Surplus CNC Fabrication Industrial Equipment Multiple Locations

2023 USNR UNSCRAMBLER BYPASS WITH CHAINS, NEW, NEVER USED. DRIVE CALCULATIONS: DROP OUT GATE DRIVEN FROM BY-PASS TABLE DRIVEN FROM RPM 62.1 RPM DRIVEN FROM SPROCKET 21 TEETH HEAD SHAFT DRIVE SPROCKET 28 TEETH HEAD SHAFT RPM 46.6 RPM HEAD SHAFT SPROCKET 35 TEETH RC80 CHAIN SPEED 136 FPM

2023 USNR UNSCRAMBLER BYPASS TIPPLE, NEW, NEVER USED. DRIVE CALCULATIONS: MACHINE DESCRIPTION: BYPASS TIPPLE CHAINS LIFT MOTOR RPM @ 60 HZ 1750 RPM OPERATING FREQUENCY 80 HZ REDUCER INPUT RPM 2333.3 RPM REDUCER RATIO 104 REDUCER OUTPUT RPM 22.4 RPM REDUCER OUTPUT SPROCKET 21 TEETH 120-2 DUPLEX DRIVESHAFT DRIVEN SPROCKET 60 TEETH 120-2 DUPLEX DRUM RPM 7.84 RPM WIND-UP DRUM DIAMETER 19.2 INCHES HOIST SPEED 15.8 IN/S MACHINE DESCRIPTION: BYPASS TIPPLE LIFT ENCODER DIRECT COUPLED TO UPPER TIPPLE LIFT DRIVESHAFT ENCODER SHAFT RPM 7.84 RPM HOIST RATE 120.918 IN/REV MACHINE DESCRIPTION: BYPASS TIPPLE CHAINS DRIVE FROM: PLANER OUTFEED LANDING TABLE HEAD SHAFT RPM 43.4 RPM HEAD SHAFT SPROCKET 51 TEETH RC60 LUG SPACING 28 PITCHES = 14 C2060H PITCHES = 21 INCHES LUG RATE 79.0 LPM CHAIN SPEED 138.25 FPM S/N: 10551-0003

2023 USNR PLANER OUTFEED LANDING TABLE WITH ANGLED ROLLS, NEW, NEVER USED. SPECIFICATIONS: DRIVE CALCULATION: MACHINE DESCRIPTION: PLANER OUTFEED LANDING TABLE ROLLS OPERATING FREQUENCY: 75 HZ REDUCER INPUT RPM: 2188 RPM REDUCER RATIO: 21.87 REDUCER OUTPUT RPM: 100 RPM ROLL DRIVE SPROCKET: 25 TEETH ROLL SHAFT DRIVEN SPROCKET: 18 TEETH ROLL SHAFT RPM: 138.9 RPM ROLL SPIRAL PITCH: 12 IN SPIRAL SPEED PARALLEL TO FLOW: 134.2 FPM DRIVE CALCULATIONS: MACHINE DESCRIPTION: PLANER OUTFEED LANDING TABLE FENCE OPERATING FREQUENCY: 75 HZ REDUCER INPUT RPM: 2188 RPM REDUCER RATIO: 34.81 REDUCER OUTPUT RPM: 62.8 RPM HEAD PULLEY DIAMETER: 8 IN BELT SPEED: 131.6 FPM DRIVE CALCULATION: MACHINE DESCRIPTION: PLANER OUTFEED LANDING TABLE OPERATING FREQUENCY: 75 HZ REDUCER INPUT RPM: 2188 RPM REDUCER RATIO: 35.25 REDUCER OUTPUT RPM: 62.1 RPM HEAD SHAFT DRIVE SPROCKET: 21 TEETH HEADSHAFT RPM: 43.4 RPM HEADSHAFT SPROCKET: 14 TEETH CHAIN SPEED: 132.2 FPM S/N: 10551-0002

2023 USNR BYPASS TABLE, NEW, NEVER USED. DRIVE CALCULATIONS: MOTOR RPM @ 60HZ 1750 RPM OPERATING FREQUENCY 75 HZ GEARMOTOR INPUT RPM 2188 RPM GEARMOTOR RATIO 35.25 GEAR MOTOR OUTPUT RPM 62.1 RPM GEAR MOTOR OUTPUT SPROCKET 21 TEETH HEAD SHAFT DRIVEN SPROCKET 28 TEETH HEAD SHAFT RPM 46.6 RPM CHAIN PITCH 2.609 IN. HEADSHAFT SPROCKET 13 TEETH CHAIN SPEED 131.7 FPM S/N: 10551-0004

2023 USNR DUAL ARTICULATING SMART GATE, NEW, NEVER USED. DRIVE CALCULATIONS: MACHINE DESCRIPTION: LUGGED TRANSFER ENCODER DRIVEN FROM LUGGED TRANSFER DRIVEN FROM RPM 93.3 RPM DRIVEN FROM SPROCKET 36 TEETH ENCODER DRIVEN SPROCKET 24 TEETH ENCODER SHAFT RPM 140.0 RPM ENCODER RATE 1.0 REV/LUG. MACHINE DESCRIPTION: DUAL ACTING SMART GATE DRIVEN FROM LUGGED TRANSFER DRIVEN FROM RPM 93.3 RPM DRIVEN FROM SPROCKET 22 TEETH HEAD SHAFT DRIVEN SPROCKET 21 TEETH HEAD SHAFT RPM 97.8 RPM HEAD SHAFT SPROCKET 38 TEETH CHAIN SPEED 309.6 FPM S/N: 10552-0008

2023 USNR PLANER BACKLOG TABLE #3, NEW, NEVER USED. DRIVE CALCULATION: MACHINE DESCRIPTION PLANER BACKLOG TABLE #3 OPERATING FREQUENCY 60 HZ REDUCER INPUT RPM 1750 RPM REDUCER RATIO 35.25 REDUCER OUTPUT RPM 49.6 RPM REDUCER OUTPUT SPROCKET 24 TEETH HEAD SHAFT DRIVEN SPROCKET 24 TEETH HEAD SHAFT RPM 49.6 RPM HEAD SHAFT SPROCKET 14 TEETH CHAIN SPEED 151.11 FPM S/N: 10552-0009

