Gibbs Brower International CorporationVacating BuildingWill Continue to Broker Equipment

GOEBEL WETTING / COATING / MOISTURIZING STATION. THIS STATION WAS COATING THE WEB WITH WATER TO REMOISTURIZE THE WEB. OPERATING SPEED, 1000 FEET PER MINUTE. HAS SIEMENS AC DRIVE MOTOR, WHICH DRIVES THE COATING ROLL WHEN COATING. SET UP FOR 380 VOLT, 3 PHASE, 50 CYCLE. TWO IDLER ROLLS, 67 WIDE. 4 DIAMETER IDLERS. WETTING ROLL IS DRIVEN BY A SMALL AC MOTOR. 67 WETTING ROLL IS AIR-LOADED UP IN TO THE WEB; COATS THE BOTTOM OF THE WEB. TWO IDLER ROLLS; CONTROL THE WEB PATH. COATING ROLL IS AIR-LOADED UP INTO THE WEB. STAINLESS STEEL PAN. VERY COMPACT COATING STATION. COULD BE PUT INLINE WITH COATERS, LAMINATORS, SLITTER REWINDERS & MANY OTHER PROCESSES.

LAWTON MODEL OBRX-RH ROLL FEED, SINGLE ROLL, HOUSEHOLD BATH TISSUE WRAPPER S/N: 914. WRAPS INDIVIDUAL ROLLS OF HOUSEHOLD TISSUE ROLLS IN PAPER. THE STANDARD O SERIES WRAPPER IS CAPABLE OF MECHANICAL SPEEDS OF 80 WRAPS PER MINUTE. TYPICAL PRODUCTION SPEED, 60 TO 65 PER MINUTE. EQUIPPED WITH LAWTON ROLL FEED ATTACHMENT WITH SHEETER. UNWIND TAKES 18 DIAMETER ROLLS OF PAPER, 3 CORES. BELT-DRIVEN UNWIND, 4.5 WIDE BELT. STEEL-TO-RUBBER SEGMENTED PULL ROLL SECTION. 19 WIDE SHEETER KNIFE. DIETZ ELECTRIC EYE; CONTROLS THE CUTOFF OF SHEETER. CAN USE PRINTED WRAPPING PAPER; WILL SHEET ON MARK. (8) 4.5 CUPS. TYPICALLY CAN VARY THE DIAMETER OF ROLL .25" LOWER OR HIGHER. OB SERIES WRAPPERS HAVE ADJUSTMENTS TO HANDLE 4" TO 4.5" WIDE ROLLS. ELEVATOR & TOP PLUNGER. CRIMPER & SIDE PLUNGERS. EJECT ARMS. WITH CUPS THAT ARE PRESENTLY IN THE MACHINE, WILL HANDLE ROLLS FROM 4.25 TO 4.75 DIAMETER. IF DIFFERENT DIAMETER ROLLS ARE NEEDED TO BE WRAPPED, THEN THE PURCHASE OF DIFFERENT SIZE CUPS CAN BE MADE. TYPICAL OPERATING SPEED FOR LAWTON WRAPPER IS 60 TO 65 WRAPS PER MINUTE; THIS IS DEPENDENT UPON OPERATORS SKILL, ROLLS OF TISSUE, WRAPPER MATERIAL, ENVIRONMENT & CONDITION OF MACHINE. 2 HP AC MOTOR, 460 VOLTAGE. LINCOLN OILER. GOOD MECHANICAL CONDITION.

HAMBLET 20-52 HEAVY-DUTY SHAFTLESS, ROLL PICKUP, SINGLE POSITION UNWIND. MAXIMUM ROLL DIAMETER, 84. 1000 FEET PER MINUTE. UNWIND CAN BE MADE WIDER EASILY. DEPENDENT UPON WEIGHT OF EACH ROLL. EACH SIDE HAS APPROXIMATELY 24" OF LEAD SCREW ADJUSTMENT. CAN CUT THE PLATE CONNECTING THE TWO SIDES & MAKE WIDER TO TAKE WIDER ROLLS. IT WILL CHANGE MINIMUM WIDTH OF ROLL. COULD GO AS WIDE AS 90". HEAVY-DUTY SHAFTLESS UNWIND STAND. 12 CORES. 8000 LB. ROLLS. AS SET UP TODAY, 20 TO 52 WIDE ROLLS. HAS PUSH-BUTTON MOTORIZED WIDTH ADJUSTMENT AND LATERAL ADJUSTMENT. MANUAL SKEW ADJUSTMENT. HAS SOUTHWORTH LSN-36 LIFT TABLE, 36" RISE, ROLL LIFTING SYSTEM TO LIFT ROLL UP TO UNWIND POSITION. NO HOIST IS NEEDED. SELF-CENTERING OF THE ROLL. THIS UNWIND HAS BEEN INLINE WITH HAMBLET SHEETER. WITCHITA AIR BRAKE. MANUAL CONTROL OF BRAKING SYSTEM WITH REGULATOR. HAS 2 FT. X 5 FT. LIFT TABLE; LIFT ROLLS UP TO CHUCKS. EACH SIDE HAS OWN MOTOR & SWITCH TO BRING IN / OUT. UNWIND COULD BE PUT INLINE WITH SHEETER, SLITTER REWINDER, LAMINATOR, COATER, DIE CUTTER & PRINTER. TAKES UP VERY LITTLE SPACE.

