Gibbs Brower International CorporationVacating BuildingWill Continue to Broker Equipment

HEAT GUN, DREMEL TOOL, PORTER CABLE SANDER, MILWAUKEE DRILL

(3) PALLETS OF WEBBER BAG FORMERS

CAMERON SHEAR KNIFE BLADE HOLDERS W/ (9) CUTTERS

CRAFTSMAN TOOL BOX W/WELDING RODS

4-DRAWER LATERAL FILES, TABLE WITH (6) ARM CHAIRS, (2) METAL SHELF UNITS, (2) WOOD/METAL SHELF UNITS

CRAFTSMAN TOOL BOX W/BLUE PORT. STAND

PEDESTAL ARBOR PRESS

B&D D.E. PEDESTAL BUFFER/GRINDER, 3 PHASE, 3/4 HP, 8"

SUPPLY CABINET W/CONTENTS INCLUDING HANDLES, KNOBS, CONTROLS, ETC.

DAYTON 150,000 BTU PORT. HEATER

ASST. GLUE POTS

DEWALT ELEC. GRINDER, MILWAUKEE ELEC. DRILL & (2) JIG SAWS

DAYTON 250 AMP AC/DC PORT. WELDER

ASST. CHAIN ON SHELF

G.E. 40 HP, 240 VOLT DC MOTOR

ASST. STEEL LEGGED TABLES

MAXSON SINGLE POSITION UNWIND. AUTOMATIC EDGE GUIDING. FIFE WEB GUIDE WITH PNEUMATIC SENSOR, +/- 4. 60 DIAMETER ROLL. WAS UNWINDING PAPER & BOARD. OPERATING AT 600 FEET PER MINUTE. WAS INLINE WITH SHEETER. NO UNWIND SHAFT.

PNEUMATIC SANDERS W/DISCS

MASTER 135,000 BTU PORT. HEATER

(2) ASST. TRANSFORMERS

GOEBEL MALE & FEMALE SHEAR CUT KNIVES WITH CART

1997 PEERLESS BF57.5 BLANK FED PLATE & TRAY FORMING LINE S/N: BF4-01-01. WAS MAKING FOOD SERVICE TRAYS. TAKES DIE CUT BLANKS, PUT IN LIFTING / FEEDING SECTION. FORMING HEAD SECTION. CONVEYOR / STACKER DELIVERY SECTION. BLANK FEED. MODEL BF57.5 GEAR DRIVEN VARIABLE SPEED 30-TON BLANK PRESS. 4 STROKE. PRESSING SERVICE, 57.5 WIDE BY 22 LONG. ANGLE OF MACHINE 35 DEGREES. MACHINE IS INTENDED TO BE USED FOR EITHER 1, 2, 3 OR 4 DIES OF VARYING SIZE AND CAN RUN UP TO 30 STROKES PER MINUTE. IN THE 2-WIDE CONFIGURATION, BLANKS OF 19.5 TO 24 WIDE. IN THE 3-WIDE SETUP, BLANKS CAN BE 7 TO 13.5. WITH 4 DIES, THE WIDTH CAN BE 7.5 TO 11.5. THE LENGTH OF THE BLANK SHOULD BE LESS OR EQUAL TO THE WIDTH WITH THE MAXIMUM LENGTH BEING 22. FORMING DIES ARE DESIGNED WITH THE MALE DIE MOUNTED ON THE BOTTOM. BLANK FEED SYSTEM DESIGNED FOR 1, 2, 3 OR 4 LANE SET UP. PAPER PLATE TRAY MACHINE OPERATION IS CONTROLLED FROM THE MAIN OPERATOR CONSOLE. MACHINE HAS SIEMENS READY PANEL. TEMPERATURE RANGE SETTINGS ARE DUE TO THE MANY TYPES OF PAPER COATINGS, MOISTURE CONTENT & INKS. TOP DIE, HEAT CAN BE CONTROLLED. BOTTOM DIE, HEAT CAN BE CONTROLLED & VARIED. MACHINE IS BASED ON CROWN BLANK FED FORMING. MAXIMUM FORMING DEPTH, TYPICALLY 1.5. (7) SETS OF STAINLESS STEEL DIES ARE INCLUDED; EACH SET MAKES A DIFFERENT PRODUCT. EACH SET IS MADE UP OF A TOP & BOTTOM DIE; TOTAL OF (14) PIECES. TOP & BOTTOM HEATING OF DIES. PHOTOS SHOW SAMPLES AND THE FORMING DIES FOR SIX OF THE PRODUCTS MADE ON THE MACHINE. # 4 FORMING DIE SET IS IN THE MACHINE. NO SAMPLE IS AVAILABLE. IT IS A 10"X14" OVAL PRODUCT AND IS SHOWN IN PHOTOS. MANUALS & BLUEPRINTS ARE INCLUDED. MACHINE IS IN EXCELLENT MECHANICAL CONDITION. APPROX. WEIGHT, 28,000 LBS. MACHINE FITS IN HIGH-CUBE CONTAINER. SET UP ON 480 VOLT, 60 CYCLE, 3 PHASE. AUTOCAD DRAWINGS OF DIES NEEDED TO MAKE DIES FOR BLANKS THAT ARE THEN USED IN PEERLESS MACHINE ARE AVAILABLE FROM PEERLESS.

