Surplus CNC Fabrication Industrial Equipment Multiple Locations
Category: METALWORKING & FABRICATION EQUIPMENT
Total Lots:
502
Total Sales:
🔒 Subscribe
Lot Price Distribution
| Year | Make | Model | Lot Description | Hammer Price | |
|---|---|---|---|---|---|
|
2004 | MILLTRONICS | VM-22 |
2004 MILLTRONICS VM-22 VERTICAL MACHINING CENTER X-AXIS TRAVEL: 40 INCH Y-AXIS TRAVEL: 22 INCH Z-AXIS TRAVEL: 26 INCH TABLE LENGTH: 45 INCH TABLE WIDTH: 24 INCH MACHINE LENGTH: 120 INCH MACHINE WIDTH: 96 INCH MACHINE HEIGHT: 108 INCH APPROX MACHINE WEIGHT: 16,000 LBS EQUIPPED WITH: TROYKE 4TH AXIS INDEXER CENTURION 7 CNC CONTROLLER 8 INCH CHUCK
|
🔒 Subscribe |
|
|
EDWARDS |
EDWARDS IRON WORKER, 25 TON S/N: 1049141W25
|
🔒 Subscribe | ||
|
|
2017 | OKUMA | 2SP-250H |
2017 OKUMA 2SP-250H TWIN SPINDLE TWIN TURRET CNC LATHE - TWIN SPINDLE TWIN TURRET CNC TURNING CENTER - CHIP CONVEYOR, ROBOT LOADER, TRANSFORMER, MAX TURNING DIAMETER: 8.66 INCH MAX TURNING LENGTH: 5.91 INCH TRAVEL X-AXIS: 5.91 INCH Z-AXIS: 6.10 INCH SPEED RANGE: 50-4500 RPM TURRET TYPE: V12 NC MOTOR SPINDLE DRIVE: 15/10 HP EQUIPPED WITH: OKUMA OSP-P300LA CONTROL ROBOT LOADER CHIP CONVEYOR TRANSFORMER 220/480, 3 PHASE, 60 HZ, 55.1 KVA, FULL LOAD CURRENT 144.7 / 66.3 A, LARGEST MOTOR RATING 48 A, INTERRUPTING CAPACITY 30 / 10 KA, SCCR OF CONTROL PANEL 10 KA MACHINE POWERED ON WITHOUT ANY MAJOR ALARMS HAD TO SET THE COOLANT LOW INPUT AND AIR PSI INPUT IN ORDER TO MOVE THE AXIS MACHINE HAD A BATTERY LIFE ALARM DUE TO BEING OUT OF SERVICE, BACKUPS PERFORMED THE MACHINE HAD A BROKEN LOAD CABLE TRACK ON TOP AND WAS MISSING THE CHUCKS R-L SIDE AXIS AND SPINDLE OPERATE NORMALLY LOADER AXIS OPERATE NORMALLY MACHINE WAS TEST WITHOUT STOCKER TABLE INSTALLED AND APPEARS THAT WHEN IT WAS IN OPERATION THE PARTS WERE PLACED ON A CONVEYOR. INBOUND OUTBOUND.
|
🔒 Subscribe |
|
|
CROWN | 15BT |
CROWN PALLET JACK, MODEL 15BT, S/N: 1A194571
|
🔒 Subscribe | |
|
|
ROL-LIFT |
ROL-LIFT PALLET JACK, 1000 LBS, S/N: CB4598
|
🔒 Subscribe | ||
|
|
SPEED-CUT | 21C.100.03387 |
SPEED-CUT ABRASIVE CUTOFF MACHINE, S/N: 21C.100.03387
|
🔒 Subscribe | |
|
|
CLARK | EWP45 |
CLARK EWP45 PALLET JACK
|
🔒 Subscribe | |
|
|
JMT | PBM 50 |
JMT PBM 50 ANGLE, FLAT BAR AND ROUND STOCK BENDER S/N: N7119
|
🔒 Subscribe | |
|
|
MARVEL | SERIES 8 MARK II |
MARVEL SERIES 8 MARK II PIPE SAW
|
🔒 Subscribe | |
|
|
2001 | MITUTOYO | BHN706 |
2001 MITUTOYO BHN706 CNC COORDINATE MEASURING MACHINE X AXIS: 28 INCH Y AXIS: 24 INCH Z AXIS: 24 INCH TABLE SIZE: 44 INCH X 51 INCH MAXIMUM WORKPIECE WEIGHT: 1,100 LBS MEASURING ACCURACY: 3.33 + 10 M MACHINE DIMENSIONS: 49 INCH X 51 INCH X 108 INCH MACHINE WEIGHT: 2,645 LBS EQUIPPED WITH RENISHAW PH9 AUTO INDEXING PROBE HEAD MITUTOYO CMMC 3S CONTROL AIR DRYER ALL AVAILABLE MANUALS PC, KEYBOARD, MOUSE, AND SOFTWARE IS INCLUDED. RUNNING ON MCOSMOS V 4.1. THE INCLUDED PROBE HEADS ARE 0.3 MM. 2 MM, AND 4 MM.