2023 USNR ENDING ROLL TRANSFER, NEW, NEVER USED. DRIVE CALCULATIONS: MACHINE DESCRIPTION: ENDING ROLL TRANSFER DRIVEN FROM TRAY SORTER JACKSHAFT DRIVEN FROM RPM 93.33 RPM DRIVEN FROM SPROCKET 30 TEETH HEAD SHAFT DRIVE SPROCKET 28 TEETH HEAD SHAFT RPM 100.0 RPM HEADSHAFT SPROCKET 14 TEETH LUG SPACING 10 PITCHES LUG SPEED 140 LPM LUG RATE 304.4 FPM. DRIVE CALCULATIONS: MACHINE DESCRIPTION: ENDING ROLLS MOTOR RPM @ 60 HZ 1750 RPM OPERATING FREQUENCY 67 HZ REDUCER INPUT RPM 1954 RPM REDUCER RATIO 21.87 :1 REDUCER OUTPUT RPM 89.3 RPM REDUCER SPROCKET 21 TEETH HEAD PULLEY SPROCKET 15 TEETH HEAD PULLEY RPM 125.0 RPM ROLLS DIAMETER 10.75 INCH DIA. BELT SPEED 352 FPM. S/N: 10553-0117

2023 USNR OVERHEAD PUSHER DROP OUT, NEW, NEVER USED. SPECIFICATIONS: MOTOR RPM @ 60 HZ 1780 RPM REDUCER RATIO 78 HZ / 2270 RPM OUTPUT RPM 858.3 RPM ENCODER RATE 1.0000 REV/LUG. FAN MOTOR RPM @ 60 HZ 1750 RPM DRIVEN FROM OVERHEAD PUSHER DROP OUT DRIVEN FROM RPM 858.3 RPM ENCODER RATE 16.2174 REV/LUG. ENCODER SHAFT RPM 2270.4 RPM ENCODER RATE 16.2174 REV/LUG. DRIVEN FROM OVERHEAD PUSHER DROP OUT DRIVEN FROM RPM 858.3 RPM DRIVEN FROM SPROCKET 20 T ENCODER SHAFT RPM 140.0 RPM ENCODER RATE 1.0000 REV/LUG. S/N: 10553-0116

1700 GPM 155 FT.W.C. SIC VERTICAL SPLIT CASE PUMP, NEW, NEVER USED WITH ABB DRIVES

800 TON YORK CENTRIFUGAL CHILLERS MODEL #YKL7LGH9-UEHS, NEW, NEVER USED UNDER LOAD. UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. 800-TON CENTRIFUGAL COMPRESSOR WITH FACTORY INSTALLED VFD R-134A REFRIGERANT ALL CHILLED WATER AND CONDENSER WATER CONNECTIONS ARE VICTAULIC CONNECTIONS VARIABLE PRIMARY FLOW CONTROLS HOT GAS BYPASS FACTORY INSTALLED FLOW SWITCHES BACNET CONTROL INTERFACE UL LISTED, 460VAC/60HZ EVAP. COND. REFRIG. DWP, PSIG: 235 235 LIQUID DWP, PSIG: 150 150 NO. OF PASSES: 2 2 TUBE DESCRIPTION: 656 471 CONDENSER GAS INLET: BAFFLE REFRIGERANT: R-134A CHARGE, LBS: 2254 VOLTS-PHASE-HZ FLA OIL PUMP 2 HP 460-3-60 3.6 OIL HEATER N/A 460-3-60 3.0 S/N: SEGM-361950

1700 GPM 155 FT.W.C. SIC VERTICAL SPLIT CASE PUMP, NEW, NEVER USED WITH ABB DRIVES

2023 USNR CUT IN TWO CLAMP, NEW, NEVER USED. INCLUDES FRAME WELDMENT, WIND-UP SHAFT, AIR SCHEMATIC, HOLD DOWN SHOE ASSEMBLY, WIND-UP HANDLE, THICKNESS POINTER BACKING PLATE, PIVOT PINS, SAFETY DECAL, NYLON STRAPPING, PIPE BLOCK, BEARING CAP, COTTER PINS, HARD WASHERS, HEX NUTS, HEX JAM NUTS, HEX HEAD CAP SCREWS, AND LOCKWASHERS. ALL SPECIFICATIONS MUST BE CONFIRMED BY THE PURCHASING ENTITY.

2023 USNR TRIMMER OUTFEED HOLD DOWNS, NEW, NEVER USED. HOLD DOWN MOUNTING FRAME ASSEMBLY, TRIMMER OUTFEED HOLD DOWN SHOE ASSEMBLY, ELECTRICAL COMPONENTS, SAFETY DECALS, JUNCTION BOX AND CABLES, WIND-UP HANDLE, WIND-UP SHAFT, OUTFEED HOLD DOWNS, PIVOT PIN THRU 1 INCH OD X 3.75 INCH LG, PIVOT PIN THREADED 1 INCH OD X 3.75 INCH LG, STRAPPING NYLON 1 PLY X 2 WIDE, THICKNESS POINTER BACKING PLATE, BLOCK 2 PIPE UHMW, BEARING CAP, COTTER PIN, HARD WASHER, HEX NUT-STD-GR 8, HEX JAM NUT, HEX HEAD CAP SCREW, STD LOCKWASHER, HEX HEAD CAP SCREW, GRADE 8, STD LOCKWASHER, HARD WASHER SAE GRADE 8. S/N: 10553-0115

2023 USNR POSITIONING TRANSFER, NEW, NEVER USED. MACHINE DESCRIPTION POSITIONING TRANSFER DRIVEN FROM TRIMMER TRANSFER DRIVEN FROM RPM 70 RPM DRIVEN FROM SPROCKET 24 TEETH HEAD SHAFT DRIVEN SPROCKET 21 TEETH HEAD SHAFT RPM 80 RPM HEAD SHAFT SPROCKET 14 TEETH LUG SPACING 8 PITCHES LUG RATE 140.0 LPM. ROLL & ROLL DRIVE SPECIFICATIONS OPERATING FREQUENCY 65 HZ REDUCER INPUT RPM 1896 RPM REDUCER RATIO 21.87 REDUCER OUTPUT RPM 86.7 RPM REDUCER OUTPUT SPROCKET 15 TEETH ROLL SHAFT DRIVEN SPROCKET 15 TEETH ROLL SHAFT RPM 86.7 RPM ROLL DIAMETER 8.625 INCH ROLL SPEED 195.7 FPM. S/N: 10553-0110