WINDMOLLER & HOLSCHER ALINA X 3-COLOR, FLEXOGRAPHIC INLINE TAILEND PRINTING PRESS S/N: 7255. 32 WEB WIDTH. 31 PRINT WIDTH. 32.5 RUBBER ROLL. 32.5 ANILOX ROLLS. 32.5 IMPRESSION CYLINDERS. 9 TO 31.5 REPEAT RANGE. ALINA X30 FLEXOGRAPHIC TAILEND PRINTER. 30 DRYING DISTANCE BETWEEN EACH COLOR. 10 PITCH GEARING. DESIGNED WITH CENTRAL BULLGEAR WHICH HELPS TO ASSURE QUALITY PRINTING & GOOD REGISTER CONTROL. TYPICAL OPERATING SPEED, 600 FEET PER MINUTE. SPEED DEPENDS UPON MATERIAL & DRYING CAPABILITY OF THE INK USED & SUBSTRATE PRINTED. MOST RECENTLY PRINTING WITH WATER-BASED INKS. CYLINDER THROWOFF WHICH IS DONE MANUALLY. SOLID CONSTRUCTION & HEAVY-DUTY SIDE FRAMES ASSURE VIBRATIONLESS, HIGH-SPEED OPERATING & QUALITY PRINTING. SHAFT DRIVEN. MANUAL 360 DEGREE REGISTRATION CONTROLS. PRINTING PLATE CYLINDER IS MOVED FROM SIDE-TO-SIDE MANUALLY TO ADJUST FOR CROSS REGISTER. BOTH ADJUSTMENTS ARE MADE WHILE THE PRESS IS RUNNING. TWO 5.4 DIAMETER, THREE 5.2 DIAMETER, TWO 4.6 DIAMETER & TWO 6.2 DIAMETER PRINT CYLINDERS INCLUDED. 6 DIAMETER IMPRESSION CYLINDERS. 5 DIAMETER ANILOX ROLLS. 4.75 DIAMETER RUBBER ROLLS. MANUAL SIDE SHIFTING OF THE ENTIRE PRINTER LEFT & RIGHT 4. THIS PRINTER CAN BE USED WITH PAPER BAG MACHINES, POLY BAG MACHINES, LAMINATORS, SHEETERS, ETC. MOST RECENTLY WAS INLINE WITH PAPER BAG MACHINE. HAS CHANGE GEAR SYSTEM. REFURBISHED RECENTLY.

WEBER 3 FORMERS

ROCKPORT MACHINE & TOOL 6500 6" WIDE SINGLE COLOR FLEXOGRAPHIC PRINT STATION. 6 WIDE MAXIMUM WEB, S/N: 1799. SPEEDS UP TO 400 FEET PER MINUTE ADVERTISED. 5 DIAMETER PRINT CYLINDERS. ROLLS ARE DRIVEN BY THE WEB BEING PULL THROUGH. ROLLS HAVE SEALED PRECISION BALL BEARINGS. UNITS WERE ORIGINALLY BUILT FOR STAMPING / PRINTING ON THE INSIDE OR OUTSIDE OF TUBE/CORE STOCK. INLINE WITH WINDER. REVERSIBLE FOR PRINTING ON EITHER SIDE OF WEB. ROLLS ARE DESIGNED FOR EASY REMOVAL & CLEANING. ALSO INCLUDED IS A ROCKPORT MACHINE & TOOL MODEL 3500R 3" WIDE SINGLE COLOR FLEXOGRAPHIC PRINT STATION. 3 WIDE MAXIMUM WEB, S/N: 96.0403. SPEEDS UP TO 400 FEET PER MINUTE ADVERTISED. 5 DIAMETER PRINT CYLINDERS. ROLLS ARE DRIVEN BY THE WEB BEING PULL THROUGH. ROLLS HAVE SEALED PRECISION BALL BEARINGS. UNITS WERE ORIGINALLY BUILT FOR STAMPING / PRINTING ON THE INSIDE OR OUTSIDE OF TUBE/CORE STOCK. INLINE WITH WINDER. REVERSIBLE FOR PRINTING ON EITHER SIDE OF WEB. ROLLS ARE DESIGNED FOR EASY REMOVAL & CLEANING.