|
🔒 Subscribe |
|
|
FRAVOL | A16/S |
FRAVOL A16/S CONTOUR EDGEBANDER 38 INCH X 44 INCH TABLE FRONT-MOUNTED SUPPORT ARM WITH ROLLERS 32 INCH DIAMETER EDGE BANDING FEED TABLE OVERHEAD HOLD DOWN AND POWERED ROLLER GLUE POT WITH APPLICATION ROLLER FOOT PEDAL OPERATION TOOL KIT STRAPPED AND WRAPPED ON PALLET
|
🔒 Subscribe | |
|
|
2019 | DELTA SEPARATIONS | FFE-45 |
2019 DELTA SEPARATIONS FFE-45 FALLING FILM EVAPORATOR RECIRCULATING ELECTRIC HEATER HEATING POWER (OPTION 1) 94 AMPS @230V THREE-PHASE (OPTION 2) 47 AMPS @460V THREE-PHASE TRANSFER FLUID FLOW: 25 GPM (25-40 PSI) MAX TEMP: 180F (120C) TRANSFER FLUID LINE CONNECTIONS: 1.5 FNPT DIMENSIONS: 33L X 17W X 52H APPROX. 255 LBS 7 TON WATER CHILLER (OPTION 1) 41 AMPS @230V, THREE-PHASE (OPTION 2) 16 AMPS @460V, THREE-PHASE COOLING POWER: 7 TON EVAPORATING TEMPERATURE: 122F - 180F COOLANT LINE CONNECTIONS:1 FNPT DIMENSIONS: 34 W X 61 L X 49 H SHIPPING WEIGHT: 1200 LBS PUMP CHILLER 21.2 AMPS @230V, SINGLE-PHASE COOLING POWER: 1.5 TON COOLANT FLOW: 3.5 GPM AMBIENT TEMPERATURE: -10F -35F DIMENSIONS: 30.5L X 19W X 26H WEIGHT: 340LBS
|
🔒 Subscribe |
|
|
2005 | HAAS | VF-4SS |
2005 HAAS VF-4SS VERTICAL MACHINING CENTER - 12,000 RPM, AUGER, PROBES X-AXIS 50" Y-AXIS 20" Z-AXIS 25" SPINDLE MOTOR 30 HP SPINDLE SPEED 12,000 RPM TOOL CHANGER ATC-24 SPINDLE TAPER CAT-40 TABLE-W 18" TABLE-L 52" MACHINE DIMENSIONS 152" L X 99" W X 106" H MACHINE WEIGHT 13,500 LBS EQUIPPED WITH: HAAS CNC CONTROL CHIP AUGER MIST COLLECTOR PROBES TOOL/PART ALL AVAILABLE MANUALS
|
🔒 Subscribe |
|
|
2021 | STYLE | STJ1630A |
2021 STYLE STJ1630A CNC LASER CUTTER 60HZ/220V WORKING AREA: 1600X300MM TOTAL POWER 3KW INCLUDES FABRIC FEEDER S/N: ST2021066J
|
🔒 Subscribe |
|
|
2001 | OKUMA | CAPTAIN L370MW |
2001 OKUMA CAPTAIN L370MW CNC LATHE. NON-OPERATIONAL. ERROR MESSAGE WHEN POWERING ON. SWING OVER BED: 20.87 INCH MAXIMUM TURNING DIAMETER: 14.56 INCH MAXIMUM TURNING LENGTH: 19.68 INCH DISTANCE BETWEEN CENTERS: 19.68 INCH BAR CAPACITY: 2.0 INCH X-AXIS TRAVEL: 10.23 INCH Z-AXIS TRAVEL: 20.47 INCH RAPID TRAVERSE X/Z: 787/987 IPM MAIN SPINDLE SPEED: 4,500 RPM MAIN SPINDLE MOTOR: 20 HP MAIN SPINDLE NOSE: A2-6 SUB SPINDLE SPEED: 6,000 RPM SUB SPINDLE MOTOR: 10 HP SUB SPINDLE: 6 INCH CHUCK NUMBER OF TOOL STATIONS: 12 APPROX. WEIGHT: 10,000 LBS APPROX. DIMENSIONS: 107 INCH X 70 INCH X 86 INCH
|
🔒 Subscribe |
|
|
300 |