20 WOLVERINE CUBLINE MODEL CLRE-N-1310X 21-3, 3-COLOR FLEXOGRAPHIC INLINE PRINTING PRESS. 20" PRINT - 20 WOLVERINE CUBLINE MODEL CLRE-N-1310X 21-3, 3-COLOR FLEXOGRAPHIC INLINE PRINTING PRESS. 20" PRINT WIDTH. 10 TO 30 REPEAT RANGE. 3-COLOR STATIONS BUILT ON 4-COLOR FRAME. THIRD COLOR STATION IS MISSING RUBBER ROLL & SYSTEM THAT HOLDS INK PAN; OTHERWISE, STATION IS COMPLETE. 360 DEGREE REGISTRATION CONTROL ON EACH COLOR STATION. SIDE REGISTER CONTROL ON PRINT CYLINDERS. HYDRAULICALLY-OPERATED FOUNTAIN DRIVE WITH INDIVIDUAL START / STOP AND VARIABLE SPEED CONTROL FOR EACH COLOR STATION. HYDRAULIC THROW OFF TO SIMULTANEOUSLY SEPARATE PLATE CYLINDER FROM WEB & INK ROLLER. CERAMIC ANILOX ROLLS. 1/4 PITCH GEARING. 230 / 460 VOLTAGE, 3 PHASE, 60 CYCLE. MACHINE INCLUDES 5 HP LOUIS ALLIS AC VARIABLE SPEED DRIVE. DEMOUNT PLATE CYLINDERS ARE USED. 400 FEET PER MINUTE. MOST RECENTLY PRINTING WATER-BASED INKS. PLATE CYLINDERS AUTOMATICALLY RISE TO SIMULTANEOUSLY SEPARATE FROM THE WEB & INK ROLLS WHEN PRESS IS AT STOP. TWIN DISC AIR CLUTCHES. HYDRAULIC PUMP & RESERVOIR INCLUDED. TWO 20" WIDE, 4.3 DIAMETER PRINT CYLINDERS. 21.5" WIDE, 8 DIAMETER IMPRESSION CYLINDER. 22.75" WIDE, 3.5 DIAMETER ANILOX ROLL. 22.75" WIDE, 4 DIAMETER RUBBER ROLL. MANUAL REGISTRATION CONTROL DONE ON EACH PRINT STATION. THIS PRINTER WAS ORIGINALLY A ROLL-TO-ROLL PRINTER; IS NOW SET UP TO BE PUT INLINE. COULD BE PUT INLINE WITH PAPER BAG MACHINE, POLY BAG MACHINE & EXTRUDER. HAS PULLEY WHICH DRIVES PRINT STATION.

TIDLAND CLASS I & II SHEAR KNIVES

NORDSON PARTS, EMP, DRIVES, METERS, PANELS, SCREENS, ETC. ON (4) SECTIONS OF SHELVING

ASSORTED ELECTRICAL CABINETS

PNEUMATIC CORE PLUGS, SHAFT MOUNT (TAG READS 188A) - PNEUMATIC CORE PLUGS, SHAFT MOUNT ON 2 (TAG READS 188A)