118 SINGLE SHAFT, CENTER REWIND, CUSTOM-BUILT SLITTER REWINDER. MOST RECENTLY USED AS A REREELER FOR COATED FILM. SCORE SLITTING. MALE AIR-LOADED SCORE CUT KNIVES WITH DOVETAIL BAR. HARDENED SCORE ROLL. (10) MALE KNIVES INCLUDED. ATTACHED UNWIND. 34 OD UNWIND ROLL. UNWIND SHAFT IS CARBON FIBRE AIR SHAFT FOR 3 CORES. AIR BRAKE. AUTOMATIC EDGE GUIDING. ACCUGUIDE ELECTRIC EYE SENSOR; MOVES UNWIND +/- 3". 22 MAXIMUM REWIND ROLL DIAMETER. ONE AIR CARBON FIBRE REWIND SHAFT FOR 3 CORES, 1500 LB. MAXIMUM WEIGHT CAPACITY. ONE PLASMA-COVERED PULL ROLL. ONE MOUNT HOPE BOWED ROLL LOCATED BEFORE SLITTING SECTION. RED LION COUNTER WITH AUTO STOP. MAG POWER MODEL TC-5 AUTOMATIC TENSION CONTROL. AC DRIVE. 3 HP WEG MOTOR. 230 VOLT, 3 PHASE, 60 CYCLE. PREVIOUSLY USED FOR SLITTING POLY COATED PAPERS, FILMS COATED FABRICS. TYPICAL OPERATING SPEED 100 FEET PER MINUTE. MAXIMUM MECHANICAL SPEED, 200 FEET PER MINUTE. CAN BE USED FOR SLITTING PAPER, FABRIC, NONWOVENS, LAMINATIONS & FILMS.

PERINI MODEL 606, SERIES 110 2-LANE LOGSAW WITH CIRCULAR BLADE FOR TOILET ROLL AND / OR KITCHEN ROLLS. WAS CUTTING TOWEL ROLLS MOST RECENTLY. SET UP ON 7.85 CUT LENGTH. WITH EXISTING CLAMPS IN MACHINE, ROLL DIAMETER 110/120MM OR 4.4 4.8 DIAMETER. BY CHANGING THE CLAMPS, OTHER DIAMETERS COULD BE CUT ON THIS SAW. CAN PUT INSERTS IN CLAMPS TO CUT SMALLER DIAMETER ROLLS. CUTOFF IS CHANGED WITH TWO SPROCKETS. 2-LANE PUSHER-TYPE INFEED. 13-FOOT INFEED CONVEYOR & TRAYS. (4) PUSHERS FOR EACH LANE. PUSHERS ARE MOUNTED 116 APART. INFEED SECTION HAS CHAIN TENSIONER THAT ALLOWS THE IDLER SPROCKETS TO BE MOVED BACK TO ACCOMMODATE LONGER LOGS IF NECESSARY OR TO ADD AN ADDITIONAL PUSHER FOR SHORTER LOGS. CUTOFF & LOG LENGTH COULD BE ADJUSTED TO MEET CUSTOMERS REQUIREMENTS AT AN ADDITIONAL COST TO THE QUOTATION. BLADE GRINDING SYSTEM. TWO GRINDING MOTORS. ONE INDEXER PUSHER MOTOR. ONE BLADE MOTOR. ONE MOTOR FOR OUTFEED DISCHARGE CONVEYOR SYSTEM. MODERN UPDATED VARIABLE SPEED DRIVE ON BLADE. ABB AC INVERTER DRIVE. 10 HP AC MOTOR ON BLADE. 440 VOLTAGE, 60 CYCLE, 3 PHASE. 6-FOOT LONG OUTFEED DELIVERY CONVEYOR. 24 DIAMETER BLADE. INFEED. 30 LONG BELT-DRIVEN HOLD-DOWN SYSTEM TO ASSIST WITH CUTOFF. INCLUDES MOTORS TO ADJUST THE BLADE DEPTH OF CUT AS BLADE WEARS DOWN; CAN EASILY ADJUST THE DEPTH OF THE BLADE CUT. MAXIMUM MECHANICAL SPEED OF CUTOFF, 100 CUTS PER MINUTE ON TISSUE. CUTOFF FOR TOWELING IS TYPICALLY 50 CUTS PER MINUTE. SPEED DEPENDENT UPON PRODUCT BEING CUT, LENGTH OF LOG AND DIAMETER OF LOG. LOGSAW WAS MOST RECENTLY INLINE WITH PCMC 150 SERIES AUTOMATIC REWINDER OPERATING AT 1200 FEET PER MINUTE. NEW CHAINS. IN GOOD CONDITION.