SPIRAL PRESS & DEWATERING SYSTEM - MODEL-300. SPECIFICATION WEIGHT: 5000 LBS DIMENSION: 13.8 FT X 3 FT X 6.6 FT POWER: 18.5 KW VOLTAGE: 480V AMP: 30 FEED/HOUR: 3 TON OR 8 M3 MESH DENSITY: 0.75 MM MOTOR RPM: 1440 GRADE: STEEL WEIGHT (KG): 2300 DIMENSION (MM): 4142 X 890 X 1946 DIMENSION (M): 4.2 X 0.9 X 2 DIMENSION (INCH): 165.35 X 35.43 X 78.74 DIMENSION (FEET): 13.78 X 2.95 X 6.56 INPUT/HOUR (CUBIC M): 5 INPUT/HOUR (GALLON): 1320 INPUT/HOUR (TON): 3 VOLTAGE: 480V POWER: 18.5KW RPM: 25 DEWATER RATE: 70% MESH DENSITY: 0.75MM MOTOR SPEED: 1440 AMP: 30
|
🔒 Subscribe | ||
|
|
YELLOW MEDIUM SIZE ROLLS (NO TAG)
|
🔒 Subscribe | |||
|
|
1993 | ACCURPRESS | 76010 |
1993 60 TON X 10 ACCURPRESS 76010 CNC HYDRAULIC PRESS BRAKE CAPACITY 60 TONS BED LENGTH 120 DISTANCE BETWEEN HOUSINGS 100 BED HEIGHT 34 RAM OPEN HEIGHT 14 RAM CLOSED HEIGHT 6 RAM STROKE LENGTH 8 THROAT DEPTH 8 MAIN MOTOR 10 HP OVERALL DIMENSIONS, L X H X D 136 X 76 X 42 SHIPPING WEIGHT (APPROX.) 10,000 LBS. ELECTRICS 460 VOLT / 3 PHASE EQUIPPED WITH: ACCURPRESS CNC CONTROL PROGRAMMABLE BACKGAUGE FOOT PEDAL
|
🔒 Subscribe |
|
|
CUSTOM STEEL TABLE 36" SQ X 30" TALL
|
🔒 Subscribe | |||
|
|
CUSTOM STEEL TABLE 48 INCH SQ X 32.5 INCH TALL
|
🔒 Subscribe | |||
|
|
MACHINING TABLE 2' X 40" X 34.5" TALL - 2.75" OVERHANG
|
🔒 Subscribe | |||
|
|
MACHINING TABLE 59.5" X 20" X 37.5" TALL
|
🔒 Subscribe | |||
|
|
CUSTOM STEEL TABLE 36.5 INCH X 38.25 INCH X 33 INCH TALL
|
🔒 Subscribe | |||
|
|
CUSTOM STEEL TABLE 48 INCH X 48.75 INCH X 30.5 INCH TALL
|
🔒 Subscribe | |||
|
|
PLASMA TABLE, 4' X 8'
|
🔒 Subscribe | |||
|
|
2001 | FREIGHTLINER | FL70 |
2001 FREIGHTLINER FL70 TRUCK CAT 3126 DIESEL ENGINE 7.2L AIR RIDE DRIVER SEAT 353,000 MILES EATON FULLER MANUAL TRANSMISSION STAKE BED AERO CONESTOGA COVER WORKING - NEEDS MAINTENANCE NEW PARTS: FUEL TANKS 2023 BATTERIES 8-27-25 BRAKE AIR HOSE 8-27-25 BRAKE AIR VALVE 8-27-25 SPARE PARTS: BLOCK HEATER BRAKE CHAMBER AIR FILTERS 2PCS FUEL FILTERS 4PCS OIL FILTER S/N: 1FVABTAK61HJ21459
|
🔒 Subscribe |
|
|
WELLS MFG. CORP. | 837 |
WELLS MFG. CORP. VERTICAL KNEE MILL MODEL 837 S/N 1618
|
🔒 Subscribe | |
|
|
NIAGARA | HD500-10-14 |
500 TON X 10.5' NIAGARA HD500-10-14 HYDRAULIC PRESS BRAKE CAPACITY: 500 TONS OVERALL LENGTH: 10.5 STROKE: 12 CLOSED HEIGHT: 10 OPEN HEIGHT: 22 DISTANCE BELOW FLOOR: 34 MACHINE DIMENSIONS: 14.5 L, 8.5 W, 11.5 H MACHINE WEIGHT: 81,300LBS
|
🔒 Subscribe | |
|
|
2019 | DELTA SEPARATIONS | RFD-27 |