1980 WOLVERINE 41-1 HLRE HYDRALINE 1-COLOR STACK FLEXOGRAPHIC PRINTING PRESS FOR INLINE OPERATION. 41" WEB WIDTH. 40" PRINT WIDTH. ONE COLOR PRINT STATION. HAS HARRIS BRUNO ENCLOSED DOCTOR BLADE ASSEMBLY, CERAMIC ANILOX ROLL. PRESS WAS LAST PRINTING ON FILM, CELLOPHANE, PVC, POLYPROPYLENE. 10 PITCH GEARING. CAPABLE OF PRINTING ON PAPERS, FILMS, LAMINATIONS, BOARD, NONWOVENS, FABRICS. COULD BE PUT INLINE WITH BLOWN FILM EXTRUDER, PAPER BAG MACHINE, SHEETER, SLITTER REWINDERS, COATERS, LAMINATORS. 10-40" REPEAT RANGE. STAINLESS STEEL DRIP PAN. PRESS FEATURES MANUAL REGISTRATION CONTROL AT PRINT STATION. SIDE REGISTER CONTROL AT PRINT STATION, 360 DEGREE REGISTRATION. YOU CAN SET THE REGISTRATION WHILE MACHINE IS RUNNING. INDEPENDENT SPEED CONTROL OF INK ROLLERS. VARIABLE SPEED HYDRAULIC FOUNTAIN DRIVE AT EACH PRINT STATION. WATER-BASED INKS. EQUIPPED WITH A FREE-WHEELING CLUTCH WHICH ALLOWS THE TRANSFER & INK ROLLERS TO ROTATE CONTINUOUSLY POWERED BY HYDRAULIC DRIVE DURING THE SHUT DOWN I.E. HAS CONSTANT ROTATING INK OF THE ANILOX ROLLS WHEN THE MACHINE IS IN AN OFF POSITION. HAS HYDRAULIC PUMP TO OPERATE CONSTANT ROTATION & AUTOMATIC PICKUP OF PLATE CYLINDER WHEN MACHINE STOPS. (4) PRINT CYLINDERS INCLUDED, TWO 4.5" DIAMETER & TWO 6.04" DIAMETER PRINT CYLINDERS. 41.5" CHROME-PLATED IMPRESSION CYLINDER, 8" DIA. 42" WIDE ANILOX ROLL, 5" DIA. AUTOMATIC PLATE CYLINDER LIFT DURING STOP PLATE CYLINDERS AUTOMATICALLY LIFTED. INCLUDES HYDRAULIC TANK & RESERVOIR. MECHANICAL SPEED OF HLRE 700 FPM. PULLEY FOR DRIVE CONNECTION. MACHINE IS IN GOOD MECHANICAL CONDITION. THIS PRINT STATION COULD BE PUT ON TOP OF AN EXISTING WOLVERINE PRINT STATION TO MAKE ADDITIONAL COLORS.

VETTER 1600 KG. PORT. GANTRY W/(2) VETTER 750 KG. ELEC. HOISTS, APPROX. 16' SPAN S/N: 900786.1

WINDMOLLER & HOLSCHER QMS-945 FLEXOGRAPHIC INLINE TAILEND PRINTING PRESS. 2-COLOR ON 3-COLOR FRAME. SOME PARTS TO 3RD PRINT STATION. 26 WEB WIDTH. 25 PRINT WIDTH. 26 RUBBER ROLL. 26.5 ANILOX ROLLS. 27.5 IMPRESSION CYLINDERS. 9 TO 31.5 REPEAT RANGE. QMS-945 PRINTER IS ALSO REFERRED TO AS ALINA X30 FLEXOGRAPHIC TAILEND PRINTER. 30 DRYING DISTANCE BETWEEN EACH COLOR. 10 PITCH GEARING. TWO PRINT CYLINDERS, 5.3 DIAMETER INCLUDED. DESIGNED WITH CENTRAL BULLGEAR WHICH HELPS TO ASSURE QUALITY PRINTING & GOOD REGISTER CONTROL. TYPICAL OPERATING SPEED, 600 FEET PER MINUTE. SPEED DEPENDS UPON MATERIAL & DRYING CAPABILITY OF THE INK USED & SUBSTRATE PRINTED. MOST RECENTLY PRINTING WITH WATER-BASED INKS. CYLINDER THROWOFF WHICH IS DONE MANUALLY. SOLID CONSTRUCTION & HEAVY-DUTY SIDE FRAMES ASSURE VIBRATIONLESS, HIGH-SPEED OPERATION & QUALITY PRINTING. SHAFT DRIVEN. MANUAL 360 DEGREE REGISTRATION CONTROLS. PRINTING PLATE CYLINDER IS MOVED FROM SIDE-TO-SIDE MANUALLY TO ADJUST FOR CROSS REGISTER. BOTH ADJUSTMENTS ARE MADE WHILE THE PRESS IS RUNNING. INFEED DRAW ROLLER SYSTEM LOCATED AHEAD OF THE FIRST PRINTING UNIT, CONSISTING OF A DRIVEN STEEL ROLLER & RUBBER-COVERED ROLLER WHICH IS RIDING AGAINST THE STEEL ROLL WITH A VARIABLE AMOUNT OF PRESSURE. WEB IS FED INTO THE PRINTER FROM THE BOTTOM. 6 DIAMETER IMPRESSION CYLINDERS. 5 DIAMETER ANILOX ROLLS. 5 DIAMETER RUBBER ROLLS. MANUAL SIDE SHIFTING OF THE ENTIRE PRINTER LEFT & RIGHT 4. THIS PRINTER CAN BE USED WITH PAPER BAG MACHINES, POLY BAG MACHINES, LAMINATORS, SHEETERS, ETC. MOST RECENTLY WAS INLINE WITH PAPER BAG MACHINE. THIRD COLOR STATION IS MISSING ONE RUBBER ROLL & BEARING FOR RUBBER ROLL. NEW BEARINGS ON RUBBER & ANILOX ROLLS. HAS CHANGE GEAR SYSTEM. REFURBISHED RECENTLY.