1999 MAP SYSTEMS THERMO LAM 3 LAMINATOR. 2-PLY THERMAL LAMINATION SYSTEM. 300 FEET PER MINUTE. WAS LAMINATING FILMS THROUGH HEAT & PRESSURE. INCLUDES (2) PILLAR TREATERS FOR TREATING THE TWO WEBS BEFORE THE WEBS ARE LAMINATED. AC VARIABLE SPEED DRIVES. 230 VOLT, 3 PHASE, 50/60 CYCLE. HITACHI CONTROLLERS. G.E. AC MOTORS, 5 HP MOTORS. 40 DIAMETER ON PRIMARY SINGLE POSITION UNWIND. 24 DIAMETER ROLLS ON SECONDARY UNWIND. 6 CORES ON PRIMARY & SECONDARY UNWINDS. PRIMARY CENTER REWINDER. 40 DIAMETER, 3 AIR SHAFTS. HAS SECONDARY LINER REWINDER. SINGLE POSITION PRIMARY UNWIND WITH WITCHITA MISTROL AIR BRAKE. ACCUWEB MICRO 1000 AUTO EDGE GUIDE SYSTEM. (2) 42 CORONA TREATERS, PILLAR TECHNOLOGIES MODEL P6015. .5 KW PILLAR TREATERS. 240 VOLT, 50 / 60 CYCLE. NEXT INLINE IS 45 WIDE LAMINATING STATION, HEATED AMERICAN ROLL WITH AIR-LOADED HEATED NIP ROLL. AFTER THE HEATED NIP LAMINATION STATION IS AN AIR-LOADED HEAT ROLL; SAME SIZE AS FIRST AMERICAN ROLL. TWO HEAT ROLLS ARE AMERICAN ROLLS THERMO LAM RI200 ELECTRICALLY HEATED ROLLS. MANUFACTURERS BROCHURE INDICATES MODEL R1200 IS CAPABLE OF TEMPERATURES UP TO 600 DEGREES FAHRENHEIT. AFTER LAMINATING STATION AND THE SECOND AMERICAN ROLL, THERE IS A CHILL ROLL, APPROXIMATELY 9 DIAMETER. WATER-COOLED, AIR-LOADED DANCER CONTROL SYSTEM ON REWINDER. ACCUWEB MICRO 1000 AUTO EDGE GUIDE ON REWIND. PARKER AUTO MOTOR CTC TOUCHSCREEN. ALLEN BRADLEY SLICK 800 PLC. INCLUDES A SECONDARY CENTER REWIND LINER REWINDER. MAP SYSTEMS MODEL LCP-10, SERIAL # 701022, AGE 1999. MAP SYSTEMS MODEL LAM-42, SERIAL # 651004, AGE 1999.

POTDEVIN 100 SERIES FORMERS

GORDEN CHADWICK PATCH UNIT

CUSTOM-BUILT ROTARY DIE CUTTING SECTION. WAS INLINE WITH POTDEVIN 84 PAPER BAG MACHINE. DIE CUTTING 2-PLY POTATO BAGS, WINDOW. SHEETING MESH AND APPLYING TO MOVING WEB. 10 PITCH GEARING. TWO REGISTRATION ROLLS. WILL ACCEPT 29.5 WIDE MATERIAL. SIDE SHIFT DIE CUTTING SECTION +/- 2. SHAFT DRIVEN. WAS CUTTING OUT 2.5 X 7.5 OPENING FOR POTATO BAGS. INCLUDED IS 8 SHEETER. CHANGE CUTOFF OF SHEETER BY CHANGING A GEAR. CHAIN DRIVEN. SINGLE POSITION UNWIND FOR MESH. 36 DIAMETER ROLLS OF MATERIAL. 3 CORE. UNWIND MESH, THEN SHEET. THIS SHEETING SECTION WAS INLINE WITH POTDEVIN BAG MACHINE SHEETING MESH, THEN APPLYING MESH TO DIE CUT WINDOW. CAN CHANGE THE FEMALE DIE.

HUDSON SHARP DESIGNED PAPER-TO-STEEL EMBOSSING SECTION. EMBOSSING PATTERN NEEDS TO BE RE-ENGRAVED ONTO STEEL ROLL. MOST RECENTLY BEEN USED AS A PULL ROLL SECTION AND AS A PERFORATING SYSTEM. WAS INLINE WITH HUDSON SHARP / FMC WIPES FOLDER. WAS ALSO PERFORATING NONWOVENS WIPES. OPERATING AT APPROXIMATELY 500 FEET PER MINUTE. STEEL ROLL, 15.25 EMBOSS PATTERN, 4 DIAMETER. PAPER ROLL, 15.25 EMBOSS PATTERN, 8 DIAMETER. 2:1 RATIO. ROLLS ARE GEARED TOGETHER. BOTTOM ROLL, WHICH IS THE PAPER ROLL, IS DRIVEN; HAS LINESHAFT. MECHANICAL LOADING OF ROLLS. 15 WIDE IDLERS, 4 DIAMETER, ALUMINUM. (3) IDLER ROLLS. MOUNTED ON EMBOSSER PULL ROLL SECTION IS A 17 WIDE PERFORATOR. (2) AIR CYLINDERS TO ENGAGE PERFORATOR ROLL. HAS HARDENED ROLL & ROTATING PERFORATOR ROLL. ELECTRIC CLUTCH WHICH ENGAGES THE PERFORATOR SYSTEM. PERFORATOR ROLL HAS ONE BLADE. 12.5 PERFORATION DISTANCE. MECHANICAL SYSTEM. HAS ON / OFF SWITCH. WHEN TURNED ON, ENGAGE PERFORATOR ROLL TO TURN. ALSO ENGAGE (2) AIR CYLINDERS TO LOWER PERFORATOR ROLL TO PERFORATE THE WEB.

2012 ENERCON LM5238 TREATER STATION S/N: 102199. ONE SINGLE POSITION UNWIND, CANTILEVERED, 20 DIAMETER ROLLS, 3 CORES. AIR BRAKE. MANUAL EDGE GUIDING. TREATER HAS TWO HEADS. RATING 1 KW, MODEL LM5269-RO-35. TWO TREATER BARS / TWO TREATER HEADS, RATING 1 KW, MODEL LM5269-RO-3. SERIAL # 102199-01. 240 VOLT INPUT, 6.5 AMPS, 50/60 CYCLE, 1 PHASE. ONE TRANSFORMER, 7 KVA, MODEL TF3002. ONE TREATER STATION, MODEL SS2671, SERIAL # 8357-3. ONE REMOTE CONTROL, MODEL LM5238-04, SERIAL # 102199-03. ENERCON TREATER MOUNTED ON STAND WITH WHEELS. TREATER WAS MOVED TO DIFFERENT LINES. MACHINE IS IN EXCELLENT CONDITION. WAS TREATING FILMS.