2019 DELTA SEPARATIONS RFD-27 ROLLED FILM SHORT PATH DISTILLATION SURFACE AREA: 0.27M2 SYSTEM FEED RATE: 4-5 LITERS PER HOUR JACKETED FEED TANK: 5 LITERS COLLECTION TANKS: 7.5 LITERS DIMENSION 67L X 24W X 77.54H WEIGHT 600 LBS ELECTRICAL REQUIREMENTS 110V & 230V SINGLE-PHASE, FUL-LOAD-AMPERAGE (FLA): 60 VACUUM SYSTEM TURBO PUMP: 240 LITERS PER SECOND ROUGHING SCROLL PUMP: 12.7 M2 PER HOUR ROLLER CONTROLLER 100-240V, 1 AMP, SINGLE-PHASE 1X NEMA 5-15 PLUG FEED PUMP 110V, 5 AMPS,SINGLE-PHASE, 50/60 HZ 1X NEMA 5-15 PLUG
|
🔒 Subscribe |
|
|
2020 | SHANGHAI HUACHENG | 180N |
2020 SHANGHAI HUACHENG 180N FORM FILL AND SEAL MACHINE. PACKING PARAMETERS: MIN.BAG: (WXH): 2.95" X 3.34" - MAX.BAG: (WXH): 3.54" X 8.85" - MAX.VOLUME: 400ML - SPEED (PPM ): 80 & 100 - FILM THICKNESS: 60-140U - MAX.DIAMETER OF REEL: 19.68" - INNER DIAMETER OF REEL: 2.75"- 3.14". EQUIPMENT SPECIFICATION: DIMENSION: 157.48" X 38.58" X 57.08" - TOTAL WEIGHT: 3,968 LBS. WORKING CONDITION: WORKING TEMPERATURE: -10C+55C - RELATIVE HUMIDITY (FROSTLESS CONDITION) :85% - POWER: (480 60HZ) - WORKING PRESSURE: 0.6MPA - AIR CONSUMPTION: 300L/MIN - POWER: 7KW.
|
🔒 Subscribe |
|
|
GALLMEYER & LIVINGSTON | NO. 35 |
GALLMEYER & LIVINGSTON NO. 35 SURFACE GRINDER
|
🔒 Subscribe | |
|
|
WISCONSIN OVEN |
650 WISCONSIN OVEN- 110"H X 66"W X 52"D OUTSIDE DIMENSIONS
|
🔒 Subscribe | ||
|
|
GRIEVE |
GRIEVE OVEN CAN GET UP TO 650 DEGREES
|
🔒 Subscribe | ||
|
|
PISTON FILLERS
|
🔒 Subscribe | |||
|
|
2008 | HOMAG | KAL310 |
2008 HOMAG KAL310 EDGEBANDER. WORKING LEVEL 950 MM (37-13/32). MIN. WORKING WIDTH W/THICKNESS 22 MM (7/8) 55 MM (2-5/32) 60 MM (2-3/8) 100 MM (3-5/16). PANEL OVERHANG 30 MM (1-1/8"). WORKPIECE THICKNESS MIN. 12 MM (15/32") MAX. 60 MM (2-3/8"). EDGE THICKNESS STRIPS 0.4 MM TO 20 MM (0.16" TO 25/32") COILS 0.3 MM TO 3 MM (0.12" TO 1/8"). PROCESSING LIMITS STRIPS 900 MM2 (1.39 SQ. IN) COILS 135 MM2 (0.19 SQ. IN). MACHINE PAINT COLOR GRAY RDS 240 80 05. VARIABLE FEED SPEED 18 M/MIN TO 25 M/MIN (59 FT/MIN TO 82 FT/MIN). RETURN CONVEYORS NOT INCLUDED.
|
🔒 Subscribe |
|
|
2021 | P/A INDUSTRIES | SRWD-2-LC2 |
2021 P/A INDUSTRIES SRWD-2-LC2 REWIND REEL - POWERED COIL REWINDER FOR STAMPING & PRESS LINES. REEL CAPACITY APPROX. 2,000 LB (VARIES BY CONFIGURATION). COIL WIDTH CAPACITY UP TO 20 IN. (TYPICAL). COIL OD CAPACITY UP TO 48 IN. (TYPICAL). FEED DIRECTION LEFT-TO-RIGHT. DRIVE SYSTEM AC MOTOR WITH VARIABLE SPEED CONTROL. TENSION CONTROL ADJUSTABLE / AUTOMATIC FEEDBACK SYSTEM. CONTROL PANEL INTEGRATED OPERATOR STATION WITH SPEED & DIRECTION CONTROL. ELECTRICAL 230/460V, 3-PHASE.
