ALLOWS BOTH TRANSFER & INK ROLLERS TO ROTATE CONTINUOUSLY POWERED BY HYDRAULIC DRIVE DURING SHUTDOWN (I.E. CONSTANT ROTATION). 47 ANILOX ROLLS, 5 DIAMETER, CERAMIC . 46.5 CHROME-PLATED IMPRESSION ROLL, 8 DIAMETER. 47 RUBBER ROLLS, 5.5 DIAMETER. 8 DIAMETER IDLER ROLLS. (2) PRINT CYLINDERS, 44 WIDE, 5.2 DIAMETER. CONSTANT ROTATING INK ROLLS DURING STOP. PLATE CYLINDERS ARE AUTOMATICALLY LIFTED DURING STOP. HYDRAULIC TANK. 230/460 VOLTAGE, 3 PHASE, 60 CYCLE. PRINTING USING WATER-BASED INK. UP TO 700 FEET PER MINUTE. (2) STAINLESS STEEL INK PANS & COVERS. ONE IN-BETWEEN DRYER BOX. 30 DISTANCE BETWEEN EACH PRINT STATION. (2) HEAVY-DUTY AIR CLUTCHES WHICH ALLOWS DISENGAGEMENT OF PRINT STATIONS. CAN PRINT ON ONE STATION AND CHANGE OUT ROLLS ON THE OTHER STATION. GEARING IN GOOD CONDITION. NO MOTOR OR DRIVE. THIS PRINT STATION WAS PRINTING ON FILM. COULD BE PUT INLINE WITH EXTRUDER, POLY OR PAPER BAG MACHINE, SHEETER, SLITTER REWINDER, COATER, LAMINATOR, WAXER, ALMOST ANY PROCESS. MACHINE REFURBISHED.

W&H MATADOR MODEL 26 STRIKER BAR CUTOFF, MODEL CD, F&S, VARIABLE SIZE PAPER BAG MACHINE. BAG WIDTH, 2 TO 9.5. CUTOFF LENGTH, 4 TO 18.875. TYPICAL SPEED, 400 BAGS PER MINUTE, DEPENDENT UPON PAPER, GLUE, IF PRINTING, OPERATOR & ENVIRONMENT. UNWIND TO ACCOMMODATE 36 OD ROLL. ONE 3 UNWIND SHAFT. MANUAL SIDE SHIFTING. COLD GLUE FOR SEAM & BOTTOM GLUE POT. ONE 8.25 WIDE GUSSETED FORMER. THREE EXTRA FORMERS, 6.5", 7.5" & 8". DELIVERY DRUM, 9.5 FACE WIDTH. (4) GRIPPING STATIONS AROUND THE DRUM. MECHANICAL COUNTER. STANDARD TABLE VERTICAL DELIVERY. 10 PITCH GEARING. VARIABLE SPEED DRIVE. BOSTON GEAR DC MOTOR CONTROL, MODEL RATIOTROL. DRIVE SET UP ON 230 VOLTAGE. BALDOR DC 7.5 HP MOTOR. MAXIMUM WEB WIDTH, 28.5. SINGLE POSITION ATTACHED UNWIND. MANUAL SIDE SHIFTING. MANUAL ADJUSTMENT OF THE BRAKING. HAS MANUALLY ADJUSTED REGISTER ROLL TO REGISTER PRINT TO WEB. STRIKER BAR CUTOFF. 20 LONG DELIVERY TABLE. MACHINE IS IN GOOD MECHANICAL CONDITION. HAS BEEN RECENTLY OVERHAULED.