32 SHEAR CUT SECTION WITH GROOVED RAZOR ROLL. SHEAR CUT SECTION WAS REMOVED FROM 30" WIDE ARROW SLITTER REWINDER. INCLUDES (5), 35 FACE WIDTH, 38.5 WIDE MALE SHAFTS. ID OF MALE & FEMALE SHEAR KNIVES IS 60MM. OD OF MALE SHEAR CUT KNIFE IS 103-105MM. OD OF FEMALE SHEAR KNIFE IS 85MM. INCLUDES (24) MALE SHEAR CUT KNIFE HOLDERS WITH BLADES. SET UP FOR MINIMUM SLIT WIDTH OF 1. (6) FEMALE DRIVEN SHEAR CUT KNIFE SHAFTS, 39.25 WIDE, 43.75 OVERALL WIDTH. FEMALE SHAFTS ARE DRIVEN. (50) FEMALE SHEAR CUT KNIVES & HOLDERS. HAVE COUPLINGS TO HOLD THE MALE / FEMALE SHAFTS. UP TO 1,000 FEET PER MINUTE.

W&H QMS945 32" RUBBER & ANNILOX ROLLS, W&H QMS945 31" FACE WIDTH

32" ROLLS FOR QMS 922

WEBER 5 FORMERS

2000 MEECH 903 STATIC ELIMINATOR, 58" WIDE. POWER SUPPLY, 110 VOLTAGE, 50/60 CYCLE. RICHMOND PULSE FLOW CONTROLLER, STATIC ELIMINATOR; SET UP ON 120 VOLTAGE. (3) BARS & (4) NOZZLES. THESE STATIC ELIMINATORS WERE INLINE WITH A SHEETER THAT HAD BEEN SHEETING FILM PRODUCTS.

330 GALLON OIL STORAGE TANK, 12 GAGE

1970 WINDMOLLER & HOLSCHER MODEL 8130, ALINA 800 SINGLE COLOR INLINE FLEXOGRAPHIC PRINTING PRESS. 1 COLOR. S/N: 21220. MODEL 8130. THIS PRINTER WAS INLINE WITH A PAPER BAG MACHINE. MECHANICAL SPEEDS 1200 FPM. TYPICAL OPERATING SPEED 1000 FPM. SINGLE COLOR PRINTER. HAS SECOND COLOR STATION WHICH IS 80 PERCENT COMPLETE. MANUAL REGISTRATION CONTROL BOTH WAYS. AIR PICK UP OF PLATE CYLINDERS. 44 RUBBER ROLL, 6 DIAMETER. 44 CHROME ANILOX ROLL, 6 DIAMETER. 42 WIDE PRINT CYLINDER, 5.5 DIAMETER. 47 WIDE IMPRESSION ROLL, 6 DIAMETER, STEEL. CHANGE GEAR SYSTEM. MANUAL EDGE GUIDING FOR EDGE GUIDING PRINTER ON STAND +/- 2. LINESHAFT DRIVEN. 10 PITCH. THIS MACHINE COULD BE PUT INLINE WITH PAPER BAG MACHINE OR MANY OTHER PROCESSES. THIS IS AN ALINA PRINTER FOR USE IN COMBINATION WITH CONVERTING MACHINES, EXTRUDERS, PAPER BAG MACHINES, SHEETERS, COATERS & LAMINATORS. PRINT REPEAT 30 TO 90CM (11.8 - 35.4). HEAVY-DUTY, HIGH SPEED. PULL ROLL SECTION. MANUAL REGISTRATION CONTROL.

PCMC 102 PLY-BONDING UNIT S/N: 7293. PLY-BONDING SCORING ROLL, PCMC SCORE CUT SLITTING SECTION - 102 PCMC PLY-BONDING UNIT. SERIAL # 7293. PLY-BONDING SCORING ROLL, PCMC SCORE CUT SLITTING SECTION, 103 WIDE, 12 DIAMETER, STEEL. INCLUDES (22) AIR-LOADED PLY BONDERS. EACH PLY BONDER IS 3.5 WIDE. 1 WIDE PLYING WHEELS. EACH PLY BONDER HAS ITS OWN REGULATOR. 103 WIDE, 5 DIAMETER MOUNT HOPE BOWED ROLL THAT IS DRIVEN. REXROTH, 18.4 KW, AC VARIABLE SPEED DRIVE MOTOR, SET UP FOR 600 VOLT. HAS CARBON FIBER TENSION ROLL WITH ABB TRANSDUCERS AND ABB PFEA11 CONTROLLER FOR AUTOMATIC TENSION CONTROL SYSTEM. EMERGENCY BRAKE SYSTEM ON PLY-BONDING SCORING ROLL. 2 THICK FRAMES. WAS INLINE WITH PCMC HIGH-SPEED REWINDER. OPERATING AT 1800 FEET PER MINUTE.