|
🔒 Subscribe |
|
|
2017 | SW BA | W02-22 |
2017 SW BA W02-22 HORIZONTAL MACHINING CENTER, HMC X-AXIS: 7.87 Y-AXIS: 13.78 (20.67 WITH TOOLCHANGE POSITION) Z-AXIS: 11.81 SPINDLE DISTANCE: 9.84 SPINDLE TAPER: HSK-A40 SPINDLE SPEED: 25,000 RPM SWIVEL CARRIER / COUNTERBEARING: EQUIPPED WITH CROWN GEAR, SWIVEL TIME 0/180 APPROX. 2.25 S A- AND U-AXIS: PREPARED FOR MOUNTING A FIXTURE PLATE, UP TO MAX 16.73 X 24.80 DRIVE SYSTEM: TORQUE MOTOR LOAD CAPACITY: 2 X 352.74 LBS SPEED RANGE: A- AND U-AXIS: 1 100 RPM C- AND W-AXIS: 2 SATELLITES TOOLCHANGE: CHIP-TO-CHIP TIME: APPROX. 1.75 S WEIGHT / DIMENSIONS: TOTAL WEIGHT: APPROX. 13,889 LBS TRANSPORT DIMENSIONS (W X H X L): 75.59 X 92.52 X 100.39 MACHINE INSTALLED (W X H X L): 125.98 X 114.17 X 204.72 CONNECTED LOAD: OPERATING VOLTAGE: 3 X 400 VOLT, 50 HZ, TN-S/TN-C NETWORK TOTAL CONNECTED LOAD: 41 KVA MEAN AIR CONSUMPTION: 14.12 CUBIC FEET PER MINUTE (80 PSI) CONTROL: SIEMENS SINUMERIK 840D SL
|
🔒 Subscribe |
|
|
2021 | EPSON | RVT6L-A901SS |
2021 (6) EPSON RVT6L-A901SS 6 AXIS INDUSTRIAL ROBOTS - 6 KG CAPACITY, 900 MM REACH. MODEL RVT6L-A901SS TYPE 6-AXIS ARTICULATED ROBOT PAYLOAD CAPACITY 6 KG (13.2 LB) MAX REACH 900 MM (35.4 IN) REPEATABILITY 0.02 MM MOUNTING FLOOR / CEILING / WALL CONTROLLER EPSON RC700-A (OR RC90, VERIFY INCLUDED CONTROLLER) WEIGHT ~37 KG (81 LB) POWER SUPPLY 200-240 VAC, SINGLE PHASE I/O 24 INPUTS / 16 OUTPUTS, ETHERNET/IP & DEVICENET CAPABLE CYCLE TIME ~0.37 SEC (RATED)
|
🔒 Subscribe |
|
|
FANUC | R30IB PLUS |
4AXIS STAINLESS STEEL DELTA ROBOT, FOODGRADE, IP69K WASHDOWN. PAYLOAD: 6 KG AT WRIST. REACH / WORKING RANGE: 1200 MM HORIZONTAL, 450 MM VERTICAL. REPEATABILITY: 0.03 MM. ROBOT WEIGHT: 250 KG (551 LB). AXES: 4AXIS DESIGN (3 ARMS + ROTARY AXIS J4). J4 MOTION RANGE: 720, MAX SPEED 1714/S. PROTECTION RATING: BODY, ARMS, AND WRIST RATED IP69K, SUITABLE FOR HIGHPRESSURE, HIGHTEMPERATURE WASHDOWN AND MEETING USDA/FDA FOODHANDLING STANDARDS. CONTROLLER: FANUC R30IB PLUS, COMPATIBLE WITH OPTIONS LIKE IRVISION, FORCE SENSING, ROBOT LINK, COLLISION GUARD, AND ZDT
|
🔒 Subscribe | |
|
|
2021 | COGNEX | 3D-L4000 IN-SIGHT |
2021 COGNEX 3D-L4000 IN-SIGHT 3D LASER VISION SYSTEM HIGH PRECISION INDUSTRIAL INSPECTION LASER WAVELENGTH: 450 NM BLUE LASER BYTRONIC VISION INTELLIGENCE LASER CLASS: 2M OUTPUT POWER ~45 MW MEASUREMENT RANGES FOR DIFFERENT MODELS: CLEARANCE DISTANCE ~92 MM / 130 MM / 180 MM; Z-AXIS MEASUREMENT RANGES ~106 MM / 235 MM / 745 MM FIELD OF VIEW (X-AXIS) NEAR/MIDDLE/FAR FOR RESPECTIVE MODELS E.G., 55/72.5/90 MM (FOR FIRST VARIANT) RESOLUTION & REPEATABILITY: Z RESOLUTION TOP ~2.5 M, REPEATABILITY DOWN TO ~0.5 M (FOR TOP VARIANT) SCAN RATE: UP TO 4 KHZ (OR UP TO ~6 KHZ WHEN WINDOWING SENSOR) DIMENSIONS: 150.5 MM 101 MM 45 MM; WEIGHT ~0.94 KG HOUSING: IP65 (WITH PROPER CABLE ATTACHMENTS) OPERATING TEMPERATURE: 0-45 C (32-113 F) TYPICAL, STORAGE -20-70 C POWER SUPPLY: 24 VDC 10%, MINIMUM ~750 MA
|
🔒 Subscribe |
|
|
CUSTOM STEEL TABLE 48.5 INCH SQ X 31.5 INCH TALL
|
🔒 Subscribe | |||
|
|
CUSTOM STEEL TABLE 48.5 INCH SQ X 35.25 INCH TALL
|
🔒 Subscribe | |||
|
|
CUSTOM STEEL TABLE 48.5 INCH SQ X 31.5 INCH TALL
|
🔒 Subscribe | |||
|
|
WD-2430E |
PARTS WASHER WD-2430E, S/N 11206
|
🔒 Subscribe | ||
|
|
F C250C |
HEAVY DUTY STAPLER F C250C, S/N 9K046
|
🔒 Subscribe | ||
|
|
SP3X1.5SB-90-KTL |
CIP SPRAY BALL, WITH 3IN. TC PORT X 1.5IN. TC PORT @ 90 DEGREES. NON-ROTATING TYPE. SPRAYS FROM BOTTOM HALF OF THE BALL ONLY IDEAL FOR KETTLES WITH FLIP TOP LIDS TO MINIMIZE SPRAY COMING OUT THE TOP.