2016 ATLAS-COPCO GA30FF ROTARY SCREW AIR COMPRESSOR W/VERT. AIR TANK S/N: AP1330558, 3 PH., 40 HP, 5581 HOURS

WOLVERINE MODEL 31-6 HLRE HYDROLINE 6-COLOR STACK FLEXOGRAPHIC PRINTING PRESS. 31" WEB WIDTH. 31" WEB WIDTH. 30" PRINT WIDTH. PRESS WAS PRINTING PAPER INLINE WITH PAPER BAG MACHINE. 10 PITCH GEARING. CAPABLE OF PRINTING ON FILMS, PAPERS, LAMINATIONS & LIGHT BOARD. COULD BE PUT INLINE WITH BLOWN FILM EXTRUDERS, POLY OR PAPER BAG MACHINES, SHEETERS, SLITTER REWINDERS AND COATER / LAMINATORS. 10 TO 40 REPEAT RANGE. INK PANS, STAINLESS STEEL. PRESS FEATURES MANUAL REGISTRATION CONTROL AT EACH PRINT STATION. SIDE REGISTER CONTROL AT PRINT STATION. CAN SET REGISTER WHILE MACHINE IS RUNNING. INDEPENDENT SPEED CONTROL OF INK ROLLERS. VARIABLE SPEED HYDRAULIC DRIVE AT EACH PRINT STATION. WAS PRINTING WITH WATER-BASED INKS. EACH COLOR STATION EQUIPPED WITH FREEWHEELING CLUTCH WHICH ALLOWS BOTH TRANSFER AND INK ROLLERS TO ROTATE CONTINUOUSLY POWERED BY A HYDRAULIC DRIVE DURING THE SHUTDOWN. CONSTANT ROTATION OF ANILOX & RUBBER ROLL. (2) OF THE (6) PRINT STATIONS ARE EQUIPPED WITH HARRIS & BRUNO ENCLOSED DOCTOR BLADE ASSEMBLIES. TOTAL OF (6) PRINT CYLINDERS ARE INCLUDED. HAS AUTOMATIC PRINT CYLINDER LIFT DURING THE STOP. INCLUDES A HYDRAULIC TANK & RESERVOIR. MECHANICAL SPEED, 700 FEET PER MINUTE. (6) ANILOX ROLLS ARE INCLUDED. (6) RUBBER ROLLS ARE INCLUDED. (3) CHAMBERED DOCTOR BLADES. PRINT STATION 1 & 6 ARE SET UP WITH DOCTOR BLADE STATIONS. HAS GEARS WITH PRINT CYLINDERS. PRINT CYLINDERS ARE 31" WIDE. 6.4" DIAMETER OF PRINT CYLINDERS. 66-TEETH GEARS ON PRINT CYLINDERS. HAS CHANGE GEAR SYSTEM.

2015 ENERCON LM5809-18PVH-2DRB1B CORONAFLEX TREATER S/N: 122843-01. DESIGNED FOR HIGH-SPEED FLEXOGRAPHIC DIGITAL PRINTING APPLICATIONS. INTUITIVE TOUCH-SCREEN CONTROL. INCLUDES TREATER STATION, TRANSFORMER, POWER SUPPLY, REMOTE CONTROL EXHAUST SYSTEM, KEYPAD TOUCHSCREEN. COMPACT DESIGN. DESIGNED TO INCREASE THE SURFACE ENERGY OF PLASTIC FILMS, FOILS & PAPER.

APPLETON A300 AUTOMATIC CORE RECUTTER. OPERATOR LOADS CORE AND SETS THE TARGET TO THE DESIRED CORE LENGTH. THE OPERATOR THEN PRESSES A BUTTON ON THE PANEL TO ACTIVATE THE CUTTING CYCLE. THE A300 ADVANCES AND CUTS THE CORE UNTIL THE PARENT CORE IS CONSUMED. THE AIR POWERED KNIFE AND ELECTRIC CORE ADVANCE DRIVE MAKES SYSTEM EASY TO INSTALL AND MAINTAIN. KNIFE ON A300 IS FIXED AS OPPOSED TO A POWER SAW. KNIFE GENERATES NO DUST OR NOISE RESULTING IN AN ENHANCED BURNISHED CUT. 6 MANDREL. 460 VOLT, 3 PHASE, 60 CYCLE. TARGET ADJUSTS TO MAXIMUM 60 LENGTH CUTS. .25 HP MOTOR DRIVES PUSHER CORE ADVANCE. 2 HP MOTOR DRIVES, TURNS MANDREL. AIR-LOADED KNIFE CUT SYSTEM. WALL THICKNESS .25 - .625 THICK. MINIMUM CUT DETERMINED BY CORE INTEGRITY. TYPICALLY EQUAL TO WALL THICKNESS. HAS CONTROLS FOR CUTTING TIME AND FEED SPEED. TYPICAL CUT LENGTH TOLERANCE +/- .01. S/N: 0505588