BLACK CLAWSON M-2110 3-ROLL REVERSE ROLL COATING STATION. ALL ROLLS IN MACHINE ARE 66" WIDE. TWO 66" WIDE CHROME ROLLS, 11" DIA. ONE 66" WIDE RUBBER-COVERED ROLL, 11" DIA. TOP CHROME METERING ROLL IS AIR-LOADED DOWN TO MIDDLE CHROME APPLICATOR ROLL. TOP CHROME METERING ROLL HAS WEDGE BLOCK MICROMETER ADJUSTMENT TO ADJUST THE GAP BETWEEN THE TOP METERING ROLL AND THE APPLICATOR ROLL. BOTTOM RUBBER-COVERED BACKUP ROLL IS AIR LOADED UP TO THE APPLICATOR ROLL AND HAS WEDGE BLOCK MICROMETER ADJUSTMENTS. METERING ROLL HAS 66" WIDE DOCTOR BLADE ASSEMBLY WHICH IS AIR-ACTIVATED. MIDDLE ROLL, APPLICATOR ROLL IS STATIONARY. MACHINE INCLUDES ONE DRIP PAN. MACHINE INCLUDES (4) EXTRA DOCTOR BLADES. 3-ROLL REVERSE ROLL COATER IS DESIGNED FOR NIP FEED EMPLOYING ANTI-FRICTION BEARINGS. PRECISION GROUND ROLLS, PRECISION GREASE LUBRICATED BEARINGS, HEAVY CAST IRON FRAMES, ACCURATE MICROMETER STOPS (INDICATING HAND WHEEL OPTIONAL) & PNEUMATIC ROLL ACTUATION. HAS EDGE MARGIN CONTROL. ALL ROLLS ARE INDEPENDENTLY REMOVABLE. SPEEDS UP TO 800 FPM. HAS DOUBLE BEARING SEAL ARRANGEMENT. THIS COATING STATION WAS USED FOR TAPE COATING ON FILMS. TYPICAL APPLICATIONS ARE ORGANISALS, PLASTISOLS, LACQUERS, ELECTROPHOTOGRAPHICS, HEAVY EMULSIONS, DISPERSIONS, RELEASE COATINGS, FILM CASTING, RUBBER-BASED ADHESIVES ON ALL MATERIALS.

1998 JONES CARTONER SET UP FOR FORMAT OF REGULAR, BIG & CUBE FACIAL BOXES. AB/SLC504 ELECTRONIC PLATFORM. CAN MAKE FLAT BOXES OR POP-UP CARTONS. HAS NORDSON VISTA SERIES S3500 HOT-MELT GLUE APPLICATOR. THIS CARTONER WAS INLINE WITH 7-LANE BRETTING FACIAL INTERFOLDER. INCLUDES CHANGE PARTS & SPARE PARTS. HAS CHANGE PARTS TO RUN THREE DIFFERENT SIZE CARTONS. JONES CARTONER IS EASY TO PROGRAM TO INTEGRATE WITH OTHER FOLDERS. INCLUDES COMPUTER & DRIVES FOR SERVO. MANY MANUALS INCLUDED. WHEN CHANGING FROM ONE SIZE CARTON TO ANOTHER, EASY TO CHANGE. ALLEN BRADLEY SLC 504 PLC. EASY TO RE-PROGRAM. SERVO PROGRAM IS SIMPLE. SERVO MOVEMENT IS A SIMPLE TRAPEZIAL MOTION, ACCELERATE, VELOCITY, DECELERATE & JOG. FORMER OWNER INDICATES THE FASTEST THEY RAN THE CARTONER WAS 54 CARTONS PER MINUTE. THE LIMITING FACTOR WAS THE FOLDER. S/N: S-5548

MAXON 2-POSITION UNWIND STAND. 60" DIAMETER ROLLS. WAS INLINE WITH MAXON SHEETER OPERATING AT APPROXIMATELY 600 FEET PER MINUTE. TWO POSITIONS. NO UNWIND SHAFTS. EACH POSITION HAS MANUAL SIDE SHIFTING +/- 2. TWO STEEL IDLERS, 46.5" WIDE, 3.5" DIAMETER.