|
🔒 Subscribe | ||
|
|
SP2-4BBL-CON |
CONDENSATE STACK FOR 2 TO 4 BBL BREW KETTLES. ADDS 18-INCH TO KETTLE HEIGHT. EXTENDS 32-INCH (END TO END). CONNECT YOUR 6-INCH STEAM VENT TO THE TOP OF THE TEE ON THIS CONDENSATE STACK. OUTSIDE DIAMETER OF KETTLE TC FLANGE IS 6-9/16". OLDER KETTLES MAY HAVE DIFFERENT FLANGE SIZE.
|
🔒 Subscribe | ||
|
|
BK90TW-TI-SG-EL3-LS1 |
90 GAL BREW KETTLE WITH THERMOWELL, SIGHT GLASS, TANGENTIAL INLET, (3) TC PORTS FOR ELECTRIC HEATING ELEMENTS, (3) 1.5-IN. TC X 1-IN. NSP ADAPTERS, (1) TC PORT FOR LEVEL SENSORS, (1) TC PORT WITH THERMOWELL, (1) 1.5-IN. TC X 1/2-IN. NPT-FEMALE ADAPTER, (3) 1.5-IN. BUTTERFLY VALVES. BREW KETTLE HAS DISH BOTTOM FOR BETTER REMOVAL OF TRUB AND HOPS. 25.5-IN. DIAMETER X 53-IN.H.
|
🔒 Subscribe | ||
|
|
CUSTOM STEEL |
CUSTOM STEEL HYDRAULIC TABLE 54 INCH SQ X 35.75 INCH TALL
|
🔒 Subscribe | ||
|
|
1999 | CMS | PG5 |
1999 CMS PG5 VERTICAL CNC CENTER 5 AXIS CNC ~ 120" IN X/240" IN Y/24" IN Z - PG5, S/N B391 W/ OSAI CMS CONTROLLER - PXS 4204. CONTROLLER S/N 984403. TRAVEL 120 INCHES = X & Y, 24 INCHES = Z. FEED RATE 120 INCHES PER MINUTE IN X&Y, 24 INCHES PER MINUTE IN Z. TOOL CHANGE SPEED - 3.5 MINUTES. TAPER - ISO40. SPINDLE SPEED - 24000 RPM. RAPIDS - 41 INCHES PER MINUTE. COOLING CAP - 1020 W. VOLTAGE - 230 V 50-60 HZ. INPUT - 555 W. NOMINAL CURRENT FLA - 2.8 A. REFRIGERANT - R 134A 320 G. AMBIENT TEMP - 55. CABINET TEMP - 50. PROTECTION - IP 54 IP 34. NOISE LEVEL - 62 DB. WEIGHT - 41 KG. DIN 3168 - L35 50 HZ.
|
🔒 Subscribe |
2004 MILLTRONICS VM-22
CNC MACHINE CENTERS
2004 MILLTRONICS VM-22 VERTICAL MACHINING CENTER X-AXIS TRAVEL: 40 INCH Y-AXIS TRAVEL: 22 INCH Z-AXI...
Hammer Price:
🔒
EDWARDS
METALWORKING & FABRICATION EQUIPMENT
EDWARDS IRON WORKER, 25 TON S/N: 1049141W25...
Hammer Price:
🔒
2017 OKUMA 2SP-250H
METALWORKING & FABRICATION EQUIPMENT
2017 OKUMA 2SP-250H TWIN SPINDLE TWIN TURRET CNC LATHE - TWIN SPINDLE TWIN TURRET CNC TURNING CENTER...
Hammer Price:
🔒
CROWN 15BT
MATERIAL HANDLING & WAREHOUSE EQUIPMENT
CROWN PALLET JACK, MODEL 15BT, S/N: 1A194571...