MARLEY 800-TON COOLING TOWER CELL WITH DRIVES, EQUALIZATION PIPING, SS BASINS, ACCESS WALKWAYS. NEVER USED UNDER LOAD. UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. SPECIFICATIONS: MANUFACTURER: MARLEY MODEL NUMBER: NC NUMBER OF SEPARATELY OPERABLE CELLS PER TOWER: 3 COMMON SUMP FOR MULTI-CELL TOWER(S)? (YES/NO): 2 SEPARATE CELLS WITH EQUALIZER PIPING MATERIALS OF CONSTRUCTION (TOWER BASIN, STRAINER): STAINLESS STEEL HOT WATER AND COLD WATER BASINS MATERIALS OF CONSTRUCTION (TOWER CASING): GALVANIZED STEEL MATERIALS OF CONSTRUCTION (FAN BLADES): ALUMINUM DRIVE TYPE: GEAR BASIN SWEEP ACCESSORY (YES/NO): YES, FACTORY INSTALLED WATER TREATMENT ACCESSORY (DESCRIBE): BASIN SWEEP SAFETY GUARDRAILS: YES, PERIMETER GUARDRAIL SYSTEM ON ENTIRE FAN DECK ACCESS LADDER ACCESSORY (INSIDE/OUTSIDE/NONE): YES, ACCESS LADDER TO TOP OF EACH FAN DECK INTERNAL ACCESS LADDER ACCESSORY: YES, ACCESS LADDER WITH SERVICE PLATFORM INSIDE EACH CELL PLENUM WALKWAY: YES, ELEVATED STAINLESS WALKWAY ABOVE BASIN INSIDE EACH CELL DAVIT CRANE: YES, ONE PER CELL EXTENDED LUBE LINES (IF NECESSARY TO MAINTAIN MOTOR): YES AQUASTAT FOR SUMP HEATER PROVIDED BY: MANUFACTURER TYPE OF WATER LEVEL CONTROL (FLOAT, ELECTRONIC, NONE): ELECTRONIC WATER LEVEL CONTROLS LOW WATER INTERLOCK FOR SUMP HEATER PROVIDED BY: MANUFACTURER PHYSICAL DIMENSIONS LENGTH X WIDTH X HEIGHT (IN): 169" X 229" X 144" (EACH CELL) SERVICE & AIRFLOW CLEARANCE (FRONT/REAR/LEFT/RIGHT/TOP) (IN): 144" / 144" / 36" / 36" / 36" ORIENTATION (CONVENTION) (LEFT HAND, RIGHT HAND, STANDARD): RIGHT HAND, STANDARD OPERATING WEIGHT, INCLUDE FLUID & BASE WEIGHT (LBS): 32,000 (1 PER CELL) LEAVING WATER CONN. SIZE, QUAN, TYPE (IN, PSI/GROOVED/FLANGED): 1 @ 16" FL PER CELL ENTERING WATER CONN. SIZE, QUAN, TYPE (IN, PSI/GROOVED/FLANGED): 1 @ 16" FL PER CELL EQUALIZER PIPE CONNECTION SIZE (IN): 12" PER CELL EQUALIZER PIPE LOCATION (LEFT/RIGHT SIDE, BOTTOM): BOTTOM ALL CELLS MAKEUP WATER CONN. SIZE, TYPE (IN, PSI/GROOVED/FLANGED): 4" FL PER CELL DRAIN CONNECTION SIZE, QUAN, TYPE (IN, PSI/GROOVED/FLANGED): 4" FL PER CELL OVERFLOW CONNECTION SIZE, TYPE (IN, PSI/GROOVED/FLANGED): 4" FL PER CELL PERFORMANCE DESIGN FLOWRATE (GPM): 2,400 PER CELL AVAILABLE WATER FLOW (Y/N): YES MINIMUM OPERATING FLOWRATE (GPM): 1,680 PER CELL AMBIENT DESIGN SUMMER WETBULB (F): 78 TOWER ENTERING WATER TEMPERATURE (F): 91 TOWER LEAVING WATER TEMPERATURE (F): 81 TOWER ENTERING WATER REQUIRED PRESSURE (FT. HD.): 17 (GRAVITY FED) TOTAL FAN AIRFLOW PER TOWER (CFM): 512,900 DESIGN FAN SPEED (RPM): 514 MAXIMUM FAN BRAKE POWER (HP): 3 @ 65 BHP EVAPORATION RATE (GPM): 81.6 FAN MOTOR EFFICIENCY RATING (%NPH): 95.4 FAN MOTOR TO BE INVERTER DUTY?: YES FAN MOTOR MINIMUM EFFICIENCY (% BY NEMA STD MG1-1. 12): PREMIUM ELECTRICAL QUANTITY OF ELECTRICAL CONNECTIONS: 1 PER CELL VOLTAGE/PHASE FOR EACH CONNECTION: 460V / 3 PH QUANTITY OF FANS PER TOWER: 1 PER CELL FAN MOTOR HORSEPOWER: 30 BHP FAN BRAKE HORSEPOWER: 29.4 KW ELECTRIC SUMP HEATER ACCESSORY (W): YES ALTERNATE HEAT ON RANGE TEMPERATURE (F): BY EFFECTIVE HEAT ALTERNATE POWER SOURCE PROVIDED BY: MANUFACTURER VARIABLE FREQUENCY DRIVE PROVIDED BY: VFD WITH BYPASS START SEQUENCE BY: MANUFACTURER DISCONNECT SWITCH (MANUAL/AUTO) (Y/N): MANUFACTURER MAIN CIRCUIT AMPACITY (MCA, AMPS): 42 / 108 MINIMUM CIRCUIT AMPACITY (MCA, AMPS): 2 @ 108 S/N: 10169877-A2