1980 FAUSTEL 2-DRUM SURFACE REWIND SINGLE SHAFT REWINDER. WAS INLINE WITH A LAMINATOR OPERATING AT APPROX. 750 FPM. WAS REWINDING FILM PAPER LAMINATIONS. SMOOTH STEEL BEDROLLS. FACE WIDTH OF BEDROLLS 56". BEDROLLS ARE GEARED TOGETHER & ARE TIMING-BELT DRIVEN. 10" DIA. BEDROLLS. HAS UPPER RIDER ROLL; UPPER RIDER ROLL IS NOT DRIVEN. 68" WIDE STEEL UPPER RIDER ROLL, 6" DIA. TOL-O-MATIC CYLINDERS; ONE ON EACH SIDE FOR AIR ASSIST. AIR CYLINDERS LIFT OR PRESS DOWN UPPER RIDER ROLL. AIR CYLINDERS CONTROL AMOUNT OF DOWNWARD PRESSURE OF UPPER RIDER ROLL WHICH ASSURES TIGHTLY WOUND ROLLS. NO REWIND SHAFTS INCLUDED. 61.5" WIDE, 4" DIA. MOUNT HOPE BOWED ROLL SYSTEM. MECHANICAL SPEEDS UP TO 1000 FPM. MAXIMUM REWIND WEIGHT 5000 LBS. MAXIMUM REWIND 60" DIA. 10 HP BALDOR DC DRIVE, 240 VOLT. NO CONTROLLER INCLUDED WITH DRIVE MOTOR. REWINDER COULD BE USED FOR PAPER, LAMINATIONS & BOARD. WAS OPERATED WITH 3" REWIND SHAFTS. (2) 58" WIDE, 4" DIA. ALUMINUM IDLERS. COULD BE USED INLINE WITH COATER, LAMINATOR, PRINTER & WAXER. BECAUSE OF SMOOTH BEDROLLS, SENSITIVE MATERIALS CAN BE REWOUND.

2003 CHESNUT MODEL 150 LAMINATOR / PRINTER, 2-ROLL ROTOGRAVURE COATING STATION, S/N: 286. WEB WIDTH 15 (380MM). SPEEDS UP TO 600 FPM. MATERIAL RANGE: PAPER & PAPER BOARD UP TO .015, FILMS, FOILS. 2-ROLL GRAVURE COATING OR REGISTER PRINT STATION WITH 13 FT. GAS DRYER LAMINATING STATION AND SECONDARY SINGLE POSITION UNWIND. SECONDARY SINGLE POSITION UNWIND SET UP FOR 3 CORES. 30 DIAMETER ROLLS. UNWIND HAS COAST PNEUMATIC AUTOMATIC EDGE GUIDING SYSTEM. EDGE GUIDE THE SECONDARY UNWIND. AIR BRAKE & AUTOMATIC TENSION CONTROL SYSTEM ON SECONDARY UNWIND. 480 VOLTAGE, 60 CYCLE, 3 PHASE. EXPLOSION-PROOF. GAS BURNER & BLOWER. 13 FT. LONG DRYER, EXPLOSION PROOF. SOLVENT & WATER-BASED COATINGS / INKS. IDLERS IN MACHINE ARE 16 WIDE. ENCLOSED DOCTOR BLADE ASSEMBLY. 10 TO 20 REPEAT RANGE. GAS BURNER & BLOWER ARE INCLUDED. GAS BURNER & BLOWER WERE LOCATED ON THE ROOF OUTSIDE. CAN REVERSE PRINT / COAT BY VARYING THE WEB PATH. ELECTRICS & DRIVES INCLUDED. IN 2005, NEW AC SERVO DRIVE & CONTROL SYSTEM ADDED. RATIOMATIC BURNER, 50 RM. 500,000 BTU BURNER. HAS SUPPLY, EXHAUST, COMBUSTION MOTORS. BURNER IS CHESNUT ENGINEERING MODEL 150, SERIAL # 2.86-5. HAS CINCINNATI FAN BLOWER, RBE-11, SERIAL # 303281 AND CINCINNATI FAN MODEL HDBI-150, SERIAL # 303280.

1980 FLEXOLINE FLEXOGRAPHIC SINGLE COLOR PRINT STATION. MAXIMUM WEB WIDTH 52". MAXIMUM PRINT WIDTH 50". WIDTH OF ALL ROLLS 52". 52" WIDE, 6.5" DIA. RUBBER & CERAMIC COATED ANILOX ROLL. 52" WIDE, 7" DIA. IMPRESSION CYLINDER CHROME-PLATED. BOWED ROLL BEFORE PRINT STATION. AC MOTOR FOR CONSTANT ROTATING INK FEATURE. 1/2 HP MOTOR. AUTOMATIC PLATE CYLINDER PICKUP. WHEN PRESS IS STOPPED, PRINT CYLINDER AUTOMATICALLY PICKS UP & BEGINS ROTATION. 10 HP VICTOR AC MOTOR 480 VOLT, 3 PHASE, 50/60 CYCLE. THIS MOTOR DRIVES THE PRINT STATION. CONTROL TECHNIQUES UNIDRIVE CONTROLLER FOR THE DRIVE MOTOR. AFTER PRINT STATION HAS 32" LONG DRYER BOX. MACHINE DOES NOT INCLUDE A PRINT CYLINDER. PRINTING STATION HAD BEEN INLINE WITH A CI PRINTING PRESS PRINTING ON PAPERS. REPEAT RANGE 18-48". AT ONE POINT IN TIME, HAD GAS BURNER & BLOWER; THOSE ARE NOT INCLUDED. FLEXO PRINTING STATION AT THE TIME WAS USED FOR COATING & PRINTING ON FILM LAMINATIONS & PAPER FOR MULTIWALL SACK BAGS. PLATE THICKNESS .112. STICKY BACK THICKNESS .02". 1/4 PITCH. MECHANICAL SPEED 1000 FPM.

