Electronic Lab Test Measurement Equipment Day 1 of 3 day event

HAKKO T7/T15-SB05 SOLDERING TIP FOR FM-202/FP-102 SPECIFICATIONS: PART #: T7/T15-SB05 TIP SHAPE: 0.5SB CONICAL SIZE: 0.5MM X 10.5MM FOR IRONS: HAKKO FM-203-HANDPIECE : HAKKO FM-2027(70W) HAKKO FM-204-HANDPIECE : HAKKO FM-2027(70W) HAKKO FX-950-HANDPIECE : HAKKO FM-2028(70W) HAKKO FX-951-HANDPIECE : HAKKO FM-2028(70W) HAKKO FX-952-HANDPIECE : HAKKO FM-2028(70W) HAKKO FM-202-HANDPIECE : HAKKO FM-2021(70W) OR HANDPIECE : HAKKO FM-2027(70W) NOTE: THE T15 TIPS HAVE REPLACED THE T7 TIPS. THE ONLY DIFFERENCE IS HAKKO HAS PHASED OUT THE BARCODE FROM THE TIPS. SEE THE HAKKO PRODUCT BULLETIN.

2016 YINHE WG055DC LARGE ENVIRONMENTAL/BURN-IN CHAMBER 34.5"W X 39"D X 70"H 480V 3PH - MANUFACTURER: YIN HE MODEL: WG055DC CONDITION: USED. THIS CHAMBER IS IN FAIR COSMETIC CONDITION. IT IS ONLY A FEW YEARS OLD, HAS UNDER 700 HOURS ON THE CLOCK, AND IS PRETTY CLEAN OVERALL. INSIDE THE AIR BLOWERS LOOK CLEAN. THERE ARE SOME AREAS WITH SIGNIFICANT SCRATCHING, INCLUDING ONE UGLY SPOT ON THE REAR DOOR INSIDE. THE TOP HAS LOTS OF DUST AND SOME RUSTY EDGES AND MOUNTING HARDWARE. SEVERAL SCREWS ARE MISSING FROM COVERS. THE CONTROLS ARE HIGH UP ON THE FRONT, AWAY FROM THE RISK OF UNTRAINED PERSONNEL MAKING ADJUSTMENTS. THERE IS A MULTI-COLOR STACK TOWER LIGHT, WHICH IS COVERED IN BLACK GOO FROM FOAM, FROM STORAGE. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS CHAMBER IS IN GOOD WORKING CONDITION AS FAR AS WE CAN TEST. WE ARE NOT 100% SURE HOW TO MAKE IT RUN PROPERLY, BUT WITH THE DAMPERS SET HOW THE PREVIOUS OWNER LEFT THEM, THIS UNIT WAS ONLY ABLE TO GET UP TO 41OC INSIDE. WE ARE PRETTY SURE THE FANS BLASTING AIR OUT THE TOP AND REAR PANEL, AS WELL AS THE VENTILATION DAMPERS BEING OPEN, PREVENTED THE TEMPERATURE FROM RISING ANY FURTHER. IT WAS HEATING QUICKLY FROM AMBIENT UNTIL IT STARTED TO SLOW AROUND THE MID-30 DEGREE RANGE. WE SET 40O AND IT SETTLED VERY SLOWLY AS IT CONTROLLED THE LAST DEGREE...WE GOT TIRED OF WAITING AFTER A FEW MINUTES AND TOOK A PICTURE AT 39.9O. THE DOORS DRAG THE FLOOR WITH THEIR PLASTIC SWEEPS, AND BOTH FRONT AND REAR DOORS CLOSE FIRMLY. THE DOORS LEAK. THE DAMPERS ON THE REAR PANEL LEAK. THE GAPS AROUND PANELS LEAK. THIS IS A VERY LEAKY CHAMBER. THE REAR WALL IS MOSTLY ADJUSTABLE DAMPERS TO ALLOW AIR OUT FROM THE BACK. THE SIDES ARE DOUBLE-LAYERS OF STEEL BUT NOT WELL INSULATED; THE OUTSIDE WAS WARM WHEN THE INSIDE WAS WARM. THE LARGE, DUAL BLOWERS PROVIDE AN EXTREMELY POWERFUL AND LOUD BLAST OF AIR ACROSS THE CHAMBER AT ALL TIMES. THE START, STOP, AND EMERGENCY STOP BUTTONS ALL WORK. THE REAR CHAMBER LAMP SWITCH IS A LITTLE FLAKY, IT DOESN'T ALWAYS STAY ON WHEN PRESSED BUT THE LAMP DOES LIGHT. THE FRONT CHAMBER'S SWITCH OR LAMP (OR BOTH) MAY BE FAULTY; THE FRONT CHAMBER LAMP DOES NOT ILLUMINATE. THE REAR PANEL FANS RUN. THE CONTROLLERS RESPOND TO USER INPUTS AS EXPECTED. THE HOURS METER CONSTANTLY SPINS. NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) YINHE WG055DC BURN-IN CHAMBER (1) OPERATION INSTRUCTIONS MANUAL, WITH SCHEMATICS SPECIFICATIONS: MANUFACTURER: CHONGQING YINHE EXPERIMENTAL EQUIPMENT CO., LTD. CHN MODEL: WG055DC PRE 2C CHAMBER ENVIRONMENTAL TEMPERATURE CHAMBER/BURN-IN CHAMBER ROLL-IN ACCESS, WIDE-OPENING FRONT DOOR (STEP-IN REAR DOOR) TEMPERATURE RANGE: ROOM TEMPERATURE +15 TO +55OC POWER: 480V 3PHASE 60HZ 47A 27KW WORK ROOM SPECIFICATION: 102 CM D X 119 CM W X 180 CM H LARGE! ASSEMBLED AS SHOWN: 79"W 95"D 124"H FRONT DOORS OPENING: 47"W X 71"H WIDTH OF WORKSPACE BETWEEN RAILS NEAR FLOOR: 34.5"W FLOOR DEPTH IN FRONT AREA: 39"D TOTAL FLOOR DEPTH: 61"D INNER/REAR OPENING: 30.5"W X 64"H BACK DOOR OPENING: 30"W X 66"H SIDE BAYS IN REAR CHAMBER: 18"W, 19" AND 25"D DUAL ABB 2KW BLOWERS SIEMENS PLC AND HMI INTERFACE DIGITAL TEMPERATURE AND OVERTEMPERATURE CONTROLS MOTORIZED INLET AND EXHAUST DAMPERS 125V 15A AND 250V 20A CONVENIENCE OUTLETS INSIDE LARGE VIEWING WINDOWS IN FRONT AND REAR DOORS STEEL CONSTRUCTION, DUAL-LAYER WALLS SEEM UNINSULATED (OUTSIDE GETS WARM!) MANUFACTURED: 2016 SKU: X41D004 6-BILR3(1) 4195LBS - 86IN X 82IN X 122IN

LEICA PLAN FLUOR LWD 100X EPI IK INFINITY MICROSCOPE OBJECTIVE BF/DF - MANUFACTURER: LEICA MODEL: PLAN FLUOR LWD 100X CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THIS OBJECTIVE IS IN GOOD COSMETIC CONDITION EXCEPT FOR A FEW SMALL SCUFFS/SCRATCHES IN THE METAL. THE GLASS LOOKS IN GOOD CONDITION. WE ARE NOT SURE WHAT SIZE TO CALL THE MOUNTING THREADS, BUT THEY ARE ABOUT 28MM OUTSIDE AND FIT IN A TURRET HOLE WITH A 27MM INSIDE DIAMETER (SEE PHOTO #6). THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS WAS REMOVED FROM A DECOMMISSIONED LEICA REICHERT POLYLITE 88 MICROSCOPE. THE VIEW THROUGH THIS LENS WAS CLEAR. NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) REICHERT 100X/0.90 OBJECTIVE LENS SPECIFICATIONS: MANUFACTURER: LEICA AG (REICHERT DIVISION) MICROSCOPE OBJECTIVE LENS BARREL TEXT READS: PLAN FLUOR 100X/0.90 EPI IK /0 MAGNIFICATION: 100X N.A.: 0.90 INFINITY CORRECTED FOR USE WITHOUT COVER SLIP BRIGHTFIELD OR DARKFIELD SKU: T37D014 3A-02-03(1) 2LBS - 8IN X 8IN X 4IN

[5] OMEGA JTSS-116U-72 LOW TEMPERATURE T/C ASSEMBLY PROBE. MANUFACTURER: OMEGA MODEL: JTSS-116U-72 CONDITION: NEW. COMES IN ORIGINAL PACKAGING. THESE ASSEMBLIES ARE IN NEW COSMETIC CONDITION AND COME IN THE ORIGINAL OMEGA BAG. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (5) OMEGA JTSS-116U-72 LOW TEMPERATURE T/C ASSEMBLY PROBE SPECIFICATIONS: MANUFACTURER: OMEGA MODEL: JTSS-116U-72 DESCRIPTION: LOW TEMPERATURE T/C ASSEMBLY SKU: T18H007 2I-06-02(1) 0LBS - 13IN X 9IN X 3IN