28 SINGLE POSITION UNWIND. CUSTOM-BUILT. WAS INLINE WITH CALENDER OPERATING AT APPROX. 15 FEET PER MINUTE. 28 WEB WIDTH. 28 DIAMETER ROLLS. ONE 3 AIR STEEL UNWIND SHAFT. 29.5 WIDE IDLERS. 2.75 DIAMETER IDLERS. ALL ALUMINUM IDLERS. SINGLE POSITION UNWIND. HAS 6 ELECTRIC BRAKE WITH ALTEC TC 818 TENSION CONTROLLER WITH TENSION ROLL AND TRANSDUCERS FOR AUTOMATIC CONTROL OF TENSION. DCM EDGE GUIDING SYSTEM WITH ELECTRIC EYE AND ACTUATOR FOR MOVING UNWIND +/- 3. AIR-LOADED SPLICING SYSTEM. FEMALE DRIVEN KNIFE BAR. NO FEMALE KNIVES. 1/2 HP DRIVE MOTOR TO DRIVE FEMALE KNIFE BAR. ONE MOTO MALE KNIFE SHEAR CUT KNIFE, TANGENTIAL SHEAR. WEB CLEANER DRIVEN BY TWO 15 WATT DRIVE MOTORS. SET UP FOR 220 VOLT, 50/60 CYCLE GEAR MOTORS. UNWIND BUILT IN JAPAN BY ELECTROVAYA MACHINE BUILDING DIVISION. WAS INLINE WITH CALENDER. EXCELLENT CONDITION. REWINDING FILM.

ARROW 325 SLITTER REWINDER, MINIMUM GAP REWIND, CENTER REWIND, CANTILEVERED REWIND SHAFTS, DUPLEX SLITTER REWINDER. DESIGNED FOR NARROW WIDTH SLITTING. SERIAL # 13502. MINIMUM GAP CENTER REWIND. MOVEABLE REWIND SHAFTS WHICH ALLOW FOR ADJUSTABLE MINIMUM GAP REWINDING CAPABILITY FOR NARROW SLITS. MINIMUM GAP REWINDING ALLOWS FOR SHORT DISTANCE FROM IDLER ROLL TO THE REWINDING ROLL. SHORT DISTANCE FROM SLITTING SECTION TO THE REWINDING ROLL. CANTILEVERED REWIND SHAFTS. EASY UNLOADING OF REWOUND ROLLS. EACH REWIND STATION IS DRIVEN THROUGH A SENSITIVE SLIP CLUTCH. CANTILEVERED REWIND SHAFT MOUNTED ON A PIVOTED BRACKET TO PERMIT LOCATION OF THE REWIND IN ORDER TO MINIMIZE THE DRAW DISTANCE BETWEEN REWINDING ROLL AND IDLER ROLL. THIS ALLOWS NARROW SLITS TO BE MADE. ATTACHED UNWIND, 40 DIAMETER ROLL. ONE 4 AIR UNWIND SHAFT. 6 DIAMETER AIR BRAKE. FIFE AUTOMATIC EDGE GUIDING SYSTEM TO MOVE UNWINDING ROLL LEFT & RIGHT +/- 4. PNEUMATIC SENSOR. SCORE CUT SLITTING. (8) AIR-LOADED SCORE CUT KNIFE HOLDERS, (7) KNIVES. RAZOR SLITTING IN A COMB SYSTEM. .05 GROOVES. ONE GROOVED ROLL, SET UP FOR .035 SPACING. GROOVED ROLL IS DRIVEN. 3 DIFFERENTIAL REWIND SHAFTS. AIR-LOADED SINGLE ZONE DIFFERENTIAL REWINDING. CAN ALSO DO LOCKED CORE REWINDING. EACH REWIND POSITION HAS ITS OWN AIR CLUTCH. 24 DIAMETER REWIND. 7.5 HP RELIANCE DC DRIVE MOTOR. RELIANCE VARIABLE SPEED DC DRIVE, MODEL MAX PAK. 208 VOLT, 3 PHASE, 60 CYCLE. 44 WIDE ROLLS. WHEN USING RAZOR SLITTING, .25 MINIMUM SLIT WIDTH. WHEN USING SCORE CUT SLITTING, .5 MINIMUM SLIT WIDTH. MANUALLY CONTROL MINIMUM GAP. REWIND ARMS / SHAFTS MOVE OUT AS THE DIAMETER OF THE REWINDING ROLL INCREASES. DISTANCE FROM THE IDLER ROLL TO THE REWINDING ROLLS KEPT TO A MINIMUM. MECHANICAL COUNTER. MACHINE IS CAPABLE OF SLITTING & REWINDING PRESSURE-SENSITIVE TAPES, LABEL STOCK, LAMINATIONS, PAPER, TEXTILE PRODUCTS, NONWOVENS, FILMS, FOILS, LIGHT & HEAVY-GAUGE FILMS. CANTILEVERED REWIND SHAFTS ASSIST WITH QUICK LOADING & UNLOADING OF ROLLS. 500 FEET PER MINUTE WEB SPEED. TIMING BELTS USED.