1990 SHAR CENTER REWIND REREELER AND INSPECTION MACHINE. THIS MACHINE WAS UNWINDING & REWINDING ROLLS OF METALIZED FILMS. UNWIND WILL ACCEPT 34 DIAMETER ROLLS. REWIND WILL REWIND 40 DIAMETER ROLLS. 1500 FEET PER MINUTE. VARIABLE SPEED. CLEVELAND CONTROLS. DC DRIVE, 230 VOLT, 3 PHASE, 60 CYCLE. 20 HP BALDOR DC DRIVE MOTOR. DURANT COUNTER WITH PRESET. 67 WIDE IDLERS, 5 DIAMETER. IF BYPASS INSPECTION SYSTEM, 65 WIDE PRODUCT CAN BE REWOUND. DETACHED UNWIND. 3 AIR SHAFT WITH 6 & 12 CHUCKS. 8 MONTALVO AIR BRAKE. FIFE PNEUMATIC SENSOR. AUTOMATIC EDGE GUIDING; MOVES UNWIND LEFT / RIGHT, +/- 3. FIRST IDLER MOVES WITH UNWIND. AFTER UNWIND, GOES INTO INSPECTION SYSTEM, LIGHT SYSTEM. 3 DIAMETER BOWED ROLL BEFORE INSPECTION LIGHT. 5 DIAMETER RUBBER SPREADER ROLL AFTER INSPECTION SYSTEM, BEFORE REWIND. CENTER REWIND. 5 DIAMETER, 67 WIDE RUBBER-COVERED LAYON ROLL, WHICH IS AIR-LOADED DOWN AGAINST THE REWINDING ROLL. CAN CONTROL THE AMOUNT OF PRESSURE DOWN ON REWINDING ROLL TO HELP WITH TIGHTLY REWOUND ROLLS. 3 AIR REWIND SHAFT.

1997 VALLEY TISSUE PACKAGING 1500 AUTOMATIC DIVERTER WITH 2-LANE CHOKE INFEED SYSTEM. S/N: C253-1500-2-4-97. DIVERTER 2-4 BRT. 2:4 DIVERTER WITH A 9 FOOT LONG X 42 WIDE CONVEYOR SYSTEM. SHUTTLE THE PRODUCT WITH SIMPLE SMOOTH MOTION. HIGH SPEED. WAS INLINE WITH 104, 2000 FEET PER MINUTE TISSUE REWINDER. CAN ACCEPT 2 LANE AND DIVERT TO 4 LANES. POWERED BY 2 HP SIEMENS AC MOTOR. ALLEN BRADLEY SLK-5 PLC. 2-LANE CHOKE WITH ADJUSTABLE HEIGHT, 5 FEET LONG. EACH LANE HAS ITS OWN 1 HP AC MOTOR. CONTROLLER IS ALLEN BRADLEY. VARIABLE SPEED AC INVERTER DRIVES. (2) ALLEN BRADLEY POWERFLEX 4 DRIVE CONTROLLERS. 460 VOLT, 3 PHASE, 60 CYCLE. SIEMENS AC MOTORS. ONE 2 HP MAIN DRIVE MOTOR AND TWO 1 HP MOTORS. IN VERY GOOD MECHANICAL CONDITION. ELECTRICAL DRAWINGS INCLUDED. THIS DIVERTER WAS INLINE WITH HIGH-SPEED WRAPPER. NO OPERATOR REQUIRED. ROTARY MOTION. PRODUCT, UNWRAPPED TISSUE ROLLS OR WRAPPED PAPER OR POLY PACKAGES OF TISSUE ROLLS OR OTHER PRODUCTS. PRODUCT DIMENSIONS: TISSUE ROLLS, 3.5 TO 6 DIAMETER, 4 TO 11 CUTOFF. PLC HAS PROGRAM INSTALLED AND WORKING.

1991 DUSENBERY 794 DH ROLL DOCTORING MACHINE. HEAVY-DUTY DESIGN FOR LARGER DIAMETER ROLLS. CANTILEVERED UNWIND / REWIND. EL ELECTRIC EYE. 2-ROLL AUTOMATIC EDGE GUIDING, +/- 2. AIR-LOADED DIFFERENTIAL REWIND FOR LIGHTWEIGHT EXTENSIBLE FILM MATERIALS. REWIND SHAFT ALSO HAS AN AIR CLUTCH FOR LOCKED CORE REWINDING. SINGLE POSITION UNWIND, 4 AIR BRAKE, 3 CORE, 24 DIAMETER ROLLS. CENTER REWINDER DESIGNED FOR 22 DIAMETER REWIND WHEN USING RIDER ROLL AND 24 DIAMETER REWIND WITHOUT RIDER ROLL. HAS LAYON ROLL ASSEMBLY. CENTER REWINDER. AIR-LOADED DIFFERENTIAL ON REWIND. KB ELECTRONICS. VARIABLE SPEED DC DRIVE, 240 VOLT, 1.5 HP BALDOR MOTOR. 5 WIDE IDLERS. CORK-COVERED IDLERS. THIS MACHINE WAS UNWINDING & REWINDING NARROW ROLLS OF FILM PRODUCTS WHICH HAVE VERY LOW TENSION. TYPICAL OPERATING SPEED, 1,000 FEET PER MINUTE. S/N: 22239