[VWR SCIENTIFIC 58816-121 STANDARD MINI VORTEXER] VWR SCIENTIFIC 58816-121 STANDARD MINI VORTEXER 120VAC 150W 50/60HZ 1PH 945300. USED. THIS VORTEXER IS IN GOOD COSMETIC CONDITION WITH SCUFFS AND SCRATCHES FROM REGULAR COMMERCIAL USE AND COMES IN NON-ORIGINAL PACKAGING. SOME ORANGE STAINS ON THE ENCLOSURE WE HAD DIFFICULTY TRYING TO REMOVE (SEE PHOTO). THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. WE POWERED ON THIS VORTEXER TO OBSERVE THE SHAKER SHAKE AND RESPONDED TO THE VARIABLE SPEED CONTROL AS DESIGNED. NO ADDITIONAL TESTING WAS PERFORMED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) VWR SCIENTIFIC 58816-121 STANDARD MINI VORTEXER 120VAC. SPECIFICATIONS: MANUFACTURER: VWR SCIENTIFIC CAT. #: 58816-121 DESCRIPTION: STANDARD MINI VORTEXER 120VAC 150W 50/60HZ 1PH 945300 300-3200 RPM CONTROL DIAL. SKU: Y09H016 1B-05-02(1) 14LBS - 12IN X 12IN X 12IN

OLYMPUS BH COMPOUND MICROSCOPE WITH VERTICAL ILLUMINATOR AND FULL OPTICS. OLYMPUS BH-SERIES COMPOUND MICROSCOPE. INVERTED VIEW. VERTICAL ILLUMINATOR WITH FIELD AND APERTURE IRISES. 5-PLACE ROTATING OBJECTIVE TURRET. 13 X 13 CM STAGE, 10 X 10 CM TRAVEL. EYEPIECES: 10X WIDEFIELD. OBJECTIVES: M 5X 0.1 MPLAN 10X 0.25 M 20X 0.40 M 40X 0.65. ADJUSTABLE PUPILLARY DISTANCE. DIOPTER ADJUSTABLE. POLARIZATION ANALYZER WITHOUT A POLARIZER, 0-45 DEGREES. H <--> L SLIDER IN ILLUMINATOR. 115V POWER FOR ILLUMINATOR, RED GLOWING POWER SWITCH.

LEICA WETZLAR 036-085.021NR & 020-675.102 VERTICAL ILLUMINATORS - PARTS (2) - MANUFACTURER: LEICA WETZLAR MODEL: 036-085.021NR & 020-675.102 CONDITION: FOR PARTS OR NOT WORKING. COMES IN NON-ORIGINAL PACKAGING. THESE ILLUMINATORS ARE IN GOOD COSMETIC CONDITION WITH OBVIOUSLY MISSING PARTS AS SHOWN. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THE GLASS LOOKS IN GOOD CONDITION. WE ARE NOT ABLE TO TEST THE MOVING PARTS WITHOUT A CONTROLLER. BECAUSE OF THIS, WE ARE SELLING THEM AS/IS. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) LEICA WETZLAR 036-085.021NR VERTICAL ILLUMINATORS (1) LEICA WETZLAR 020-675.102 VERTICAL ILLUMINATORS SPECIFICATIONS: MANUFACTURER: LEICA WETZLAR 036-085.021NR VERTICAL ILLUMINATOR USED WITH AN ORBOT WAFER INSPECTION SYSTEM SKU: X29S006 2O-08-03(1) 11LBS - 16IN X 16IN X 16IN

[OWL SEPARATION SYSTEMS B2 EASYCAST MINI GEL ELECTROPHORESIS SYSTEM 2 COMB SLOTS] RATED 0-150V, 0-100MA CLASS II. THIS ELECTROPHORESIS SYSTEM IS IN GOOD COSMETIC CONDITION WITH SCUFFS AND SCRATCHES FROM REGULAR COMMERCIAL USE AND COMES IN NON-ORIGINAL PACKAGING. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. THIS ELECTROPHORESIS SYSTEM WAS REMOVED FROM A DECOMMISSIONED ENVIRONMENT AND HAS NOT BEEN TESTED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) OWL SEPARATION SYSTEMS B2 EASYCAST MINI GEL ELECTROPHORESIS SYSTEM 2 COMB SLOTS SPECIFICATIONS: MANUFACTURER: OWL SEPARATION SYSTEMS MODEL: B2 EASYCAST MINI GEL ELECTROPHORESIS SYSTEM 2 COMB SLOTS RATED 0-150V, 0-100MA CLASS II 5LBS - 16IN X 12IN X 8IN

[OLYMPUS U-D6REM] MICROSCOPE OBJECTIVE TURRET MOTORIZED NOSEPIECE (6) OBJECTIVE LENS POSITIONS RMS LENS MOUNTING THREAD COMPATIBLE WITH: BX AND MX SERIES (40.5MM DOVETAIL WIDTH) SLOT FOR FILTER OR ANALYZER INSERT (NO INSERT INCLUDED) REQUIRES SEPARATE CABLE AND CONTROLLER (NOT INCLUDED)

[AGILENT 81110A] PULSE/PATTERN GENERATOR 2X 81110A 1MHZ/330MHZ DIFFERENTIAL BNC - MANUFACTURER: AGILENT TECHNOLOGIES MODEL: 81110A PULSE-/PATTERN GENERATOR NUMBER OF CHANNELS: 2 WITH 81112A MODULES INSTALLED FREQUENCY RANGE: 1 MHZ ... 330 MHZ DIFFERENTIAL BNC OUTPUTS TRIGGERABLE / PLL OPERATION SELECTABLE PULSE / BURST / PATTERN MODES SELECTABLE SELF-CAL FOR IMPROVED TIMING ACCURACY SELECTABLE EDGES, 800 PS OR 1.6 NS OUTPUT IMPEDANCE: 50 OHMS PROVIDES UP TO 3.8 VPP INTO 50 OHMS VARIABLE DELAY RANGE: 1.515 ... 999.5 S WITH FEET AND BUMPERS FRONT-AND-BACK POWER: 100-120 V, 50-60HZ/400HZ , OR 200-240 V, 50-60 HZ, 170VA

[BECTON DICKINSON 351005 FALCON OPTILUX DISPOSABLE PETRI DISH] MANUFACTURER: BECTON DICKINSON MODEL: 351005 CONDITION: USED. COMES IN ORIGINAL PACKAGING. THIS ITEM IS IN NEW AND UNUSED CONDITION. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (6) BAGS OF 20 BECTON DICKINSON 351005 FALCON OPTILUX DISPOSABLE PETRI DISH SPECIFICATIONS: MANUFACTURER: BECTON DICKINSON MODEL: 351005 DESCRIPTION: FALCON OPTILUX DISPOSABLE PETRI DISH FLAT BOTTOM SURFACE FOR DISTORTION-FREE OPTICS DIMENSIONS: DIAMETER: 100MM HEIGHT: 20MM MATERIAL: CRYSTAL-GRADE POLYSTYRENE DISPOSABLE STERILE SKU: X06G002 2H-02-04(1) 12LBS - 22IN X 15IN X 15IN

(LOT OF 4) NEW ENPLAS OTS-28-1.27-04 OPEN-TOP SOP TEST & BURN-IN IC SOCKETS - MANUFACTURER: ENPLAS MODEL: OTS-28-1.27-04 CONDITION: NEW OTHER. COMES IN NON-ORIGINAL PACKAGING. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (4) ENPLAS OTS-28-1.27-04 OPEN-TOP SOP TEST SOCKETS SPECIFICATIONS: MANUFACTURER: ENPLAS PART #: OTS-28-1.27-04 SOCKET TYPE: SOP PINCH CONTACT (OPEN-TOP) LEAD COUNT: 28 PITCH: 1.27 MM MAX. ACTUATION FORCE: 1.7KG DIMENSIONS: LENGTH: 25.4 MM WIDTH: 27.0 MM HEIGHT: 17.0 MM LEAD LENGTH: 2.5 MM

[THERMOTEK T255P] SOLID-STATE RECIRCULATING CHILLER 210W COOLING CAPCACITY 50% SMALLER/LIGHTER THAN COMPRESSOR UNIT OF SIMILAR CAPACITY PRECISE TEMPERATURE CONTROL FROM -5 TO +45 OC STABILITY RATING: 0.1 OC SMART DIGITAL CONTROLLER SIMPLE UP/DOWN BUTTON CONTROLS FOR TEMPERATURE SETTING LIQUID FITTINGS: 1/4" NPT (FEMALE) RS-232 COMPUTER INTERFACE (NOT REQUIRED TO USE) NON-VOLATILE MEMORY SET TEMPERATURE 1GPM OPEN FLOW RATING MINIMUM DESIGN FLOW RATING: 0.2 GPM SYSTEM FLUID CAPACITY: 15 OZ POWER REQUIREMENT: 100-240V 50/60HZ 7.5A 625W LIFETIME HOURS: 4763:30 FOR INDOOR USE ONLY 22LBS - 22IN X 15IN X 15IN