Hammer Price:
🔒
ROL-LIFT
MATERIAL HANDLING & WAREHOUSE EQUIPMENT
ROL-LIFT PALLET JACK, 1000 LBS, S/N: CB4598...
Hammer Price:
🔒
SPEED-CUT 21C.100.03387
METALWORKING & FABRICATION EQUIPMENT
SPEED-CUT ABRASIVE CUTOFF MACHINE, S/N: 21C.100.03387...
Hammer Price:
🔒
JMT PBM 50
METALWORKING & FABRICATION EQUIPMENT
JMT PBM 50 ANGLE, FLAT BAR AND ROUND STOCK BENDER S/N: N7119...
Hammer Price:
🔒
MARVEL SERIES 8 MARK II
METALWORKING & FABRICATION EQUIPMENT
MARVEL SERIES 8 MARK II PIPE SAW...
Hammer Price:
🔒
2001 MITUTOYO BHN706
TEST, MEASUREMENT & QUALITY EQUIPMENT
2001 MITUTOYO BHN706 CNC COORDINATE MEASURING MACHINE X AXIS: 28 INCH Y AXIS: 24 INCH Z AXIS: 24 INC...
Hammer Price:
🔒
FRAVOL A16/S
METALWORKING & FABRICATION EQUIPMENT
FRAVOL A16/S CONTOUR EDGEBANDER 38 INCH X 44 INCH TABLE FRONT-MOUNTED SUPPORT ARM WITH ROLLERS 32 IN...
Hammer Price:
🔒
2019 DELTA SEPARATIONS FFE-45
CHEMICAL PROCESSING EQUIPMENT
2019 DELTA SEPARATIONS FFE-45 FALLING FILM EVAPORATOR RECIRCULATING ELECTRIC HEATER HEATING POWER (O...
Hammer Price:
🔒
2005 HAAS VF-4SS
CNC MACHINE CENTERS
2005 HAAS VF-4SS VERTICAL MACHINING CENTER - 12,000 RPM, AUGER, PROBES X-AXIS 50" Y-AXIS 20" Z-AXIS ...
Hammer Price:
🔒
2021 STYLE STJ1630A
LASER ETCHING & ENGRAVING EQUIPMENT
2021 STYLE STJ1630A CNC LASER CUTTER 60HZ/220V WORKING AREA: 1600X300MM TOTAL POWER 3KW INCLUDES FAB...
Hammer Price:
🔒
2001 OKUMA CAPTAIN L370MW
CNC MACHINE CENTERS
2001 OKUMA CAPTAIN L370MW CNC LATHE. NON-OPERATIONAL. ERROR MESSAGE WHEN POWERING ON. SWING OVER BED...
Hammer Price:
🔒
300
MISC
SPIRAL PRESS & DEWATERING SYSTEM - MODEL-300. SPECIFICATION WEIGHT: 5000 LBS DIMENSION: 13.8 FT X 3 ...
Hammer Price:
🔒
1993 ACCURPRESS 76010
METALWORKING & FABRICATION EQUIPMENT
1993 60 TON X 10 ACCURPRESS 76010 CNC HYDRAULIC PRESS BRAKE CAPACITY 60 TONS BED LENGTH 120 DISTANCE...
Hammer Price:
🔒
MATERIAL HANDLING & WAREHOUSE EQUIPMENT
CUSTOM STEEL TABLE 48 INCH SQ X 32.5 INCH TALL...
Hammer Price:
🔒
MATERIAL HANDLING & WAREHOUSE EQUIPMENT
MACHINING TABLE 2' X 40" X 34.5" TALL - 2.75" OVERHANG...
Hammer Price:
🔒
MATERIAL HANDLING & WAREHOUSE EQUIPMENT
CUSTOM STEEL TABLE 36.5 INCH X 38.25 INCH X 33 INCH TALL...
Hammer Price:
🔒
MATERIAL HANDLING & WAREHOUSE EQUIPMENT
CUSTOM STEEL TABLE 48 INCH X 48.75 INCH X 30.5 INCH TALL...
Hammer Price:
🔒
2001 FREIGHTLINER FL70
TRUCKS, TRAILERS & VEHICLES
2001 FREIGHTLINER FL70 TRUCK CAT 3126 DIESEL ENGINE 7.2L AIR RIDE DRIVER SEAT 353,000 MILES EATON FU...
Hammer Price:
🔒
WELLS MFG. CORP. 837
METALWORKING & FABRICATION EQUIPMENT
WELLS MFG. CORP. VERTICAL KNEE MILL MODEL 837 S/N 1618...