ALLEN BRADLEY, DIRECT LOGIC, GE PLC'S & SCREENS

1980 DUSENBERY 260 FS DUPLEX CENTER SURFACE REWIND SLITTING & REWINDING MACHINE S/N: 57690. 24" MAXIMUM REWIND ROLL DIAMETER. 1500 FPM. 2" MINIMUM SLIT WIDTH. DUSENBERY SHEAR CUT SLITTING. TANGENTIAL SHEAR CUT. (5) MALE KNIVES. (90) FEMALE KNIVES. CAN EASILY RAZOR SLIT IN AIR. MALE KNIFE BAR CAN HAVE RAZOR HOLDERS INSTALLED. NO UNWIND. 3 MOTOR DRIVE, DC VARIABLE SPEED. (2) 15 HP MOTORS; ONE ON EACH REWIND POSITION. 20 HP MOTOR; DRIVES PULL ROLLS & SURFACE BEDROLL. RELIANCE MOTORS & CONTROLLERS. DYNAPAR 2 PRE-SET COUNTER. PRECISION TRIM CHOPPER WITH 1 HP MOTOR INCLUDED. (3) 3 DIFFERENTIAL REWIND SHAFTS, 1-ZONE, AIR-LOADED DIFFERENTIAL REWIND. AIR-OPERATED SINGLE DIFFERENTIAL REWIND TENSION CONTROL. REWIND ARMS WITH ADJUSTABLE AIR CYLINDERS FOR DOWN PRESSURE CONTROL USING BALANCING PRESSURE SYSTEM. PLAIN STEEL WINDING DRUMS. RELIANCE 3-MOTOR SCR DRIVE FOR SLIP CORE OR LOCKED CORE WINDING. SLOW DOWN SYSTEM USING REWIND ARM POSITION TO SENSE DIAMETER OF REWINDING ROLL. HAS BEEN SLITTING & REWINDING FLEXIBLE PACKAGING MATERIALS, LAMINATIONS.

RELIANCE ELECTRIC VZ 3000 SERIES INDUCTION AC SERVO DRIVE. NEW, NEVER USED.

BRIDGEPORT VERT. MILL, 32" P.F. TABLE, 3 PH. S/N: 46150

ABB ACS800-U1-0040-5+P901 DRIVE

POWERFLEX 755 20 HP DRIVES

ASST. TRANSFORMERS

POTDEVIN SINGLE POSITION UNWIND STAND. 60" DIAMETER ROLL. 3" UNWIND SHAFT. MANUAL SIDE SHIFTING LEFT / RIGHT +/- 2. FLOOR PICKUP. ELECTRIC MOTOR. BRAKING OF ROLL USING PADDLES. WAS INLINE WITH POTDEVIN PAPER BAG MACHINE.

DRIVE CABINET W/ABB ACS600 DRIVE, DELTA S1 DRIVE, CONTROL PANEL W/ALLEN BRADLEE PANEL VIEW 550 READ OUT

ROTARY DIE CUTTER. WAS INLINE WITH WEBER 7 BAG MACHINE DIE CUTTING WINDOW FOR POTATO BAGS. LINESHAFT DRIVEN. 2-ROLL SYSTEM.

2001 DUNCAN TECHNOLOGIES 88 TEXTILE INSPECTION WINDER S/N: DT10014-01. IDLERS IN MACHINE ARE 91" WIDE, 4" DIAMETER. SINGLE POSITION UNWIND & SINGLE POSITION CENTER REWIND, SET UP FOR 3 CORES WITH 4 ADAPTERS. CONTROLS ARE AIR BRAKE PRESSURE, ELECTRONIC EDGE GUIDING, PNEUMATIC CORE LOADING. 230 VOLT, SINGLE PHASE. OVERHEAD INSPECTION LIGHT. BACK BOARD INSPECTION LIGHT. BACK BRAKE, FRONT CLUTCH, BACK CLUTCH, FRONT BRAKE, DRIVE FORWARD & REVERSE. RED LION COUNTER. TAIL OUT SENSOR. COUNTER CAN BE RUN ON MANUAL OR AUTOMATIC. SPRINT DRIVE, DC, SINGLE PHASE, 230 VOLT, SINGLE MOTOR, VARIABLE SPEED. INCLUDES MANUAL. MANUFACTURER OF EDGE GUIDE IS EL. MODEL 3600XRI, SINGLE PHASE, DC MOTOR CONTROLLER. GEMINI 4100 6-DIGIT PRESET COUNTER. SPEEDS, 10 TO 20 YARDS PER MINUTE. SINGLE POSITION UNWIND. SINGLE POSITION REWIND. MACHINE IS REVERSIBLE. HAS 10 STROKE ON EDGE GUIDING SYSTEM. UNWIND & REWIND WILL ACCEPT 24" DIAMETER ROLLS. PNEUMATIC CHUCKING. DOUBLE E CHUCKS. SHAFTLESS DESIGN FOR UNWIND & REWIND. CAN VARY THE WEB WIDTH. UNWIND HAS MANUAL CHUCKING. AIR BRAKE. AIR CLUTCH. EL EDGE GUIDE SYSTEM WITH ELECTRIC EYE. AIR-LOADED CHUCKING ON REWIND. INSPECTION LIGHT ABOVE & BEHIND MATERIAL. FOOT PEDAL CONTROL FOR START / STOP. ADJUSTABLE S-WRAP TENSION BAR ASSEMBLY. EACH UNWIND / REWIND POSITION HAS A CLUTCH & BRAKE WHICH ALLOWS THE MACHINE TO OPERATE BACK & FORTH. MACHINE IS IN EXCELLENT MECHANICAL CONDITION. OPERATORS MANUAL, ELECTRICAL DIAGRAMS, PRINTS. CAN BE SHOWN IN OPERATION.