MILLIPORE AFS 150E WATER PURIFICATION SYSTEM 150 L/H CLRW OUTPUT CLRWZAFS62150 - MANUFACTURER: MILLIPORE SAS REFERENCE NO.: ZAFS62150 AFS 150E WATER PURIFICATION SYSTEM FEED WATER: POTABLE TAP WATER OUTPUT WATER: CLINICAL LABORATORY REAGENT WATER (CLRW) REAL-TIME MONITORING AND CONTROL INTUITIVE TOUCHSCREEN CONTROLLER RATED FLOW RATE: 150 L/H RESERVOIR: 140 L DISTRIBUTION PRESSURE: ADJUSTABLE 0.9 ... 2.1 BAR DAILY WATER USE: 3000 L/DAY POWER CONSUMPTION: 1100 VA POWER IPUT: 120V 60HZ S/N: CLRWZAFS62150

NEW-HAKKO T7/T15-1602 SOLDERING TIP FOR FM-202/FP-102 SPECIFICATIONS: PART #: T7/T15-1602 TIP SHAPE: FLAT PLATE FOR IRONS: HAKKO FM-203-HANDPIECE : HAKKO FM-2027(70W) HAKKO FM-204-HANDPIECE : HAKKO FM-2027(70W) HAKKO FX-950-HANDPIECE : HAKKO FM-2028(70W) HAKKO FX-951-HANDPIECE : HAKKO FM-2028(70W) HAKKO FX-952-HANDPIECE : HAKKO FM-2028(70W) HAKKO FM-202-HANDPIECE : HAKKO FM-2021(70W) OR HANDPIECE : HAKKO FM-2027(70W) NOTE: THE T15 TIPS HAVE REPLACED THE T7 TIPS. THE ONLY DIFFERENCE IS HAKKO HAS PHASED OUT THE BARCODE FROM THE TIPS. SEE THE?HAKKO PRODUCT BULLETIN. SKU: EBK38E008 1B-02-02(37) 0LBS - 6IN X 4IN X 6IN

[MEIJI EMZ-5 STEREOZOOM MICROSCOPE W/BOOM STAND +FIBER OPTIC LIGHT] - MANUFACTURER: MEIJI TECHNO MODEL: EMZ-5 CONDITION: REFURBISHED BY SELLER. THE SCOPE HEAD AND EYEPIECES ARE IN GOOD COSMETIC AND WORKING CONDITION. THE INTERNAL OBJECTIVE POSTS HAVE BEEN PROFESSIONALLY CLEANED AND LUBRICATED. ALL OF THE ITEMS HAVE SOME COSMETIC SCUFFS, SCRATCHES, PAINT CHIPS AND SIGNS OF NORMAL USE. HOWEVER, THIS DOES NOT AFFECT FUNCTIONALITY. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THE VIEW THROUGH THE SCOPE IS CLEAR AND ALIGNED WITH NO CHIPS, CRACKS OR FLAWS IN ANY OF THE OPTICS. THE FIBER OPTIC ILLUMINATOR RUNS QUIETLY AND ADJUSTS THROUGH ITS PROPER LOW LIGHT TO BRIGHT LIGHT RANGE (A NEW EKE BULB HAS BEEN INSTALLED). ALL OF THE FOCUS MOUNT/BOOM STAND MECHANICS FUNCTION NORMALLY. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) MEIJI EMZ-5 STEREOZOOM MICROSCOPE HEAD (2) MEIJI SWF10X SUPER WIDEFIELD EYEPIECES (1) MEIJI S-TYPE HEAVY BOOM STAND (1) MEIJI F-HOLDER FOCUS MOUNT (1) BOOM STAND RING LOCK (1) MEIJI MA517 0.5X AUXILIARY OBJECTIVE LENS (1) LUXO FOI-150-UL FIBER OPTIC LIGHT SOURCE W/VARIABLE LIGHT INTENSITY (1) 24" DOUBLE-GOOSENECK FIBER LIGHT GUIDES (1) NEW GE EKE 21V/150W BULB (INSTALLED IN THE ILLUMINATOR/LIGHT SOURCE) (1) POWER CORD FOR LIGHT SOURCE (1) COPY OF MEIJI EMZ SERIES MANUAL SPECIFICATIONS: MANUFACTURER: MEIJI TECHNO, JAPAN MODEL: EMZ-5 ZOOM RATIO: 6:5:1 ZOOM RANGE: 0.7X - 4.5X FIELD OF VIEW: 32MM - 5.1MM EYETUBE INCLINATION: 45O ZOOM CONTROL: DUAL, GRADUATED BODY-MOUNTED SIDE ZOOM CONTROLS BODY: BINOCULAR/STEREO HEAD, 360O ROTATION MAGNIFICATION: 3.5X - 22.5 (7X - 45X WITHOUT AUXILARY OBJECTIVE) WORKING DISTANCE: 150MM (93MM WITHOUT AUXILARY OBJECTIVE) ADJUSTABLE INTERPUPILLARY DISTANCE: 54MM - 75MM DUAL DIOPTRIC ADJUSTMENT: +/-5 DIOPTERS DOUGDEALS FACTOID: MEIJI MICROSCOPES ARE NAMED AFTER EMPEROR MUTSUHITO MEIJI (MEANING "THE ENLIGHTENED RULER"). DURING JAPAN'S MEIJI PERIOD (1868-1912), EMPEROR MEIJI MOVED FROM KYOTO (THE OLD CAPITAL OF JAPAN) TO TOKYO - WHICH BECAME THE NEW CAPITAL AND REMAINS SO TO THIS DAY. SKU: X10V001 3B-07-03(1) 57LBS - 25IN X 25IN X 20IN

[USED] THERMO PRECISION MICROPROCESSOR CONTROLLED 280 SERIES WATER BATH CAT # 51221050 MANUFACTURER: PRECISION MODEL: 51221050 DESCRIPTION: WATER BATH TEMP RATED: AMB +5C - 99.9C 120 VOLTS 400 WATTS 1 PH 3.5 AMPS 50/60 HZ CAPACITY: 3 GALLONS/ 12 LITERS 21LBS - 18IN X 18IN X 18IN

[AGILENT TECHNOLOGIES] HP E8793A VXI BUS 32X4 MATRIX MODULE RELAY MULTIPLEX CARD - MANUFACTURER: AGILENT MODEL: E8793A CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THIS CARD IS IN FAIR COSMETIC CONDITION, WITH SCUFFS/SCRATCHES/STAINS, HANDWRITING AND SMALL LABELS ON THE FRONT. THE CONNECTORS ON THE UNIT YOU RECEIVE MAY BE WHITE OR BLACK, AS SHOWN. NOTE: THIS SALE IS FOR ONLY ONE CARD, A FEW ARE SHOWN TO ILLUSTRATE THE VARIETY OF COSMETIC BLEMISHES YOU WILL FIND ON THE UNIT YOU RECEIVE. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: THIS CARD WAS REMOVED FROM A DECOMMISSIONED SYSTEM AND NOT TESTED SEPARATELY. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) AGILENT E8793A MATRIX CARD SPECIFICATIONS: MANUFACTURER: AGILENT TECHNOLOGIES MODEL: E8793A (E8793-81000) MATRIX CARD FOR VXI BUS 32X4 SWITCHING MATRIX MULTIPLEXES 4-WIRE ANALOG BUS (ABUS1-ABUS4) TO 32-PINS FOR THE UUT MAY BE USED FOR INCREASING CHANNELS IN INCREMENTS OF 32 ORIGINALLY INSTALLED IN TS-5400 FUNCTIONAL TEST SYSTEM SKU: Y38D001 2H-01-04(11) 5LBS - 18IN X 12IN X 5IN

[NTA INDUSTRIES 3501] STAINLESS STEEL CLEANROOM RACK 24" W X 7" D X 10" H. CONDITION: USED. THIS RACK IS IN GOOD COSMETIC CONDITION WITH MINOR SCUFFS AND SCRATCHES FROM REGULAR LABORATORY USE. THERE IS ALSO SOME ADHESIVE RESIDUE ON THE BACK SIDE AROUND EACH MOUNTING HOLE. COMES IN NON-ORIGINAL PACKAGING. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS RACK WAS REMOVED FROM A DECOMMISSIONED ENVIRONMENT AND HAS NOT BEEN TESTED, BUT WE HAVE CONFIRMED THE STRUCTURAL INTEGRITY OF THE UNIT. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) NTA INDUSTRIES 3501 STAINLESS STEEL CLEANROOM RACK 24" W X 7" D X 10" H SPECIFICATIONS: MANUFACTURER: NTA INDUSTRIES CLEAN ROOM FURNISHINGS MODEL: 3501 DESCRIPTION: CLEANROOM RACK STAINLESS STEEL 24" W X 7" D X 10" H (4) REAR MOUNTING HOLES SKU: Y07H015 1B-16-04(1) 15LBS - 28IN X 17IN X 14IN