Hammer Price:
🔒
NIAGARA HD500-10-14
PRESSES & FORMING
500 TON X 10.5' NIAGARA HD500-10-14 HYDRAULIC PRESS BRAKE CAPACITY: 500 TONS OVERALL LENGTH: 10.5 ST...
Hammer Price:
🔒
2019 DELTA SEPARATIONS RFD-27
CHEMICAL PROCESSING EQUIPMENT
2019 DELTA SEPARATIONS RFD-27 ROLLED FILM SHORT PATH DISTILLATION SURFACE AREA: 0.27M2 SYSTEM FEED R...
Hammer Price:
🔒
2020 SHANGHAI HUACHENG 180N
PACKAGING EQUIPMENT
2020 SHANGHAI HUACHENG 180N FORM FILL AND SEAL MACHINE. PACKING PARAMETERS: MIN.BAG: (WXH): 2.95" X ...
Hammer Price:
🔒
GALLMEYER & LIVINGSTON NO. 35
SURFACE FINISHING EQUIPMENT
GALLMEYER & LIVINGSTON NO. 35 SURFACE GRINDER...
Hammer Price:
🔒
2008 HOMAG KAL310
COMMERCIAL PRINTING & BINDERY EQUIPMENT
2008 HOMAG KAL310 EDGEBANDER. WORKING LEVEL 950 MM (37-13/32). MIN. WORKING WIDTH W/THICKNESS 22 MM ...
Hammer Price:
🔒
2021 P/A INDUSTRIES SRWD-2-LC2
PRESSES & FORMING
2021 P/A INDUSTRIES SRWD-2-LC2 REWIND REEL - POWERED COIL REWINDER FOR STAMPING & PRESS LINES. REEL ...
Hammer Price:
🔒
2017 SW BA W02-22
CNC MACHINE CENTERS
2017 SW BA W02-22 HORIZONTAL MACHINING CENTER, HMC X-AXIS: 7.87 Y-AXIS: 13.78 (20.67 WITH TOOLCHANGE...
Hammer Price:
🔒
2021 EPSON RVT6L-A901SS
INDUSTRIAL AUTOMATION, CONTROLS & ROBOTICS
2021 (6) EPSON RVT6L-A901SS 6 AXIS INDUSTRIAL ROBOTS - 6 KG CAPACITY, 900 MM REACH. MODEL RVT6L-A901...
Hammer Price:
🔒
FANUC R30IB PLUS
FOOD PROCESSING AND RESTAURANT EQUIPMENT
4AXIS STAINLESS STEEL DELTA ROBOT, FOODGRADE, IP69K WASHDOWN. PAYLOAD: 6 KG AT WRIST. REACH / WORKIN...
Hammer Price:
🔒
2021 COGNEX 3D-L4000 IN-SIGHT
TEST, MEASUREMENT & QUALITY EQUIPMENT
2021 COGNEX 3D-L4000 IN-SIGHT 3D LASER VISION SYSTEM HIGH PRECISION INDUSTRIAL INSPECTION LASER WAVE...
Hammer Price:
🔒
MATERIAL HANDLING & WAREHOUSE EQUIPMENT
CUSTOM STEEL TABLE 48.5 INCH SQ X 31.5 INCH TALL...
Hammer Price:
🔒
MATERIAL HANDLING & WAREHOUSE EQUIPMENT
CUSTOM STEEL TABLE 48.5 INCH SQ X 35.25 INCH TALL...
Hammer Price:
🔒
MATERIAL HANDLING & WAREHOUSE EQUIPMENT
CUSTOM STEEL TABLE 48.5 INCH SQ X 31.5 INCH TALL...
Hammer Price:
🔒
SP3X1.5SB-90-KTL
CHEMICAL PROCESSING EQUIPMENT
CIP SPRAY BALL, WITH 3IN. TC PORT X 1.5IN. TC PORT @ 90 DEGREES. NON-ROTATING TYPE. SPRAYS FROM BOTT...
Hammer Price:
🔒
SP2-4BBL-CON
WINERY AND BREWERY EQUIPMENT
CONDENSATE STACK FOR 2 TO 4 BBL BREW KETTLES. ADDS 18-INCH TO KETTLE HEIGHT. EXTENDS 32-INCH (END TO...
Hammer Price:
🔒
BK90TW-TI-SG-EL3-LS1
FOOD PROCESSING AND RESTAURANT EQUIPMENT
90 GAL BREW KETTLE WITH THERMOWELL, SIGHT GLASS, TANGENTIAL INLET, (3) TC PORTS FOR ELECTRIC HEATING...
Hammer Price:
🔒
CUSTOM STEEL
MATERIAL HANDLING & WAREHOUSE EQUIPMENT
CUSTOM STEEL HYDRAULIC TABLE 54 INCH SQ X 35.75 INCH TALL...
Hammer Price:
🔒
1999 CMS PG5
CNC MACHINE CENTERS
1999 CMS PG5 VERTICAL CNC CENTER 5 AXIS CNC ~ 120" IN X/240" IN Y/24" IN Z - PG5, S/N B391 W/ OSAI C...
Hammer Price:
🔒