20 HP DRIVES

2005 NORDMECCANICA 4-ROLL, CHILL ROLL / HEAT ROLL SYSTEM. 64" WIDE IDLERS. THIS CHILL ROLL / HEATED ROLL SECTION WAS INLINE WITH A LAMINATOR. DIAMETER OF EACH OF THE FOUR ROLLS IS 9.5 DIAMETER. ROLLS CAN BE HEATED OR CHILLED. INCLUDED IS STERLCO HOT-OIL HEATER, MODEL M2B-2016-MI. SET UP ON 230 VOLT, 60 CYCLE, 3 PHASE. STERLCO CAN BE USED FOR HEATING OIL, WHICH IS THEN PUMPED TO THE FOUR ROLLS. FOUR ROLLS ARE MOUNTED IN A FRAME. ALSO INCLUDES PARTS FOR UNWIND. FORMER OWNER WAS USING 4-ROLL SYSTEM AS A PRE-TREATING SYSTEM.

MAGPOWER DFE CLEVELAND KIDDER TENSION SYSTEMS, VARIOUS LOAD CELLS, MONTALVO TENSION SYSTEMS, LOAD CELLS, COUNTERS, SENSORS

1997 SALWASSER R-101 CASEPACKER S/N: 98033347. INCLUDES INFEED LANE, MANUAL MAGAZINE FEEDER (300) CASES IN THE MAGAZINE. (4) CASES PER MINUTE MAXIMUM CYCLE SPEED. AB/SLC/504 ELECTRONIC PLATFORM. WHAT IS BEING SOLD IS A CARTONER WITH CONVEYORS GOING TO SALWASSER AUTOMATIC CASEPACKER. LOVESHAW 16B CASE SEALER. INCLUDES PACK AIR CONVEYORS, APPROXIMATELY 60-FEET. 14 WIDE POWERED BELT CONVEYOR. 10 WIDE BELT WITH CONTROLS. CONVEYORS TAKE PRODUCT FROM JONES CARTONER, DELIVER TO SALWASSER. THESE UNITS WERE INLINE, IN OPERATION. INCLUDES CHANGE PARTS FOR SALWASSER.

SCORE CUT KNIVES & BLADES APPROX. 200"

L-TEC 225 PORT. WELDER ST-23 MIG TORCH S/N: B89G-00826

(2) POWERFLEX 755 DRIVES (BOTH DRIVES ARE 5 HP)

20 BIRCH BROTHERS 2-ROLL CALENDER. THIS CALENDER WAS UNWINDING, CALENDERING NONWOVENS, SLITTING AND THEN REWINDING ROLLS. WAS USED IN LAB APPLICATION. REEVES VARIABLE SPEED DRIVE. AC MOTOR. SET UP ON 220/440 VOLTAGE, 3 PHASE, 60 CYCLE. VARY THE SPEED MECHANICALLY. TYPICAL OPERATING SPEED 100 FPM. MAXIMUM DIAMETER ROLL ON UNWIND IS 40. ONE UNWIND SHAFT WITH 3 CORE PLUGS. SINGLE POSITION UNWIND. MANUAL EDGE GUIDING PROVISION TO SHIFT ROLL LEFT & RIGHT +/- 1. AFTER UNWIND, HAS CALENDERING SYSTEM. (2) CALENDER ROLLS ARE IDENTICAL IN DIMENSIONS, 24 FACE WIDTH, 9 DIAMETER CALENDER ROLLS. BOTH ROLLS WILL ACCEPT HEATED OIL. MOST RECENTLY HAS NOT BEEN USED AS A HEATED CALENDER, JUST PRESSURE. BOTTOM OF (2) ROLLS IS HYDRAULICALLY LOADED UP INTO THE TOP ROLL WHICH IS STATIONERY. THERE ARE (2) HAND PUMPS, SIMPLEX MODEL P42. MAXIMUM CAPACITY 10,000 PSI. 20-TON CAPACITY. 2 THICK SIDE FRAMES. SIMCO STATIC ELIMINATOR SYSTEM. 2-DRUM SURFACE REWINDER WHICH IS DRIVEN OFF OF THE MAIN DRIVE. HAS PIV TO CONTROL THE SPEED OF THE BEDROLLS. ONE 2 ALUMINUM REWIND SHAFT. ONE 3 STEEL REWIND SHAFT. 20 MAXIMUM REWIND DIAMETER. SCORE CUT SLITTING AGAINST BEDROLL. 1 MINIMUM SLIT WIDTH. (8) AIR-LOADED SCORE CUT KNIVES. MACHINE HAS BEEN USED ON NONWOVENS PRODUCTS.