[HEWLETT PACKARD] HP 6624A SYSTEM DC POWER SUPPLY FOUR, 40 WATT OUTPUTS MAXIMUM OUTPUTS: CHANNELS 1 & 2: 7V 5A / 20V 2A CHANNELS 3 & 4: 20V 2A / 50V 0.8A TWO RANGES FOR EACH OUTPUT (0-7V AND 0-20V, 0-20V AND 0-50V) INDIVIDUALLY PROGRAMMABLE OUTPUTS REMOTE SENSE CAPABLE GPIB COMMUNICATIONS RACK MOUNTING TABS AND SIDE HANDLES (NO FEET) POWER INPUT REQUIREMENT: 100/120/220/240 50/60HZ - MANUFACTURER: HEWLETT PACKARD HP MODEL: 6624A CONDITION: FOR PARTS OR NOT WORKING. COMES IN NON-ORIGINAL PACKAGING. THIS POWER SUPPLY IS IN FAIR COSMETIC CONDITION WITH LOTS OF MINOR SCUFFS/SCRATCHES/STAINS FROM PRIOR USE. THE PLASTIC BRACKETS THAT HIDE THE ENDS OF THE HANDLES ARE CRACKED AND BROKEN. THE NOTE ON TOP SAYS "OVER TEMP AGAIN! EVEN AFTER VACUUMING". THIS SUPPLY IS IN PARTIAL WORKING CONDITION. IT POWERS ON AND GIVES A MESSAGE "HDS ERR CH 1". THE KEYBOARD DOES NOT RESPOND TO BUTTON PRESSES. THE DISPLAY WORKS. THE FAN WORKS. WE ARE NOT ABLE TO TEST THE HP-IB INTERFACE. NO OTHER TESTING WAS DONE. THIS IS BEING SOLD AS/IS. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) HP 6624A SYSTEM DC POWER SUPPLY SPECIFICATIONS: MANUFACTURER: HEWLETT PACKARD MODEL: 6624A SYSTEM DC POWER SUPPLY FOUR, 40 WATT OUTPUTS MAXIMUM OUTPUTS: CHANNELS 1 & 2: 7V 5A / 20V 2A CHANNELS 3 & 4: 20V 2A / 50V 0.8A TWO RANGES FOR EACH OUTPUT (0-7V AND 0-20V, 0-20V AND 0-50V) INDIVIDUALLY PROGRAMMABLE OUTPUTS REMOTE SENSE CAPABLE GPIB COMMUNICATIONS RACK MOUNTING TABS AND SIDE HANDLES (NO FEET) POWER INPUT REQUIREMENT: 100/120/220/240 50/60HZ SKU: Y35D011 5B-18-02(1) 48LBS - 25IN X 25IN X 12IN

[TOKYO RIKAKIKAI] EYELA COOL ACE CA-3300 RECIRCULATING WATER CHILLER - PARTS - MANUFACTURER: TOKYO RIKAKIKAI MODEL: CA-3300 CONDITION: FOR PARTS OR NOT WORKING. THIS SYSTEM IS IN GOOD COSMETIC CONDITION WITH JUST A FEW NOTABLE BLEMISHES. SOME OF THE CONTROL PANEL HAS BEEN CLEANED TO THE POINT THAT IT HAS A DIFFERENT TEXTURE. THE WATER LEVEL AND CONTROL KNOB HAVE LINES SCRATCHED INTO THE FINISH NEXT TO THEM. THERE IS A FAINT GREEN FILM AROUND THE FULL-WATER LEVEL IN THE RESERVOIR, AND VERY FAINT TRACES AT THE FULL MARK ON THE LEVEL METER. THE RESERVOIR HAS SOME WATER SPOTS INSIDE. OTHERWISE, IT LOOKS PRETTY CLEAN. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS CHILLER IS IN MOSTLY-WORKING CONDITION. SOMETIMES, FOR NO REASON WE CAN DISCERN, THE REFRIGERATION SECTION WON'T TURN ON. SOMETIMES SWITCHING OFF AND ON AGAIN MADE IT START, AND SOMETIMES THE WHOLE SYSTEM WOULD HAVE TO BE OFF FOR A MOMENT. BUT THE REFRIGERATION, WHEN IT RUNS, WORKS WELL. THE PUMP, CONTROLS, AND TEMPERATURE ADJUSTMENT ALSO WORK. WE FILLED THE RESERVOIR WITH TAP WATER ABOUT 14O, AND SET MINIMUM TEMPERATURE. THE TEMPERATURE FELL TO 3O IN JUST 10 MINUTES, AND WE STOPPED TESTING TO PREVENT FREEZING UP THE WHOLE WORKS WITH ICE. NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) EYELA CA-3300 CHILLER SPECIFICATIONS: MANUFACTURER: TOKYO RIKAKIKAI CO., LTD. EYELA MODEL: COOL ACE CA-3300 WATER CHILLER (LOW-TEMPERATURE CIRCULATOR) WATER-COOLED R-404 REFRIGERATION COOLING CAPACITY (APPROXIMATELY): 3KW TEMPERATURE RANGE: 5O TO 25OC SELF-CONTAINED RECIRCULATION PUMP STAINLESS STEEL RESERVOIR INTERNAL RESERVOIR VOLUME (APPROXIMATELY): 48 LITERS FRONT-PANEL LEVEL SIGHT GLASS AND CONTROLS DIGITAL TEMPERATURE CONTROLLER WITH DIGITAL DISPLAY PUMP: WPT-461 POWER: 200V 3PHASE 3.5KW SKU: T08D003

[HEIDOLPH PD 5001] GENERAL PURPOSE PERISTALTIC PUMP 10-120 RPM 0.005-861 L/MIN - MANUFACTURER: HEIDOLPH INSTRUMENTS MODEL: 523-50010-01-0 CONDITION: USED. THIS PUMP IS IN GOOD COSMETIC CONDITION WITH SCUFFS AND SCRATCHES FROM REGULAR COMMERCIAL USE AND COMES IN NON-ORIGINAL PACKAGING. THERE ARE SOME FADED STAINS ON THE TOP AND SIDE OF THE ENCLOSURE AND ON THE FRONT OF THE PUMP HEAD. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: WE POWERED ON THIS PUMP AND OBSERVED THE PERISTALTIC HEAD MOVE AS DESIGNED AND RESPONDED ACCORDINGLY TO THE SPEED CONTROL. NO ADDITIONAL TESTING WAS PERFORMED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) HEIDOLPH PD 5001 GENERAL PURPOSE PERISTALTIC PUMP SPECIFICATIONS: MANUFACTURER: HEIDOLPH MODEL: PD 5001 PART #: 523-50010-01-0 GENERAL PURPOSE PERISTALTIC PUMP 10-120 L/MIN IP30 0.005-861 L/MIN HEI-FLOW CORE 120 115VAC 50/60 HZ 150W MADE IN GERMANY SKU: Y09H021 5A-01-04(1) 19LBS - 12IN X 12IN X 12IN