MARLEY 800-TON COOLING TOWER CELL WITH DRIVES, EQUALIZATION PIPING, SS BASINS, ACCESS WALKWAYS. UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. MANUFACTURER: MARLEY MODEL NUMBER: NC NUMBER OF SEPARATELY OPERABLE CELLS PER TOWER: 3 COMMON SUMP FOR MULTI-CELL TOWER(S)? (YES/NO): 2 SEPARATE CELLS WITH EQUALIZER PIPING MATERIALS OF CONSTRUCTION (TOWER BASIN, STRAINER): STAINLESS STEEL HOT WATER AND COLD WATER BASINS MATERIALS OF CONSTRUCTION (TOWER CASING): GALVANIZED STEEL MATERIALS OF CONSTRUCTION (FAN BLADES): ALUMINUM DRIVE TYPE: GEAR BASIN SWEEP ACCESSORY (YES/NO): YES, FACTORY INSTALLED WATER TREATMENT ACCESSORY (DESCRIBE): BASIN SWEEP SAFETY GUARDRAILS: YES, PERIMETER GUARDRAIL SYSTEM ON ENTIRE FAN DECK ACCESS LADDER ACCESSORY (INSIDE/OUTSIDE/NONE): YES, ACCESS LADDER TO TOP OF EACH FAN DECK INTERNAL ACCESS LADDER ACCESSORY: YES, ACCESS LADDER WITH SERVICE PLATFORM INSIDE EACH CELL PLENUM WALKWAY: YES, ELEVATED STAINLESS WALKWAY ABOVE BASIN INSIDE EACH CELL DAVIT CRANE: YES, ONE PER CELL EXTENDED LUBE LINES (IF NECESSARY TO MAINTAIN MOTOR): YES AQUASTAT FOR SUMP HEATER PROVIDED BY: MANUFACTURER TYPE OF WATER LEVEL CONTROL (FLOAT, ELECTRONIC, NONE): ELECTRONIC WATER LEVEL CONTROLS LOW WATER INTERLOCK FOR SUMP HEATER PROVIDED BY: MANUFACTURER PHYSICAL DIMENSIONS LENGTH X WIDTH X HEIGHT (IN): 169" X 229" X 144" (EACH CELL) SERVICE & AIRFLOW CLEARANCE (FRONT/REAR/LEFT/RIGHT/TOP) (IN): 144" / 144" / 36" / 36" / 36" ORIENTATION (CONVENTION) (LEFT HAND, RIGHT HAND, STANDARD): RIGHT HAND, STANDARD OPERATING WEIGHT, INCLUDE FLUID & BASE WEIGHT (LBS): 32,000 (1 PER CELL) LEAVING WATER CONN. SIZE, QUAN, TYPE (IN, PSI/GROOVED/FLANGED): 1 @ 16" FL PER CELL ENTERING WATER CONN. SIZE, QUAN, TYPE (IN, PSI/GROOVED/FLANGED): 1 @ 16" FL PER CELL EQUALIZER PIPE CONNECTION SIZE (IN): 12" PER CELL EQUALIZER PIPE LOCATION (LEFT/RIGHT SIDE, BOTTOM): BOTTOM ALL CELLS MAKEUP WATER CONN. SIZE, TYPE (IN, PSI/GROOVED/FLANGED): 4" FL PER CELL DRAIN CONNECTION SIZE, QUAN, TYPE (IN, PSI/GROOVED/FLANGED): 4" FL PER CELL OVERFLOW CONNECTION SIZE, TYPE (IN, PSI/GROOVED/FLANGED): 4" FL PER CELL PERFORMANCE DESIGN FLOWRATE (GPM): 2,400 PER CELL AVAILABLE WATER FLOW (Y/N): YES MINIMUM OPERATING FLOWRATE (GPM): 1,680 PER CELL AMBIENT DESIGN SUMMER WETBULB (F): 78 TOWER ENTERING WATER TEMPERATURE (F): 91 TOWER LEAVING WATER TEMPERATURE (F): 81 TOWER ENTERING WATER REQUIRED PRESSURE (FT. HD.): 17 (GRAVITY FED) TOTAL FAN AIRFLOW PER TOWER (CFM): 512,900 DESIGN FAN SPEED (RPM): 514 MAXIMUM FAN BRAKE POWER (HP): 3 @ 65 BHP EVAPORATION RATE (GPM): 81.6 FAN MOTOR EFFICIENCY RATING (%NPH): 95.4 FAN MOTOR TO BE INVERTER DUTY?: YES FAN MOTOR MINIMUM EFFICIENCY (% BY NEMA STD MG1-1. 12): PREMIUM ELECTRICAL QUANTITY OF ELECTRICAL CONNECTIONS: 1 PER CELL VOLTAGE/PHASE FOR EACH CONNECTION: 460V / 3 PH QUANTITY OF FANS PER TOWER: 1 PER CELL FAN MOTOR HORSEPOWER: 30 BHP FAN BRAKE HORSEPOWER: 29.4 KW ELECTRIC SUMP HEATER ACCESSORY (W): YES ALTERNATE HEAT ON RANGE TEMPERATURE (F): BY EFFECTIVE HEAT ALTERNATE POWER SOURCE PROVIDED BY: MANUFACTURER VARIABLE FREQUENCY DRIVE PROVIDED BY: VFD WITH BYPASS START SEQUENCE BY: MANUFACTURER DISCONNECT SWITCH (MANUAL/AUTO) (Y/N): MANUFACTURER MAIN CIRCUIT AMPACITY (MCA, AMPS): 42 / 108 MINIMUM CIRCUIT AMPACITY (MCA, AMPS): 2 @ 108 S/N: 10169877-A1

TACO 5100 GPM AIR SEPARATOR, NEVER USED UNDER LOAD. UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. DESIGNED AND CONSTRUCTED PER ASME CODE SECTION VIII DIV. 1. REGISTERED WITH THE NATIONAL BOARD OF PRESSURE VESSEL MANUFACTURERS. STANDARD DESIGN PRESSURE AND TEMPERATURE: 125 PSI @ 240F. OPTIONAL DESIGN PRESSURE AND TEMPERATURE: 150 PSI @ 240F. PARTICLE REMOVAL DOWN TO 5 MICRONS. CONSTRUCTION: CARBON STEEL WITH EXTERIOR RED OXIDE PRIMER FINISH. 304 STAINLESS STEEL COALESCENCE PALL RINGS. TACO 4900 UNITS ARE DESIGNED TO BE SELF-SUPPORTING IN THE PIPING SYSTEM. FACTORY REVIEW IS NECESSARY SHOULD ANY PIPING LOADS BE PRESENT.