2011 RETROFLEX K SERIES HD 2-COLOR STACK FLEXOGRAPHIC PRINTER. INLINE OPERATION. SERIAL # 20114528. WAS INLINE WITH A PAPER TUBER. PRINTING ON KRAFT PAPER. 54 MAXIMUM WEB WIDTH. MAXIMUM PRINT WIDTH, 52.5. MAXIMUM MECHANICAL DESIGN SPEED, 500 FEET PER MINUTE. SET UP 27 TO 43 REPEAT. FORMER OWNER WAS USING 27 AND 43 REPEAT. GEARING, 1/4 CIRCULAR PITCH, CP HELICAL. TENSION RANGE, 2 TO 3 PLI. WATER-BASED FLEXO INK. MECHANICAL REGISTRATION CAPABILITIES, +/- 1/64. SERVO MOTORS. TOTAL OF (2). EACH PRINT STATION HAS ONE 3 PHASE SERVO MOTOR, KOTTORGEN, 640 VOLT DC, 3500 RPM, 7.08KW. INCLUDES DANCER ASSEMBLY. THERE ARE (2) SERVO MOTORS, ONE PER PRINT STATION. CERAMIC ANILOX ROLLS. 57 CHROME-COVERED IMPRESSION ROLL. PNEUMATIC THROW OFF OF PRINT CYLINDER & IMPRESSION. HAS CONSTANT ROTATING INK. ELECTRIC MOTOR ON EACH ANILOX ROLL, 1/8 HP, 90 VOLTS. MANUAL SIDE REGISTRATION. AIR-LOADED RUBBER NIP ROLL ASSEMBLY. 2 THICK SIDE FRAMES. AIR-LOADED DANCER SYSTEM WITH 57 WIDE IDLERS. 5 DIAMETER ALUMINUM IDLERS. ANILOX TO PLATE ROLL NIP & PLATE TO IMPRESSION ROLL NIP ARE PNEUMATICALLY LOADED. SIDE-LAY ADJUSTMENT FOR SIDE-TO-SIDE REGISTRATION. SUNDAY DRIVE POTENTIOMETER CAN CONTROL SPEED FOR SUNDAY DRIVE. HAS AUTOMATIC PRINTER IMPRESSION ON / OFF. HAS ROLL NIP ON / OFF; ALLOWS TENSION BETWEEN THE DECK ONE AND THE DANCER TO BE ISOLATED. FACTORY WAS CLOSED AND PRINTER WAS MOVED TO WAREHOUSE. WHEN PRINTER WAS MOVED, OWNER MISPLACED TWO DOCTOR BLADE ASSEMBLIES, PRINT CYLINDERS & DRIVES. NO DOCTOR BLADES, NO PRINT CYLINDERS, NO DRIVES. PRINTER CAN PRINT ON PAPER, FILMS & LAMINATIONS. ORIGINAL SPECS ARE AVAILABLE. ORIGINAL MANUFACTURER CAN SELL NEW DRIVE SYSTEM, TWO NEW DOCTOR BLADE ASSEMBLIES & TWO NEW PRINTING PLATES.

20 HP POWERFLEX 755 DRIVES

KONPON KAKOHKI CO. LTD. 3-ROLL CALENDERING SYSTEM. 305X710. S/N: CR-60106210. ALL THREE ROLLS ARE HEATED. CALENDER HAS ELECTRIC MOTORS & LEAD-TYPE SCREWS. TWO MOTORS ON TWO OF THE ROLLS; TOTAL OF (4) MOTORS ON TWO ROLLS. CAN ADJUST LEFT & RIGHT SIDE OF THE ROLLS. INDICATOR ON EACH SIDE OF ROLLS GOES TO ZERO; THIS MEANS ROLLS WILL TOUCH. CAN SET THE GAP OPENING OF THE ROLLS VERY PRECISELY. SYSTEM IS DESIGNED TO CALENDER PRODUCTS TO EXACT THICKNESS. CONTROL THE GAP EASILY & VERY PRECISELY USING THE MOTORS. WAS USED WITH EPOXY ADHESIVE FOR TAPE PRODUCTS. CALENDER WAS USED FOR MAKING FLASHING TAPE FOR WINDOW SEAL, STANDARD FLASHING PRODUCTS, WINDOW SEAL TAPE & FLASHING TAPE. EPOXY COMPOUND ADHESIVE WAS DELIVERED TO THE TOP CALENDERING ROLL WHERE PRODUCT WAS METERED, CALENDERED, LINER WAS INTRODUCED, PRODUCT WAS THEN CHILLED AFTER HAVING BEEN CALENDERED TWO TIMES TO GET PROPER THICKNESS AND SPREAD. SECOND LINER WAS INTRODUCED AND LAMINATED TO PRODUCT AND THEN REWOUND. MACHINE IS MISSING THE CENTER REWIND STATION. INCLUDES (2) UNWINDS AND THE DRIVES FOR MOTORS. DRIVES ARE APPROXIMATELY 6 YEARS OLD. NITTO CORPORATION HAS EXITED THIS PRODUCT AND CONSEQUENTLY THE EQUIPMENT IS BEING SOLD. PARKER AC VARIABLE SPEED DRIVE, 690 SERIES WITH MITSUBISHI 18.5 KW DRIVE MOTOR, 230 VOLT, 3 PHASE, 60 CYCLE. PRIMARY UNWIND IS 2-POSITION UNWIND FOR LINER. MANUAL SIDE SHIFTING. ELECTRIC BRAKE. 36 DIAMETER ROLL OF LINER. HAS LE-M TENSION CONTROLLER FOR AUTO TENSION ON UNWIND. SECONDARY CANTILEVERED UNWIND IS ATTACHED TO CALENDER STAND. HAS ELECTRIC BRAKE. 3" AIR SHAFT. GUARDS INSTALLED. ALLOW 12" DIAMETER ROLL IF RE-DESIGN GUARD. 24" DIAMETER ROLL. SECONDARY UNWIND WAS USED FOR SOME PRODUCTS. 3-ROLL CALENDER; EACH ROLL IS IDENTICAL. 28 WIDE (710MM) WIDTH. 12 (305MM) DIAMETER. ALL THREE CALENDER ROLLS ARE HEATED; ROLLS COULD BE HEATED OR CHILLED. CENTER CALENDER ROLL IS STATIONARY. TOP & BOTTOM CALENDER ROLLS HAVE GAP ADJUSTMENT WITH ELECTRIC MOTORS TO SET GAP. HAS HANSEN PATENT GEARBOX WHICH DRIVES CENTER STATIONARY CALENDER ROLL. MACHINE HAS OIL CIRCULATION FOR BEARINGS ON THREE ROLLS. INCLUDES PUMP & RESERVOIR. AS YOU EXIT THE CALENDER, HAVE 24.5 WIDE, 8 DIAMETER, RUBBER-COVERED IDLER ROLL, WHICH IS CAN BE CHILLED.