CONVIRON TC16 ILLUMINATED TEMPERATURE/HUMIDITY TISSUE/PLANT GROWTH CHAMBER-PARTS - MANUFACTURER: CONVIRON MODEL: TC16 CONDITION: FOR PARTS OR NOT WORKING. THIS CHAMBER IS IN FAIR COSMETIC CONDITION. THERE ARE SOME ADHESIVE LABEL RESIDUES OUTSIDE, BUT THE WHOLE SYSTEM LOOKS PRETTY CLEAN AT A GLANCE. THE INSIDE HAS A MILD MUSTY/HUMID ODOR. ON THE SHELF DIRECTLY BENEATH THE LOUD FAN IS AN AREA WITH SOME DISCOLORATION AND RESIDUE, WE ARE NOT SURE WHAT THIS MAY BE. THERE IS RESIDUE AND CORROSION VISIBLE IN THE REFRIGERATION SECTION, MOST NOTABLY WHAT APPEARS TO BE RUST-THROUGH OF SOME METAL BENEATH THE COMPRESSOR ITSELF. PLEASE NOTE: WE DO NOT HAVE ANY KEYS FOR THE DOOR OR CONTROL PANEL LOCKS. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS CHAMBER IS IN PARTIAL WORKING CONDITION. THE LIGHTS WORK AND THE HEATER WORKS. WE DID NOT PERFORM THOROUGH TESTING TO FIND THE MAXIMUM TEMPERATURE BUT THE READING INCREASED WHEN THE LIGHTS WERE OFF AND THE HEATING INDICATION WAS ON. THE FLUORESCENT TUBES TOOK A LITTLE WHILE TO STRIKE AND WARM UP BUT THEY ALL CAME ON BRIGHT EVENTUALLY. THE REFRIGERATION SYSTEM WAS UNPLUGGED WHEN WE GOT THIS. WE PLUGGED IT IN AND THE SYSTEM WAS ABLE TO RUN THE COMPRESSOR AND CONDENSER FAN, AND THE PIPING ON THE REFRIGERATION GOT WARM . . . BUT THE CHAMBER TEMPERATURE INCREASED WITH THE COOLING SYSTEM RUNNING. THE CIRCULATION FAN ON THE RIGHT SIDE (OVER THE NASTY STUFF ON THE SHELF) RUNS VERY LOUD AND VIBRATES. THE HUMIDITY SYSTEM ALWAYS GIVES AN ERROR, POSSIBLY DUE TO HAVING NO WATER CONNECTED DURING TESTING. NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) CONVIRON TC16 ENVIRONMENTAL CHAMBER (1) CHARACTERIZATION TABLE (1) CMP BLOCK DIAGRAM (1) ELECTRICAL SCHEMATIC SPECIFICATIONS: MANUFACTURER: CONTROLLED ENVIRONMENTS LTD. MODEL: TC16 CONVIRON TISSUE CULTURE CHAMBER HEATED/COOLED, HUMIDITY CONTROLLED, ILLUMINATED GROWTH ENVIRONMENT IDEAL FOR PETRI DISHES OR SMALL/YOUNG PLANTS (4) TIERS OF REACH-IN CULTURE/CULTIVATION/RESEARCH TOP-MOUNTED REFRIGERATION SYSTEM SHELF AREA: 26"W X 27.5"D X 8.75"H (2) PASSTHROUGH PORTS ON BOTTOM/LEFT SIDE (1) SAMPLINGPORT ON TOP/LEFT SIDE BRACKETS FOR ADJUSTABLE RACK SHELVES (NO BRACKETS/SHELVES INCLUDED) REFRIGERATION: R22 HEATER: 2.3A FACILITY REQUIREMENT: 120V 60HZ 17.5A PLUS DEMINERALIZED WATER SKU: X06D011 5I-14-01(1) 490LBS - 48IN X 40IN X 86IN

[NEW] ULTRA-X RST PRO2 PCI RAM MEMORY STRESS TESTER PROFESSIONAL PC DIAGNOSTIC R.S.T. - MANUFACTURER: ULTRA-X MODEL: RSTPRO2 CONDITION: NEW OTHER. COMES IN NON-ORIGINAL PACKAGING.A THIS LOT IS IN GOOD COSMETIC CONDITION WITH MINOR 'SHELF WEAR'.A THE SERIAL NUMBERS ON THE CASE AND THE CARD MATCH, AND THE CARD IS SEALED WITH AN ANTISTATIC STICKER IN AN ANTISTATIC BAG.A THE CARD WHICH IS OUT OF BAG IN PHOTOS IS A TYPICAL UNIT THAT WAS NOT SEALED WHEN WE RECEIVED THESE; YOU WILL RECEIVE A SEALED CARD.A THE SHOWN CASE IS ABOUT THE WORST-LOOKING OF ALL THE UNITS WE HAVE - THE UNIT YOU RECEIVE MAY LOOK QUITE A BIT BETTER. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). NOTES: NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) RSTPRO2 TESTING CARD (1) SERIAL CABLE (1) CASE (1) R.S.T. PRO USER'S GUIDE (1) ULTRA-X PRODUCT CATALOG (1) WARRANTY INSERT SPECIFICATIONS: MANUFACTURER: ULTRA-X, INC. MODEL: R.S.T. PRO2 MEMORY DIAGNOSTIC & VALIDATION TOOL WITH SERIAL PORT FOR DATALOGGING QUICKLY AND ACCURATELY TEST AND VALIDATE MEMORY IN DESKTOPS, SERVERS, AND WORKSTATIONS FOR USE WITH INTEL OR AMD X86 COMPATIBLE 32/64-BIT SINGLE OR MULTI-CORE PROCESSORS FOR BOTH BASE AND EXTENDED MEMORY TEST UP TO 64 GIGABYTES USES OVER 100 TEST PATTERNS AND ALGORITHMS GRAPHIC DISPLAY PINPOINTS EXACT LOCATION OF MEMORY FAILURES SUPPORTS THE LATEST SIMM, DIMM, RIMM SRAM, RDRAM (RAMBUS), ECC, FB-DIMM, PARITY AND NON-PARITY MEMORY TECHNOLOGIES SUPPORTS DDR-266/333/366/400/466/500, DDR2-533/667/800/1066 SELF-BOOT TECHNOLOGY TESTS MEMORY WITHOUT INTERFACE OF ANY DRIVER, TSR OR OPERATING SYSTEM LIMITATIONS SKU: N28D006 4C-04-06(3) 4LBS - 15IN X 12IN X 7IN

ASSOCIATED TESTING LABORATORIES RK-1101 CONVECTION TEMPERATURE TEST CHAMBER 1 CU.FT. LOW-HIGH TEMPERATURE ENVIRONMENTAL TESTING CHAMBER STAINLESS STEEL INTERIOR ANALOG THERMOSTATIC CONTROL ADJUSTABLE OVERTEMPERATURE FAILSAFE INDIVIDUALLY SELECTABLE HEAT AND COOLING COOLING METHOD: 300 PSIG CO2 INJECTION USABLE INTERIOR VOLUME: 10.5"W X 13"D X 11"H (JUST UNDER 1 CUBIC FOOT) 3" PORT ON LEFT SIDE BRACKETS TO SUPPORT 2 SHELVES POWER REQUIREMENT: 115V 60HZ 8A

GLOBAL SCIENTIFIC 113148R 16MM POLYETHYLENE SNAP CAP - RED (1000) SNAP CAP FOR USE WITH VACUUM AND GLASS TUBES 16MM RED POLYETHYLENE (LDPE) NON-STERILE SKU: W12H036 1B-04-04(8) 4LBS - 16IN X 12IN X 8IN

[PRA 66343] TEMPERATURE TEST CHAMBER WITH BURN-IN FIXTURES, NO CONTROLLER. MANUFACTURER: PRA, INC. MODEL: 66343 TEMPERATURE TEST CHAMBER. CO2 OR LN2 COOLED, SHIELDED HEATER ROD. OPERATES IN REMOTE CONTROL MODE ONLY. TEST CAVITY: 19" X 25" X 18" DEEP. RS-232 COM PORT INTERFACE. CAN BE DAISY-CHAINED WITH MULTIPLE CHAMBERS. FRONT PANEL STATUS INDICATORS. STAINLESS STEEL INTERIOR. POWER: 190 TO 260V 50/60HZ 6.5KVA MAXIMUM, SINGLE PHASE. CONDITION: FOR PARTS OR NOT WORKING. FAIR COSMETIC CONDITION WITH MINOR SCUFFS/SCRATCHES AND STAINS FROM PRIOR USE. TESTING STATIONS HAVE VARIOUS PROBLEMS. WIRES ARE PROTRUDING THROUGH THE SIDE OF THE CHAMBER. PARTIAL WORKING CONDITION: WHEN POWER IS TURNED ON, A GREEN COM LIGHT SHOWS ON THE INDICATOR PANEL AND THE FANS ON THE TOP/REAR OF THE CABINET START BLOWING. NOTHING ELSE HAPPENS. NO FURTHER TESTING WAS DONE. UNIT ONLY OPERATES IN REMOTE-CONTROLLED MODE AND CONTROLLER OR SOFTWARE IS NOT INCLUDED. SALE IS AS-IS. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) PRA 66343 TEMPERATURE TEST CHAMBER. SKU: W34D002 5A-11-04(1) 285LBS - 48IN X 40IN X 44IN

[STOCKER & YALE IMAGELITE #20] LITE MITE LIGHT SOURCE. MANUFACTURER: STOCKER AND YALE MODEL: IMAGELITE #20 LINE: 110-120 VOLTS POWERL: 230 VA MAX. ITEM HAS MINOR SCUFFS AND SCRATCHES FROM PREVIOUS USE. WE PLUGGED THIS ITEM IN AND IT CAME ON. NO FURTHER TESTING WAS PERFORMED. THIS ITEM DOES NOT INCLUDE THE POWER CORD OR LIGHT CABLES. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN.