PIPING FLANGES, CONTROL, VALVES, ETC. CHILLED WATER AND CONDENSER WATER PIPING 16", 14", 12", 10", 8", AND 6" CHW PIPING, GROOVED CONTROL VALVES, ISOLATION VALVES, BALANCING VALVES, BUTTERFLY VALVES. METER SCHEDULE -WATER-FLOW HEAT TRANSFER BUILDING FLOW METER 225B 8" 0-2000 GPM BACNET MS/TP 24VDC PIPE MOUNT FLOWRATE & TOTALIZER YES BACNET MS/TP 4-20MA (ANALOG) MECHANICAL ROOM MODBUS RTU - WATER-FLOW CHILLED WATER CH-1 FLOW METER 225B 6" 0-2000 GPM BACNET MS/TP 24VDC PIPE MOUNT FLOWRATE & TOTALIZER YES BACNET MS/TP 4-20MA (ANALOG) MECH. ROOM MODBUS RTU - WATER-FLOW CHILLED WATER CH-2 (FUTURE) FLOW METER 225B 6" 0-2000 GPM BACNET MS/TP 24VDC PIPE MOUNT FLOWRATE & TOTALIZER YES BACNET MS/TP 4-20MA (ANALOG) MECH. ROOM MODBUS RTU - WATER-CHECK COOLING TOWER BLOWDOWN CT-1 FLOW METER 225B 3" 0-200 GPM BACNET MS/TP 24VDC - PIPE MOUNT FLOWRATE & TOTALIZER YES BACNET MS/TP 4-20MA (ANALOG) NEAR COOLING TOWER MODBUS RTU WATER-CHECK COOLING TOWER BLOWDOWN CT-2 (FUTURE) FLOW METER 225B 3" 0-200 GPM BACNET MS/TP 24VDC PIPE MOUNT FLOWRATE & TOTALIZER YES BACNET MS/TP 4-20MA (ANALOG) NEAR COOLING TOWER MODBUS RTU - WATER-CHECK POTABLE WATER FLOW METER 225B 3" 0-200 GPM BACNET MS/TP 24VDC PIPE MOUNT FLOWRATE & TOTALIZER YES BACNET MS/TP 4-20MA (ANALOG) NEAR ENTRANCE MODBUS RTU - WATER-CHECK MAKE-UP WATER FLOW METER 225B 3" 0-200 GPM BACNET MS/TP 24VDC PIPE MOUNT FLOWRATE & TOTALIZER YES BACNET MS/TP 4-20MA (ANALOG) NEAR ENTRANCE MODBUS RTU. VALVE SCHEDULE V-1 3" COOLING TOWER BLOWDOWN BALL VALVE MECH. ROOM 150 THREADED FNPT LEVER HANDLE NIBCO T-585-70-LF - V-2 3" COOLING TOWER BLOWDOWN (FUTURE) BALL VALVE MECH. ROOM 150 THREADED FNPT LEVER HANDLE NIBCO T-585-70-LF - V-3 6" CHILLED WATER SUPPLY BUTTERFLY VALVE MECH. ROOM 150 FLANGED - GEAR OPERATOR BRAY SERIES 30 - V-4 6" CHILLED WATER RETURN BUTTERFLY VALVE MECH. ROOM 150 FLANGED - GEAR OPERATOR BRAY SERIES 30 - V-5 8" HEATING WATER SUPPLY BUTTERFLY VALVE MECH. ROOM 150 FLANGED - GEAR OPERATOR BRAY SERIES 30 - V-6 8" HEATING WATER RETURN BUTTERFLY VALVE MECH. ROOM 150 FLANGED - GEAR OPERATOR BRAY SERIES 30.

2019 CUSTOM ALLIANCE AIR PRODUCTS AHU'S, COOLING ONLY, SPARK PROOF, 57,000 CFM (AHU 1). UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. SPECIFICATIONS: MODEL: MAWS-114-25-HB-FFF-CW-AS-PF MAX. AMPERE RATING OF SUPPLY FUSES: 110A MIN. SUPPLY CONDUCTOR AMPACITY: 90A SUPPLY FAN 30 HP, 460V, 3 PHASE, F.L.A 37.5, QUANTITY OF 2 CONTROL TRANS. 460V, 1 PHASE, F.L.A 2.87, QUANTITY OF 1 OVERALL ELEC. RATING, 3: 460 V, 77.17 A OVERALL ELEC. RATING, 1: 460 V INCLUDES SHOWN VALVE STATIONS ALUMINUM ENCLOSURES INTEGRAL DAMPERS S/N: 2691AHU01

AMTROL 12,000 GAL SYSTEM RATED EXPANSION TANK WITH GLYCOL RELIEF COLLECTION, NEVER USED UNDER LOAD. UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. SPECIFICATIONS: 125 PSIG WORKING PRESSURE CONSTRUCTION SHELL ASME APPROVED STEEL BLADDER DESIGN FULL ACCEPTANCE; REPLACEABLE BLADDER THICKNESS .100 IN MINIMUM SYSTEM CONNECTION NPTF MALLEABLE IRON FINISH RED OXIDE PRIMER AIR VALVE SCHRADER VALVE W/EPDM SEATS FACTORY PRECHARGE 12 PSIG (.8 BAR) PERFORMANCE MAXIMUM OPERATING TEMPERATURE 240F (115C) MAXIMUM WORKING PRESSURE 125 PSIG (8.6 BAR)

MAKE-UP WATER STATION INCLUDING: (2) RPBPS, CHECK VALVES, STRAINERS, ISOLATION AND BYPASS VALVES. SPECIFICATIONS: WILKINS 375A 2 1/2 65 13 DUCTILE IRON ASTM A 536 GRADE 4 DUCTILE IRON ASTM A 536 GRADE 4 FDA APPROVED ELECTROSTATIC EPOXY STAINLESS STEEL, 300 SERIES, NORYL STAINLESS STEEL, 300 SERIES EPDM (FDA APPROVED) BUNA NITRILE (FDA APPROVED) STAINLESS STEEL, BRAIDED HOSE