AMERICAN FAN OVP-7-08F-30A TRIM BLOWER SYSTEM. THIS IS A TRIM BLOWER SYSTEM THAT WAS INLINE WITH A 110 SLITTER REWINDER, TRIMMING THE EDGES. SLITTER WAS OPERATING AT 4000 FEET PER MINUTE. TRIM REMOVAL FOR PAPER & LIGHT BOARD. TRIM BLOWER HAS 50 HP BALDOR MOTOR, 230 / 460 VOLT, 3 PHASE, 60 HERTZ. INCLUDED IS AEROCUSTIC CORP. MODEL 12TA-2A TUBULAR SILENCER, 4/05. HAS QUICK VAC CONTROL BOX; CONTROLS VALVE. HAS INTAKE SILENCER.

FIFE GUIDES

LEMBO 70 SINGLE POSITION UNWIND. MAXIMUM DIAMETER ROLL, 50". ONE 3" AIR UNWIND SHAFT. 10" MONTALVO AIR BRAKE, FAN COOLED. MANUAL CHUCKING OF UNWIND SHAFT. PUSH-BUTTON EDGE GUIDING, LEFT / RIGHT, +/-6. LINEAR ACTUATOR. CURRENTLY SET UP WITH AIR SHAFT. UNWIND COULD BE USED AS A SHAFTLESS UNWIND; NEED TO ORDER CHUCKS. UNWIND WAS INLINE WITH SLITTER REWINDER OPERATING AT 2000 FEET PER MINUTE

ASST. DIAPHRAM PUMPS

2002 PROPHETEER 1300 L SINGLE COLOR FLEXOGRAPHIC PRINTING PRESS. 13" PRINT WIDTH. 40" DIAMETER UNWIND. 40" DIAMETER REWIND. 6 TO 15 REPEAT RANGE. CAN PURCHASE ADAPTOR TO INCREASE TO 24 REPEAT. MODEL 1300 L. SERIAL # 02189. AC VARIABLE SPEED DRIVE. ABB CONTROLLER, MODEL ACS 600, 230 VOLT, 3 PHASE, 60 CYCLE. 5 HP AC MOTOR, ABB. 15 WIDE IDLER ROLLS THROUGHOUT THE MACHINE. 500 FPM. 3 AIR SHAFTS ON UNWIND & REWIND. REWIND IS CANTILEVERED CENTER REWINDER, SINGLE POSITION. UNWIND HAS POWER ROLL LIFT. DANCER REGULATES BRAKE. SPLICE TABLE WITH PNEUMATIC CLAMPS. UNWIND TENSION SYSTEM. PTC-100 AUTOMATIC TENSION CONTROLLER. MAGNETIC BRAKE. ELECTRONIC AUTOMATIC EDGE GUIDE CONTROLS THE WEB. ACCUWEB MICRO 1000 CONTROLLER. SINGLE FLEXO PRINTING STATION. CERAMIC ANILOX ROLLS. (3) PRINT CYLINDERS. 1/8 PITCH GEARING. WATER-BASED INKS. 14" LONG DRYER BOX WITH ELECTRIC HEATER & BLOWER. DRIVEN SHEAR CUT SLITTING SECTION INLINE. BOWED ROLL AFTER SLITTING, BEFORE REWIND. CANTILEVERED CENTER REWINDER. RED LION COUNTER. BIJUR AUTOMATIC OIL LUBRICATION SYSTEM. TANGENTIAL SHEAR CUT. .75 MINIMUM SLIT WIDTH. (7) MALE & (7) FEMALE KNIVES. DRYING IS HOT AIR, HIGH VELOCITY. LINEAL WEB DIRECTION RUNNING REGISTER. LATERAL ACROSS THE WEB RUNNING REGISTER. COUNTER. QUICK-CHANGE ANILOX ROLL, METERING ROLL & DOCTOR BLADE. CONSTANT ROTATING INK AND AUTOMATIC PLATE CYLINDER THROWOFF WHEN PRESS STOPS. THIS MACHINE IS DESIGNED FOR LABELS, LAMINATIONS, PAPER, LIGHT BOARD & FILM.