2016 SP SCIENTIFIC VT455 VAPOR TRAP WITH GLASS LINER -48 MECHANICALLY REFRIGERATED, AIR-COOLED DIGITAL TEMPERATURE DISPLAY STAINLESS STEEL CHAMBER GLASS INSERT VESSEL/VAPOR TRAP BOTTLE SAVANT FC400 RUBBER TOP FOR PLUMBING TO THE GLASS LINER COPPER MESH HEAT TRANSFER JACKET REFRIGERANT: R-1270 POWER: 120V 60HZ 7A RATED OPERATING TEMPERATURE: -50O CHAMBER VOLUME: 4 LITERS TRAPPING RATE: 3 LITERS/24 HOURS

CORNING 430771 VACUUM FILTER/STORAGE BOTTLE SYSTEM 250ML 0.2UM (8) - VACUUM FILTER/STORAGE BOTTLE SYSTEM BOTTLE CAPACITY: 250 ML MEMBRANE MATERIAL: NYLON MEMBRANE PORE SIZE: 0.2 M MEMBRANE AREA: 19.6 CM2 NECK DIAMETER: 45 MM

[VWR] 76360-496 8-UPPER HOLDER/8-LOWER HOLDER UNIVERSAL CAROUSEL PIPETTE STAND DUAL LEVEL 8 UPPER HOLDING SLOTS AND 8 LOWER HOLDING SPOTS MATERIAL: ABS PLASTIC COLOR: WHITE BASE, PURPLE LOWER HOLDER, PURPLE UPPER HOLDER THE UNIT IS NON-AUTOCLAVABLE BUT CAN BE CLEANED WITH SOAP AND WATER OR LABORATORY DISINFECTANTS DIMENSIONS: 16.1"H X 9"W BASE DIAMETER: 6.2" WEIGHTED BASE TO PREVENT TIPPING

[METCAL SMTC-1158] SOLDERING IRON CARTRIDGE QUAD 304-P QFP DUAL HEATER. SPECIFICATIONS: MANUFACTURER: METCAL MODEL: SMTC-1158 DESCRIPTION: METCAL SMTC-158 SOLDERING IRON CARTRIDGE QUAD 304-P QFP DUAL HEATER PRODUCT: SOLDERING TIP TYPE: QUAD TIP SIZE: 1.6" SMTC SOLDERING QUAD TIP 700 SERIES 1.6 IN, DUAL HEATER QFP-304

[UNBRANDED] [DOES NOT APPLY] 5-SHELF HORIZONTAL LABORATORY FREEZER RACK 22"L X 11"H X 5.25"W STAINLESS STEEL. MANUFACTURER: UNBRANDED, MODEL: DOES NOT APPLY, LABORATORY FREEZER RACK, ORIENTATION: HORIZONTAL, TOTAL LENGTH: 22", TOTAL HEIGHT: 12", WIDTH: 5.30", CONSTRUCTION: STAINLESS STEEL, 5-SHELF DESIGN. SKU: W38B018 1D-07-04(2). THE RACK IS IN GOOD, USED CONDITION WITH SOME MINOR SCUFFS AND SCRATCHES FROM PREVIOUS USE. COSMETIC APPEARANCE MAY VARY SLIGHTLY FROM PICTURED UNIT(S). THE RACK WAS REMOVED FROM A DECOMMISSIONED ENVIRONMENT. NO FURTHER TESTING WAS PERFORMED AFTER REMOVAL. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN.

YAMAICHI IC51-1284-1433 BURN-IN IC 0.5MM PITCH QFP TEST SOCKET 128-PIN SOLDER. MANUFACTURER: YAMAICHI. MODEL: IC51-1284-1433. CONDITION: NEW OTHER. COMES IN NON-ORIGINAL PACKAGING. THIS TEST SOCKET IS BRAND NEW AND HAS BEEN REPACKED WITH ESD FOAM INSIDE OF AN ESD BAG. NOTES: NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) YAMAICHI IC51-1284-1433 BURN-IN IC 0.5MM PITCH QFP TEST SOCKET. SPECIFICATIONS: MANUFACTURER: YAMAICHI. MODEL: IC51-1284-1433. DESCRIPTION: BURN-IN/TEST SOCKET. PRODUCT TYPE: QFP (QUAD FLAT PACK). BODY TYPE: CLAMSHELL. # OF CONTACTS: 128-PINS. PITCH: 0.5 MM. BODY SIZE: 46MM X 43MM. WEIGHT: 0.10 LBS. SKU: P35P005 1B-10-02(10) 0LBS - 6IN X 6IN X 4IN

[WINWAY SAPB9901540REV1] SOCKET AMD BGA27X31-0 OLD FP2 BACKPLATES - MANUFACTURER: WINWAY MODEL: SAPB9901540REV1 CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THIS LOT INCLUDES 29 TIMES WHAT YOU CAN SEE IN PICTURE 3. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THESE OLD BACKPLATES WERE PULLED FROM A WORKING SETUP THAT WAS BEING DECOMMISSIONED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (29) WINWAY TECH SAPB9901540REV1 OLD FP2 BACKPLATES SPECIFICATIONS: MANUFACTURER: WINWAY TECHNOLOGY MODEL: SAPB9901540REV1 DESCRIPTION: OLD FP2 BACKPLATES TOTAL WEIGHT: 2.40 LBS. CONDITION: USED QUANTITY: 29 SKU: P12P015 1B-13-02(1) 4LBS - 17IN X 11IN X 6IN

FS FHOM-101 HIMM HANDHELD INTELLIGENT MULTIMETER OPTICAL POWER METER, OPTICAL LIGHT SOURCE, AND FAULT LOCATOR IN ONE PACKAGE INPUT RANGE: -50 TO +26 DBM OUTPUT POWER: -5 DBM INTERCHANGEABLE CONNECTOR ADAPTERS USE USB POWER CHARGER OR 3X "AA" BATTERIES BACKLIT DISPLAY MEASURES 850, 1300, 1310, 1490, 1550, 1625 NM OUTPUTS 1310,1550 NM

SHELDON 1013AG AGILENT G2545A HYBRIDIZATION OVEN INCUBATOR (NO ROTOR) SHEL LABS - MANUFACTURER: SHELDON MANUFACTURING (SHEL LABS) P/N: 1013AG HYBRIDIZATION OVEN AGILENT MODEL: G2545A STAINLESS STEEL INTERIOR ADJUSTABLE TEMPERATURE AMBIENT +5O TO 70OC ADJUSTABLE ROTOR SPEED 2RPM TO 20RPM APPROXIMATE CHAMBER DIMENSIONS: 14.5"H X 12.5"W X 12"D POWER: 100-120V 50/60HZ 5A. THIS OVEN IS IN GOOD COSMETIC CONDITION WITH ONLY MINOR BLEMISHES FROM PRIOR USE. THERE ARE LOTS OF SHALLOW SCUFFS/SCRATCHES ON THE TOP. THE ROTATOR IS MISSING. THIS UNIT IS IN GOOD WORKING CONDITION. TEMPERATURE CONTROL WORKS AND THE CHAMBER HEATS FAIRLY QUICKLY. THE ROTOR SPINNER RUNS AT THE SPEED SET ON THE DIAL. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN.

[7] THERMO SCIENTIFIC 596-4520 SINGLE USE STERILE BOTTLE TOP FILTERS VOLUME: 150 ML PORE SIZE: 0.2M FITS BOTTLE NECK SIZE: 45MM MATERIAL: POLYETHERSULFONE

[FTS SYSTEMS XE753 AIR-JET XE PRECISION TEMPERATURE CYCLING SYSTEM] - POOR HEATING CONTROL - MANUFACTURER: FTS SYSTEMS MODEL: XE753_01 AIR-JET XE PRECISION TEMPERATURE CYCLING SYSTEM TEMPERATURE RANGE: -75OC TO +225OC THERMAL FORCING UNIT FITS ON THE BENCHTOP SELF-CONTAINED ONLY REQUIRES DRY AIR, NO NITROGEN REQUIRED! MONITOR AND CONTROL FROM AN INTERNAL OR EXTERNAL (SAMPLE-MOUNTED) THERMOCOUPLE SAVE MULTI-STEP PROFILES IN THE WATLOW F4 DIGITAL CONTROLLER RS-232 OR GPIB (IEEE_488) PROGRAMMABILITY TO INTERFACE WITH AUTOMATED TEST EQUIPMENT FLOW RATES AJUSTABLE FROM 1.0 TO 4.0 SCFM (2.0 SCFM GIVES BEST TEMPERATURE CONTROL RANGE) SMALL ENOUGH TO BE RACK-MOUNTED REFRIGERATION UNIT DIMENSIONS: 24" X 15" X 16"H (APPROXIMATELY) BUILT-IN OVERTEMPERATURE SAFETY BUILT-IN LOW-FLOW SAFETY PID DIGITAL CONTROLLER RATED FOR +/-0.5O STABILITY AND REPEATABILITY (PLEASE READ TESTING NOTES!) CONTROL UNIT DIMENSIONS: 10" X 8" X 7" (APPROXIMATELY) TRANSITION SPECIFICATIONS @ 2SCFM (PLEASE READ TESTING NOTES!) -55OC TO +125OC <10 SECONDS +125OC TO -55OC <20 SECONDS POWER: 220V 50HZ (COMPATIBLE WITH 230V 60HZ) REQUIRES CLEAN DRY AIR, 7SCFM WITH -80OC DEWPOINT NO THERMAL CAPS (SAMPLE ENCLOSURES) ARE INCLUDED (1) REFRIGERATION UNIT WITH OUTPUT HOSE ATTACHED (1) CONTROLLER (1) CONNECTION CABLE