LAWTON MODEL OBRX-RH ROLL FEED, SINGLE ROLL, HOUSEHOLD BATH TISSUE WRAPPER S/N: 1014. WRAPS INDIVIDUAL ROLLS OF HOUSEHOLD TISSUE ROLLS IN PAPER. THE STANDARD O SERIES WRAPPER IS CAPABLE OF MECHANICAL SPEEDS OF 80 WRAPS PER MINUTE. TYPICAL PRODUCTION SPEED, 60 TO 65 PER MINUTE. EQUIPPED WITH LAWTON ROLL FEED ATTACHMENT WITH SHEETER. UNWIND TAKES 18 DIAMETER ROLLS OF PAPER, 3 CORES. BELT-DRIVEN UNWIND, 4.5 WIDE BELT. STEEL-TO-RUBBER SEGMENTED PULL ROLL SECTION. 19 WIDE SHEETER KNIFE. DIETZ ELECTRIC EYE; CONTROLS THE CUTOFF OF SHEETER. CAN USE PRINTED WRAPPING PAPER; WILL SHEET ON MARK. (8) 4.5 CUPS. TYPICALLY CAN VARY THE DIAMETER OF ROLL .25" LOWER OR HIGHER. OB SERIES WRAPPERS HAVE ADJUSTMENTS TO HANDLE 4" TO 4.5" WIDE ROLLS. ELEVATOR & TOP PLUNGER. CRIMPER & SIDE PLUNGERS. EJECT ARMS. WITH CUPS THAT ARE PRESENTLY IN THE MACHINE, WILL HANDLE ROLLS FROM 4.25 TO 4.75 DIAMETER. IF DIFFERENT DIAMETER ROLLS ARE NEEDED TO BE WRAPPED, THEN THE PURCHASE OF DIFFERENT SIZE CUPS CAN BE MADE. TYPICAL OPERATING SPEED FOR LAWTON WRAPPER IS 60 TO 65 WRAPS PER MINUTE; THIS IS DEPENDENT UPON OPERATORS SKILL, ROLLS OF TISSUE, WRAPPER MATERIAL, ENVIRONMENT & CONDITION OF MACHINE. 2 HP AC MOTOR, 460 VOLTAGE. LINCOLN OILER. GOOD MECHANICAL CONDITION.

2000 GANNICOTT SHEETER / STACKER / INSERTER S/N: 8196. THIS SHEETER WAS SHEETING POSTED NOTES. HAS INSERTER WHICH WAS ADDING BACK SHEET. SERVOS AND DRIVES NEED TO BE UPDATED. HAS UNICO AC DRIVE, MODEL 2400 PERFORMANCE DRIVE, SET UP FOR 460 VOLT, 3 PHASE, 60 CYCLE. AC DRIVE MOTORS, 1.5 HP & TWO 7.5 HP. ALL IDLER ROLLS ARE COATED. 27 WIDE IDLER ROLLS. THIS SHEETER WAS MOVED & IS MOUNTED ON WHEELS. HAS PINWHEEL STACKER. HAS LAYBOY SECTION. INCLUDES VACUUM PUMP. SIEMENS S5 PLC, TOUCHSCREEN. HAS SPARE DRIVES, SPARE BLADES & SPARE PLC. 7.5 HP AC DRIVE ON CUTOFF KNIFE, 7.5 HP ON PULL ROLL & 1.5 HP ON CONVEYOR. 27.5 WIDE CUTOFF KNIFE. 8 DIAMETER CUTOFF KNIFE. TWO BLADES MOUNTED ON THE CUTOFF KNIFE. INCLUDES INSERTER. LAYBOY WILL ACCEPT 24 LONG SHEETS. LAYBOY IS SET UP FOR MAXIMUM SIZE OF 26X24. MACHINE IS IN GOOD MECHANICAL CONDITION.