ASSORTED MOTORS, VARIOUS HP'S, 1 HP - 25 HP

LP STORAGE CAGES (NO TANKS)

APPROX. (23) ASST. C-CLAMPS, VISE, STEEL BENCH

57 SINGLE POSITION UNWIND STAND. THIS UNWIND WAS INLINE WITH A SHEETER UNWINDING TISSUE PAPER. COULD BE USED FOR UNWINDING FILM, PAPER, NONWOVENS & FOIL. 57 MAXIMUM WEB WIDTH. 20 DIAMETER ROLL. ONE 3 AIR LUG UNWIND SHAFT. HAS FLOOR PICKUP CAPABILITY TO PICK THE UNWINDING ROLL UP OFF OF THE FLOOR. PNEUMATIC CYLINDERS ARE USED. HAS BAND BRAKING. AIR ADJUSTED MANUAL ADJUSTMENT BAND BRAKE. NO EDGE GUIDING. NO SKEW ADJUSTMENT. MACHINE IS IN GOOD MECHANICAL CONDITION.

30 SCORE CUT SLITTING SECTION. THIS SLITTING SECTION WAS INLINE WITH A FLEXOGRAPHIC PRINTING PRESS. WAS MOUNTED BEFORE REWIND. BELIEVE MANUFACTURED BY DIENES. 32 WIDE HARDENED STEEL ROLL, 3.5 DIAMETER HARDENED STEEL ROLL; THAT IS THE SCORING ROLL. CAN BE DRIVEN. (33) DIENES AIR-LOADED SCORE CUT KNIVES, .5 WIDE. TWO DOVETAIL BARS SO BACK-TO-BACK SCORE CUT SLITTING CAN BE DONE. EACH KNIFE HAS ITS OWN REGULATOR. FORMER OWNER WAS DOING 1 WIDE SLITS OF PAPER. ALL (33) KNIVES CAN BE USED AT THE SAME TIME. IN ADDITION, HAVE SECOND SCORE CUT KNIFE SYSTEM WITH KNIVES MANUFACTURED BY EMT; THERE ARE A TOTAL OF (5) AIR-LOADED KNIVES, 2 WIDE. THESE KNIVES HAVE THEIR OWN REGULATOR. FORMER OWNER WOULD HAVE MACHINE SET UP FOR TWO DIFFERENT SLIT WIDTHS. EASY TO CHANGE BETWEEN THE DIFFERENT SLIT WIDTHS. EMT KNIVES ARE BAR MOUNTED. IDLERS IN SCORE CUTTING SYSTEM ARE 3 IN DIAMETER, ALUMINUM. FRAME FOR THE SCORE CUT SYSTEM IS 44.75 WIDE. CAN DO VERY NARROW SLITTING WHEN USING THE TWO DOVETAIL SETUPS; AS NARROWER AS .25 WIDE SLITS. THE PRINTING PRESS THAT SCORE CUT SYSTEM WAS INLINE WITH WAS OPERATING AT APPROXIMATELY 500 FEET PER MINUTE. WELL-BUILT SYSTEM. EASY TO INSTALL.

RELIANCE ELECTRIC FLEXPAK 3000 DC VARIABLE SPEED DRIVE. NEW, NEVER INSTALLED. 230 / 460 VOLT.

LEMPCO SERIES 341 HYD. H-FRAME PRESS, 9" RAM, 60 TON, 3 PH. S/N: 348

ASST. PALLET SHELVING (NO CONTENTS)

30" WIDE LAMINATING STATION. 31.5" WIDE, 4" DIAMETER STEEL ROLL WHICH IS DRIVEN BY GTR .75 KW, 220 VOLT, 3 PHASE, 60 HERTZ AC MOTOR. STEEL ROLL OF LAMINATING NIP IS DRIVEN. 31.5" WIDE, 4" DIAMETER RUBBER-COVERED ROLL; AIR-LOADED DOWN ONTO THE STEEL ROLL. HAS MANUAL GAP ADJUSTMENT TO ADJUST THE DISTANCE BETWEEN THE TWO ROLLS. SIMCO STATIC ELIMINATOR BAR. TWO STEEL IDLER ROLLS. HAS PARKER MODEL 690 PLUS SERIES AC INTEGRATOR DRIVE, SET UP FOR 230 VOLT, 3 PHASE, 60 CYCLE. THIS IS A DRIVEN LAMINATING NIP, AIR-LOADED, CUSTOM-BUILT. WAS INLINE WITH COATING LINE. UNWINDING FILMS.

ASST. NUTS, BOLTS, HARDWARE, ETC. ON (4)

230,460,600 VOLT PLUGS, SAFETY SWITCHES, RELAYS, MOTOR STARTERS, SQUARE D PUSH BUTTONS, TIMER RELAYS, HEATER CONTROLS, SIEMENS PUSH BUTTONS

9 SECTIONS OF YELLOW PALLET RACKING

ENCO 110-2032 LATHE, 3 & 4 JAW CHUCKS, TOOL POST W/HOLDERS S/N: 88458