[HEWLETT PACKARD] HP 6032A SYSTEM DC POWER SUPPLY 1000W 0-60V 0-50A 120VIN RUNAWAY VOLTS OUT-PARTS - MANUFACTURER: HEWLETT PACKARD HP MODEL: 6032A CONDITION: FOR PARTS OR NOT WORKING. COMES IN NON-ORIGINAL PACKAGING. THIS SUPPLY IS IN FAIR COSMETIC CONDITION, WITH LOTS OF MINOR SCUFFS/SCRATCHES AND RESIDUES FROM PRIOR USE. THE MAIN INPUT COVER IS MISSING. ON THE REAR PANEL, THE 01 DIP SWITCHES AND S+/S- TERMINALS ARE CROOKED, AND FEEL LOOSE. THE IP AND GROUNDP TERMINALS ARE MISSING THEIR SCREWS. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS SUPPLY IS IN PARTIAL WORKING CONDITION. WHEN NO LOAD IS APPLIED, IMMEDIATELY AFTER POWER-ON, THE OUTPUT VOLTAGE CLIMBS RAPIDLY (A FEW SECONDS) UNTIL IT EXCEEDS THE OVERVOLTAGE SAFETY SET POINT. WE QUICKLY APPLIED A 10 AMP LOAD AND FOUND THE VOLTAGE STOPPED RISING OUT OF CONTROL ... AND INSTEAD, WOULDN'T RISE OVER 1 VOLT. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) HP 6032A POWER SUPPLY SPECIFICATIONS: MANUFACTURER: HEWLETT PACKARD MODEL: 6032A SYSTEM POWER SUPPLY HP-IB COMMUNICATIONS/PROGRAMMING (FAILED!) OUTPUT: 0 TO 60V DC, 0 TO 50 AMPS, 1064 WATTS MAX. INPUT: 120V 48-63HZ 24A MAX. NOT WORKING PROPERLY! SOLD AS-IS! SKU: Y34D004 2B-01-01(1) 40LBS - 23IN X 23IN X 10IN

[AEROTECH] AWT-100 FIBER OPTIC CONNECTOR INSPECTOR KIT WITH LCD SCREEN, PROBE, AV IN CABLE, AND POWER ADAPTER. IMAGE: MONOCHROME GEOMETRIC MAGNIFICATION X12. MAGNIFICATION ON 4" MONITOR X 200. APPROX. STANDARD SVHS VIDEO SIGNAL. ILLUMINATION: INTERNAL IMAGE ILLUMINATION, EXTERNAL SIGHTING TORCH. DISPLAY: STANDARD 4" LCD MONITOR. POWER: BATTERY OR POWER ADAPTER. SPECIFICATIONS: MANUFACTURER: AEROTECH WORLD TRADE, MODEL: AWT-100, IMAGE: MONOCHROME GEOMETRIC MAGNIFICATION X12, MAGNIFICATION ON 4" MONITOR X 200, APPROX. STANDARD SVHS VIDEO SIGNAL, ILLUMINATION: INTERNAL IMAGE ILLUMINATION EXTERNAL SIGHTING TORCH TO ASSIST ENGAGEMENT, DISPLAY: STANDARD 4" LCD MONITOR, POWER: BATTERY OR POWER ADAPTER.

KINETIC SYSTEMS INC. 1201-01-11 VIBRATION ISOLATION 35" X 30" PNEUMATIC AIR TABLE - MANUFACTURER: KINETIC SYSTEMS KS MODEL: 1201-01-11 CONDITION: FOR PARTS OR NOT WORKING. THIS TABLE IS IN FAIR COSMETIC CONDITION, WITH MINOR BLEMISHES FROM PRIOR USE. THERE ARE LOTS OF SCUFFS AND SCRATCHES AS WELL AS LIGHT STAINS IN THE WHITE TOP, AND SCRATCHES IN THE BLACK PAINT AS WELL. FROM A FEW FEET AWAY IT LOOKS PRETTY GOOD. PHOTO #5 SHOWS A CLOSEUP OF THE TOP SURFACE, TO GIVE AN IDEA WHAT WE MEAN. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS TABLE IS IN PARTIAL WORKING CONDITION. THE TOP DOES NOT LIFT WITH NORMAL/LOW PRESSURE INPUT (E.G. 20 PSI) THE TOP DOES LIFT WITH 80PSI INPUT TO THE HEIGHT ADJUSTERS, BUT RESPONSE TO CHANGING BALANCE OR WEIGHT ON THE TABLE TOP IS VERY SLOW. IT'S SLOW ENOUGH THAT IT TOOK SEVERAL MINUTES TO SETTLE DOWN AND STOP OVERCORRECTING ITSELF DURING INITIAL INFLATION. MOVING LOADS MAY NEVER SETTLE PROPERLY! WHEN THE TOP FINALLY SETTLED DOWN, THE ADJUSTER TIED TO TWO LEGS CONTINUALLY BLED OFF AIR. WE ARE NOT SURE WHY. NO OTHER TESTING WAS DONE. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) KS 1201-01-11 VIBRATION899 ISOLATION TABLE SPECIFICATIONS: MANUFACTURER: KINETIC SYSTEMS INC. MODEL: 1201-01-11 VIBRATION ISOLATION WORKSTATION TABLE TOP DIMENSIONS: 35" X 30" TOP HEIGHT FROM FLOOR, APPROXIMATE: 30" HIGH PERFORMANCE ACTIVE-AIR SUSPENSION 3-ZONE SUSPENSION, RIGHT/LEFT/BACK AUTOMATIC LEVELING AND HEIGHT CONTROL BUMPER RAILS ON BOTH SIDES TO PREVENT OPERATORS DISTURBING THE TOP SUITABLE FOR MOVING LOADS AND HIGH CENTERS OF GRAVITY ULTRA LOW VERTICAL NATURAL FREQUENCIES ISOLATION EFFICIENCY APPROACHING 99% 1" THICK VIBRADAMPED STEEL TOP WITH PLASTIC LAMINATE SURFACE CLASS 100 CLEANROOM COMPATIBLE INPUT AND ISOLATOR AIR PRESSURE GAUGES INPUT AIR PRESSURE REGULATOR PERFORMANCE RATINGS: MIN. LOAD @ 20 PSI VERTICAL NATURAL FREQUENCY 2.1 HZ ISOLATION EFFICIENCY @ 5 HZ 43% ISOLATION EFFICIENCY @ 10 HZ 89% HORIZONTAL NATURAL FREQUENCY 3.5 HZ ISOLATION EFFICIENCY @ 5 HZ 40% ISOLATION EFFICIENCY @ 10 HZ 80% MAX. LOAD @ 80 PSI VERTICAL NATURAL FREQUENCY 1.6 HZ ISOLATION EFFICIENCY @ 5 HZ 76% ISOLATION EFFICIENCY @ 10 HZ 93% HORIZONTAL NATURAL FREQUENCY 2.5 HZ ISOLATION EFFICIENCY @ 5 HZ 75% ISOLATION EFFICIENCY @ 10 HZ 88% GROSS LOAD CAPACITY @ 80 PSI: 1300 LBS. (590 KG) ("HEAVY DUTY") SKU: W10D011 5A-10-04(1) 540LBS - 48IN X 40IN X 52IN

[SPARKFUN] DECADE RESISTANCE BOXES 0-1M PCBS (2) MANUFACTURER: SPARKFUN MODEL: KIT-13006 CONDITION: USED. COMES IN NON-ORIGINAL PACKAGING. THIS PAIR OF DECADE RESISTORS IS IN GOOD COSMETIC CONDITION WITH ONLY VERY MINOR MARKS FROM PRIOR USE OR HANDLING. THESE CAME FROM A BOX BURIED DEEP IN THE SHOP OF A MAN WHO WAS HAPPIER TO COLLECT TEST EQUIPMENT THAN TO USE IT; THEY MAY NOT HAVE BEEN ACTUALLY USED. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: WE GAVE THESE A QUICK CHECK WITH A MULTIMETER AND GOT THE EXPECTED RESISTANCE VALUES ON EVERY POSITION OF EVERY SWITCH. NO OTHER TESTING WAS PERFORMED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED:(2) SPARKFUN DECADE RESISTANCE BOXES SPECIFICATIONS: MANUFACTURER: SPARKFUN MODEL: KIT-13006 DECADE RESISTANCE BOX SELECT ANY RESISTANCE FROM ZERO TO 999,990 OHMS 10 INCREMENTS 3/4-TURN MECHANICAL SWITCHES BANANA JACK CONNECTIONS CORNERS ARE DRILLED FOR MOUNTING NO KNOBS, FACEPLATE, OR ANYTHING ELSE ARE INCLUDED SKU: Y04D007 1E-14-02(1) 2LBS - 7IN X 7IN X 7IN