BELL & GOSSETT VSC RHR MODEL 8X10X10.5B 10.5SSF PUMP WITH AMERICAN WHEATLEY SD12X10 SUCTION DIFFUSER. NEVER USED UNDER LOAD. UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. SPECIFICATIONS: 2400 GPM 96 FT.W.C. ABB DRIVES

2019 CUSTOM ALLIANCE AIR PRODUCTS AHU'S, COOLING ONLY, SPARK PROOF, 57,000 CFM (AHU 3). UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. MODEL: MAWS-114-25-HB-FFF-CW-AS-PF MAX. AMPERE RATING OF SUPPLY FUSES: 110A MIN. SUPPLY CONDUCTOR AMPACITY: 90A SUPPLY FAN 30 HP, 460V, 3 PHASE, F.L.A 37.5, QUANTITY OF 2 CONTROL TRANS. 460V, 1 PHASE, F.L.A 2.87, QUANTITY OF 1 OVERALL ELEC. RATING, 3: 460 V, 77.17 A OVERALL ELEC. RATING, 1: 460 V INCLUDES SHOWN VALVE STATIONS ALUMINUM ENCLOSURES INTEGRAL DAMPERS S/N: 2691AHU03

2019 CUSTOM ALLIANCE AIR PRODUCTS AHU'S, COOLING ONLY, SPARK PROOF, 57,000 CFM (AHU 4). UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. SPECIFICATIONS: MODEL: MAWS-114-25-HB-FFF-CW-AS-PF MAX. AMPERE RATING OF SUPPLY FUSES: 110A MIN. SUPPLY CONDUCTOR AMPACITY: 90A SUPPLY FAN 30 HP, 460V, 3 PHASE, F.L.A 37.5, QUANTITY OF 2 CONTROL TRANS. 460V, 1 PHASE, F.L.A 2.87, QUANTITY OF 1 OVERALL ELEC. RATING, 3: 460 V, 77.17 A OVERALL ELEC. RATING, 1: 460 V INCLUDES SHOWN VALVE STATIONS ALUMINUM ENCLOSURES INTEGRAL DAMPERS S/N: 2691AHU04

2019 CUSTOM ALLIANCE AIR PRODUCTS AHU'S, COOLING ONLY, SPARK PROOF, 57,000 CFM (AHU 6). UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. SPECIFICATIONS: MODEL: MAWS-114-25-HB-FFF-CW-AS-PF MAX. AMPERE RATING OF SUPPLY FUSES: 110A MIN. SUPPLY CONDUCTOR AMPACITY: 90A SUPPLY FAN 30 HP, 460V, 3 PHASE, F.L.A 37.5, QUANTITY OF 2 CONTROL TRANS. 460V, 1 PHASE, F.L.A 2.87, QUANTITY OF 1 OVERALL ELEC. RATING, 3: 460 V, 77.17 A OVERALL ELEC. RATING, 1: 460 V INCLUDES SHOWN VALVE STATIONS ALUMINUM ENCLOSURES INTEGRAL DAMPERS S/N: 2691AHU06

GRISWOLD INTEGRA CLEAN TOWER CLEANING SYSTEM, SIZED FOR 3RD TOWER CELL, CHEMICAL FREE. UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. SPECIFICATIONS: TAG: CWS-1 INTEGRACLEAN SIDE-STREAM FILTRATION & WATER TREATMENT SYSTEM GLS-801 CENTRIFUGAL SEPARATOR WITH BLOW DOWN ELECTRICAL PANEL WITH NEMA 4X ENCLOSURE 65K AIC SCCR CHEMICAL FREE WATER TREATMENT & SOLIDS MANAGEMENT WAVE 2.0 NON-CHEMICAL WATER TREATMENT TECHNOLOGY (WAVE FIELD INSTALLED IN PIPING) MICROPROCESSOR CONTROLLER WITH INSTALERT REMOTE MONITORING DESIGNED CAPACITY FOR THE ADDITION OF A 3RD TOWER, 7200 GPM

800 TON YORK CENTRIFUGAL CHILLERS MODEL YKL7LGH9-UEHS, NEW, NEVER USED UNDER LOAD. UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. 800-TON CENTRIFUGAL COMPRESSOR WITH FACTORY INSTALLED VFD R-134A REFRIGERANT ALL CHILLED WATER AND CONDENSER WATER CONNECTIONS ARE VICTAULIC CONNECTIONS VARIABLE PRIMARY FLOW CONTROLS HOT GAS BYPASS FACTORY INSTALLED FLOW SWITCHES BACNET CONTROL INTERFACE UL LISTED, 460VAC/60HZ EVAP. COND. REFRIG. DWP, PSIG: 235 235 LIQUID DWP, PSIG: 150 150 NO. OF PASSES: 2 2 TUBE DESCRIPTION: 656 471 CONDENSER GAS INLET: BAFFLE REFRIGERANT: R-134A CHARGE, LBS: 2254 VOLTS-PHASE-HZ FLA OIL PUMP 2 HP 460-3-60 3.6 OIL HEATER N/A 460-3-60 3.0 S/N: SEGM-361770

2012 MINDA DUAL STACKER - 12' STACKER AND 1- 40' STACKER. THE 40' STACKS SINGLES AND THE 12' STACKS LAYERS. LOBO SAW FOR CUTTING LONG LENGTHS TO THE 12' LENGTHS. SIEMENS PLC DISCHARGE TRANSPORT SYSTEM, FINGER JOINT PLANT. TRANSPORT OF THE LAMELLAE ON THE ROLLER CONVEYORS DOWNSTREAM OF THE FINGER JOINT PLANT IS SYNCHRONIZED WITH THE OPERATION OF THE FINGER JOINT PLANT. AFTER THE CROSS-CUT, THE LAMELLA IS TRANSPORTED AT AN INCREASED SPEED UP TO THE END OF THE ROLLER CONVEYORS. STACKER 1: IF THE LAMELLA IS INTENDED FOR AUTOMATIC STACKER 1, IT IS TAKEN OVER BY THE CAM CHAIN CONVEYOR AND SUBSEQUENTLY TRANSFERRED TO THE AUTOMATIC STACKER. WHEN THE STACK HEIGHT IS REACHED, THE STACK IS LOWERED AND THEN TRANSFERRED TO THE CHAIN CONVEYOR. WHEN THE MAXIMUM NUMBER OF STACKS IS REACHED, THE ENTIRE PACKAGE IS MOVED ON TO THE DISCHARGE CHAIN CONVEYOR. FEED, STACKER 2: IF THE LAMELLA IS INTENDED FOR AUTOMATIC STACKER 2, THE LAMELLA IS LIFTED UP BY A ROLLER RAIL AND TRANSPORTED ONTO THE ROLLER CONVEYOR UPSTREAM OF THE SAW. THE LAMELLA IS THEN ALIGNED AGAINST A STOP AND CUT. FOLLOWING THE SAW CUT, THE SHORTENED LAMELLA IS ALIGNED AGAINST A SECOND STOP AND THEN FED TO THE AUTOMATIC STACKER VIA A TRANSPORT BELT. STACKER 2: ONCE THE LAYER IS COMPLETE, IT IS RAISED AND TRANSPORTED FORWARD. SUBSEQUENTLY THE LAYER IS LOWERED DOWN TO THE EXISTING STACK. THE LANCES THEN MOVE BACK AND THE LAYER IS THUS DEPOSITED. WHEN THE STACK REACHES THE REQUIRED HEIGHT, THE STACK IS TRANSPORTED TO THE REMOVAL POSITION. S/N: 740075

2023 USNR MULTI SAW TRIMMER, 16 FT RH PM CLAMSHELL, NEW, NEVER USED. LUMBER SIZES: LENGTHS (BEFORE TRIMMER): 6 FT TO 16 FT LENGTHS (AFTER TRIMMER): 2FT TO 16FT P.E.T. LENGTHS: SEE -LL DRAWING FOR RANGES WIDTHS: 4" TO 8" THICKNESS: 1" TO 2" MAXIMUM PIECE SIZE: 2" X 8" X 16 FT 6FT THRU 16 FT TO SORTER 2FT, 3FT, AND 4FT DROP OUT AT GATE AFTER TRIMMER SPECIES: DRIED SPF SYSTEM MAX PEAK SPEEDS: 140 LPM 2X4 130 LPM 2X6 90 LPM 2X8 TRIMMER SUB-ASSEMBLY OPTION MATRIX: 16FT, RIGHT HAND, PLANER MILL TRIMMER ASSEMBLY: 10553-0114-C TRIMMER INTERNALS: 10553-0114-A P.E.T. SAW ASSY: 472629 P.E.T. ADJUSTMENT: 519195 LINESHAFTS: SEE 10553-0114-A HOLD DOWN KIT: SEE 10553-0114-B SKIRTING: 609932-PR16 INFEED SKIRTING 609933-PR16 OUTFEED SKIRTING S/N: 10553-0114

GILBERT PRODUCTS S-SERIES PLANER SPLITTING MODULES, FEED TABLE, BRIDGE & FEED DECKS, TRANSFER ASSEMBLY, AND ALL ELECTRICAL CONTROL CABINETS, SERVOS - NEW, NEVER USED. SPECIFICATIONS: FEED MECHANISM OUTFEED ROLLS TWO POLISHED EXIT ROLLS, CHROMED, 12-INCH DIAMETER. ALL FEED ROLLS ARE ASSEMBLED CANTILEVER FOR QUICK ACCESS. FEED ROLLS ARE DRIVEN BY NEW MOTORIZATION. CHROMED PLATES ONE (1) CENTRAL ADJUSTABLE FEED PLATE INTEGRATED TO FRAME. ONE (1) EXIT FEED PLATE. ALL FEED PLATES WITH INTERCHANGEABLE CHROMED WEAR PLATES. ALIGNMENT RULERS (GUIDE BAR) ONE (1) ENTRY RULER, ZERO LINE ATTACHED TO FRAME, WITH MANUAL ADJUSTMENT OF ALIGNMENT AND RIGID MECHANICAL LOCKS. ONE (1) EXIT RULER. ALL RULERS ARE CHROMED. FOOT PRESSERS (CHIP BREAKERS) ENTRY FOOT PRESSERS ARE ASSEMBLED ON PARALLELOGRAM SYSTEMS ON ROTATION POINT. EXIT FOOT PRESSERS. DISPLACEMENT, ADJUSTMENT AND PRESSURE ARE CONTROLLED BY PNEUMATIC CYLINDERS, FOR QUICK RELEASE. ALL FOOT PRESSES ARE MACHINED AND CHROMED. PROFILE MODULE DESCRIPTION STURDY MODULAR STEEL FRAME, 2-INCH MINIMUM THICKNESS, ALLOWS EASIER MAINTENANCE, REDUCES THE TIME OF ADJUSTMENT AND SET-UP AND GIVES FULL ACCESS TO LUMBER. FRAME IS STRESS-RELIEVED TO ENSURE OPTIMAL OPERATION. LATERAL DISPLACEMENT ON LINEAR BEARINGS MUCH EASIER TO ADJUST THE TOOL POSITION, MORE PRECISE. SPEEDS OBTAINED WITH BIGGER MOTORS WITH VFDS EASED EDGES WITH VFDS 2-INCH THICKNESS USING BOTTOM BLADE ONLY SPLITTING IN 2 PIECES: 1200 FPM UP TO 1800 FPM USING TOP AND BOTTOM BLADE. STRAIGHT CUT WITH VFDS 2-INCH THICKNESS SPLITTING IN 2 PIECES: 1800 FPM CUTTERHEADS SIMILAR CUTTERHEADS AS THE PLANER CAN BE USED. ONE (1) BOTTOM CUTTERHEAD CAN BE MOUNTED ON HIGH ROTATION MOTOR. ONE (1) TOP CUTTERHEAD CAN BE MOUNTED ON HIGH ROTATION MOTOR. THE CUTTERHEAD CAN BE LOCKED IN PLACE HYDRAULICALLY WITH HYDRO GRIP SYSTEM AND MOUNTED WITH NON-SLIP SECURITY COLLAR. POWER OF ELECTRIC MOTOR IS AS FOLLOWS: 150 HP ON TOP CUTTERHEAD. 100 HP ON BOTTOM CUTTERHEAD. VERTICAL SPLITTING MODULE SIDE HEAD SECTION USED FOR SPLITTING 1) SECOND SIDE HEAD SECTION, RIGHT AND LEFT SIDE HEADS FOR SPLITTING 2) HIGH ROTATION HEAD BEARING ASSEMBLIES 3) 3600 RPM MOTORS, VFD DRIVEN, MOTORS CAN RUN TO 4500 RPM IF DESIRED 4) POWER FOR EACH SIDE SPLITTER, 100HP EACH 5) INCLUDES SECOND TOP AND BOTTOM HEAD SECTIONS (PROFILE AND SPLITTING) 6) (15) SERVO MOTORS FOR FINITE CONTROL AND ADJUSTMENT 7) (2) FEED DECKS GILBERT NEW, NEVER USED SPLITTER CONTROL CABINET, CONTROLS EQUIPMENT AND SERVOS SN: 3191128 SPECIFICATIONS: BOITER TYPE 4X AMP 70 HP 30 3 PHASE, 60 HZ 120/480 (2) GILBERT PRODUCTS TRANSFER ASSEMBLY, NEW, NEVER USED SPECIFICATIONS: ITEM 1 PART NO: 8201131 DESCRIPTION: #1 TRANSFER, 5 FT ITEM 2 PART NO: 8201139 DESCRIPTION #2 TRANSFER, 5 FT ITEM 3 PART NO: 8352427 DESCRIPTION: GUIDE ITEM 4 PART NO: 0613631 DESCRIPTION: HEX. BOLT ITEM 5 PART NO: 0811161 DESCRIPTION: HEX. NUT ITEM 6 PART NO: 0910116 DESCRIPTION: FLAT WASHER