[STARRETT] [4000-5368-01] LABORATORY GRADE N/A BLACK GRANITE SURFACE PLATE W/ LEG MOUNTS/SPACERS. MANUFACTURER: STARRETT. MODEL: 4000-5368-01. CONDITION: USED. THIS SURFACE PLATE AND HARDWARE IS IN GOOD COSMETIC CONDITION WITH SCUFFS, SCRATCHES, AND DISCOLORATION FROM REGULAR INDUSTRIAL USE. THE LEG MOUNTS ARE SECURELY ATTACHED TO THE GRANITE WITH BOLTS AND THE SPACERS ARE ALSO IN GOOD COSMETIC CONDITION. THE MOUNTING HOLES ARE CLEAR AND FUNCTIONAL. COMES IN NON-ORIGINAL PACKAGING. INCLUDED: (1) STARRETT LABORATORY GRADE N/A BLACK GRANITE SURFACE PLATE (4) LEG MOUNTS (4) SPACERS. SPECIFICATIONS: MANUFACTURER: STARRETT TRU-STONE TECHNOLOGIES DIVISION PART NUMBER: 4000-5368-01 DESCRIPTION: LABORATORY SURFACE PLATE WITH (4) LEG MOUNTS AND (4) SPACERS BLACK GRANITE GRADE N/A TOTAL LENGTH: 66" TOTAL WIDTH: 40" TOTAL THICKNESS: 9-2/4" LIP THICKNESS: 6" W/ ANGLE CUT BACK TO PLATE AT BOTTOM (4) INDUSTRIAL ADJUSTABLE METAL SPACERS (4) INDUSTRIAL BLACK ANODIZED ALUMINUM LEG MOUNTS (ATTACHED W/ BOLTED HARDWARE) TOP (43) M7 - 1.0 THREADED MOUNTING HOLES (15) M6 - 1.0 THREADED MOUNTING HOLES FRONT LONG SIDE (2) 2" DIAMETER 6" DEEP NON THREADED HOLES (5) M6 - 1.0 THREADED MOUNTING HOLES BACK LONG SIDE (2) 2" DIAMETER 6" DEEP NON THREADED HOLES. SKU: X44H017 6-BILR1(1) 2592LBS - 74IN X 48IN X 18IN

[USED] DIAGNOSTIC INSTRUMENTS HR070-CMT 0.70X C-MOUNT CAMERA ADAPTER W/ HC CLAMP. THIS CAMERA ADAPTER WAS REMOVED FROM A WORKING LEICA DMIRE2. MANUFACTURER: DIAGNOSTIC INSTRUMENTS DI MODEL: HR070-CMT DESCRIPTION: C-MOUNT CAMERA ADAPTER W/ HC CLAMP POWER: 0.70X WEIGHT: 1.65 LBS.

[TEKTRONIX P6708] PCIE PCI EXPRESS MID-BUS DIFFERENTIAL LOGIC ANALYZER PROBE 8 CH. MANUFACTURER: TEKTRONIX MODEL: P6708 PCI EXPRESS MID-BUS DIFFERENTIAL LOGIC ANALYZER PROBE 8 CHANNELS FOR DESIGNS USING PCIE X1 AND X4 LINKS PCB ATTACHMENT: "CONNECTORLESS" COMPRESSION CSPRING MECHANISM (1) TEK P6708 PROBE

MICROMANIPULATOR FET PS 4 POWER SUPPLY 4 CHANNELS ADJUSTABLE ZERO ALL CHANNELS

[NEW] PALL VACUCAP 90 GAMMA-IRRADIATED FILTRATION DEVICE 90MM 0.2UM (2) MANUFACTURER: PALL MODEL: VACUCAP 90 GAMMA-IRRADIATED FILTRATION DEVICE SIZE: 90 MM EFFECTIVE FILTRATION AREA: 60 CM2 MEDIA/MEMBRANE: SUPOR (HYDROPHILIC POLYETHERSULFONE) PORE SIZE: 0.2 UM STERILE FEATURES INDIVIDUALLY ATTACHED TUBING CONNECTION: 1/4" HOSE BARB INNER TAPER IN. SPECIFICATIONS: MANUFACTURER: PALL MODEL: VACUCAP 90 GAMMA-IRRADIATED FILTRATION DEVICE SIZE: 90 MM EFFECTIVE FILTRATION AREA: 60 CM2 MEDIA/MEMBRANE: SUPOR (HYDROPHILIC POLYETHERSULFONE) PORE SIZE: 0.2 UM STERILE FEATURES INDIVIDUALLY ATTACHED TUBING CONNECTION: 1/4" HOSE BARB INNER TAPER IN. SKU: V21B017 1E-01-02(4) 0LBS - 8IN X 8IN X 7IN

[LIGHTHOUSE AMC CONTROLLER WITH 32-PORT UNIVERSAL MANIFOLD PARTICLE MONITOR PARTS] MANUFACTURER: LIGHTHOUSE WORLDWIDE SOLUTIONS MODEL: AMC MANIFOLD & CONTROLLER CONDITION: FOR PARTS OR NOT WORKING. THIS UNIT IS IN GOOD COSMETIC CONDITION ASIDE FROM SOME SCUFFING FROM HANDLING, ESPECIALLY ON THE FRONT PANEL. THE TOP PANEL IS MISSING. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: THIS UNIT IS IN PARTIAL WORKING CONDITION. THE PUMP PUMPS, AND THE CONTROLLER POWERS ON AND TRIES TO WORK, BUT THE SENSOR NEVER READS OK AND THE VACUUM LEVEL BOUNCES ALL OVER THE PLACE (+128 TO -256). WE USED THE TOUCHSCREEN INTERFACE TO MAKE THE MANIFOLD ROBOT MOVE IN BOTH DIRECTIONS (WE COULD HEAR IT STEPPING TO DIFFERENT PORTS INSIDE THE MANIFOLD). THE SCREEN IS A LITTLE DIM BUT QUITE USABLE. WE ARE NOT SURE WHAT MAY BE WRONG WITH THIS UNIT NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) LIGHTHOUSE AMC CONTROLLER & MANIFOLD SPECIFICATIONS: MANUFACTURER: LIGHTHOUSE WORLDWIDE SOLUTIONS UNIVERSAL MANIFOLD AND CONTROLLER INTEGRATED INTO ONE METAL ENCLOSURE PUMP, POWER SUPPLY, CONTROLLER, DISPLAY, MANIFOLD, ALL INCLUDED 32-PORT MANIFOLD SUPPORTS MULTIPLEXED MULTI-POINT AIRBORNE MATERIAL CONTAMINATION (AMC) MONITORING OMEGA FLOW CONTROLLER KNF NEUBERGER VACUUM PUMP TOUCHSCREEN COLOR LCD CONTROLLER INTERFACE SKU: N28D005 3A-05-02(1) 59LBS - 36IN X 25IN X 19IN

[METTLER TOLEDO AT201 ANALYTICAL BALANCE SCALE .01MG - 205G] WITH [RS-P42 PRINTER]. MANUFACTURER: METLER TOLEDO. MODEL: AT201. CONDITION: USED. THIS BALANCE AND PRINTER ARE IN GOOD COSMETIC CONDITION WITH SCUFFS AND SCRATCHES FROM NORMAL USE. ONE OF THE GLASS PANES ON THE ENCLOSURE IS CRACKED IN MULTIPLE PLACES AND TAPED IN PLACE. COMES IN NON-ORIGINAL PACKAGING. THE PHOTOS SHOW THE EXACT ITEM(S) THE BUYER WILL RECEIVE. NOTES: WE POWERED UP THIS BALANCE AND PRINTER AND OBSERVED THE LED DISPLAY FOR BOTH FUNCTIONING AS DESIGNED. THE LED WAS RESPONSIVE TO THE SCALE AND RENDERED WEIGHTS AS DESIGNED. THE PRINTER WAS RESPONSIVE TO THE SCALE AND PRINTED OUT A TEST RUN WHEN POWERED. NO ADDITIONAL TESTING WAS PERFORMED. NO MANUALS, CORDS/CABLES, OR ADDITIONAL ITEMS ARE INCLUDED IF NOT LISTED OR SHOWN. INCLUDED: (1) METTLER TOLEDO AT201 ANALYTICAL BALANCE (1) METTLER TOLEDO RS-P42 PRINTER FOR ANALYTICAL BALANCE. SPECIFICATIONS: MANUFACTURER: METTLER TOLEDO. MODEL: AT201 & RS-P42. DESCRIPTION: ANALYTICAL BALANCE WITH PRINTER. BALANCE AT201 .01MG - 205G. PRINTER RS-P42. SKU: V49H013. 3B-06-02(1). 32LBS - 25IN X 19IN X 16IN