2019 CUSTOM ALLIANCE AIR PRODUCTS AHU'S, COOLING ONLY, SPARK PROOF, 57,000 CFM (AHU 5). UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. SPECIFICATIONS: MODEL: MAWS-114-25-HB-FFF-CW-AS-PF MAX. AMPERE RATING OF SUPPLY FUSES: 110A MIN. SUPPLY CONDUCTOR AMPACITY: 90A SUPPLY FAN 30 HP, 460V, 3 PHASE, F.L.A 37.5, QUANTITY OF 2 CONTROL TRANS. 460V, 1 PHASE, F.L.A 2.87, QUANTITY OF 1 OVERALL ELEC. RATING, 3: 460 V, 77.17 A OVERALL ELEC. RATING, 1: 460 V INCLUDES SHOWN VALVE STATIONS ALUMINUM ENCLOSURES INTEGRAL DAMPERS S/N: 2691AHU05

2019 CUSTOM ALLIANCE AIR PRODUCTS AHU'S, COOLING ONLY, SPARK PROOF, 57,000 CFM (AHU 2). UNIT WAS STARTED UP, COMMISSIONED, AND THEN PUT INTO STORAGE MODE. HAS NEVER RUN UNDER LOAD. S/N: 2691AHU02 SPECIFICATIONS: MODEL: MAWS-114-25-HB-FFF-CW-AS-PF MAX. AMPERE RATING OF SUPPLY FUSES: 110A MIN. SUPPLY CONDUCTOR AMPACITY: 90A SUPPLY FAN 30 HP, 460V, 3 PHASE, F.L.A 37.5, QUANTITY OF 2 CONTROL TRANS. 460V, 1 PHASE, F.L.A 2.87, QUANTITY OF 1 OVERALL ELEC. RATING, 3: 460 V, 77.17 A OVERALL ELEC. RATING, 1: 460 V INCLUDES SHOWN VALVE STATIONS ALUMINUM ENCLOSURES INTEGRAL DAMPERS

TUBULAR RIVET MACHINE 3/4 HP SINGLE PHASE WITH DUAL PALM BUTTONS

GORTON P12 PANTOGRAPH MODEL GORTON P1-2 PANTOGRAPH WITH FONTS

15,000LB CAPACITY AIR OVER HYDRAULIC AXLE JACK SET. CAPACITY IS FOR BOTH JACKS. RUN ON 72 TO 116 PSI SHOP AIR. RATED AT 3500 PSI. JACKS HAVE A 8 INCH STROKE. EXTENSIONS ARE 1.5 INCH, 5 INCH, AND 9 INCH. EACH JACK HAS ITS OWN HYDRAULIC PUMP AND CAN OPERATE SEPARATELY. VALVE IN EACH LINE TO CLOSE THE CIRCUIT. JACKS CAN BE ADJUSTED FOR WIDTH. FRAME WIDTH IS 44 INCH AND WHEELS ARE 2 INCH WIDE.

LOCKFORMER SPEED NOTCHER WITH 5 HEADS, 3 PHASE S/N: VG-1632

LOCKFORMER SPEED NOTCHER WITH 5 HEADS, SINGLE PHASE

OSTER POWER PIPE THREADER MODEL 552NZ2044

TIGER VAC HEPA VACUUM 4D-16 TC RE HEPA WET ASBESTOS REMEDIATION - NEW. SPECIALIZED VACUUM CLEANER DESIGNED FOR WET ASBESTOS REMEDIATION. HEPA FILTER TO CAPTURE FINE DUST AND DEBRIS. IDEAL FOR SAFELY REMOVING CONTAMINATED MATERIALS. OFFERS POWERFUL SUCTION AND EFFICIENT CLEANING PERFORMANCE. 120 VOLT 17 AMP DIMENSIONS 29X30X56 AND 165LBS

CARLTON RADIAL DRILL, 3' ARM WITH 9" COLUMN, 7.5 HP, 440V 3 PHASE WITH BOX TABLE, VISE AND DRILL CHUCK

BRIDGEPORT CNC MILL 30 NMTB, 2 HP, 220/440 VOLT S/N: CNC3181

LEBLOND LATHE MODEL C7816 15 INCH SWING, 40 INCH BETWEEN CENTERS, 3 PHASE, 220/440V, 3 JAW CHUCK, LIVE CENTER, DRILL CHUCK, TOOLPOST, TAPER ATTACHMENT S/N: C7816

GL VISE 3" ROTATING

32 STATION ROTARY TABLET PRESS

140 QUART STAINLESS STEEL MIXING BOWL

32 STATION ROTARY TABLET PRESS

SAFELINE METTLER TOLEDO METAL DETECTOR

CAT 40 CNC TOOLS

CAT 40 CNC TOOLS

VISES